Search results

Ok, I'll get new lines made up. I just didn't know if there was such thing has a patch or clamp or something. Thanks all.

I may just go this route. Remove the line, have a new one made. While I'm there, have them splice in a new line at the pin hole on the old line. I'll have a new line in, and have a spare. I was just shooting for a quick clamp or something using a sleeve and some ubolts or something.

Follow up question on those reusable hoses, what am I using to cut the existing hose? Straight up angle grinder?

If it leaks and does not work, the seller refunds the money and alters the review to their specifications. XD

Those splices, so cut the line before and after the pinhole, then put those ends in then. That may be an option too.

Ah, good point. Yea, this is a hose. Flexes and stuff.

Ah, that's sort of the thing I had in mind. For $150, I'll replace the entire line. Just the one time the issue is right there, easy access, in plain sight view that I was hoping for a fix.

Woods9000 on my L3710. There's a pinhole leak on one of the lines. Its one of the longest lines on the setup too. No idea how the pinhole got there, but its away from all mounting surfaces, bends, couplings, or anything. Right on the "straightaway" on the line. Easy access, right there. Is...

The plug that connects to the unit from the rocker switch had a wire corrode off. While plowing the driveway, I angled the plow, and it pitched on way and got stuck "on". At the time, I thought the rocker switch on the joystick went bad and was stuck. Took a hot minute with the leatherman to...

Welp. Life of a rust belt mechanic,

I've done all I can to remove that spool. Since I already snapped to pins, I went deeper. I've put two notches into the plastic and used a gear puller to remove it. Won't budge at all. I'm actually tearing the plastic up and off.

https://store.wrlonginc.com/products/valve-solenoid-12gpm-valsold03s How does one remove that? Like anything else, a quick swap turned into a $100, one week wait. Thanks.

well that's a relief. just have to wait for the other parts to come in. should be a quick fix from here.

Yep. Ordered two of them. I looked for 20m for the parts breakdown, made this post, and the very next thing I learned was it was the FEL parts list, not the tractor. Found it shortly after. Also order a proper bolt extractor set. Just sucks because I have always used the welder to get a...

So I punch all that in, and right after I find that its the FEL, not exactly the tractor I need to look for. LA6841. I have this setup, https://www.(Temporarily blocked due to reports of company closure)/3rd-Function-Hydraulic-Kit-p/tra-3rd-funcl.htm and can't recall if that came with a new lever or not. I'll have to...

2000 or 2001 L3710. I'm not exactly sure what to call these parts to be able to do a proper search: control valve lever? the lever that maneuvers the bucket. as you can see, that heim joint broke off. and something tells me I'm not going to be successful getting that broken bit out of...

huh. good question. something I had not considered. either one would work though. I've got a manual thumb on the back if need be.

Brush guard is on. Calcium in tires. Woods9000 slung on back. I have a localish guy that makes grapples. He's going to try to do something up for me. Only its a single cylinder instead of a twin. But its all 3/8 and 3/16" wall. Looks good.

So I emailed the local place about a Land's Pride one. There's another one that was suggested here, and they're out of stock. I do see a bunch of places locally that have some. Now, are these all the Chinese garbage ones? I feel like they are. For instance, I used a weld on thumb from Titan...

Just messaged Travis. 4 to 5 months out on your 55" grapple huh? damn.

EA is "We’re 4-5ish months or so behind." on that grapple. crap. right in line what I'm looking for too. DOM and AR plate. There are others I'm seeing, but are 3/16" and Sched 80. Don't need anything wide. <60" would be totally fine, but I want/need something stout. I can't help but feel...

cool beans. I had no idea that's how that worked.

No kidding. So a LA681 is 1362 kilos or pounds? kilos seems up there.

Good stuff. I'm actually going to call EA today on the EA 55" Wicked Root Rake Grapple. See what the story is there. Apparently a backlog.

Can't find what my lift capacity is. I think I need to lookup what loader I have- I forget. LAsomething. I attribute Sched with "poop pipe" so I may be wrong with that way of thought. 820# seems a bit heavy, but the guy that I've chatted with says 260# which almost seems too light.

In need of a grapple on the front of the tractor. Equipped with a skid steer quick attach. I'm thinking something along the lines of 60"-66". Smaller size. What's the weight limit I should be looking for? Local place has a 62" that's 820#. Guy on a forum I frequent builds a single ram, 60" one...

yea know, I thought so. no, its not the light. I had the dash apart yesterday and that was one of the things I tested; I switched the lights around and it kicked on.

2001 L3710 If I put the key onto the run position, not start, the little light on the dash doesn't kick on to "preheat" the glow plugs. I swear that light always kicked on at least briefly. It was in the upper 30s the other day, and nothing. Tractor did take a little bit to crank to get it...

Alright, so I went and started draining. Got about 5 gallons out. There's the sight glass. I can see it registering now. Stopped what I was doing. Going to let is settle for a bit then go from there. Man, where'd this ten gallons come from? I hit both rear hubs and the center one along with...

Got the fluid changed. Question on capacity. Says 10.3 gallons. I pulled both rear drive plugs and the one dead center. Got about 5 gallons out. Started filling. I'm up to 9.5 gallons so far. And stupid me, didn't notice the sight glass in the back. I can't tell if the fluid level isn't...

Yea, L3710HST is the hydrostatic like I have. I done derped on that. NAPA had the filters. Be here tomorrow.

Going to go ahead and change the hydraulic fluid in my L3710. Tractors and hydraulics aren't quite my forte. There a go-to place for filters and stuff? Like a SummitRacing, only for tractors? I punch in the filters into Amazon and I get filters compatible with an L3710DT model; not sure with...

I'm smack in the middle of a drainage project in the backyard. Got a 100' trench dug 2.5' deep. Laying 1 1/2" stone, fabric, more stone, 4" perforated PVC (green stuff), and finally more stone all the way to the surface. Going to leave the stone exposed. The dirt from the trench I need to move...

Looking to add a thumb to my L3710. Prefer hydraulic, but a manual one is fine. I've got a Hobart 180 220v welder on mixed gas, so I'm fine with welding. The Woods9000 backhoe runs off its own hydraulics from the rear PTO. Where would I be tying into to get the thumb going? I'm going to have...

Heyas. Got an L3710 with a plow setup. Used Everything Attachment's third function kit. Works great, minus one caveat. The fittings by the plow side are incredibly hard to engage. I pull back the collar and insert the male into the female, and I have to use all my strength to get them to click...

There. That should hold. That square tube is 3/8". I ran out of argon mix towards the end though. Its all mounted to the tractor. Hoping this holds up. You have any idea how hard it was loading this up over the tailgate into my F250? haha

Not my greatest welds. But I took it home and it lines up just fine on the tractor. Now to bring it back to the shop after work today and plate the whole thing.

Hey there. I have a Kubota L3710 currently with a Kasco Uni-Hitch setup. Its garbage. Utter. Garbage. I've fixed it a few times, but short of welding 1" thick steel plating to the entire unit it, it keep twisting on me; especially when attaching the plow. The latch dogs have also always given me...

That time of year again. Our driveway is a quarter mile long with a somewhat steep hill at the end. I've got an 8' plow on the front and a Woods9000 backhoe on the rear of my L3710. As of right now, the driveway is a sheet of ice. My F250 with studs barely makes it up. Wife's car, don't even...

Machine is a 2001 Kubota L3710. I swap between a FEL to bring in firewood, and a plow setup from a truck for snow removal. Running a Kasco Uni-Hitch setup. Its awful. I can't stand it. Came with the tractor when we bought a few years ago. If I had one attachment that stayed on, it'd be fine. But...

I'll update this in case someone else has an issue in the future. Here's the part that broke: Friend of mine welded a piece of threaded rod on it. See how it works when I get home tonight. Kasco did get back to me, and this setup is discontinued. "Thank you for your email. The part...

Is it possible to get parts for this? A pin sheared off that locks the attachment in place. The cube like parts near the top. The bolt porting sheared off. This part; sorta. The above pictures belong to Titan and I doubt they would work. I can't find a parts diagram for Kasco Uni-Hitch...

Greetings all. I have a question about plumbing a front snow plow on the front of my L3710. Here's the tractor: I bought an 8' Fisher snowplow that has two hydraulic rams for angle. The plow is connected to a skid steer style quick connect plate. I plan on using the mid mount PTO to drive the...