kubota l295

In researching hydraulic fluid levels for this tractor am I correct in that I check 2 different places. 1). The transmission level for transmission and 3 point at plug next to clutch pedal. 2). The hydraulic reservoir at the controls for the loader with dipstick. Thanks.

Can anyone tell me what this hole in the housing is there for? It’s dripping hydraulic fluid like a faucet that needs a new gasket or money going out the window like Bidenomics. 😵‍💫 6 volt VW Buses and dirt bikes I know a little about but tractors!!! Clueless.

Hello everyone, So a good mate of mines getting rid of his Kubota, the story is that he was using it, it started to become smokey. He then drove it for Abit, before he turned it off and left it for about a week. Come yesterday, he's tried to start it and it struggled and struggled and didn't...

Hello, I have a Kubota L295dt 4x4. Currently running 7-16 front tires and 12.4x24 rear tires. Wondering if I can change front tires to 8.3-16. I've come up with 0.656 ratio for my current setup and 0.695 for the replacement setup but I can't find my transaxle ratio anywhere. I think I'm at +6%...

I recently bought a 1983 kubota l295dt. It came with power steering well it was leaking bad. I removed it and put the steering arm back in place (the dealership still had it). I filled it back up with hydraulic fluid now the front loader with not raise or tilt the pto is spinning and the 3 point...

No FEL, thinking about including FORD 5' snowblower. Unknown hours since meter does not work. Second owner. Full sets of (old ) ag tires as well as (newer (2-300hours ) turf tires. Tractor is in good running condition and in Massachusetts. Sheet metal is in ok shape with some dents...

Yep, your old cutting edge is worn out and you are about to get into the bucket itself. You don't have to spend lots of money here if you have a little 110v wire welder. Get one. You won't regret it. Oh yeah, get an automatic hat and a grinder too! While you are at it, talk the missus into...

Sooner or later, the four bolts that hold the steering column on the transmission are going to get loose. Tranny juice will splash out from under the column, run down the side of the critter and drip all over the place. I tore the whole thing apart, made a gasket to go between the column and...

I'm looking at up sizing from my little 18HP Kubota with turf tires, to something that can actually pull and has a loader. I'm on 20 acres, need to mow some of it occasionally, mainly wanting a loader to move dirt and a big enough tractor to plant a couple acres worth of different things...

Hi Guys, My tractor came with a hoe on the back instead of the 3pt. Now that the hoe is removed I been trying to get the right 3 pt configuration. I have the right check chains, but have managed to break both cheap Chinese lower links one at a time by grading in reverse. One strong little...

Brand new to your forum. My old Ford is about to die and I'm interested in a Kubota around the corner from me that looks like it just came out of the crate. It's beautiful. He's asking $11,900 but flexible...seems high for a 33 year old tractor but comes with some attachments. Any idea what...

Engine is overheating. Replaced head (new) 100 hrs ago, new water pump last year, new thermostat, temp sender, radiator has been boiled out and rodded and is like new. Replaced soft plug on block behind clutch. Other incidentals include new gaskets where needed. New starter, alternator...

I have a gray 2202DT and started having problems. Hard to start and then wouldnt start at all. I replaced the ignition and battery. Then it just cranks. I started to replace the gloplugs and had to remove the oil filter. Upon removal I noticed some metal pieces resting in the bracket for the oil...

I was replacing the transmission fluid and dropped the spring and metal screen filter as I was removing it. What order and direction do they go? Top of filter screen first, which would put the solid metal plate at the bottom, then the spring, and then the o ring and mounting plate?? thanks, bob

Hi, New to this forum and first return to tractors since my childhood with Fords from the 80's. I've purchased an old 5 acre old farm and want a tractor to do the winter plowing and help me recover 3+ of the acres which is a mess with alders which have prevented proper drainage for maybe 50...

Can anyone help me with hyd troubles on my L295DT? Any info out there for the backyard mechanics like me to troubleshoot hyd troubles on this tractor and how to plumb this tractor for a loader useing the tractor hydraulic pump instad of a PTO pump. Thanks for your help

I have a L295DT with a 1200 HD loader that is now plumbed from the PTO pump along with the backhoe. I need to change the lines so I can run the loader off of the tractor pump so the loader can be live. Can anyone tell me how and where to connect the lines to make this happen? Thanks for your...

How and where do I check to see if the hyd. pump is working right. Also where could I tap in for attachments. My first Kubota and not very familiar. Thanks for your help in advance.

Has anyone had experience with fixing the 4wd on a L295. How difficult is it to remove the front drive shaft? Any suggestions, Thanks

I recently bought a L295 kubota with a loader and backhoe, both the loader and backhoe hydraulics are run by a PTO driven hyd. pump. It does not have a live pto, so everytime I depress the clutch the loader does not work. Want to hook up the hydraulics directly to the tractor. Need to know...

I may have a chance to buy a 1975 Kubota L295DT. the clock says 2300 hours, I think it is right, the tin is rusty and dented, it appears to have some small leaks, the tires are about 50%, and it has an FEL. It is part of an estate that I will have first shot at, I know the family well and they...

I'm trying to establish the present value of an old 1988 Kubota L295 in "rough" though operational shape. This is a farm rig that has always been stored outdoors. It is operational though often difficult to start. Reply: ddelponte@hotmail.com

Hello everyone, I am posting for my wonderful 80 year old neighbor. His 30 year old L295DT finally needed it's first repair ouside of routine maintenance. He blew a hydraulic line while using the back blade to clear his driveway and replaced all of his lines today. Unfortunately, he cannot...

The tachometer on my 1980 L295DT has stopped working. The arrow on the gauge does not move when the engine is operating. I checked the connection on the back of gauge and it appears to be secure. Any ideas on what could be causing it? I have been using the tractor for a year using the engine...

Any ideas on a complete motor replacement option for a '95 L295DT?

Last spring my son in Utah bought a Kubota L295DT, with attachments. He is the second owner. I've been looking around for him for a source for a ROPS. I did find one company that can provide a ROPS for the two-wheel drive version, the L295, but that will not fit the 4wd version. Might...

I've got an early 80's Kubota L295DT tractor with Low Compression, I've had two different dealers tell me you could not get a rebuild kit, each part would have to be bought seperately...just wondered if anyone had experience with these tractors and getting parts? or should I just junk the old unit

I am working on a L295DT front end loader. I understand that the loader is not a kubota product but the name plate is gone. Is there anyone that knows the brand of the loader I might have and where can I get parts for it? thanks ducky

I'm looking at buying this tractor. Its runs good. Looks like ****. FEL has alots of re-welded areas. What should I look for with one of these? Advise? $6,000.00 purchase price.

Hi, I have a Kubota L295DT with an after-market front end loader. I believe the tractor and loader are late 1970's vintage, and have learned that the loaders were typically after-market add-ons during this period. Based on other posts and pictures here, I assume it is something like the...

Any info you can give me about the L295DT. I found one for what I think is a good price $4800. Is that a good price? Is this a good machine aside from the fact that its a Kubota :D How much does it weigh? How does this compare to the B7100? Can someone post comparison image maybe with someone...

Loader Control Valve Replacement \'79 Kubota L295DT I have isolated the reason for my loader bucket slowly drooping. The Control Valve. Although the lift valve is fine, the curl valve is leaking. Since the company that manufactured the unit has been out of business for 15 years, I thought I...

For owners of L295DT tractors - is the long tie rod between the wheels supposed to be straight? Mine has a slight upward bend to it. Thanks for checking.

I've just bought above tractor (sight unseen) and owner has advised "runs but motor fumes & water pump leaks". Anyone out there know of possible/probable cause symptomatic of fuming issue and a good source of parts. I'm based in Auckland, New Zealand. Thanks.

oil leaking out do you know were to get parts and a blue print ps it is a after market power steering

I just bought a Kubota L295DT about 3 hours ago. It has a few small issues to address that won't be too difficult to fix, but there is one that has me puzzled. The 3 point raises and lowers OK but when you release the lever it falls back down and then of course the hitch does the same. There...

Need to install front end loader. I was told I need A power and beyond valve

I lost reverse on the L295 that I use and upon removing the gear shift lever assembly/cover I found the forked gear moving arm was broken for the reverse. I replaced it but then ran into the problem of one of the other forks would not slide back and forth like the others do. There are little...

I have a L295DT with a Kubota loader 1200HD and a cab. Need to remove loader to do some engine repair, can this loader and cab be removed in one piece, or does it need to be dismantled? I have a service manual for the tractor, but have not been able to find anything on loader and cab.