OP
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 57,474
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
That’s good to know.
PowerTrac Specific Modifications
- Thread starter MossRoad
- Start date
- Views: 61553
BobRip
Elite Member
Nice simple modification to make it work with the PT. Good idea.
m5040
Platinum Member
- Joined
- Nov 23, 2008
- Messages
- 988
- Location
- CT
- Tractor
- Kubota M6040 L2250, JohnDeere 310D, Ford 841 Elenco, Ford 961, Trapmaster, PT180 w/LM bucket and 45" brush cutter, PT1430 Deutz w/grapple bucket, Antonio Carraro Tigrecar 6500. John Deere 5300. Former owned Steiner 430 max, Goldoni REV Maxter 7
I think that will only apply to the PT425 mounting plate. I tried it on my PT018 & 430 and it wasn't close.
ponytug
Super Member
Aluminized wire loom protecting the glow plugs on the 1445 Deutz BF3L2011 engine.
In hindsight, I probably made the heat issue worse by trying to prime the muffler with Rust-Oleum Rust Reformer, which I found out later has an upper limit of 200F. It turns black as it dries. It then proceeded to flake off in the first hour, leaving rusty metal underneath, so I am underwhelmed at its rust reforming abilities as well.
So yes, sanded, prepped, and painted twice; once with the rust reformer and then sanded it down with an abrasive disk (way better than rust reformer or sand paper)
I used silver "high temp" paint the second time, but one that sets at about 400F, which is about all the Deutz can generate.
Did I mention that I love the intake heaters? They really help cut down the black smoke on starting below 40F for me. (Thanks @SpringHollow!) I am not sure that I need two, but they certainly work.
All the best,
Peter
In hindsight, I probably made the heat issue worse by trying to prime the muffler with Rust-Oleum Rust Reformer, which I found out later has an upper limit of 200F. It turns black as it dries. It then proceeded to flake off in the first hour, leaving rusty metal underneath, so I am underwhelmed at its rust reforming abilities as well.
So yes, sanded, prepped, and painted twice; once with the rust reformer and then sanded it down with an abrasive disk (way better than rust reformer or sand paper)
I used silver "high temp" paint the second time, but one that sets at about 400F, which is about all the Deutz can generate.
Did I mention that I love the intake heaters? They really help cut down the black smoke on starting below 40F for me. (Thanks @SpringHollow!) I am not sure that I need two, but they certainly work.
All the best,
Peter
woodlandfarms
Super Member
- Joined
- Jul 31, 2006
- Messages
- 6,136
- Location
- Los Angeles / SW Washington
- Tractor
- PowerTrac 1850, Kubota RTV x900
As requested. Raising of the Deutz
blower cover for better ventilation.
m5040
Platinum Member
- Joined
- Nov 23, 2008
- Messages
- 988
- Location
- CT
- Tractor
- Kubota M6040 L2250, JohnDeere 310D, Ford 841 Elenco, Ford 961, Trapmaster, PT180 w/LM bucket and 45" brush cutter, PT1430 Deutz w/grapple bucket, Antonio Carraro Tigrecar 6500. John Deere 5300. Former owned Steiner 430 max, Goldoni REV Maxter 7
Might be better if you lowered the backside of the deflector so the air stream hits the shield at an angle and not straight on.
ponytug
Super Member
Muffler wrap; lowered the temperature of the outside of the muffler by 270F, and the engine plus hydraulic oil by a chunk.
More here;
Posts in thread 'What did you do with your Power Trac today?'
Pre wrap muffler and oil temperatures
Post muffler wrap temperatures
All the best,
Peter
More here;
Posts in thread 'What did you do with your Power Trac today?'
Pre wrap muffler and oil temperatures
Post muffler wrap temperatures
All the best,
Peter
m5040
Platinum Member
- Joined
- Nov 23, 2008
- Messages
- 988
- Location
- CT
- Tractor
- Kubota M6040 L2250, JohnDeere 310D, Ford 841 Elenco, Ford 961, Trapmaster, PT180 w/LM bucket and 45" brush cutter, PT1430 Deutz w/grapple bucket, Antonio Carraro Tigrecar 6500. John Deere 5300. Former owned Steiner 430 max, Goldoni REV Maxter 7
Can you tell any difference in the noise level after the wrap?
OP
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 57,474
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
I'd be curious to see if that would make a difference on my 2001 PT425. Anything to reduce the heat under the hydraulic cooler would be a bonus, as long as it doesn't build up heat somewhere else, in my case.
ponytug
Super Member
Nothing too obvious to me, but the muffler didn't rattle beforehand, so I would not have expected a change. I guess the hotter exhaust gases might sound different, but I also wear Howard Leighton Leightning L3 (30dB NRR) ear muffs, so I don't know how reliable I am on this one...
All the best,
Peter
