Citydude
Super Member
Glad to be of assistance! Take care.
Pat's Easy Change Pat's Easy Change System - Order Online!
- Thread starter Muhammad
- Start date
- Views: 314277
Glad to be of assistance! Take care.
KevT
Platinum Member
- Joined
- Apr 1, 2015
- Messages
- 996
- Tractor
- Kubota L3901 HST w/ FEL, ST2046
I bought the Pats at ASI and it came complete with spacer bar. Now it is so easy to change attachments on my own, they are wonderful
KevT
Platinum Member
- Joined
- Apr 1, 2015
- Messages
- 996
- Tractor
- Kubota L3901 HST w/ FEL, ST2046
wrflt
Silver Member
Ok, I'm back. It's been a while since I installed the Pat's Easy Change but I only recently used my rotary cutter with it. I'm really liking the system as it does make changing implements much easier. Here's the deal tho; with the rotary cutter it seems the pto shaft on the cutter may be about to come loose. Where can I find an extension for the drive shaft and what would it be called. My thanks in advance.
KevT
Platinum Member
- Joined
- Apr 1, 2015
- Messages
- 996
- Tractor
- Kubota L3901 HST w/ FEL, ST2046
I had the same issue so this is what I just ordered. Pto Adapter The pic is wrong, but description is right. Haven't got it yet, will let you know when I do
gwdixon
Elite Member
Actually, I think the photo is correct. I own two of them. They work perfectly and make up for the longer PTO requirement that the Pat's causes.
KevT
Platinum Member
- Joined
- Apr 1, 2015
- Messages
- 996
- Tractor
- Kubota L3901 HST w/ FEL, ST2046
You have a better pic than I do because when I bring it up it shows a six spline to a 21 spline, but describes a 6 x 6
gwstang
Platinum Member
If you have a TSC (tractorsupplycompany) near you, they have the extensions that work.
wrflt
Silver Member
Yeah, thanks guys. The pic shown (6x21) is the same as the one I found at TSC, which won't work for me. I do need the 6 to 6. TSC didn't have that one. Now that I know there is such an animal I will ask them to order me one. Thanks again.
gwdixon
Elite Member
OK, my fault for not looking at the photo better. Indeed, it is not a 6x6 spline photo.
Calling AgriSupply, or waiting for the product, is a reasonable option.
Below is the bookmark that I have on my browser that I've used for ordering (appears to be the same one as listed above). The product was a 6x6 when it arrived.
Pto Adapter
I also tried to order one from Tractor Supply but they didn't have one in their online catalog. Maybe if one goes into the store in person then they can special order it.
Calling AgriSupply, or waiting for the product, is a reasonable option.
Below is the bookmark that I have on my browser that I've used for ordering (appears to be the same one as listed above). The product was a 6x6 when it arrived.
Pto Adapter
I also tried to order one from Tractor Supply but they didn't have one in their online catalog. Maybe if one goes into the store in person then they can special order it.
Poopdeck Pappy
Elite Member
- Joined
- May 13, 2013
- Messages
- 2,628
- Location
- Dallas, Texas
- Tractor
- Kioti DK50SE Cab, Kubota BX23, Kubota BX2660, Grasshopper 729BT
Poopdeck Pappy
Elite Member
- Joined
- May 13, 2013
- Messages
- 2,628
- Location
- Dallas, Texas
- Tractor
- Kioti DK50SE Cab, Kubota BX23, Kubota BX2660, Grasshopper 729BT
gwdixon
Elite Member
No, that is not it. Kubota PTOs don't have a hole in the tractor's shaft to drive a pin (or bolt) through. That is what the item in the Tractor Supply link requires for a Kubota. Don't know about other tractors' requirements.
The one in the other link has a pin to lock it on the tractor's PTO shaft just like most PTO implement shafts.
The adapter in the link in post #651 will work on tractors that have an indentation on the tractor's PTO shaft...which is almost all tractors.
Just got my easy change and first off my hydraulic top link was now too short. I fixed that by buying another top link from TSC and cutting and welding the ends together to make an extension. This works on the brush hog.
Next I left the stabilizer bar on while I was mowing and bent it pretty good. Don't remember reading anywhere where it said remove it after hooking up implement.
I have to mow some ditches and a dam that makes the mower deck move and flex. The PTO shaft bent the bar.
If you have a hydraulic top link it is a little expensive to just buy a longer one, not so much a manual top link.
I think it is a good idea but if you are considering purchasing one. Do your home work. It definitely is not plug and play.
Next I left the stabilizer bar on while I was mowing and bent it pretty good. Don't remember reading anywhere where it said remove it after hooking up implement.
I have to mow some ditches and a dam that makes the mower deck move and flex. The PTO shaft bent the bar.
If you have a hydraulic top link it is a little expensive to just buy a longer one, not so much a manual top link.
I think it is a good idea but if you are considering purchasing one. Do your home work. It definitely is not plug and play.
Mendonsy
Veteran Member
Yep!! If you have the PTO hooked up and raise the implement all the way it will bend the stabilizer bar.
I don't know casesam what you mean by the "Bent washer www.casesam.co.uk thingie"...:shocked:
Last edited:
Helitech
Silver Member
Loving mine! Ordered them and Brian at FitRite helped adjust my ordered hydraulic top link to account for them. These are the best money I've ever spent! 
fried1765
Super Star Member
- Joined
- Jan 6, 2015
- Messages
- 10,159
- Tractor
- Kubota L48 TLB, Ford 1920 FEL, 8N Ford, Gravely 12 HP "Professional", 48" SCAG Liberty
Loving mine! Ordered them and Brian at FitRite helped adjust my ordered hydraulic top link to account for them. These are the best money I've ever spent!
You might want to consider getting some shorter mounting bolts (they are 5/16" or 3/8" I think) that are grade 5.
The bolts included with the kit are grade 2 junk. They are also too long.
The included junk bolts will break off, or the threads will strip, likely leaving you with an extractor job.
Other than the bolts, the Pat's kit is absolutely great!
