Rear Blade Adding hydraulic angle to rear blade

[BIG DOOLEY]

This is my TSC rear blade I am adding hydraulic angle to.
I also want to point out that the tubing was holding water and a drain hole should be added to prevent rusting and damage to tube during cold weather due to expansion of ice.
I ordered a 3" x 12" 3000 psi cylinder from Surplus Center.
The 3" bore cylinder has a 1-1/4" shaft and will be less prone to damage if bumped in the woods.
12" stroke completes the same left to right angle as the factory holes.
I will wait to weld the front mounts until the cylinder arrives.
The blade can be rotated 180 deg. and the cylinder reattached on the opposite side for reverse blading.

Tom

 

[J_J]

Nice job so far, waiting on the video of a working model.

 

[BIG DOOLEY]

Added a bearing collar to maintain spacing needed for new control arm clearance.
Blade will be able to rotate when in the lowered position.

Tom

 

[Jose G]

that's a hellof a plate

 

[BIG DOOLEY]

1/2" x 3" plate.
Doubled where cylinder connects to add strength and remove slop in the tie-rod cylinder end.

Tom

 

[mjncad]

I like it! :thumbsup:

One minor suggestion...paint your parking stand yellow so it stands out from the rest of the implement. I forgot to raise mine, and this was the result. https://picasaweb.google.com/110106108324823291002/FrontDitch#5397037847269121218

Deere/Frontier/Woods wanted $40 for a replacement. I made three and had them powder coated yellow for about the same cost. I have two spares in case I screw up again.

Note to Muhammad (sp)...please put a modern pop-up photo gallery viewer on TBN! Thanks!

 

[kateean2]

so useful.hehe.thanks for your share.

 

[Herkypilot]

Nice job! I like fabricating steel to make something more useful.

 

[BIG DOOLEY]

Thanks all.

I like it! :thumbsup:
One minor suggestion...paint your parking stand yellow so it stands out from the rest of the implement. I forgot to raise mine, and this was the result. https://picasaweb.google.com/110106108324823291002/FrontDitch#5397037847269121218

Yes, yellow would be an excellent idea.:thumbsup:
I wasn't distracted

"I'm getting older and forgot to raise it"

I'm turning over a new leaf this year and just tell it how it is.:laughing:
I have taken off down the driveway and heard it scrape the cement.
Its easy to do especially with the quick hitch.
Now that there are hoses to hook up I might not forget or I will drag the hoses around too.

 

[kennyd]

Great job BD as usual!

If I may offer one suggestion when posting pics, please add a space in between them so they don't look they all run together.

 

[BIG DOOLEY]

Great job BD as usual!

If I may offer one suggestion when posting pics, please add a space in between them so they don't look they all run together.

Never tought of that.
Much easier to fabricate blindfolded that post a thread.
I'm learning in progress
Can do, I had a little trouble with that myself.
Thanks.

 

[devildog1]

Kudo's on a great job of fabricating the hyd angle of your rear blade, looks great .
DevilDog

 

[94BULLITT]

Nice work Tom.

 

[etcallhome]

Very Nice

 

[94BULLITT]

A hydraulic side link with float would work good with the power angle for snow removal.

 

[BIG DOOLEY]

Thanks guys.
My order from Surplus Center was picked today, shipped today?
Home with a bad cold the last couple of days.
I hope to feel well enough to go to work tomorrow.

 

[OrangeToys]

Just found a project for my blade!!!! Looks good

 

[MtnViewRanch]

Just found a project for my blade!!!! Looks good

For your 8' blade, I would think about using a 3 1/2" x 14" cylinder. If you look to see what the OEM guys use, I'm pretty sure that none of them use anything smaller than 3 1/2".dia cylinders. I know that Land Pride uses a 3 1/2" x 14" for your size of blade.

 

[OrangeToys]

For your 8' blade, I would think about using a 3 1/2" x 14" cylinder. If you look to see what the OEM guys use, I'm pretty sure that none of them use anything smaller than 3 1/2".dia cylinders. I know that Land Pride uses a 3 1/2" x 14" for your size of blade.

Thanks for the info Brain

 

[BIG DOOLEY]

I finished the fabrication on the blade.
The cylinder and hoses should arrive UPS tomorrow.

Tom