front

Hello, I am looking to confirm that my tractor front wheels are correctly aligned because I have only recently noticed that the inside wheel, when turning a circle, is turned into the circle quite a bit more than the outside wheel. The tractor is only used on grass and drives straight ahead...

I just replaced both seals on the front wheel hubs on my SA424 after 7 years and only 200 hrs. I use the tractor mostly for the hydraulics lifting stuff that I can't otherwise, the biggest job has been shifting dead Ash trees around my property for disposal (neighbor's outdoor furnace). I also...

Hello I am having a terrible time getting the front draft rod back in place. It came right off so what am I doing wrong that I can't get it back into the correct hole or the other side in the groove??

I have a 1030 Massey 4wheel drive and I have been looking for a front rim for this. There’s a lot of rims out there but I ain’t seen any that look like the one off my tractor. Anybody who can help point me in the right direction to find one. I greatly appreciate everyone’s help.

On my Kubota L3830, the battery is behind the headlights. To get to it you have to raise the hood. I'd like to put heavy duty 12 volt terminals on the outside, in front of the grill. It would make it much easier to jump-start the tractor, or to power a 12v transfer pump to fuel up. Maybe some...

Looking for pictures, videos or any good instruction on how to install a summit 3rd function for my Kubota B2620. The instructions it came with lacking good 'how to'. Any help will apprecaite very much. Jorge

Good evening I have a yanmar 186D and I wish it had front pto for a snow blower. I've been trying to find if there is aftermarket parts that can be acquired to make this happen ? Due to physical limitations I'm unable to look behind my tractor to blow snow. I would appreciate any input...

I have a TC24D. The left front wheel will not freely rotate when cold. Just wondering if anyone else had this issue, of course there is snow and ice under the wheel and it just slides. I checked the fluid level in the axle and my past experience is that when the axle is warm the wheel runs free...

Good morning everybody. It's been a couple of months. So I was wondering if MF makes front ballast weights for my 1825E MF? I noticed that when I apply some weight on the 3 point hitch...the front of the tractor comes off the ground (a little bit) if I need more traction with the 4X4...

What are the odds? The left front tire where you drain the front axel fluid, I noticed a fluid leak. Brownish colored on the snow. Tractor hadn't moved in a few days. The day before there was nothing on the ground. Well ok, must be a seal under the housing. Next day there was a lot bigger spot...

My JD4600’s front axle is leaking through the seals on the point where the driveshaft comes in and also at the ends of hubs (wheels). My local tractor mechanic indicated that the seals need to be replaced (the tractor is 25 years old) and had been leaking a bit in the past from those areas...

Hello new to the group and tractors . I purchased a MF1240 4 wd with a 1346 bucket with a couple problems. The front portion of the frame is broken on both sides I’m going to remove it and have it welded but it seems weak for what it’s doing any recommendations. I also need to replace rear tire/...

I have the OFS EKO 8 front chains. My front tire size is 10-16.5, OFA uses the same chains for this size and also 12-16.5. Unlike the rears I can't find any instructions indicated these should be modified for the 10-16.5 tires. However, I have tried to run them as is without success. 2...

Does anyone know what attachment bolts onto the front bumper on either side of the receiver and the bolt pattern? (see below) I tried M12 and M14 course bolts in the holes, but they didn't fit. The M14 tried to start but didn't thread in. It may be fine-treaded, but I haven't checked yet.

Crazy!!!! I broke some teeth on my front axle ring and pinion ring and sourced replacements from salvage yard in Canada years ago they sent one and the gear grooves swoop the wrong way I sent it back thinking they sent the wrong part. I revisited it again earlier this year and talked to a nice...

Tractor has the OEM three counter weights but it wants to "push" when turning sharp with the brush hog, maybe fill the tires would help?

Odd left hand front wheel intermittent lock up on my '21 GC1723EB, about 575 hrs, and could benefit from some advice. Only really happens in cold weather after sitting overnight. If I fire up and if I work if forward and back for a few minutes it eventually let's go and works normally. No noise...

For me it's the Bosch 18V Vacuum!. Hands down! Sure, I use the shovel and the poker, but cleaning up after using those is a must. Someday, I may change my mind and say "A handy fire extinguisher", but so far ,,,no! ;-)

Howdy all. I am trying to bring a YM186 back to life and I am in need of a front rim. It is the 5 x 12 two piece rim. If you have one and would be willing to sell it, please reach out to me.

Just a heads up. Don't know if this has been covered. Needed a front wiper blade for my 1742. Dealer said comes with arm only at around $116.00. Lady gave me a Napa number 6-016-A. Exact fit, under $20.00.

Hi All, my 2015 BX25D needed the seals replaced on the vertical stub shaft where the final drive connects. I also figured I'd replace the bearings and final drive seals since I would have it all apart and the BX has a little over 800 hours on it. There's a pretty good Utube video that shows how...

Ok excuse my ignorance, but I know most tractors with a FEL have some toe in with the front wheels to offset weight or heavy loads. However, looking at my front end, it looks like the left hand side(drivers side) is leaning way more than the right. Is this normal? How does one go about fixing...

This question has probably been asked before, so I apologize in advance for any redundancy. I recently sold my old tractor and now have a new 2024 YT359C. I’ve installed the radio and some other accessories, and I’m considering adding a camera at the back and one at the front for loader work...

Ive got a new to me 2008 branson 2910i and am going to do a hyd fluid & filter change but not sure what to use in the front axle. Do it take the same fluid or do you use gear oil? Would like to find an owners manual but no luck so far.

I have a Kubota l3130 DT with loaded R4s. With a set of Everything Attachments forks on the front and no implements on the rear does anyone know the Weight ditribution by %? I need to load it on my trailer with a log spltter near the tongue and can't get the tractor as far forward as usual. The...

I have a front tire on my Kubota MX5400 leaking. Any recommendations on tire sealants thanks

I’m headed over the mountain to the nearest dealer tomorrow to have RimGuard put in the rear tires. Since the trip to the dealer is a 3-hr drive one way: Would it make sense to have them RimGuard the front wheels while I’m there. My tractor is a TYM T233, which is a bit bigger than a JD 1025.

Every day I check in and click on New posts. It seems now that nothing posted in Front Porch show up to me when I click New posts. I have to leave New posts and go to Front porch to see them.

I have machines of each type and quad steer is awesome compared to the others. My main complaint with articulating is when your going along a trench or ditch edge it’s steers you into the ditch before steering you out. You have to very gradually steer out of it. Front steers problem is when...

I have a tire driven Sidewinder three point hitch rotary cutter. There is no front guard on it and it throws debris on the back of my tractor, up on top of the deck, and me when mowing grass. I want to put a guard on it but am conflicted about how close to the bottom of the cutter to go. I'm...

I have a Kubota 2380 leaking all the hydraulic oil from a spot near the front axle, circled in red on my picture. I'm trying to find what this part is called and how I can repair it. I'm looking in the manual and on forums/youtube and cant find anything yet.

on my 2706e I had the all purpose tire still AG looking but it said the all purpose on it … I ordered the AG of that size both tires are the same size … they are bigger is this a concerne for the front rear diff ratio ?

I have a JD3720 tractor and am not sure what to do. Then problem tire is an R-4 8ply 27X8.50-15 NHS bought in 2010 and 1300 hours on it. No fluid in the tire. I rolled the front tire half off, removed it from tractor, wire brushed the rusty beads, took it to a tire dealer and had it...

I have a ford 1700 tractor that i want to install a front loader on. Picked up a 1710 parts tractor for the loader. I beleive i have everything i need for the front loader , i just need to figure out where to tie in the main supply and return lines on the 1700. Do i need an adapter to hook up...

Have a BX25 with 500 hrs. I get a clunking sound from the front axle. Hard to say if it's from from changing directions or turning or a combo of the two. Fluid seems to be full in the axle. Or could it have to do with the 4WD? Just thought of that and not sure I've taken it out of 4WD to see if...

Has anyone performed work on their front axle / 4x4 system on a Massey 1652 or similar? (Should be same as 1547, 1648, 1652, 1749, etc...). I've got about 1500 hrs on my 1652. Great machine, no previous issues. During some heavy loader work recently, I've developed an issue with my 4x4. I...

I am looking for the part of the service manual that details replacing the valve controller.

Trying to locate a good front axle for a yanmar ym240

I have a Landpride 2072 shredder and the rubber front guards are ripping off. I've looked at Chains and they are close to $300. Rubber replacements are $25. Has anyone used anything different that is more durable than the 1/4 inch or 3/8 inch whatever it is or should I just go ahead and rebuy...

Looking for LA351 front end loader attachment for my Kubota B2400.

Anyone have a wiring diagram for the cab power for lights and radio. Lights stopped working and then couple days later radio stopped working. Check fuses and all are good.

Hello, Upsizing farm tractor tire size, and desired tires don’t conform with factory front/rear ratio. Going from 11.2-24 fronts (43.5” tall) and 15.5-38 rears (62”) with size ratio of .70, to 13.6-24 (47.6”) and 18.4-34 (65.1”) which is a front/rear ratio of .73. I remember Tony Jacobs...

My 2017 xg3025hd front axel requires 80w90 gl4 gear oil but i keep finding gl 5. What is the differance and can i use gl 5?

Anybody know where I can purchase the large U Bolt on the Farmall Super A front axle? Thanks

I need some help diagnosing a recurrent issue with my front final end drive on my MFWD T4.75. The sun (part # 5191412) & planetary gears (5165273) housed in the hub locked up somehow resulting in the planetaries loosing some teeth and the sun gear ground completely smooth. The Hub (87542225) was...

Hi, new to the forum, apologies if this question has been dealt with before. I inherited a Cub Cadet 7200 that's in very good shape overall and I intend to use it very lightly. I noticed that the front right wheel is leaking fluid so I'm assuming that it is probably a seal. I can't find the part...

Will both machines come out of 4wd ? Both are basically same HP I think. I think I’ve got one of my ZD1511 sold & wanting a 4wd for steep banks. I don’t necessarily like the front deck running on the ground because I have rough farm Ground. Regens are no issue as I mow 3-6hrs at a...

Hi folks, I have a 14 year old 800hr BX1860 on which I've just discovered the propeller shaft front joint cover (aka dust boot) (item 20 below) has worn through and fallen off. Interestingly, the damaged boot was just sitting atop the MMM deck which I had pulled off for springtime blade...

Hello Everyone - Can someone send me a couple pictures of the front sub frame on a 955 that a snow blower or broom would attach to? Any help which pictures / instruction would be great. Thanks Scott

I just wanted to say my Yanmar SB60R snowblower, attached to my Yanmar 425 performed like a champ this winter. I live in Montana and we had a light winter compaired to most years but when it snowed. it was in feet and usually multiple. The blizzard of January 17, 2024 I plowed 4 1/2 miles, 3...

Good day, I decided to change the oil on the front differential. Followed the instructions in owners manual. Seemed pretty straight forward. Does it take a while for the oil to make it over to the opposite side of the fill plug? I was told that when filling with new oil, unplug drain on opposite...

I was pushing a tree with my New Holland workmaster 75 hp which has 550LU loader. Some how the quick attach on right side came of and now would not fully retract about 5 inches on right side. Please help.

Greetings, I am looking to get a Front-end loader kit for 1978 MF 230 2WD Diesel Tractor. I live in Washington State.

For most of the time that I have owned my 8N the front grille has been out of alignment with the body and has not been able to close/lock properly. I bought it in 1996 and at some point in the early years of ownership my foot slipped off the clutch after stopping while still in gear and ran into...

Hi all. I just got bad news from my local dealer. Somehow almost all the gears and bearings on my front differential as destroyed. I don't how or why but suspicious on a 72" front blower and subframe that was sold to me by a dealer. I've had it about 4 years now and every year when I install...

I have a 12 year old L5740 running the original R4's. I just got a flat on a front tire while plowing snow, and the tire came off the rim while I was moving up to a spot where I could park without blocking my own access. This tire has 2 patches already and I'm guessing one failed. I am...

The manual says: KUBOTA SUPER UDT-2 SAE 80-SAE 90 gear oil Why specify 2 options? From what I've read it ships with UDT. Recommendations? I'm looking at buying the AMSOIL SEVERE GEAR® 80W-90 100% Synthetic Gear Lube for it.

I bought a front loader (used) for my Zetor 7245. I am trying to understand how it functions as the system is not straightforward. There are four valves, three of one type and a fourth that's different, that I would like to understand what they are for. I drew a (crude) schematics based on...

I have a B7800 that has been leaking hydraulic fluid from the front axle. I had it in to the dealer a few times, and it is still leaking. The first visit was a seal replacement, and it leaked within a day or two or getting it home. They took it back and put a 'speedy sleeve's in, and it...

Tractor 2016 XG3025 362 trouble free hours . I saw a little axle oil on the inside of my left front rim , for most of the winter it's been setting . i looked under the front end for a vent tube didn't see none , went and check manual there's none only vent the axle has is the blue threaded cap...

Any reason I need them. Do I need them to install chains? Buying rear spacers to make it less tippy Thanks

Hi folks, my husband and I bought 25 acres in a snowbelt in Nova Scotia, Canada. Our driveway is gravel, a bit of a switchback up the mountain, 1000ft long and climbs about 100-120ft in elevation. I'll be doing all the snow removal, because I work from home and my husband leaves the house at 4...