kubota l4310

Folks, I have been a long time lurker on this forum but rarely post. I searched this question but didn't quite find exactly what I'm looking for. Here is my question: I have a 2000ish Kubota L4310 that is leaking hydo fluid from the condensation weep hole. It's not too bad, I just add a...

I'm looking at a used L4310 at an auction yard, which does not have the year published, it does have an FEL, and only a picture of the hours with "Shows 1200 hours". There is a video of the tractor and it sounds about right to me... The hours would have turned over at 9999, so I'm wondering...

Lights come one but it doesn't turn over. Battery is fully charged. New positive cable installed on battery and starter with the extra wire on the end that slides over the starter bolt. There's another thin wire that has a plastic type plug but not sure if that just dangles or should be...

Dealer put a new PTO clutch (split tractor open 2 engine hours ago) and am now noticing that when PTO is engaged I am not getting full power (i.e. it still slips). When mowing tall grass or close to the ground I see the mower shaft come to a stop. I do not notice a drop in RPM throughout the...

I was trying to top off the hydraulic but as soon as I let the filler cap off a lot of high pressure air (hot) comes out This tractor was just serviced and I am assuming they put new hydraulic oil/filter since they had to split the tractor open to replace PTO clutch Any lead appreciated!

It was time to fix steering cylinder leak, disassembly went fine, replacing all the seals and bushings while I’m there. Anyone know how to swap out the seal in the middle of the cylinder rod? Service manual is of little help except saying to replace worn parts. Parts manual shows an O-ring...

I see many posts about adding third function valves and many posts about T-ing the loader lines for backhoe hydraulics. Seems like it would be super simple to get feed & return from the pictured block… is there a Kubota or aftermarket part made for this purpose? Or a third function valve that...

Hi folks. Any help would be greatly appreciated! I lost any actuation of the 3pt hitch, and front end loader hydraulics on my l4310. Here is step by step what happened, in case i am missing something. I was using The L4310 HST to bush hog a field and popped a lynch pin from the mower deck...

My L4310 HST has about 1500 hours. Sudden situation. Fastest speed forward is slower than a turtle (in any gear) Reverse is very fast and the pedal can jam. No obvious linkage issues (quick visual). Plenty of hydraulic fluid. Any feedback much appreciated.

Hi, I am trying to sell my L4310 with cab and loader. It has over 2500 hours on it. We just had it serviced at just over 2500 and repaired what needed repairing. The AC feels like it needs a recharge though. What would be a good price for this tractor? I have seen anywhere from $15k to $30k...

I have a L4310 4wd HST Rops with around 2050 hours on it. In the last few weeks I noticed a small drip puddle on the floor under the right floorboard area. After some investigation the leak is coming from the hard tubing/piping interface with the hydraulic block. See picture #1, leak coming...

I have been doing a lot FEL work this past fall, and now noticing that the steering has become very loose. Like it takes 1/2 turn of the steering wheel before the wheels start moving in either direction. I don't feel any binding or difficulty in steering. I didn't have time to dig into it...

Bought a used kubota l4310 tractor and when I turn the key to the ON position no oil pressure or charge lights come on but the glow plug light does. Then after I start it the glow plug light never goes off. The battery charge test shows It is not charging. I had the alternator tested and shows...

How hard is it to change tie rods .after i get the nut off how do i get them out of there place

Just thought id try posting a pic of my tractor

Anyone know the part number for the transmission filter for a L4310 hydro 4 wheel drive non cab

All, I have been reading here for many months and appreciate everyone sharing their knowledge. I *think* I understand what I need to do to add some hydraulics, but was hoping to get some other eyes to "check my work." Situation: I just bought a low hours L4310 and separately, a Woods BH9000-1...

Have the correct (i think) filters, but am not sure of the correct procedure to change fluid. What about the oil in the FEL? How do you get it out? Looked at specs... 10.5 gallons total?

I've had my used L4310 in my possession for just over 100 hours. It's got about 2000 hours on it now. Just recently I noticed a slow oil leak on the lower plastic cover below the steering wheel, just above the floor board. After removing the plastic covers, it looks like I have a slow leak...

Using the new-to-me L4310 this past weekend and I realized that this tractor's front end loader does not have the float function. Is that a control valve block that can be replaced to include the float function?

Looking at a cream puff L4310 HST w/682 loader, 600 hours. Wants $14k. Is it worth it?

I am new to this tractor, has 400 hours on it and it appears there are issues with the transmission??? When the shift lever is placed in the mid range and you push on the foot pedal the tractor doesn't move, when placed in neutral position to start and push on the foot pedal the tractor will...

Hello all, Another question. Until I’m able to find manuals I’m looking for some help. On this tractor, the rear end show signs of some leaking and the site glass appears to be too clouded to see anything inside. This is the HST model, so I assume that this is Hydraulic oil. Can anyone...

I posted this in the attachment section as well, but wanted to throw it in here for y'all to see too. Hello all, I am in the process of cleaning up some property with my 4310 and LA680 loader. I have only been using the bucket so far, and I am getting to the point where I need a grapple to...

Hello all, I am in the process of cleaning up some property with my 4310 and LA680 loader. I have only been using the bucket so far, and I am getting to the point where I need a grapple to be more efficient. I have pondered my options, and I have come to a few solutions: 1: Add-A-Grapple...

Just acquired a Kubota L4310 Hst, the problem i am having is the transmission will not shift into low range,,works great in high range,,when shifting into low I can feel it go in but it will not stay,,I can hold pressure on the shift lever and it will pull but I can feel it trying to jump...

I have been out for a while, I am looking at a tractor and need advice. 1999 L4310 HST with factory cab and front end loader. It has 3087.2 hours. Anything in particular I need to check? I know I will probably need tires on the front. Anywho, I always have always depended on you guys for the...

I have had this tractor for two years. Shifting between the gear ranges is very difficult to near impossible (I muscled it into high range just once, and though it was stuck there forever). I am looking for advice as to how to go about figuring out if this is due to a mechanical problem or...

I was out Sunday cleaning up a bit in the horse pasture and while backing uphill, I heard a loud crack and the sound of fluid pouring out of the rear of the tractor. I had the back blade attached, but it was in the full up position and no other load. Any idea on what caused the issue seen...

I have a question, I have owned a 2000 kubota l4310 hst 4x4 for 16 yrs on my 100 acre farm, and it has preformed flawlessly all that time for bush hogging, mowing cleaning out horse barn, etc. Now my son is moving and wants me to take over his 2013 3720 4x4 e hydro with 7' belly mower, large...

I have a year 2000 L4310. A fairly heavy fuel leak started suddenly and seems to be coming from below the fuel tank. It lost about 2 gallons in 30 minutes after I shut the machine off, and finally quit when the tank ran dry. It looks like the whole steering column and controls need to be...

I wanted to put a SSQA on my older L4310 that has the LA681 loader. Kubota didn't make a SSQA at the time for theses tractors so I decided to find a later Kubota SSQA that would fit. The newest ones, the LA765 would work with a few modifications but Kubota only sells that by the part, not as a...

I need info on adding a rear remote hydraulic to a Kubota L4310 with a loader. Any info on parts, price, complexity, etc would be greatly appreciated.

I need info on adding a rear remote to an L4310. What is the best (cheapest, easiest, most effective) way to go about it. It does have a loader.

Looking for some insight on 2002 Kubota L4310 versus 2012 John Deere 3038e versus JD 4410. All have loaders with 4x4 and HST. All are from private sellers. All say they've been serviced and not been worked too hard. All seem in similarly good shape with about 75% of tire wear remaining...

Hi every one I'm Frank and I"m searching for the rear transmission case. And cylinder assembly case for 1998 to 2003 Kubota Tractor model L4310 GST. The same case fit also L3710DT/GST/HST and L4300DT L4300F L4610DT/GST/HST. And a repair manual for the 2003 Kubota L4310GST. I'm having problem...

my tractor sometimes wont turn over when turning the key. in the past after playing around with the pto switch it would start . Thats not working now. the stupid glow light has never worked right. it stays on all the time. not sure if that could have something to do with it. could someone...

Hi, we have a L4310 HST at church and are ready to get a FEL for it. I see several manufacturers that make aftermarket loaders like Woods, but what do people here have? Expecting to spend about $6000 for the whole getup. Too much or too little? Just want to make sure I vet out all vendors...

I have a leak from the hydraulic line near the steering cylinder at the front of the tractor. I bought the line from the dealer $130 (ouch). Was going to replace both until I saw the price. Do you have to bleed anything after you install the new lines?? I am getting conflicting info. Thx

I just bought this machine, and have only operated it for an hour or so in cold weather. The hydrostatic transmission gets stuck in forward so that it creeps when you take your foot of the pedal, is stops if you tap the reverse pedal. I have not had a chance to look into myself, but I...

I just bought a 2001 l4610 with a backhoe on it. The previous owner lost the 3 point hitch, so now I'm looking for one. Any ideas on where best to find one? Or any other tractors that will interchange the parts?

I've got a L4310 that has about 1500 hours on it. It operates in 2x4 as it should however I can not shift it into 4x4, the lever moves and their are no noises, anyone have any ideas before I take it to the dealer? Thanks

(NOTE: I recently had to hit my old starter with a hammer to get it to start. I did this twice and the 3rd time the hammer trick did not work, so I bought a new starter.) I hooked up the new starter and went to start the tractor and there was a buzzing sound from under the dash. Dash/ glow...

Anyone ever replace the inlet pipe for their HST? This is the pipe that connects to the filter on the right hand side. When I got the tractor the previous owner backed it into a rock of something and dented the pipe at the bend which tweaked it where it goes into the tractor. Result is a slow...

Hello, I am looking at a 2002 Kubota L4310 HST with 1300 hours on it. It comes with a loader. Asking price is $13,500. Is that a good deal for the number of hours? What should I be checking for in a used tractor such as this? I was looking at new tractors but the price is tempting for the size...

While I await the arrival of my owners manual and service manual I want to check the hydraulic fluid level in my L4310. I can't find a sight glass or a dipstick. I ran a clean rod down in the hole where the fluid is added and don't get anything on the rod. The hydraulics/hydrostatics work fine...

OK, I took the plunge and bought an 8 year old L4310 with 1137 hours on it. after running the new Land's Pride mower for a couple of hours I have some questions. First, any suggestions on reasonably priced bumpers/grill guards. I do a lot of mowing where the grass and weeds are as tall as the...

I'm thinking seriously about driving 200 miles to buy a Kubota L4310 today. It is 8 years old and has 1110 hours. It has R4 tires I think he said, Industrial instead of agricultural tires which he says are a heavier duty tire. They want $$9,850 for it. He says it came of a plantation and was...

I found a 4X4 Kubota L4310 with a LA681 loader, rear snow blade, and brush hog. The tractor has 651 hours on it and they are asking $17,900. Does this seam like a good price? Also can anyone comment on the quality of the Kubota L4310 and if there is anything I know before making such a major...

Noob here, i was in tsc looking at quick couplers for my 4310 rear remotes and im stuck. i see pioneer standard coupler, poppit coupler?? What kind does mine take, they are a break away connection. Any help would be much appreciated. thanks ray

I am trying to identify the controller by number of wires and color of wires on the controller. I do not have a repair manual or parts manual.

I have a Kubota L4310 Tractor. The glow plug comes on at the time of starting, and stays on for a considerable amount of time. This just started a day ago. Occasionally, it may go out, but then come back on again. 1) Will operating the tractor with it on, cause any damage? 2) How can I...

I have a kubota l 4310. I have a hydraulic thing with three plugs and three nuts nearthe brake pedals can I tap into that or do I have to buy the block from kubota?

I have a hydraulic valve by the front brake pedals next to the filter can I plumb into this to add remotes or do I have to get the block from kubota?

I need to replace the base and back seat covers on my L4310. I have not been able to find Kubota part #'s for these or any aftermarket covers. Can anyone offer any suggestions? Thank you.

First off this is not mine but a good friends. Was his grandfathers til he passed away last year. A little background. It had some major work done a year and a half a ago. All I know is that the connecting rod for the three point lift was bent and the top Plate cracked. All was replaced...

I have a L4310 that has heat and A/C. The A/C doesn't work at all, and I am curious how the system even works. I would expect to see some condenser lines and heater hoses going up to the top of the cab, but I have found none. Is the system straight electric? there is a 30 amp fuse for the...

I have done my research on spools and lines and such, and think I got that covered. What I am having trouble identifying is where to actually hookup the feed and return lines from the spool. I have done some forum searches and found another thread where a guy purchased a block that replaces...

My rear wheel bearing is shot. Does anyone know where to find instructions as to how to do the repair. (or can advise me of the method) I assume pull the spindle and the axle. Never done a bearing before, but I have all the tools and am mechanically inclined. Thanks for the help

I posted in another thread that my church may be getting a L4310 donated. Well it is official now and we are in the process of preping it for a new engine since the current one spun a rod and blew a hole in the block. We are going to get a new crate engine and not bother repairing the one we...

Hi there guys. I am new here and hoping to learn a lot about the Kubota L4310HST 4x4. Our church is getting one donated with a catch. It needs a new motor. The current owner was letting us use it, it hasn稚 been used in a couple years and is a spare, to mow the field when he was using his...

How do you adjust the relief valve pressure for a loader on a L4310 Kubota.

I changed the oil recently and am trying to find the dipstick.....I did find a plastic cap on the side of the block that opens easily and seems to look into the crankcase.?? How do check the oil on these things.....(new owner 2003 model) Any ideas.

During brushcutting with a Rhino SE6, my Kubota L4310 HST took about 45 mins of work to run the tempature to the second white line - the beginning of the RED line - when it boiled into the overflow tank:eek:. I was working at 2300 RPM (Just below the 2400 where the 540 rpm mark is located.) I...

Our local dealer has a Kubota L4310 GST 4x4 for sale,price is $6900 for the tractor and there are also some implements available for added cost. It looks a little worn but around here it was probably used to bush hog and that will cause a lot of the scratches and such. I foolishly forgot to...

I plan to add a 3rd Function to a L4310 HST w/LA682 FEL in order to run a grapple I am building. I have read, studied, and reviewed most of the grapple posts along with the 3rd function posts - however I still would like to know if other L4310 owners have attempted this - without going to the...

Hello all: How difficult is it to find rear housing parts for a L4310 , 2003 kubota tractor? Are there salvage yards for tractors? jt

The 4WD will not engage on my L4310. I recently had work done on a leaking hydraulic tube from the filter to the rear housing, along with new filter and fluid. A few days later the problem arose. Could it be related? Is this a quick, inexpensive fix? The tractor is in excellent shape otherwise...

I'm interested in getting opinions on what will be the best long term purchase for 16 acres of horse farm and pasture that I'm reviving right now. The previous owner let it grow up in trees and scrub and most fences that circle the property need to be cleared & replaced. I also have a 1/3 mile...

I have a 2000 KUBOTA L4310GST 4 X 4 Drive, 6-Way Top & Tilt Hydraulic Package with a Model La681fl Frontloader The Frontloader has developed problems with the raise-lower control When I got the tractor 2 mos ago it had a dead spot on the raise control More recently it will occasionally...

The tractor listed above has been a great unit for all the work I do around the farm with a tractor of this size, virtually bulletproof, however the glow plugs have ceased operating properly, I replaced the timer under the dash, but no luck, the dash lite goes on and stays on, sometimes goes...

6 years ago I bought this tractor new. Dealer said the Bush Hog loader would do more work, lifted higher, and cost less. So I went with it. I now have about 550 hours on the tractor. I have had a re-occuring problem stripping bolts out of the FEL mounting bracket. Each time it is the same...

Hi guy's Iam new to this site but would love some info! I got a 4310 4x4 that works great for the first half hour but slowley loses forward and reverse. The filters have been changed along with the hyd oil. The tractor works fine in the winter here in upstate N.Y. but this summer I have...

To make a long story short, I am planning to sell my tractor and implements. I am hoping to get some advice from this forum on what it is worth. I had a couple of back surgeries and did not get all the results I had hoped for. I plan to sell the equipment in the next few months. I live in N...

A Friend has a L4310 while cutting with a finshing mower the tractor choked on a dirt mound and went dead. When she tried to restart the tractor it wont start. I checked it and got it running only buy a long cracking cycle with the throttle at max power. once its running it runs fine and no...

I have a few options available right now... I can get the L3430HST with LA723 FEL, R4 tires for just under $20,000 Or A used L4310 HST new around 1998, 700 hours, R4 tires, FEL (1998 version of the LA853) Asking $17,900 I haven't negotiated anything yet so that $17,900 price is just the...

I found a 1999 L4310HST with FEL, 430 hours on it. and the guy tells me to make an offer on it... what is a fair price on one of these? It looks to be in really good shape..

I am going to look at a 2000 L4310 FWD with 523 hours on it this saturday. The tractor has a L681 FEL and also a backhoe Does anyone know what the engine and PTO HP is on this and also what the lifting capacity of the FEL is. The backhoe make and transmission type are unknown at this time but...

Just called about a 2001 L4310 HST with FEL. It only has 133 hours. With a "bush hog" the guy is asking $18500. It belonged to his late father in law. Totally new to the Kubota line. What should I look for/ask about. Do want to add a BH. Barry

Hey guys I'm new here and need some advice from your experience. I'm looking at two tractors for family and business use a '03 L4310GST with 125hrs and a '01 L3710GST with 760 hrs. The 3710 has a FEL but the 4310 doesn't and that is something we definately want. We've been given a price of...

I'm a first time tractor buyer. I saw an ad for a 2001 Kubota L4310HST hydrostatic 4x4 Loader with 500hours for $3300. Can anyone comment on whether this is a good deal and what questions I should ask the person selling it? Thank you!

Post deleted by Travis_R

The Glow plug light on the dash stays on after the engine is started. Have not checked if the glow plugs are actually getting voltage but suspect that they are. I've been just turning the key on and off until the light stays off and then start. But it's getting worse and more frequent. I...

The 3Pt lift is stuck in the full up position regardless of lever position. Took a quick look and the lever seems to be attached to rod coming out of the top of the case in the rear. Does anyone have any suggestions? Rich

Hey guys. I was b'hogging my property today with my L4310, and after two hours, I could no longer raise or lower the mower. The hydraulic fluid quantity is OK, and I've got 200 hrs on the filters. That's also the total time on the tractor, a 2000. It has been stored all winter. There were no...

Am thinking of buying a 3PH mount woods 7500 for the L4310. My uses are trenching for drainage and cleaning up stone rows - burying the stones. I use 3pt mounted implements so need to have use of the 3pt hitch. Price is $5500. Sure wish I could find a used one. I hate paying retail. Anyone have...

It is time for my 50 hour fluid changes. My local Kubota dealer who assured me they had all the correct parts information and fluids, had only some Agco brand transmission and engine oil. They said it was as good as the recommended Kubota oils. They also sold me the filters. I returned 2 (...

A friend bought a new L4310 last year with several extras - but his circumstances now require that he sell it. What would be a fair asking price for L4310 GST with 225 hours, 4wd, R4's, FEL w/60" hd bucket, Curtis heated cab, Woods 9000 subframe backhoe, 6' rotary cutter, front forks, front...

I hve been given a pric of $31798 including tax for the following package: L4310HST w/R4 tires Kubota Front Loader Remote HYD Outlets York 6ft Poly Broom for Loader Rhino LT6 Brush cutter RAD 3pt Debris Blower Used 3pt auger used 3pt post driver This is my first tractor purchase. This sounds...

My original posting appears to be in error. While at the dealer, I found out that their 2000 L4310 HST was actually a 1998! The tractor has 4wd, factory cab, R4 wheels, and a loader with under 200 hours on it - all in very good condition for $21,600. A local farmer has a 1997 L4200 GST with...

Hi, I am looking at a 2000 4310 HST with FEL, R4 tires, and a factory cab with 200 hours from my dealer for $21,600. Does this seem to be a good price? Thanks

I need a favor from the Kubota forum! I have a buddy looking to buy a L4310 or L4610 with a FEL and hydrostat transmission, are there any good/bad/otherwise comments that I can forward to him? I would greatly appreciate it!

Anybody out there find a soft cab for the Grand L3710/4310 that they can vouch for? I've seen the generic 1 size fits all but have my doubts. Snow season is approaching, and a cab sure would be nice. I'd love to have Kubota's hard cab but I cannot justify the price. <P ID="edit"><FONT...

Though I find it troubling to feel any joy in our current state of affairs, I can't hold this in any longer. I've been trying to wait till I signed on hte dotted line but..... After years of wanting, it seems I'm finally going to get me a tractor. I found this site a few months back. after...

Hello all, my first post - I have been lurking for some time but am finally taking the plunge by registering and posting. That said, my appologies since this is a very mundane and common type question. I searched previous posts first. but alas,, I found a dream tractor last week not 5 miles from...

I wanted to thank all those who provided me information on purchasing a Kubota. After looking everything over, I decided to move up from a L3010 to a L3710 or L4310 to mow the acreage I own. I bought an L4310 with a new Landpride 6' rotary mower and new weights on the front. The tractor is one...

Ok, I have been lurking for some time. I seek advice from the gurus of tractors...so I came here first! I was all set to buy a L3010 for landscaping use. The dealer ordered it today!!!! It cost $17,400 with FEL (thanks for all the great posts) The problem: The dealer has a L4310 GST that was...

Kubota L4310 with 4:1 Bucket. Bucket was made by my local dealer. They did a great job.

L4310 with Gannon HD Box Blade. Notice the Gannon Hydraulic Top/Tilt/Scarifier contol mount on the fender.

L4310 Kubota with Woods 9000 Backhoe.

L4310\'s and very steep hills First of all, a few disclaimers (lest TomG, or others, rightfully chastise me for not being safety conscious ), in no particular order: Just because I do something on my tractor, don't assume that you should/can/etc. No matter how implausible this sounds when I...

Adv > L4310hst \"over stocked\" Adv > L4310hst "over stocked" on sale, must go now >> Steve@CarverEquipment.com

Some of you Tractorbynet forum "old-timers" may remember a few posts I made to the old board about "enhancements" to my L4310HST. Well, this is Chapter 3 (I think): Yesterday was a "work on the tractor" day. Nothing too major, but one thing in particular that I thought might be of general...

Re: buying new L4610 vs L4310 Thanks for all the input. I had to wonder about the R4 with mud, and I think Gordon must be right. I have never used them. Now MCalkley has got me wondering about these Michelin's.What ply rating are they? IM worried about STUMPS. I went to their web page but could...

Ok I tryed this once before be Im sure my comp ate my post?? Have a ford 1910 with loader and ag tires. Looking at L4610 or L4310 to up grade, need more HP. Read last post about loader's and had been leaning to L4610, now Im sold. So thats that. L4610 it is. I skid alot of wood ie. long logs...

\'<adv> 99 L4310hst/loader just in We are pleased to offer to you the following packaged deal. 1999 Kubota L4310HST diesel tractor, 4wd , 43 horsepower REALLY GREAT CONDITION with 337 hours Hydrostatic Transmission Standard non folding - 2 post ROPS R4 industrial style tires, with ballast...