I broke it...first day with 2305

   / I broke it...first day with 2305 #21  
Well I have to say that I have gotten my 210 loader cocked up a couple of times. I think once on hard ground and once on soft ground. All in all I find it to be pretty easy to put on or take off. I also like the fact that there isn't some cheezy parking stand on the 210 loader. I haven't taken a good look at these new loaders, but that thin tubing would scare me. IIRC It's one of the (many) reasons I chose the 2210 over the BX22. I didn't like the single cylinder bucket curl, and the flimsy parking stand.
As for the hose connections, they will wear a little over time and become a bit easier to make or break. OTOH, if your loader is off, and the hoses have been sitting in th sun, pressure can build up in them and make it darn near impossible to re-connect. In this case you have to purge them to relieve the pressure. Do so by wrapping a shop towel over theend of the hose and push the valve against something hard and immoveable. A paved surface or the mower deck or the loader arm will work.
 
   / I broke it...first day with 2305 #22  
Well I have to say that I have gotten my 210 loader cocked up a couple of times. I think once on hard ground and once on soft ground. All in all I find it to be pretty easy to put on or take off. I also like the fact that there isn't some cheezy parking stand on the 210 loader. I haven't taken a good look at these new loaders, but that thin tubing would scare me. IIRC It's one of the (many) reasons I chose the 2210 over the BX22. I didn't like the single cylinder bucket curl, and the flimsy parking stand.
As for the hose connections, they will wear a little over time and become a bit easier to make or break. OTOH, if your loader is off, and the hoses have been sitting in th sun, pressure can build up in them and make it darn near impossible to re-connect. In this case you have to purge them to relieve the pressure. Do so by wrapping a shop towel over theend of the hose and push the valve against something hard and immoveable. A paved surface or the mower deck or the loader arm will work.
 
   / I broke it...first day with 2305 #23  
Buckie
I only took my loader off once on unlelveled ground. I did have a hard time putting it back on. Now I always take it off 0n a slab of concrete. It takes me less than two minutes to take it off or put it on. I think you will get a lot better. I take mine off this time of year twice a week.
 
   / I broke it...first day with 2305 #24  
Buckie
I only took my loader off once on unlelveled ground. I did have a hard time putting it back on. Now I always take it off 0n a slab of concrete. It takes me less than two minutes to take it off or put it on. I think you will get a lot better. I take mine off this time of year twice a week.
 
   / I broke it...first day with 2305 #25  
Agreed. It got easier over time. I got myself a 3720 just recently and am very happy that taking the FEL off of this tractor, compared to the 2210, is a snap. Maybe JD heard us, after all!
 
   / I broke it...first day with 2305 #26  
Agreed. It got easier over time. I got myself a 3720 just recently and am very happy that taking the FEL off of this tractor, compared to the 2210, is a snap. Maybe JD heard us, after all!
 

Tractor & Equipment Auctions

72" HYD QUICK ATTACH GRAPPLE (A51406)
72" HYD QUICK...
2025 Kivel 48in Forks and Frame Skid Steer Attachment (A53421)
2025 Kivel 48in...
2016 Chevrolet Malibu Sedan (A55853)
2016 Chevrolet...
2023 New Holland CR10.90 Combine - 330 Engine Hours - 251 Separator Hours (A55314)
2023 New Holland...
CNH 60" QUICK ATTACH LOADER FORKS (A52706)
CNH 60" QUICK...
New/Unused 7ft Stainless Steel Work Bench with 20 Drawers (A54865)
New/Unused 7ft...
 
Top