TractorTech
Elite Member
- Joined
- Jan 26, 2012
- Messages
- 2,845
- Location
- California
- Tractor
- Ford 7710, Ford 550, Ford 1910, Ford 4430, KD Forklift, Ford LGT17H, New Holland L255 Skidsteer
My mistake, TD75DA..Delphi
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser.
You should upgrade or use an alternative browser.
Injection pump install
- Thread starter Dwilliams4wranch
- Start date
- Views: 3645
pmsmechanic
Elite Member
- Joined
- Dec 6, 2013
- Messages
- 4,226
- Location
- Southern Alberta, Canada
- Tractor
- 4410 and F-935 John Deere, MF 245
Yup 3rd paragraph. I could have stated it clearer though.Great methodology, but if the pump, Bosch, has been taken out, the pump will have to be retimed by the injection shop first.
OP
Dwilliams4wranch
New member
- Joined
- Oct 4, 2022
- Messages
- 8
- Tractor
- New Holland td75da
yesR we talking about a TN75da.??
OP
Dwilliams4wranch
New member
- Joined
- Oct 4, 2022
- Messages
- 8
- Tractor
- New Holland td75da
Sorry been traveling since first post. I did talk to local dealer in my area and his first question was did mech. mark the timing before he removed the pump (answer is no). Dealer stated it was going to be difficult to get right as they had one similar and they spent 100 hrs on it (hard for me to believe). There is a mark on flywheel that coincides with TDC, mech bought special tool to retime pump still would not fire, we did check it does fire useing a gas rag.
So if I pull pump have it retimed and have #1 at TDC that should be it? If not what has to happen? Do as PMSmechanic stated?
TIA
So if I pull pump have it retimed and have #1 at TDC that should be it? If not what has to happen? Do as PMSmechanic stated?
TIA
thepumpguysc
Elite Member
That wasn’t meant for u D..
Just my sarcasm shining thru..
Just my sarcasm shining thru..
thepumpguysc
Elite Member
Before u pull the pump again.. Snap a picture of the front of the engine.. inside where the pump bolts up..
I might get the same result if u can answer this question..
Inside the engine where the pump bolts to the gear.. is it 1 nut and washer or 3 bolts holding the pump to the gear..
I sure hope u answer 3 bolts.!!
I might get the same result if u can answer this question..
Inside the engine where the pump bolts to the gear.. is it 1 nut and washer or 3 bolts holding the pump to the gear..
I sure hope u answer 3 bolts.!!
thepumpguysc
Elite Member
I’m in the middle of several pump o/h’s so give me time to get back to you..
OP
Dwilliams4wranch
New member
- Joined
- Oct 4, 2022
- Messages
- 8
- Tractor
- New Holland td75da
npI’m in the middle of several pump o/h’s so give me time to get back to you..
OP
Dwilliams4wranch
New member
- Joined
- Oct 4, 2022
- Messages
- 8
- Tractor
- New Holland td75da
bad news 1 nut and washerBefore u pull the pump again.. Snap a picture of the front of the engine.. inside where the pump bolts up..
I might get the same result if u can answer this question..
Inside the engine where the pump bolts to the gear.. is it 1 nut and washer or 3 bolts holding the pump to the gear..
I sure hope u answer 3 bolts.!!
Harry in Ky
Veteran Member
So is this guy still working on it, or have you moved on from there?