New Tooth Bar
- Thread starter caddison
- Start date
- Views: 1607
OP
caddison
Gold Member
OP
caddison
Gold Member
OP
caddison
Gold Member
tinytractors
Bronze Member
- Joined
- Feb 14, 2005
- Messages
- 73
- Location
- VA southeastern
- Tractor
- Kubota L3430 HST, 52 Ford 8N, JD455 AWS, Bayou 300 ATV
Looks great... What type is it...?
Pete.
Pete.
OP
caddison
Gold Member
Pete,
I couldn't tell you manufacturer as I got it off of EBay very reasonable....one of the few deals I have gotten off there. It has the replaceable teeth and it is heavy duty.
I couldn't tell you manufacturer as I got it off of EBay very reasonable....one of the few deals I have gotten off there. It has the replaceable teeth and it is heavy duty.
frank_f15
Super Member, Rest in Peace
another convert to the toothbar hey? /forums/images/graemlins/grin.gif
OP
caddison
Gold Member
It is bolted. I used 1/2 bolts w/ some flat washers for spacer and some bushings to take up some excess room in the slot where the bolt went through.
OP
caddison
Gold Member
Frank,
I had been looking to get one and was about to order from Markham. I ws snooping about EBay one evening and came across this tooth bar....brand new w/ replaceable teeth. I thought there was no way this thing would go for the $150.00 it was posted for. I wound up getting it for $162.50 and there was only one other bidder....sometimes you get lucky!
I had been looking to get one and was about to order from Markham. I ws snooping about EBay one evening and came across this tooth bar....brand new w/ replaceable teeth. I thought there was no way this thing would go for the $150.00 it was posted for. I wound up getting it for $162.50 and there was only one other bidder....sometimes you get lucky!
bandit67
Veteran Member
- Joined
- May 27, 2004
- Messages
- 1,610
- Location
- Lake Hartwell, SC
- Tractor
- 2012 B3000 HSDCC 2020 Z251 Zero Turn
It looks just like my Markham (only bigger), so you may have gotten one from them after all. Seemed that when I was looking, all the different mfrs I looked at each had their own distinctive looking toothbars.
OP
caddison
Gold Member
Well that would be GREAT if it is!!!! I like it and am looking forward to some digging!
Kiohio
Platinum Member
It looks like a WR Long. Markham doesn't slot the end plates on their toothbars, unless they just started.
We have had both at the shop.
KO
We have had both at the shop.
KO
Dirtball
Silver Member
It's a New Holland skid loader bar. I have the same thing on my NH TC33 60in. bucket. It's 10X more toothbar than we have tractor. It's engineered for the 80hp 8000# skidloader to rip the crap out of things. Has allowed me to dig better and great for ripping out rootballs and holding onto branches during transport to the burn pile. I tack welded 8-10 washers to take up the slack on the ends. Only drawback is it wont fit over replaceble cutting edge-BUT I was told there is another tooth bar that does fit over .
OP
caddison
Gold Member
Hey Dirtball,
I'll give it one thing it is heavy duty. Mine fit over the factory edge of the bucket fine. I had to use 4 washers on the inside of both sides and then used some bushing to take up the space between the 1/2 inch bolt and the remaining space in the mounting flange. They must use some big !@# bolts to mount that thing on the skid steer. Anyway it was a bargain! Can't wait to tear up some dirt with it!!
I'll give it one thing it is heavy duty. Mine fit over the factory edge of the bucket fine. I had to use 4 washers on the inside of both sides and then used some bushing to take up the space between the 1/2 inch bolt and the remaining space in the mounting flange. They must use some big !@# bolts to mount that thing on the skid steer. Anyway it was a bargain! Can't wait to tear up some dirt with it!!
