While using my tractor my temp gauge was showing a normal running temperature, then suddenly showed a cold reading. My heater in the cab got cool. Full of antifreeze, no leaks, etc. Everything...

i recently bought a jd1070 which runs great. by fuel tank somehow get partially crushed. i’m looking for ideas to repair the tank i appreciate sound advice thank you very much!

This is a bit of a complicated post so I will try to summarize as quickly as possible. I have a a John Deere 1070 that has been sitting unused for 5+ years and am trying to get it going again. I...

Hey everyone, First time posting, and need a little help with at least some terminology/ parts so I can search better. There doesn't seem to be a lot of info about the 1070 and I think better...

I'm new to the tractor market but need something to do some work and maintenance on a property I bought and will be building a couple houses. My buddys neighbor has a 93 john deere 1070 that's...

I have a 1070 with very wide turf tires. I would like to swap out for narrow turf tire or R4 tires. There is a set locally from a John Deere 4066 in R4. Would these fit onto my 1070? as far as I...

I have a 1070 (bought it new the year they came out) with a disconnected wire under the dash. It has a female connector on it with 2 wires, appears to be yellow + blue, and a solid blue (or could...

Does anyone know where I could source a (preferably good, used) JD 1070 right side engine side panel/cover? Thanks.

I am changing oil in a JD 1070 for the first time for a relative. Can anyone tell me the recommended viscosity and capacity? I presume 15w-40 but want to be sure. Unfortunately, I don't have a...

Hi, I have a John Deere 1070 with Backhoe and front loader. It doesn't get used often as you can tell. Fired it up and it has a hydraulic oil leak in one of the front cylinders... i need to take...

Hello, I recently bought a JD 1070 (2WD, FEL, 8B backhoe, finish mower, box blade). Runs and drives strong, and I've enjoyed using the loader to clean up my small property. Unfortunately, I...

Anyone on here have a 70 series tractor 870-1070 that has a factory or have added a Creeper gear set up.

I ordered which i thought was the correct repair manual for my tractor which was JD TM1470. It says it covers the 670, 770, 790, 870, 970, and 1070. Turns out it only covers the 790 for engine...

Lonnnng story short.....just had the motor rebuilt with a new/used crank, new/used block, new bearings, seals, rings etc. Upon getting the tractor back, first time i start it up the low oil...

I'm trying to change the fuel filter (on engine) on my 1070. The manual says to remove the bowl, turn the top ring counter clockwise. Can't get it to budge. It looks to me like the ring should...

I was running my JD 1070 and the negative battery terminal popped loose. The tractor shut down. I put the negative cable back on and then the tractor would crank, but not start. If I manually pull...

I just used by 1070 2 days ago. Went out today and when turning the key on I hear a click and the dash lights come on but it won't do anything else. I crossed the terminals on the starter and it...

Guys I bought a John Deere 1070 just last week that has turf tires on it. It is a 4wd model with a loader bucket. I didn't realize I would have to get new wheels as well as the tires. The...

MY JD1070 seems to be plagued with fuel tank rust. (especially the filler neck and cap). My old cap had this issue and I replaced it not to long ago and look at the new one! The inside of the...

My JD 1070 is no longer starting. I have replaced the starter, battery, and the seat safety switch. A friend came to look at it today to see if he could figure it out and it started right away...

For the last 5 or 6 years, I've replaced 4 regulators. Alternator has been checked and confirmed good. Fan belt tension, fine. Last year, no light would come on until 2100 rpms without lights...

Just got scammed on 1070... lm going to need a lot of help... Thought it was a deal but now l think the clutch is bad. Takes off slow in low and mid gear and barely takes off at all in High...

Hi all, Does anyone have a CD of TM 1470 they'd be willing to share via a PDF or otherwise? (Sorry, not too techically savy with this) Email is vjwotz@aol.com. Just trying to keep my old 1070...

I went to refuel and noticed the inside of my fuel cap is all rusty/corroded. I thought diesel being oily would protect vs corrode. I don't get it. I replaced the cap but wonder what's going...

Hi everyone. I have a John Deere 1070 and am having a problem with the clutch or clutch pedal. The clutch pedal doesn't have any free travel in the up (foot off) position. When I depress the...

Wanted mid PTO & belly mower fo JD 1070 . I have been told that an 870 or 970 will fit also . The part #'s I have are BM17995 or am107214 I can be reached at 615-336-4069 anytime or email me...

I have a 1996 John Deere 1070 Tractor with a John Deere 440 loader. How do I remove it?

I have noticed the following going on with my JD 1070. MFWD and roughly 1500 hours. When the weather is cold out (below 40 F), when the tractor is started and initially put into gear upon...

I am looking for a ring and pinion part # AM 877504.A for a John Deere 1070 John Deere says you have to order and pay for it in advance and they have no idea when they might make it again Thanks Roy

Hello, First post here. I have a Deere 1070 and I was using it to mow with an 8' flail mower. I've used this mower for a number of years. I don't think the issue is because of the mower but...

I falled some large douglas fir trees down in a gulley. I'm just trying to estimate if it's too steep an incline/decline for my JD1070 4 wheel drive with loader/rear blade and filled tires...

I have a JD 1070 tractor with a non-functional tachometer. There is no needle present in the instrument cluster for the tachometer gauge. Both fuel gauge and temperature gauge work fine, as does...

I own 10 acres, about 4 of which is "lawn" about 4 of which is farmed by the neighbor, and about 2 of which has become a tangle of poplars, poison ivy, raspberries and other stuff I'm tired of...

I'm making plans and gathering materials to adapt a Boss V snowplow to my JD 1070. I'm going to remove the entire FEL, build a frame to adapt to the Boss carraige and, hopefully, use the tractor...

A friend of mine gave me the plow side of a year old Boss V-plow after it was involved in a minor accident. The damage is all in the center pin/pivot area. He kept the hydraulics and truck mount...

Hi all. I'm not really a new member, but I forgot my password and I'm kind of retracing my steps. I now use a Kindle Fire and it won't allow me to perform all functions I used to enjoy here. I'm...

The steering cylinder on my JD 1070 is leaking pretty badly. I have ordered new seals for both the cap (gland) as well as the piston. I suspect my leak is the seal between the gland and the body...

I have a JD 1070 and was mowing with a brush hog when the PTO locked up and killed the engine. There is nothing hung up in the mower. Where do I begin to troubleshoot this thing? Thanks!!

Hello, boys! I hope all is well with you. This seems like a really stupid question, but here it is. I have just acquired a John Deere 1070 that works well in every capacity. But I cannot find...

Any of you guys out there have a john deere 1070 with a MMM have on your tractor or sitting in a pile in the corner. Plates that look like this. It's the mid mount by the loader mount. If so...

I finally found a mower deck for a good price. And if anyone read my other pages I found the whole mounting kit new just 15 years old. For 100$ when I went to install it today the 1070 required...

How do I get the front cowling off to replace a Deere 1070 battery? Original battery from purchase (1997 model)

I was wondering if anyone knows about jd 72" mower decks. I recently found a belly mower hardware kit for 72 mower deck for $100. Will any of the john deere 72 decks work. I know it's compatible...

I bought a JD 1070 at auction a couple of weeks, seems like a decent tractor. Starts and runs great, but I am having 3 point hitch problems. After I bought the tractor I ran into the mechanic...

I looked at A 1070 tractor that is a 4X4 and has 4800 hours on it. It had Hyd for a loader and rear Hyd on it. . Were these a good tractor? The engine runs like a top and it looks like new as it...

I recently purchased my 1070 from an auction. When I loaded and chained everything down o came across this on the tractor. I didn't purchase any but tractor and the loader . Did I miss something...

My JD 1070 will generally start up OK and sometimes stays running good. Intermittently it will start and then 'die' after a few seconds and frequently not start or run normally unless left off...

When switching the ignition switch to 'off', from engine running, the engine continues to run for anything from 10-30 seconds. Any clues as to the cause and its repair? Any guidance appreciated...

I'm new to the owning a tractor but have ran big deere 81-83 series for a larger farm operation. I bought a compact for my acreage. After buying the machine from a auction with 1300 hours for a...

I am mainly posting this for google posterity in case anyone else ever runs into the situation and needs this part. On the JD 1070, there is a short stub axle/pinion that feed power from the rear...

Hello all, i just acquired at 98 1070 with the 440 loader. Machine has 887hrs, and for some reason the temp gauge will not move. Can someone please walk me thru diagnosing this. Im Trying to find...

Hi Folks, My first post here! Joined forum to see if I could get some help with my 2000 deere 1070 (39hp) tractor w/1100hrs... My current problem involves the tractor jerking (lurching?) when...

Looking at a 1993 Deere 1070 tractor 4x4 to replace my old Ferguson 35. The Ferguson 35 has a Davis 102 loader run off a front mount Cesna 20GPM pump. What are the chances the loader will fit...

I am having problems with my Hydraulics on my 1070. I recently made a trade for a non running 1070. After an engine rebuild and new injector pump, I have no hydraulics. The first mistake I made...

my jd 1070 sw 3amp fuse keeps blowing. what should i check?

I have bought a 1070 and it appears to have Hyd problems. The loader is slow and jerky when going up and the steering is also erratic. I am going to change the fluid and filters but I haven't...

I recently bought a '90 JD 1070 mfwd with a loader and 1,000 hours on it. After using it to backdrag an area for about 45 minutes my 4x4 disengaged and I was unable to get it to go back it. The...

John Deere Backhoe Mounting Bracket No connection, don't know if this is a deal or not, but I am sure someone here might could use it!

I've got a '92 JD 1070 4wd with a 4-n-1 bucket that I am thinking of selling. It has a hair over 1200 hours on it, and a canopy with a couple of cracks from getting a little too close to some low...

I dropped the keys in the snow and then inserted it in the ignition switch. I think the moisture shorted the switch. I can not get any electrical items to turn on. I am hoping JD has a fuse in the...

I jumped on the JD 1070 and started it and the clutch was stuck and would not release.The crew drives it most of the time and after picking up some new Bobcat units i don't run the JD 1070 much...

I am looking for the threaded section for my right lift arm on my Deere 1070 mine is bent

I've got a Deere 1070 w/MFWD, and I accidently high centered the tractor on a log and bent the FWD shaft. If I roll the shaft on a flat surface, it looks to be bent about 3/8". It seems to work...

I am wanting to wire two or three work lights on my JD 1070. I have done a few small home wiring projects, but haven't attempted any projects this ambitious on my tractor. Where do I start? Is...

Hi, I have a JD1070 with model 80 bucket/loader. On occasion my right leg accidently applies pressure to the SVC joystick and the bucket goes to the dump position. Is it as simple as reversing...

I was hoping that one of you could assist me with an electrical issue. I have a 1070 with an electrical problem. A few weeks ago, I tried to start it and nothing happened. Clicked but no...

Have a drive train issue I pulled the tractor up to the garage to change the blades on the mower and it started to rain so i pulled it up into the driveway. The next day my wife got on it to mow...

What is a good replacement seat for a 1070? I don't want to get another stock one cause frankly, it's uncomfortable. I feels as if I am being pitched forward all the time...not good for long...

I own a 1994 JD 1070 which has gremlins messing with the temperature gauge for at least the past ten years. It has been worked on by two different dealerships. There are still problems. It...

I currently have a John Deere 1070 with turf tires. I priced ag tires and rims last year and found them a bit too pricey. Finding used Ag tires with rims has proved fruitless. A dealer...

I need a swinging drawbar for a JD 1070. Any idea where to get one besides the JD parts store? I want to avoid paying $170 for one!

Hi all, Been lurking on here for a couple years but finally have a reason to post! We recently purchased a new home on 20 acres and I was able to work a deal on a couple new "toys". One of...

Got a buddy who wants to put a grapple on his 1070. I know Deere sells a rear remote kit I'm told is for a backhoe that is the same a PB but I'm wondering if the kit is even really needed as he...

Hey Guys, I need some help. My JD1070 is acting funny. I can't get it to go into gear. It almost acts like the clutch is still engaged even when I have the clutch peddle fully pressed down...

I purchased 6 month ago a YM2210 with FEL but did not go for a 4x4. I regret this deeply because I get constantly stuck on my property. I am looking into trading the Yanmar in and possibly get a...

I have a john deere 1070 and I am putting wetlines on it and I put a prince 2575 4 way valve on it and I think it has a nob under the seat to turn hydraulics off the the 3 pt lift arms I turned it...

has anyone replace a clutch on a Deere 1070. its a daul stage clutch. i have never replaced a daul clutch before. looking at the parts diagram on the deere web site, looks pretty complex. should i...

How hard would it be to put a hydraulic pump on my 1070 and where would be the best place to find a pump at ?

How hard would it be to put a hydraulic pump on my 1070 and where would be the best place to find a pump at ?

1992, has 1300 hours, JD 440 loader, looks from the pictures about 60" wide bucket. Owner says light use, $15,000. Of course he is trying to get is sold for max and I'm trying to get it bought...

I recently purchased a John Deere 1070 Compact tractor ( which is actually made by Yanmar ). My question for you fellow owners is this. There is a yellow "Oil" cap on the right front of the...

I have a chance to buy a 390 front blade for my 1070 4x4 and I was wondering if they are made strong enough to push more than snow,such as dirt and gravel or if they're pretty limited to snow. I...

I was operating on an asphalt road the other day when my 1070 started making a God aweful sound like the tranmission just blew up. I stopped the tractor and found I could still move. I drove the...

I'm new at the forum thing. I've been working on tractors and mowers all my life but can't find what I'm lookin for and haven't ever added remote hydraulics. I work for a golf course and we use a...

I'm new here. I'm going tomorrow to pick up my JD 1070. It's 4WD. I want to get a disc for food plots. How big of a disc will it handle? I see there's a King Kutter 5.5' unit for sale down...

I'm considering purchasing a used 1989 John Deere 1070. Comes with Big Bee bushhog. Has 4WD. With 2500hrs. What would be a good current market price? Owner asking $9000. Doesn't sound bad...

I needed to use my 1070 to dig out some snow drifts this past week and at <20 degrees she barely started. It turned over a couple times then tick-tick-tick. My second attempt got it started put...

:rolleyes: I have a 1990 JD 1070 with a couple electrical problems. Both are when you first turn the key one, there are two clicks, one for the starter and one louder one for the fuel solinoid. I...

I noticed a spark on the right side (sitting on the seat) of my tractor when I started her last. I had a friend start it so I could actually see where the spark was. It came from a rusted bolt...

Good Morning All! I've been on the forum before, but haven't posted. I own a John Deere 1070 which I really enjoy and I am glad to see other 1070 owners out there. Yesterday, brush hogging, I...

i think i may have run it out of gas but the fuel filter tanks were both full i was not getting fuel to the injector heads i opened up the lines on top of the pump and adjusted them i have fuel at...

It is getting extremely more and more difficult for me to get parts for my 1985 JD 750. These days I am hearing more of "no longer available". I know this is a Yanmar product as is the above...

I went to the barn yesterday and pulled out my JD1070 and noticed where it was parked had a large dark oily spot. It turns out I have a pinhole leak in my fuel tank. I can put a toothpick in the...

I have been leaning toward a new L3400 for all the reasons you buy new, but see a clean NH 1920 (800 hours) and a JD 1070 w/Curtis Cab in the 12,500-13,000 range on dealer's lots. Primary use is...

Anyone invest in the publications for their machines? I have the operators manual, but looking into the parts catalog and tech service manual. Is is worth it? Anyone own the CD's?

Hello out there. I am thinking of buying a 1997 JD 1070. Low hours - under 100. Comes with loader and backhoe (neither used), and roto tiller. Any thoughts on what this rig is selling for these days?

Hello out there. I am thinking of buying a 1997 JD 1070. Low hours - under 100. Comes with loader and backhoe (neither used), and roto tiller. Any thoughts on what this rig is selling for these days?

I thank those of you who replied to my request for info on the '96 4x4 JD 1070 for $13,500. Today a friend told me that his uncle had a 5103 that is only a couple of years old and has less than...

I've been looking at used tractors in the 40-55 HP range and ran across a '96 JD 1070 4WD with FEL and 840 hrs for $13,500. I know the reputation of JD and everyone that I know who owns one...

I've been looking at used tractors in the 40-55HP range and ran across a '96 JD 1070 4WD with FEL and 840 hrs. for $13,500. I know the reputation of JD and every one that I know who owns one...

buyjd-ML-880850-ML- JD Buying Question

Well, I think I am finally ready to make the jump. I have been toying with it for some time. I am looking at a 1998 4wd 1070 with a 440 bucket loader and a 8b backhoe w/ 500 hrs. I have managed to...

I'm looking at buying a used JD1070. Could someone please tell me what the engine hp is as well as the GPM of the hydraulics? Thanks everyone

My JD manual says that either weight can be used for my 4X4 tractor given the temperature range it operates. Is there any advantage of one over the other? Does anyone know what weight is used...

My JD 1070 is approaching 10 years old but it only has 49 hrs. on the clock. The JD manual calls for a hydraulic fluid change every 400 hrs. That'll be another 70 years!!! Is there a time...

I am looking for some feedback on the 1070 model.I am looking at one to purchase and wondering what you think. It only has 270 hrs on it,4cyl diesel,seems like a nice tractor.

Ran across a used 1999 JD 1070 4wd w/ FEL, 90 hrs, guy is asking $16,000 for it. Is this a good price. Is there somewhere I can find specs on the tractor. Thanks !