First time welder type suggestions.

   / First time welder type suggestions.
  • Thread Starter
#51  
Here is another excellent welding text that you can use to self teach. Welding Principles and Applications by Jeffus 500 Service Unavailable Error The new edition costs over $200 but the 2007 version can be had used for a little over $20 from Amazon. I've purchased a number of books and taken a couple of classes and the Jeffus book really stands out. It is written as a textbook with theory and practical exercises as well as numerous tips. Well worth $20.
Wow, what a book! I can see why it was original $162 retail. $21 was a deal. Large hardcover,911 pages with lots of easy to understand illustrations. Thanks. I'm going to check out the other shield arc suggested too Sent from the mountains
 
   / First time welder type suggestions. #52  
The front end of the Frame on our CC 7532 snapped due to end loader stress.. I was so upset! It drove the Plastic fan into the shroud and shredded it, plus bent some body parts and broke the front axle pivot mount. new frame alone was over $1200.00 without labor to replace it.. I bought a Hobart Stick Mate some 1/2" x 2" steel, some Grade 5 Bolts and went to work. It turned out beautifully! I had some guidance from an good friend, but since that project, I built myself a Three Point 65Galllon Lawn sprayer with a 8' boom.. Once you get a welder, there is so much you can do. I also have a Hobart MIG 225A.. The gas is expensive at first because of the tank purchase. I have to be honest. The stick is my go too.. You can weld thinner metals with lower amperages, and less penetrating rods. I used to have a 115v 90A and it was so limited, I sold it... I do not regret getting a stick at all! It can penetrate very well. No matter what you do, get a good helmet and gloves. Protect your skin from burns.. Even sunburn... Good Luck!

If I were a professional or had the extra coin, I would have gone with Miller.. I have zero complaints about Hobart..
 
   / First time welder type suggestions. #53  
The front end of the Frame on our CC 7532 snapped due to end loader stress.. I was so upset! It drove the Plastic fan into the shroud and shredded it, plus bent some body parts and broke the front axle pivot mount. new frame alone was over $1200.00 without labor to replace it.. I bought a Hobart Stick Mate some 1/2" x 2" steel, some Grade 5 Bolts and went to work. It turned out beautifully! I had some guidance from an good friend, but since that project, I built myself a Three Point 65Galllon Lawn sprayer with a 8' boom.. Once you get a welder, there is so much you can do. I also have a Hobart MIG 225A.. The gas is expensive at first because of the tank purchase. I have to be honest. The stick is my go too.. You can weld thinner metals with lower amperages, and less penetrating rods. I used to have a 115v 90A and it was so limited, I sold it... I do not regret getting a stick at all! It can penetrate very well. No matter what you do, get a good helmet and gloves. Protect your skin from burns.. Even sunburn... Good Luck!

If I were a professional or had the extra coin, I would have gone with Miller.. I have zero complaints about Hobart..

I love fixing stuff rather than replacing broken parts. The more my old mowers etc look like escapees from a Mad Max movie the better as far as I'm concerned. Drives my wife crazy 'cause they are butt ugly but as long as it's safe and solid I'm happy. Last week the flimsy handle on our battery powered push mower broke so I rummaged around and found some 1/8"x1/2" sheet metal and made me some splints that I attached with screw clamps and duct tape. Looks gnarly and is more solid than when new.
 
   / First time welder type suggestions. #54  
The front end of the Frame on our CC 7532 snapped due to end loader stress.. I was so upset! It drove the Plastic fan into the shroud and shredded it, plus bent some body parts and broke the front axle pivot mount. new frame alone was over $1200.00 without labor to replace it.. I bought a Hobart Stick Mate some 1/2" x 2" steel, some Grade 5 Bolts and went to work. It turned out beautifully! I had some guidance from an good friend, but since that project, I built myself a Three Point 65Galllon Lawn sprayer with a 8' boom.. Once you get a welder, there is so much you can do. I also have a Hobart MIG 225A.. The gas is expensive at first because of the tank purchase. I have to be honest. The stick is my go too.. You can weld thinner metals with lower amperages, and less penetrating rods. I used to have a 115v 90A and it was so limited, I sold it... I do not regret getting a stick at all! It can penetrate very well. No matter what you do, get a good helmet and gloves. Protect your skin from burns.. Even sunburn... Good Luck!

If I were a professional or had the extra coin, I would have gone with Miller.. I have zero complaints about Hobart..

I love fixing stuff rather than replacing broken parts. The more my old mowers etc look like escapees from a Mad Max movie the better as far as I'm concerned. Drives my wife crazy 'cause they are butt ugly but as long as it's safe and solid I'm happy. Last week the flimsy plastic handle on our battery powered push mower broke so I rummaged around and found some 1/8"x1/2" sheet metal and made me some splints that I attached with screw clamps and duct tape. Looks gnarly and is more solid than when new.
 
   / First time welder type suggestions.
  • Thread Starter
#55  
No matter what you do, get a good helmet and gloves. Protect your skin from burns.. Even sunburn... Good Luck! If I were a professional or had the extra coin, I would have gone with Miller.. I have zero complaints about Hobart..
The cloves and cheaters are next on the list. I already had some Kevlar sleeves I think would help too. . Also a Mig welder to compliment the stick power arc 140st. Helmet should be here today. I wouldn't want to attempt using the face shield that came with it. Sent from the mountains
 
Last edited:
   / First time welder type suggestions. #56  
The cloves and cheaters are next on the list. I already had some Kevlar sleeves I think would help too. . Also a Mig welder to compliment the stick power arc 140st. Helmet should be here today. I wouldn't want to attempt using the face shield that came with it. Sent from the mountains
As a new welder you should also take care to wear cotton or non meltable pants and shirt. Also, no sneakers. Leather ankle high work boots and make sure the pants are long enough to cover the boot when sitting. Also it is a good idea to wear safety glasses even when you have the helmet on.
 
   / First time welder type suggestions. #57  
I can't add much to what has already been said except I really like my Everlast PA160 stick welder. I TIG with it too. Yes the autodark helmets make a big difference.
 
   / First time welder type suggestions. #58  
My neighbor had a Century AC/DC unit out for sale sometime ago. He was asking $225.00 and it look like brand new.. Century is a subsidiary of Lincoln (Same Color too) If I hadn't purchased my Hobart StickMate LX, I would have jumped on it for 185-200.. Good price for a Dual model.. On old "Tomb Stone" unit can be had cheap! Every farmer in the USA probably had one.. Personally, I think Stick welding is the way to learn.. You must control the angle, Arc, feed rate, path speed.. then add in rod type, Amperage setting... I still don't have a great handle on MIG welding and my set up cost me about $1500.00 to get set up... I have CO2 and Argon Mix gas. I need to practice, but haven't had much time.. BTW I am not a super star welder with a stick either... But I can make due, have fun, and am learning.
 

Tractor & Equipment Auctions

Skid Steer Trailer Hitch Plate (A49339)
Skid Steer Trailer...
Ezgo Electric Golf Cart (A47307)
Ezgo Electric Golf...
John Deere WHP52A (A47307)
John Deere WHP52A...
2025 Swict 84in Bucket Skid Steer Attachment (A46683)
2025 Swict 84in...
Nissan 30 Warehouse Forklift (A47307)
Nissan 30...
2025 Dual Cylinder 72in Grapple Bucket Skid Steer Attachment (A46683)
2025 Dual Cylinder...
 
Top