Search results

Att is down in Warren County missouri. 50 mike's west of St. Louis

Ouch! I probably paid maybe $100, but it was in the mid 80s. That certainly changes the equation.

Rent a commercial duty model and be done with it. 35 years ago I broke up a driveway. Rented a pneumatic jackhammer with big town behind compressor. Done in 90 minutes and back to the rental yard. I do have a Bosch SDS these days for small stuff though.

I've got a Raptor 54" zero turn abd they say 8-12 psi. I'm heavy, so run 10 psi.

F150 Powerboost 21mpg Subaru forester 29.8 Toyota Avalon hybrid 39

I would remove, clean, and reattach the cables to the battery and starter first. When it doesn't start, does the solenoid try to make the connection?

Do any of the electric trimmers take a steel blade? I like a blade for weeds as it cuts rather than shredding.

I've not used these, but fragnible BBs are not supposed to bounce off of hard targets. Air Venturi Dust Devil Mk2 Frangible BB Bullets, BB Gun Ammo, 1,500-Count https://a.co/d/bCCBPQf

Angle grinder & flap wheel works great

What suspension seat do you have? I'm. Looking at some, but they've only got one inch of travel.

I've got them on my Hustler as well. Not a "Boulevard Ride", but better than stock.

I have a 4100 and you pull up on the switch to use the pto while off the seat. Does yours not work the same way?

I think those are the same blades used on my bosch jigsaw

I buy similar to this Retail Pack Flexible Replacement Gas Spout with 2 Screw Collar Caps(1 Fine & 1 Coarse - Fits Most Of The Cans), 2 Base Caps, 1 Stopper Cap and 1 Stainless Steel Filter/Flame Arrestor. Amazon.com: Retail Pack Flexible Replacement Gas Spout with 2 Screw Collar Caps(1 Fine &...

I've got one sold and sized for picking up brass at the range. Works fine on concrete. Not so good on grass or gravel.

Last letters of my call is GOM. I've found some Europeans have trouble with Golf Oscar Mike, so I switched to Germany Ontario Mexico.

I also have one. Used it a week or so ago.

I use an angle grinder with 80 to 120 grit wheels.

Would make a great gag gift.

About like that. I guess I just need the right sized screwdriver to pry the spring clip up or off. Does the clip stay attached? Or does it fly off into the weeds never to be seen again?

I'll try and get one in the morning.

My zero turn has a "snubber cylinder" attached to each control lever so they kind of stay in place and don't move on their own. On one side the attachment unscrewed from the rod. I need to screw it back together, maybe with loctite, but don't know how to pop the plastic piece off the ball to do...

Current companion is a Mini Aussie. 43 pounds of love and attention.

I have the same model one year newer. There is a switch under the seat. Fold the seat forward and pull up on the switch.

That's where I bought my 15Kw propane unit in 2003. Delivered right to the door and installed during construction of the house.

Low manifold pressure.

Doesn't she notice the blank adaptor on the muzzle?

Was it a passing zone?

I'm hoping I don't need to go look for my 4100 manuals, and I won't if anyone can provide the required torque for the wheel bolts. I figure someone has all that stuff at the tip of their fingers. Thanks in advance.

Here's the fox keeping my squirrel population under control.

Like most of us I have some painting projects around. Doors, door frames, picture frames etc. Nothing big like the side of a barn although painting walls in the house is a possibility. I've been looking at the Wagner HVLP sprayers that are self contained and plug into AC. They have a built in...

I may have asked this last year, but don't remember any answers if I did! I buy RoundUp concentrate and mix according to label directions. 2.5 Oz per gallon in a 2 gallon pump sprayer that's used for nothing else. Now I usually don't use all I mix for a particular spray session so some often...

I stopped by a place in town to get the phone number of a fellow who's done some pruning for me in the past and saw this machine. The fellw asked me if I knew what it was and I said "Sure, it's a Power Trac". He replied that I was the only one who ever knew what it was. It's 13 years old and...

Well, summer is coming and with that comes dry weather and dusty gravel roads. I'd like to spread Calcium Chloride on our subdivision road and am looking for some advice. I have a JD4100 and access to a borrowed cone spreader. I've reads that calcium chloride can be spread as either a 35% more...

I use RoundUp, the real stuff, in a 2 Gal. pump sprayer to keep my gravel drive clean. I also use it to spray around obstructions such as light posts etc. I mix according to the listed directions. I often don't use up all that I've mixed, so leave it in the sprayer. Sometimes a half gallon or a...

There's a two wire socket at the rear of the frame that's not connected to anything. It's got no power with the light switch in the OFF position No power with the flashers ON 12V with the headlights ON No power with the headlights and flashers ON I've going to use it to power a rear facing LED...

I guess I need to drop a few pounds. I discovered that the seat brackets on my JD 4100 tractor were broken! Had to buy and install a new seat. Easy job, only on cotter pin to pull and replace. Guess I need to skip a few lunches and dinners.

I have a JD4100 that's about 5 1/2 years old. I guess it's a 2003 maybe. It's the last year of production. I'm considering purchase of an electric sprayer to mount on the 3PH. Any idea were I can tap off the power to run the pump on the sprayer? I think they are diaphragm pumps and don't draw...

Saturday morning one of the local teen drivers missed the curve and wiped out our subdivision sign. :( No one was hurt, so that's OK. His folks say they'll pay for a new sign. The old sign was made by one of the residents. It was a glued up panel with purchased wooden letters applied. The...

I found these pictures on a non-tractor website and do not remember seeing them here. They are recent, last month according to the date, and are quite dramatic. The story given is that he was trundling down the road towing a trailer when the FEL dropped and dug into the road surface bringing...

Anyone have any ideas on what it might cost to add hydraulic outlets on the rear of my 4100? I'd like to be able to add/use a top and tilt on the 3PH. I'm thinking maybe outlets at the rear with QD and maybe a push button on the existing joystick so the control for my loader could divert power...

Anyone see this last night? I recorded it but haven't had a chance to view it yet. Was it worth watching? :confused:

I've got a MD floodlight, two heads, mounted between my garage doors. This is the second one in two years. They work fine for a while, then get erratic in their operation. They don't work when it's been raining and it's damp. Or they don't work when it's really cold. Two brands, both from the...

Here's the deal. I have a JD4100 and am looking for a seat with some springs or other type of suspension. My tractor, with R4s, rides really hard. My ground isn't too smooth and I'll admit to not lowering my tire pressure when mowing vs. using my loader. I had lowered the pressure and then went...

Anyone watch this show last night? Several examples of unsafe practices shown at the potato farm. The owner had Mike driving a Bobcat. The top was cut off. No roll protection. No safety bar. And finally, the owner operating the Bobcat while standing on the seat. I'd expect this guy will be...

OK, there have been many posts in the past about coating the underside of mower decks, as well as coating FEL buckets. Various products such as SlipPlate and others have been discussed. This product, Duracoat, was developed for and is marketed as a coating for firearms. It's sprayed on and can...

Had the chance this weekend to use a borrowed PHD with a 12" auger on my JD4100. Thanks to all the safety postings here, and those in the Attachments Forum, I knew enough to keep everyone away and operate it in a safe manner. Also knew to keep raising the auger to clear the hole and keep it...

How is the length of a top link specified? Is it the shortest length or perhaps middle length? The toplink that came with my JD4100 is too long for the rear blade that I received as a freebe. It's too long to get the rotaion axis vertical. So as a result the blade doesn't stay level as it's...

I have one of the forced air kerosine heaters. You know, the kind with the blower and pump to atomize the fuel. Looks like a horizontal cylinder above a flat fuel tank. Can I burn off road diesel in this thing? I haven't used it in a while, but might like to use it some this week end. I don't...

Pat\'s Easy Change I got to install and use my Easy Change adaptors today. They installed easily and work even better. I no longer have to try and drag the implements around to get the ball ends over the pins. They work as advertised! Changing from the cutter to the box blade just got a whole...

Many years ago when I installed my garage door opener, I ran Romex across the finished ceiling surface and installed an outlet box to plug in the opener cord. Now I know it wasn't up to code, but has worked fine for 30 years. But we are planning to sell soon, so I know I need to make some...

Have any TBNers driven the new pickups with the four wheel steering? The ad on TV showing how the rear wheel steering helps back the trailer into a tight spot looks good. Also the part where he backs around the figure 8. I probably wouldn't buy based on that alone. But if I were looking at two...

Has anyone had any experience with the Modine Hot-Dawg heaters? http://hot-dawg.modine.com/ They are somewhat reasonable, $560 for 70K BTU, and are supposed to be good for garages and such. When the new home is built I'm having propane piped to the garage and am looking for a heater.

I'm planning to install a 70' radio tower on my property in the spring. It's guyed with Kevlar guys anchored with Earth Anchors (or augers if you prefer) just like those used for anchoring mobile homes. The ones I'll be using are 8 inch diameter and 48" long. They should be installed with the...

I just purchased an Woods CETB-530 toothbar from my JD dealer. Here's a photo of it mounted on my 410 loader. Went on nice. Drilled 3/4 holes in the bucket with a set of Unibits. Easier than I expected. Planning on trying it out tomorrow. Cost was $290.

I have a 2001 JD4100 and am having trouble keeping the tilt adjustment tight on the 3PH. It has the turnbuckle barrel and at the bottom there's nut with a piece of rod welded across one of the flats. I adjust the tilt so the 413 cutter is level from side to side. then tighten the nut against...

I have a 4100 and am wondering why it does not need/have glow plugs. Last fall before I bought the JD I borrowed a NH of similar size and it did have glow plugs. Just wondering why the difference. The folks I know with diesel trucks all have glow plugs. No complaints, just looking for an...

Having a new JD4100 with FEL, and not wanting to pay JD $200 for their metal box, a different solution was needed. I had read several posts about making your own weight and thought that there were excellant ideas. Here's my version: A Rubbermaid 22 Gal. storage tub, some 7/8 steel rod and some...