kubota bx2350

I am enjoying my new Kubota, although we haven't had any rain for quite some time, so not much mowing to be done. I am not there yet, but getting closer to the 50 hr service. I don't want to open a can of worms here, but would just like to know how many people use the Kubota brand motor oil...

My wife and I had our new BX2350 delivered last weekend (it had 2hrs showing on it). We got it with a FEL, 60" MMM, and a Box Blade. I am curious how *loud* the hydraulic whine should be when raising the box blade? It seems *quite* loud to me and though it lessons considerably after raising...

My new BX2350 with 60" MMM, Loader, and Grass Catcher was delivered yesterday. I took the loader off and mowed the lawn and it did a geat job. But when I went to put the loader back on, I had problems attaching the hydraulic lines. I was not able to connect the yellow and white lines because...

Wanted to share a great 50 hour service experience on my BX2350 at Pinnacleview Equipment in Walpole,NH. I've read some unhappy stories on list about dealers, so thought I'd share one about service done right. My BX is an early '06, and while I didn't have any problem I wanted to get the...

I am shopping for a new tractor and have been looking at a BX2350. I have about 1.5 acres of lawn and the tractor will be used mainly for mowing, but I may want to add attachments in the future such as a Frontend Loader. I am looking for a well built machine that will last for many years. I...

Hey guys, gals great forum! I'm a new member and a proud new owner of 2350 which I traded in a brand new factory replacement Cub Cadet 6284 end of last season. It's equipt with FEL and 60" MMM. Two questions I have is how come these don't have a fuel water separator? And just curious what RPM...

BX2350 Work Capacity? How much heavy duty type work is the bx2350 capable of doing with a FEL, etc.? Looking at one for our farm to do the lawn mowing, manure clearing from the small stables, rototilling, move feed bags and loose feed, snow removal/plowing, and running small bush hog type...

How fast do your rear implements or mmm settle on your BX tractors? With about 35 hours onmy BX2350, I notice that the mmm (after lifting to the transport position) will settle enough to start banging against the lift stops in about 60 seconds. The rear implements settle at least 1" within 3...

I am still shopping for a new tractor. I have found a leftover new '06 BX2350 at a really good price. Are there any substantial differences between the '06 and '08 models? I have looked at an '08 2350 and was wondering if there have been any major changes in the last two years.

I've been searching for a used 4' box blade for quite some time but there just doesn't seem to be any out there. Now I've come across a pretty good deal on a 5' King Kutter (full size yellow type) that I'm considering. I'm planning to use it for some actual earth moving chores with our...

This is my first post on this forum, although I have been lurking here for quite a while. I am getting ready to purchase my first sub-compact and am looking at the BX1850 and the BX2350. I need to be able to pull a small (12") single-bottom moldboard plow. My question is, will the 1850 with...

I have been the one person mowing for the past, Oh fifteen years, but today my lovely wife wanted to mow. I was conflicted -- frees up time for me to do other projects, but also introduces her to the wonder of tractordom. Visions of waiting for tractor time ran through my head. In the end I...

I purchased a new BX 2350 a couple months ago and it now has 27.3 hrs on it. It's back in the shop for the second time. First time was a freaky mmm belt break. Not a biggie but I have never heard of a belt breaking on these machines, The dealer and the Rep think it was simply a defecive belt...

Hi all, my BX2350 turns 2 years old next month and before the warranty runs out I wanted to get the fender reinforcement done at the dealer. No cracks in my fenders, so do folks know if I should get: A: The Step stay kit: BX2350 part number K2581-9554-0 (fenders are not cracked) B: Fender Kit...

BX2350 with 80 hrs dies at unexpected times. It seems to happen more when in low and mowing. It seems almost like a kill switch. The motor just turns off. It will immediately restart. Sometimes it will go for 30-45 mins before it happens again. Sometimes almost immediately. At one point...

Ok, I am in a conundrum and looking for input. I just sent this message to Messick for input, but I will solicit input here too: I have been on the forum for a few months now, and after much thinking, I think I am ready to make a tractor purchase. I was going back and forth between a ZTR and...

I'm trying to decide between these two tractors the Kubota is 11,250 the Deere is 11,900 both prices are with 60" mower decks. Have these models been around long enough to have all of the bugs worked out? Also tell me your likes about these models.

Anyone have any pics of the repaired or factory updates to this problem? I have a new (07) , but don't know exactly what to look for to verify if was updated. Maybe a pic of original, after repair, and factory update? I don't see much extra under mine, but not sure what I am looking for. Thanks...

hey gang!, leave it to me to think about asking for the impossible. on 12/31/07 i got kubota financing for a new bx1850 w/54" f/c deck, hd60" blade and i consumated the deal with my dealer. i am to finalize with the additional purchase of the fel prior to delivery, later this week . . . but...

Just left the dealer in central Iowa with the following pricing: BX2350 front weights: 1. 55lb suitcase weights - $60/EA 2. Bracket - $88 3. Bolt sets (1 per weight) - $6/EA Rear wheel weights: 1. Plastic, 53lbs each - $32/EA plus freight 2. Bolt sets (1 per wheel) - $6/EA This is quoted...

BX2350 less then a year old with 40 light use hours, always stored inside. Excellent condition with 60" mid-mount mower and front end loader. Just serviced with full warranty & manuals any drawbacks to used--I have seen it it looks quite clean and has been updated with al the latest service...

Took the tractor out and warmed it up driving it about a mile. Backed it into the garage and sat idling for about 1/2 minute and shut it off. Looked under back and had a puddle 3" wide and 6" long. Maybe an ounce of oil. Had this happen before. Appears to be coming out the pressure relief or...

local place has a bx2350 60" mmm right at 100 hours looks better than the ones which have been sitting outside. deck only small scratch or two. new loader for $10200.00 still has warranty until late 2009. any thoughts?

i have read til i am about sick it seems about these tractors. i am looking at one with about 100 hours at a local dealer. i have used a older one a little at a neighbors but not over a hour or two. my question is how will one of these do in the garden with a disc and plow? i know a tiller but i...

We're really struggling with this one. I'm not positive about the choice being Kubota, and the issue of this thread is really about buying with a BH or not, so I put it in this forum rather than the Kubota section. I'm wondering if I will use the BH much past this first year when I get a...

Need suggestions for where to take electrical power from for ROPS mounted lights on a BX2350. I've seen mention of a wire under the seat on BX tractors but couldn't find it. Is it there and if so where? Which fuse is it on? Is it possible to use one of the open spaces in the fuse box? Other...

Here's my BX2350 issue list as of today (tractor has 21.7 hours): 1. 2.3 hours - Dealer didn't top off hydraulic fluid after installing loader. Couldn't even see fluid in dipstick hole. Fluid sample was nasty. Took several weeks to resolve with Kubota. Ended up with free 50 hour service and...

Hi there, I've been following the forum for some time, and have found the advice and commentary to be excellent, this is my first post however. I will be in the market for a subcompact in the next few months, and thought that I had made my mind up on my choice of tractor (2305) - that is until...

Hey guys I am the proud new owner of a '07 BX2350 with front blower. Now I am looking into a hard cab. Looked at all of them online and find the Jodale_Perry and Laurin the be the closest to factory looking around. My question is does anyone have a Laurin cab since the model change and if so...

Hi, Does anyone have a BX2350 shop manual that would be willing to post or e-mail me the hydraulic section? I have the BX24 manual and wish to compare the sections. I want to install the factory remote valve but the catalog states it does not fit. I want to know exactly why. Thanks, Dave...

I had a BX22, and am now comparing my experience with that tractor to others that I'm looking at. The Kubota web site says that the overall width of the new BX series is 32.? something inches. That seems narrower than I remember. Could someone check out the width to the outside of the rear tires...

Oops! I got a server error when I tried to post this, and ended up with a double post..... sorry

I have a 1.5 yr old BX2350 (less than 25 hours) with front mount snowblower. Took it out this evening to clear the 850 ft driveway. The tractor repeatedly stalled when the PTO engaged to drive the snowblower but only when going downhill??? When going uphill there was no problem. After the...

I was wondering what it would cost and how hard it is to add remote outlets out the rear of the 2350? I would like to run a log splitter and a small backhoe attachment.

Hi. I have found a company who sell the BX2350 here in Sweden. Tell me if I wrong but isnt (speaking about naked tractor) the BX2350 and BX24 the same machine? In that case I can get spares/service parts for my BX24 here instead of ordering from US (which i really like:D ). Saves me alot of...

Fellas, I'm yet another newbie who found TBN while looking for info on SCUTs. We'll soon be proud owners of 4 acres (1/2 of it pasture, other 1/2 yard) in NC, and I've narrowed my tractor search -for MMM mowing, FELing, and garden tilling- to the JD2305, MF GC2300 and the Kubota BX2350. I've...

I saw a list of updates to look out for on the BX2350 somewhere on this forum but can't seem to find it again. I am aware of the replacement seat and fender reinforcement but it seems like there was a list of 6 to 8 things to check on before accepting the tractor. I would appreciate any...

I am waiting to get my new BX2350 and I am looking at adding a 3ph receiver hitch. Does the BX2350 have the standard 26" Cat 1 setup or the 20" Cat 1N?

After much churning and information gathering I took the plunge today and ordered a BX2350 with turf tires, the FEL and 3PH Farm King 500Y 50" snowblower for the business. I looked at the Massey 2300 series and the JD 2305 as well. The Kubota just seemed like a better tractor for my purpose...

One headlight just went out on my BX2350. I was quoted $17+ for a replacement bulb! Could this be right for one little bulb? Anyone have any reliable and reasonable parts suppliers they've used? Thanks.

Getting ready to pull the trigger on a BX2350 with FEL. I am also considering a rear blade to move snow. Anyone know the price for the 60" 3pt rear blade from Kubota or other third party options? Thanks in advance for the help!

For the first time today, I moved my PTO lever from mid+rear to just mid... I was blowing leaves instead of bagging... Once I was done, I had a heck of time getting the lever back to mid+rear to finish the job with a quick mow/bag... Any thoughts on the difficulty or tricks to help, when she...

I own an aircraft sales company and move small piston aircraft around my facility often. I am looking for a 4WD hydro tractor to accomplish this task along with a snowblower attachment as I live in Minnesota. I have looked at the JD 2305 and Kubota new tractors. I have also looked at used but...

I'd like to add another cylinder to my BX... Either for the 3pt and / or a cylinder for turning my plow when mounted to my front bucket... Anyone done this? Thanks Phil

I have searched and have read all the pros and cons of using a Three Point Log Splitter in general. I was wondering if anyone with a BX2350 (or similar tractor) has a Three Point Splitter. If so, what brand/style splitter? What is your setup? Do you have it plumbed to the Loader valve, if so...

Last I checked, my radiator is full, but the overflow tank is completely empty. I would like to add a little antifreeze, but I do not want to add the wrong type. The manual specifies long life antifreeze, but I am not sure what type to buy. Any suggestions on brand/type and the proper mix? I...

:D Ordered new BX2350 with Kubota LA243 Loader (48" bucket), Kubota 60" MMM, and Woods GTC52-2 Tiller for $14,250 (50hr service included in purchase price) taxes extra. :) Thanks to this forum, I also specified all updates to be installed prior to delivery. Kentucky dealer agreed and I will pick...

Repalcing a B7100 with 1600 hours. Have looked at the BX2350 & B7510. Will be using for mowing approx 4 acres which is mostly sloping land and some snow removal. Land being mowed has trees and rocks (boulders) to mow around and exposed rocks that I mow over sometimes nipping the tops if I...

I have a 2000 BX2200 with 500 hours on it, 60" mmm and FEL. Trading to BX2350 comparably equipped. Dealer has done all the service on the BX2200 so he knows it has been well taken care of. He's saying $7200 for the trade. I'm thinking that's a bit high. Any thoughts? Thanks!

I just started looking for a sub-cut and my 1st stop was at a Kubota dealer today. I'm planning on looking at other makes over the next few weeks too. I was given a price of of $13,500 for a BX2350 w/ FEL and 60" Belly Mower. The BX24 without the mower was just under $16K. These prices don't...

I just found a "never used" Lienbach 7300 PHD for sale by owner. My gut reaction is that it is too big for my BX2350. I have the QuickHitch, which does give higher lift, but, I'm still wondering if it is even worth trying to think it has a chance of fitting? Any thoughts?

First post but have been lurking for some time now. I am the proud owner of this tractor w/ FEL and have a question. My model # is Bx2350D. Does anyone know what version (with or without the mentioned services bulletins) my tractor is. Of course the dealer said all repairs came from Kubota but...

As a lurker on this forum for a number of years I finally made the jump to a Kubota BX2350. A lot of you have taken the time to share your experiences and I'm sure I have profited from your wisdom and mistakes. I have been working a 2+ acre lot with a small Toro riding mower but future...

Got the 2350 about a year ago, and as winter approaches I been debating on what type of snow removal equipment to purchase. I live in CT and do not get that much snow nor is the season long enough to warrant the cost of a snow blower attachment. I have been looking at front and rear blades. I...

Well, got a chance to put the new toy to work on Saturday on our lot on Lake Lewisville. But first, a little history... I had a guy clear out the underbrush with a skid steer last year to remove all the dead trees, and noxious undergrowth. He did a fine job, and allowed much needed sunlight...

Just ordered front and rear Bro-Tek skid plates for my incoming tractor. Anyone care to suggest any other add-ons for a newbie? All suggestions/advice appreciated.

Just had my 50 hr service done on bx2350; temp gauge constantly reads between normal and hot; not in the red but between half-way and red. dealer said problem was that the sensor was picking up temps from the exhaust pipe. I know others have had problems with the temp gauge not reading right...

Hello, I'm new to the forum and could use some advice. I purchased a new Kubota BX2350 (23 HP) and I would like to add a tooth bar to make digging in compacted earth piles easier. I see that the Markham tooth bars are highly recommended on this forum. Does anyone out there have a tooth bar on...

From looking at the pics in the manual - best guess it is underneath the platform? As I started my 50hr service - changed the fuel filter in the engine compartment, changed the engine oil/filter - without removing MMM... front axle to follow.... I have to remove the MMM (and bagger) for tranny...

Ok, I bought my tractor while in AR/MO.. now am in IL, so my original dealer is too far away to maintain my tractor.. Reluctantly, I called the local dealer, asked for service and explained my situation with him citing all the part numbers for the upgraded items including the PIB for the new...

Finally finished the plumbing and electrical on the new grapple. I used the 2x6 FieldMate cylinder from Surplus Center This One as well as the Solonoid Selector Valve This Valve. Besides the actual grapple mechanism, the rest is plumbing and electrical. The BX2350 is quite compact, so, dealing...

Two weeks ago I changed the front axle oil, and something's been bugging me. The manual calls for a capacity of 5 quarts, and mine only took 4 quarts to fill. Now, I did everything by the book, including breathers, both drains, waiting and then checking again, etc. I even tried manually turning...

In April I took delivery of a new BX2350. Love it! Except when stopping in reverse. Take your foot off the hydro drive slow, fast, or anything in between and you feel like you hit a tree. Whiplash. The only time it seems better is with a slow release of the pedal while going downhill (backing...

I know this topic has been beat to death - I have read several threads top to bottom full of tips/tricks - I am feeling very confident but have one remaining question that I am sure many may laugh at...but I have to ask... When replacing the fuel filter - the only tip I have seen is to duct...

Just had my local dealer put together a kit for the 50 hour service so I could do it myself. Even though the owner's manual does not list the fuel filters as something that needs to be checked or replaced at 50 hours, the parts guy insisted I buy 2 fuel filters and that I must change them out...

I noticed my grass was being cut lower on one side, so I thought I would try to level the deck .... simple adjustment, Ha! With the blades pointing front to back when measured for a 2 1/2 inch height, I can get the discharge side level but the left side front is higher by a 1/4 to 1/2 inch...

Hi, I am new here and was wondering if anyone that has a Kubota BX2350 can give me there first hand information about how much the FEL for this model can lift. I have 3acres (2 yard, 1 horses ring) and I am looking for a tractor that is small enough to handle the mowing but can also help with...

Grapple planning stages here. I have been doing searches and pouring over all that has been written about remote hydraulics. If I build a grapple, of course, I'll need to pipe from the BX's system to a control valve, and then on to the grapple cylinder. Here is what I think I know about it...

I wanted to give everyone here a big thumbs up for the great advice. I started out looking for a better lawn tractor to upgrade my cheepo Craftsman. When I saw the John Deeres and Home Depot, I started thinking about what a small tractor might do for me. I started looking at the NH Boomers, JD...

I have been looking at 5' Rakes and Carryalls for my Tractor. Howse and King Kutter manufacture both. Any suggestions or advice?

I just finished and used my forks on my BX2350 FEL. Soicne the BX2350 is on the small side of things, I wanted to keep the forks shorter, yet allowing for picking up things up to about the 500 lb. range. I used 2x2 square tube, 3/16" thick. They were 4 foot sections, but I ended up cutting...

I have had my new BX2350 for about 6 weeks. Two weekends ago I went and grabbed my new box blade to try and maintain my hilly, rainwashed driveway. The tractor performed very well (as long as I didn't load the blade up with dirt and run out of traction going uphill). When I started working at...

Would like to attach a couple of halogen driving lights from Harbor Freight to cab of my BX2350 for use when snowblowing. Where's the best place to tap into the electrical for this? Says 15 amp fuse on the lights. Also, blew 2 fuses last season when operating the electric chute rotator while...

I recenlty took delivery of a new Kubota BX2350 with 54" deck and fel. Have approx. 25 hours on it so far.(half mowing, half landscaping) It's doing everything I thought it would. :) My only complaint so far is ...when stopping in reverese the pedal seems very sensitive. It stops very abruptly...

It looks like I am just about there. Going to go Kubota BX series, the only decision left is BX2350 with FEL and attachments or the BX24 and attachments. I sure like the idea of the backhoe and can see uses for it, but there is the extra cost at this point. I could add a Woods later but that...

When I try to raise my box scraper slowly, nothing happens until mid travel of the lift handle then at that point the transmission/hydraulics start to growl. The scraper does not start to lift until the handle is moved farther back and then it raises at a rapid rate. In other words its all or...

Hello, I recently purchased a Kubota BX2350 with MMM and FEL and I had nothing but problems with it. First, the mower deck wouldn't go up and down, it gets at "Top" and get stuck there. Second, the second time I mowed (the first time was only for about 10 minutes), the back wheel and axle came...

Is there any advantage (easier?) to simply removing the bucket off of the FEL, rather than the the entire unit? I would remove FEL for better visual and clearance while mowing, just wondering if bucket removal, only, might be an option? I don't have a storage/space issue, but for those who...

Just curious, has anyone cross-reffed to find aftermarket oil filters for the BX2350 (905 engine)? My old Ford 1210 took a NAPA 1516 (WIX 51516) used them for many years. I heard a rumor that Fram's 3593A fit it? True??

Picked up my new BX2350 on Friday. Very nice machine! The 4wd hydro mowed my hills like a champ! My son is happy, no more push-mowing the hills. ;) I previously owned a Ford 1210 4wd gear shifter since 1989. Given that , I have a few Cat 1 attachments lying around. (Also am the keeper of my...

Tell me this gets easier. Just got the tractor yesterday.. I had no problem getting the loader off or back on.. smoother than my bigger L3130 because I can budge the loader around by hand to get it in the proper position. The mowing deck (60 inch) came off just as it's supposed to. And, I had...

This makes the third BX in my yard (the new BX2350 is actually my neighbor's). I started out with a BX2200 several years ago. Things have changed a lot with each model. The BX2350 is a REALLY nice tractor. He will use it mostly to mow and snow. He plans to keep his JD but I am wondering if he...

Finally got the Curtis cab for my BX2350 just before the real snow fell this year. Now I want to get it off for summer. Tried taking off the doors and mowing w/the frame in place, but it hinders too much movement around/under trees, etc. Anyone else taken one of these off yet? I have a hoist...

I am trying to decide between a BX2350 w/60" mmm and FEL and a like equipped B7610. The B is $14,900, the BX is $11,900. I drove both today just around the dealer's parking lot. I liked the feel and size of the B best. I'm just not sure the extra $3K is worth it. I have 10 acres, 7 in...

Has anyone had any experience using the bagging system w/ the 2350? How much of a pain is it to remove & reinstall? How well does it pick up leaves (since that's my primary use for it)?

In the near future I am going to be looking into purchasing a new BX2350 with 54'MMM, front mounted snow blower and a tiller. Can anyone give me a rough idea what this will cost? Tommorow I am going to call a couple dealers in my area and see what they say. Any help would be appreciated! Thanks Bob

I have a problem getting the mid mount mower links to lower to mount my mower deck. Took unit off last year and had zero issues. I heard mention of a "stowage" position you can put them in so they don't raise and lower while just using the 3pt. Has anyone heard of this? I see nothing on that in...

Went out early the other morning to pickup some plowing jobs.. Got an hour into it on flat ground and had been running about 27-2800 RPM's, it just died out to around 500 rpms.. I tried reving it backup and it just sat there.. Finally after a few seconds it was back to normal and I started...

I have a new 2350 and after really working this machine hard I would like to add a backhoe. I see some aftermarket units thats attach to the 3 point hitch, while others have a whole sub frame? Whats better and why?

Hello all, long time, no speak. I am one of the few people that can say they bought too much tractor. I ended up seeding only about 2/3 acre of grass, and it is all slopes and oak trees. My B7500 is too big for mowing and grass catching, which are my too main functions. My loader sits in the...

are you able to operate both raising of the loader and dumping of the bucket at the same time or do you have to do them one after the other? thanks

I picked my new radiator cover from the dealer today. To recap, I hadn't even had a serious complaint, but he remembered at delivery of the tractor that mine didn't fit snug, so he ordered me one under warranty...called me and swapped me. there isn't a lot of difference in looking at it...the...

Got my BX2350 this past Spring & ordered front snowblower and a Curtis cab as part of the package. Cabs had not been produced to fit this new model yet at that time, so I was supposed to give the dealer a call in the fall for them to pick-up and install blower and cab. Now they're telling me...

Finally got around to installing the block heater I bought last March. Thought I'd post it as a project. Step 1: Found it was easier to remove the lower radiator hose from the radiator to drain the system. Attached: Pics of the Kit and the hose removed... BTW: the same kit is used in the...

Hello all, I've been faced with a decision to make in regards to tractor selection. First the question and then the details. Would you opt for a new BX2350 w/ FEL and 60" MMM or a 2003 B2410 w/ 60" MMM and a NEW 352 FEL? The primary job of this tractor will be mowing, then minor ground work...

i was just wondering if it has cruise control? thanks

BX2350 just hit 50 hours. Looked under the hood today & surprised to find all 3 bolts supposed to be holding cooling system reservoir tank on had all vibrated loose & disappeared. Worse yet, plastic reservoir then apparently leaned forward enough to rest up against belt pulley and ground a...

Well, I understand what everyone means about using the BX with FEL at night... Difficult to see at all times, so I'm ready to add some lights. Any Suggs? Doesn't the BX have a true alternator, instead of a generator?? I thought I had read somewhere that they upgraded the BX2350 from the...

Went to the local dealer and got pricing on both units with a FEL and 54" mower. The difference is about 1,555. I noticed that the B w/FEL will not lift as much as the BX. Is this due to CoG. The BX is at 6.5 and B at 12 inches ground clearance. Can't decide which one to get. Have 5.5 acres...

Just came from the dealer and was given pricing on both above with FEL which came to 1,555.00. So what is a better buy. Looking at a total of 5.5 Ac. with at least 3.5 to keep and maintain. Need the FEL surprised to see that the Bx can lift more than the B, is it because of the CG. or what...

I just brought home my BX2350 last night and put about 2 hours on it today. It is a sweet machine, but I have a couple of questions.... When idling, I hear a slight whine from the hydro and when I rev as I rev it up the noise gets louder. Now I know that some hydro is normal, but this is...

I can't freakin believe this day has finally come. I registered here to find out about buying a BX2200 in the spring... Found out it was upgraded to the BX2230, and the BX2350 just came out. Although there have been a few issues posted about cracked fenders and such, I still believe this...

Anyone tried this "quick hitch"? Harbor Freight Tools - Quality Tools at the Lowest Prices Will this work on a BX2350? Anyone using anything similar they would recommend? Seems like it would make life a little easier for $69.

I just completed the deal to trade my bx1500 with mmm and fnl for a new 2350. Delivery is tomorrow AM. I've been very satisfied with the 1500 but thought a bit more power would better facilitate gravel drive upkeep with Woods 48 in box blade and offer the possibility for a few more...

Well, I finally have pulled the trigger and told the dealer to ready my NEW BX2350... ;) $12,200 for BX2350 w/FEL, 60"MMM, and R4's.. Extra set of Turfs w/wheels $300.00.. I won't get to pick it up till sometime next week, but I'm severly struggling on purchasing the turfs. My neighbor...

Have my BX2350 just over a week and put a whole 9 hours on it. Today I turned the headlights on and heard a loud somewhat grinding/clanging noise under the hood. This noise would ONLY appear when the headlights are on. The blinker, hazzards all function free of noise. I looked under the hood but...

Yes, another BX2350 versus JD2305 topic. There is a plethora of information on here about these two models, and I don't want to kick the dead horse some more, but there are some things I've noticed that I havn't seen mentioned anywhere. I'm down to these two models, and each are right around...

Yesterday after several weeks of research and reading this forum, I purchased a new BX2350 with 60"mmm and R4 tires. Total cost $9,995 plus tax. This is the first hydrostat I have owned or driven. As many posts have stated, takes some getting used to. The main problem was when backing up...

Upon checking my front axle fluid last night, I noticed that there is no oil on the dipstick -- obviously I need to fill it some, but I only have 20 hours on it. I have a couple of questions: 1) I noticed that I can clearly see the axle shaft -- is this normal? 2) I assume the tractor was...

Many buy their tractors out of state due to a 1000 - 1500 price difference. Friend is also looking at the 2350 and curious if it worth driving 7 hrs. for a 12-1500. price difference? Local dealer wants 13500, Dealer 2 states away is willing to sell for 12-1400 lower? It is for a farm...

Interested in experience with front mount dethatchers...the most interesting I have found is from JRCo...they do make a mounting kit for the 2350. http://www.jrcoinc.com/attachments.html Figure dethatch, mow, bag would be more efficient than tow behind Thoughts? C-AND-A

Dealer in NH (Chappell Milford) just quoted me $10,800 for a 2350 with 60"mmm, no FEL -- already have a bigger tractor with that. Kubota has 0% financing for 3 years. Does this sound fair. I've heard the service is excellent there and it's only 5 minutes from my house. Thanks.

I have been looking at the BX2350. I will be mowing 2 acres with some hill. The Kubota dealer was here today to look at my trade so I asked what tires he would recommend. He suggested Bar tires on the rear and Turf on the front. Does anyone have this combination and is this a problem having...

Does anyone know if a bagger from a BX2230 will work on a BX2350? I realize the decks are different, so the boot might need some mods, but I was wondering more about the 3 pt hitch setup.

Does kioti have or plan to have a model competitive to kubota bx2350?

I am looking to take advantage of the 36 month 0% financing... I am being quoted $15,400 for 2350, 60" MMM, bagger, FEL, ballast, grill guard, two bucket hooks (welded/painted) - I have not negotiated yet, but getting closer. I think there is probably $1000 in this price to play with...? Does...

I'm looking at a bx2350 primarily as a mowing machine on a hilly 5 acres. I'd appreciate input on price for the machine+belly mower. I've a kioti ck30hst with fel/bh for the other tasks - it's just to big for the mowing circumstance. Thanks.

I recently purchased a BX2350 to complement my L5030. I noticed an issue with the HST when traveling in the reverse direction. When releasing the reverse pedal after traveling backward, the tractor stopped immediately and made a small movement forward resulting in a rough ride. Since I owe...

I have some house remodeling to do and instead of renting a dumpster, I'm thinking of renting large open trailer (uhaul 6x12) to park next to the window for the demolition debris (instead of walking it to the other end of the house to a dumpster). I'll have quite a bit of debris, so this would...

Just did the 50 hour maintenance on my BX2350 and thought I'd drop a line on some things I found interesting: 1. The engine cowling is easier to remove, but harder to reinstall by yourself due to lining up some tabs on the operator end. 2. Noticed that there is no longer a threaded port in...

New member, but been reading a ton of posts and reviews before I pull the trigger. I'm really tossed up between these two models. I have about 2.75 Acres (1 to mow), on a hill. I've been quoted $13,410 for a BX2350 with loader & 60"MMM. I believe the BX24 is about 3K more? Anyone that got a...

Does anyone know if there is an extra wire/lead for a work light on the new BX tractors? I looked under my seat and couldn't find anything obvious, but haven't checked under the fenders yet. Next step is to call the dealer, but I thought you guys might know. Thanks.

I can get a left-over 2230 for about $700 cheaper. Is there any great advantage to the newer BX2350? I think the BX2350 looks cheaper.

Hi all...after a couple of weeks of minor use so far, I have a couple of things to state/ask. I have found that the seat safety switch is much too sensitive. Just leaning from one side to the other causes the motor to cut in and out. There are places where you have to lean for weight...

Last night while mowing, the seat on my BX2350 became quite loose. It appears that the front left mount/post wants to slip out of it's socket (if that makes sense). The cotter pins are not missing. On the same mount there is a spring-loaded clip that activates a switch -- this clip doesn't...

When my RPM's are between 2400 and 2800 with the mower deck running, I hear a high pitched whistle. It's not real loud, and I'm having a hard time locating it. It seems to be coming from the deck itself or the mid-PTO area of the transmission. The sound is only there with the mower deck...

So after reading countless posts here and getting lots of good advice - My wife took me on, as she called it, a "Tractor Visitation Day" - We looked at a bunch (great day)... After deciding that the SCUT size was where we belonged - our search narrowed the search down to two tractors - the...

Thanks to a variety of posts on this forum I finally jumped off the fence and ordered a BX2350 w/ FEL, fine cut MMM and scraper blade. Can't wait to get it. Thanks to all who offered helpful info

Just wondering what size drawbar should I purchase for my BX2350. Thanks.

I am looking at a BX2350. Got a price of $9,850 which includes a 60" MMM, and an additional $2,600 for a FEL. My inquiry relates to the difference between a regular MMM and a "fine cut" MMM. Can anyone provide any guidance on the differences? I have about one acre of lawn and 3 more of...

My tractor was stolen and Insurance will be covering it. I spec'd out the BX2350 and I think that's what I wanted. Insurance has spec'd out the Massey GC2300 (and it's more expensive). Can anyone tell me which would be a better tractor. I was really wanting the BX2350. thanks

I've had my new BX2350 for a couple weeks now, but I'm eagerly waiting the arrival of my bagger... apparently they are very back-ordered. The Kubota website doesn't even have a picture of it, so my guess is that they might have been substantially redesigned and perhaps late to production. Does...

Looking for some help. I've looked all over the Internet and the dealers haven't been much help. Anyone know the widest width of a 2350 with the 54" MMM? I have a 8x5 foot trailer and want to know if it will fit on with the deck attached. If not, how hard are they to remove? I have a Troy...

Just curious how many BX2350 owners are out there or how many of you are considering the purchase of one? Thanks!

Here's the deal... Currently using a 4x4 Yammy Wolverine with a 42" blade to plow my circle blacktop drive.. One side has a major hill. I only have a vertical lift, manual tilt on the blade so I can clean the 8000 ft drive in about 5 - 10 mins. Neighbor has a bx2200, with the plow, no FEL...

Hi all, I soon hope to be a BX2350 owner. I have a question on the 3PT. I currently have a Woods brush cutter and a rear blade that I have been using on my 9N. Will these fit on the BX2350? I looked at a BX2350 today but did not have a tape measure with me to see how far apart the 3PT arms on...

Ok..need your opinions. I've narrowed my search to a BX2350 or a B7510HSD. BX2350 with the 242 FEL, 60"MMM @ $12900 delivered. B7510 with the 272 FEL, 60"MMM @ $14200 delivered. The dealer is not the closest to us but only 40 miles away and picks up and drops off free for warranty work and...

Has anyone here mounted a Woods backhoe on their BX2350? I'm a first time tractor wannabe-buyer, and while I love the idea of the BX24 I'm not sure I can justify the added expense. The BX2350 seems pretty much like what I need (FEL, mowing and a chipper), but I'd like to know that if I REALLY...

buykubota-ML-871648-ML- Kubota specific thread.

I'm considering purchasing a BX2350 w/ 54" MMM, 48" FEL and a 3 pt blade. My local dealer gave me a price of $14,782 (incl $763 frt). I don't have a clue about pricing so I don't know if this is a good deal or not. I'm in Central Washington. Thanks

BX2350 w/FEL & 60\"MMM - BEST PRICE EVER!!! I just had the wind blew out of my sail.......... I was looking at an ebay'd 2004 - 2230, FEL, 60"MMM, rear blade, 80+ hrs, warranty until Aug 2006, buy it now $11,600. Come to find out it's someone 7-8 miles from me and believe it or not, works...

I'm hopefully within hours of dropping the hammer and closing my deal on a new 2350 / FEL / 60' MMM.. Friend at work was going to buy a Kubota a number of years ago, but didnt' because of the dealer being very unfriendly... His dealer is telling me to bring my written BX quote with me b4 I...

Hi all, First post to this great site - thanks for all the great information. Looking to purchase my first tractor for the following: - Cutting down that part of 3 acres of grass/pasture (i.e. not lawn) that our horse doesn't eat - probably only once per month - Periodic moving around of...

buykubota-ML-866359-ML- Kubota specific post.

I am considering purchasing a Kabota BX series tractor with a loader and a snow blower. I would like input on which model (BX1850 versus BX2350) to purchase. I have 10 acres (mostly wooded) and mow about 1.5 acres. I have a 500 foot driveway to snowblow (western NY). Is the 18 HP model...

owning-ML-864944-ML- Moved to Kubota Owner Operating per the poster's request.

My neighbor just purchased a new BX2350 and then purchased a 3pt. spreader. The PTO shaft/coupler will not lock onto the rear tractor PTO spline. His buddy has a BX2230 and it fit/locked on the spline with no problems. The 2350 spline is about a 1/4" shorter than the 2230. I have a new BX23...

New presentation, details, specs, photos on the new 2006 BX Kubota units http://www.carverequipment.com/bx_menu.htm Enjoy and best wishes, Steve

Has anyone purchsed one of the new BX2350s? If so how do you like it? I had the Kubota dealer at my place today looking at my trade in and he is willing to give me about the same as John Deere will on a 2305. The BX2350 is cheaper than Deere, but I don't know much about the Kubotas. Are they...

Ok, bought a block heater and when I got it, it was different than I or the dealer expected. For my 2200,. it was a threaded style, but for the BX2350, I have to remove a soft plug in front of the injector pump. I don't have the special tool they make for this, so do I have to buy one or is...

Some of you may remember me, I had a BX2200 that I had modded to death. Well, today I took delivery on my new BX2350. and since I haven't seen a write up here for this new model, I thought I might post a few things.... It's not just a facelift to the previous models, this is an entire new...

http://www.kubota.com/f/products/bx1850.cfm and http://www.kubota.com/f/products/bx24.cfm

I'm planning on this being my next tractor, though I've also been considering the JD 2305. I wonder if anyone actually is using theirs yet and their impressions of it. Don't spare the details, a full review would be great.... FWIW, I used to own a BX2200 that I modded to death, it was a blast....

I'm itching to buy a new tractor this spring, and am looking hard at the BX2350. Has anyone seen or heard of the pricing this thing will be by the time it hits the street? The only thing I've seen is MSRP, and wow, are they proud of their equipment. MSRP of this thing decked out with the...

There's a BX24 in there too. Check out "Whats New" here: web page Russell in Texas