finish nail puller deluxe.

[Hay Dude]

I use blue handled nail nippers and just pull. If I have to bend the nail, the curved jaw face usually doesn’t damage, but if it’s real delicate, I just pin a wood shim under them to protect wood surface. They are a must have in my tool pouch. They come in different sizes.

 

[WranglerX]

This has always been my tool of choice IF I needed a nail extractor....

The Extractor Extracting Pliers Review - Fine Homebuilding

The Extractor Extracting Pliers

www.finehomebuilding.com

Dale

 

[DaveinValdez]

Taught Wood Shop for 25 years. I always taught to kids to pull the finish nails through to lessen damage on the good face of the board. Used vice grips, the rounded edge and put a thin scrap piece in between. Almost always worked great.

 

[PILOON]

" Almost always worked great."
Cautious optimism?
or
alternate facts?

LOL, It gave me a good chuckle.

 

[DaveinValdez]

" Almost always worked great."
Cautious optimism?
or
alternate facts?

LOL, It gave me a good chuckle.

I always considered it good teaching year if i kept the stiches under 12. Managed the entire career maintaining the ability to count to ten! 🖐🖐 Retirement is great!

 

[Hay Dude]

Only problem with pulling finish nails through the back is if you have a piece of window/door trim mostly nailed on. Then you have to pull it out the way it went in. Usually a grasp and a twist and it’s out....kinda like a wisdom tooth. Lol

 

[MossRoad]

Only problem with pulling finish nails through the back is if you have a piece of window/door trim mostly nailed on. Then you have to pull it out the way it went in. Usually a grasp and a twist and it’s out....kinda like a wisdom tooth. Lol

Oooo I've done that a few times. Just a couple nails left in the trim and WHACK!

I've learned over the years I'm more awesome on the demolition crew.

 

[downsizingnow48]

This is a bit off topic. There were a few times when I wanted to save a piece of trim with an out-dated profile. The alternative might be to spend a few hundred dollars at a local mill for them to grind a matching set of knives and make some new material.

But mostly it does not make sense to pay someone to pull nails so you can put back up a (usually) cracked and (always) paint chipped old piece of wood that is worth about $2.00. Throw away the old stuff and put up new, you will be money and time and quality ahead.

 

[lennyzx11]

This is a bit off topic. There were a few times when I wanted to save a piece of trim with an out-dated profile. The alternative might be to spend a few hundred dollars at a local mill for them to grind a matching set of knives and make some new material.

But mostly it does not make sense to pay someone to pull nails so you can put back up a (usually) cracked and (always) paint chipped old piece of wood that is worth about $2.00. Throw away the old stuff and put up new, you will be money and time and quality ahead.

Even farther off topic.
I usually just cut the nails off on the back side with a pair of side cutters or my cordless angle grinder with a cutoff wheel on it for a whole bunch.
The little stick out (1/8” approximately) works good to “tack” the piece in place holding it while the real nails get driven.

Pulling them through seems to crack the older dry trim for me so I cut them off and leave the head buried in the wood under the original filler done long ago.

To remove the trim, I use a paint scraper/putty knife jabbed down to protect the wall as a backer and a set of thin 90degree trim bars to get started. Like these.
Pry Bar Set (3-Piece)

Dasco Pro Pry Bar Set (3-Piece) 91 - The Home Depot

Visit the Home Depot to buy Dasco Pro 3-Piece Pry Bar Set 91

www.homedepot.com

 

[Scar0B2150]

We had oak floors in our house. They were "sanded" to refinish them very poorly, before we bought the house. So I ripped them all up and installed a new bamboo floor.
Now to the point. There were several boards that were still in decent shape that I figured would be good for some projects. But there were several 100 nails still in the boards.
So I came up with this.
A cable tie clamp that you screw into a wall to hold phone lines, a small nut, and a rivet gun.
Worked like a charm! No tear out on either side.

Coffee table made from the flooring.

I also made a dining room butterfly table out of it.