Search results

well, problem is back again. everything else works fine but the load sensing switch when engaged the tractor doesnt move at all. in any case maybe someday i will get around to taking the switch apart. doesnt really matter as i really dont use it so when i have time to mess with it i will do it.

great info, forgot to get back to, yes i found the allen head and applied grease until it came out the allen hole. thanks again.

Sorry I can't help answer your questions but it is just crazy if the pump is not covered. that is part of the powertrain in my mind.

i know what you mean, they can be a real struggle to get on those rear wheels. i put string going through the rim and then tie each side to the chain, drive forward and it pulls it over the tire and around. actually my rims are solid so i drilled a 1/4 inch hole thru it and fish the string...

so go figure, i tried it today and it seems to be working!!! i guess maybe the button connector dried out. i think i might take apart the connector at the button and put dielectric grease in it anyway when i get a chance. if the other connectors/buttons for cruise control, pto are not too...

yeah, i have it cranked up to max 2450 rpm. i might try taking the switch out this weekend and clean the connector even though i keep in the barn and doesn't stay in the rain. but i did get alot o snow this year and i did plow while it was snowing and the dash did get fair amount on it.

I have a 2555 since new , 2017. Today i was using the box blade on driveway and figured i would try the Load Sensor button. it worked in the past but now it stopped working. tractor works fine using the box blade, good power, hydraulics work fine without using the load sensor button. when i...

i have teh same thing on my 2555 HST Open Station (2017). when sitting on tractor it is on the right hand side of the engine and as you can see by the fan belt. i knew about the grease fitting, i think i even posted it somewhere on here, but did not know about the allen head to check it. thanks.

i have 2555 woth 65b. only two hoses are used/needed. they plug into the rear ports. BUT you must have th detent type of valve. to the right of my seat there are the levers. one raises/lowers the 3pt. the other engages the hydraulic ports to flow the oil to those two ports. if you push...

i noticed a noise on my engine too at certain times, load/no load, rev it up or down. i sprayed a little silicone on the fan belt to see if that was it and it was since i didnt hear it again all day. just needed to tighten it up a bit.

I have one on my 2555, I live in orange county NY, i have started it w/o block heater in the single digits and with it. it definitely starts easier and warms up faster with block heater so i generally throw it on regardless when it gets below freezing and i know i am going to use it. to me it...

HI Sideskraft, allthingsdiy mike, i am sorry i accidentally deleted your comment and didnt know how to get back to you. attached are pics of where they are on the 2555. i think its #12 in the pic. dont know why it says DUMMY glow plug. I am sorry i could not gt back to you.

I bought wheel spacers (1.5 inches) so i can have the chains on without hitting the sides of the fenders, etc. i was looking in the manual and it states 262-282 ft. lbs. seems high to me. does that sound about right? do other tractors have it this high for a 55hp tractor? or maybe its a...

you can see where the bell/loop top bolts through the top boom. that is where you can see it bent down some. you see it circled.

I did the 150 hour maintenance and I have been meaning to ask my question the last two times i did maintenance intervals but kept forgetting until today. the lube diagram indicates there should be 2 grease zerks on the left side of the tractor by the brake pedal area but I have only been able...

Picked up 15 tons of 3/4 gravel for the driveway using load trail trailer and floated it with the front bucket.

Nephew dug out the stump last weekend., roots broke fairly easy, stump was about 2 feet taller but then loader was maxed out lifting it by trying to just pinch the wood part of it with the grapple. cut off two feet of stump today and it was able lift it no problem. I am so pleased with the EA...

Hi, I have a 2555 with backhoe. When I have the hoe mounted I push the hydraulic remote handle on the side of seat all the way forward so the hydraulic fluid flows to the backhoe controls so i can use them. When the backhoe is mounted i always leave the handle forward even when just driving...

Yeah, it is. I saw it when I was reading about LEDs on this site. Another member did this and i tried it. IT works great. It really has to be hit with some force to get it to come off or even move. the magnet has to sit flat on the roll bar and it holds on real tight. LEDs compared to...

spent <$100 on parts and put led lights on my 2555. WOW what a difference! THanks to other members for great ideas. I used 4 magnets and mounted 120W bar light facing forward ( combo flood and spot) and two 27W each facing rear. I bought 2 switches online for couple bucks each that light up...

well i was reading the service manual and came across something interesting. It mentions a suction filter and a line filter (both hydraulic i think) First i have heard if this. All the filters I have seen that can be purchased only mention one. I think the suction filter is the large...

well, am getting close to 50 hours. Ordered filter pack from Reubicon tractors, hope they are decent filters. I am very happy with the tractor. Got the EA grapple single lid and wr long 3rd function. nice. The only knock i could think of is I wish the rollbar would fold in the middle...

I used old pvc pipe and bought a 4 inch round rain spout drain for the bottom,screwed it into pvc from side with small screws, put some old 1/2 inch pipe insulation on the bottom and on side to absorb impacts. took another members advice and put masking tape over ext outlet to keep mud wasps...

just a pic of where i mounted ammo box for storage on my mahindra 2555. there is an unused welded on nut under the floor board so just got a bolt to fit and drilled a hole in bottom of box and bolted it down with couple of washers. the bolt is the same size as one of the bolts that holds the...

Well, getting more things and customizing the new tractor. I just got in the mail the wr long 3rd function but am not sure where the power beyond port is from the loader valve. here is a pic of the loader valve. it must be one of the top two hoses or the one on the bottom that I need to...

put ammo box/storage box on my 2555, also wrapped some old inner tube around loader hoses since they were rubbing a bit on frame by the valve control/lever. built two holders for fire extinguishers out of old pvc and mounted one to the left of the seat behind the 4wd lever and the other above...

I was thinking of that but the problem is with this rops it folds down at the base, bad design, most other rops fold half way up. i used some old pvc pipe and mounted it next to seat behind the 4wd lever and another one above the 3 pt in the rear of the tractor. will add photos after it stops...

Just got it the other day, tried everything out today. TLB. 6ft rotary, 6ft BB, 7ft rear blade, 6 inch PHD, pallet forks, loaded rear tires, block heater. Everything works. I like the dealership I got it from. Went there many times with questions, test rides, etc. Worth the trip for me...

hopefully i did this right. also tried to put under classifieds but it says disabled. thanks.

HI, i I have a MF 135 (I think) industrial yellow , with MF 200 loader. sat in barn for few years. engine turns over, won't start. clutch frozen. Power steering is screwed up. 2 aircraft tires on front. 2 very good ag tires on rear. chains, locking differential. 2 stage pto clutch...

Maybe it's just me and the way i think...BUT...if anyone from Mahindra corporate reads the forum its about time you update your website! 65B hoe has replaced the old hoe some time ago and still no info on the website. Also, I saw a tube video about new 6000 and 9000 series models and still not...

I have been hearing that mahindra has designed a new backhoe the 65B to replace the 75B. Do any of you guys who are dealers know why this was done? From what I understand the breakout force at the bucket and dipper are much lower than the previous 75B model. If this is true then I have to...