3 point

I bush hogged for a couple of hours on my L4400 and raised the bush hog up to move to a different location. When I pushed the right hand lever to let the bush hog down, it stayed up and won't move. I am not familiar with the workings of the 3 point but looking at it the lever turns a shaft on...

I have a New Holland TC18, the 3 point raises its own weight but standing on it is enough to make it go back down. Loader hydraulics and power steering work well. Hydraulic fluid is good in level and condition, new spin on hydraulic filter 3 hours ago. I tried turning the slotted head valve...

I have a NH T1510 that I bent the 3 point arms on. Completely my fault. I got my bush hog hung up and it twisted too much. Anyways...where can I get a good replacement set? I have purchased two different pairs (one online and one from Rural King) of "universal" arms. They both bent as soon as I...

Title says it all . I have one acre. A BX and a leg that makes pushing a spreader not fun

Hello everyone, working on my JD 2240 today . Putting the bushings in the rock shaft lift arms. Just wondered if any one else has ever done this, and if the new bushings took the play out or if the shaft may need replaced.

My 3 point hitch randomly stopped working yesterday. The arms are all the way down and will not rise. I have tried turning the knob beside the seat, I have also checked the draft position lever. Everything else seems to be working normal. Any ideas what I should do next? I had been using the...

Hey yall I just bought a john deere 750 tractor 4 wheel drive and I'm having an issue with the raising of the 3 point hitch I can raise it up fine but if I try to haul a trailor or anything with it it's weak and goes down unless I have it up all the way I've looked everywhere for options and...

Tractor had box blade left up for 2 weeks noticed it was up lowered it by handle while off and hydraulics won’t work now. It has no front end loader, and is a 3x9 manual transmission, fluid was fine changed any ways and so was filter still not responding at all. I can lift arms and they just...

I'm in the market for a 3 point spreader, I have searched this forum and cannot find a post related to my question. My L3400 has a quick hitch on rear and it looks to me if I buy a spreader that the control lever will be too far back to reach while sitting in the seat. Is there an extension made...

Does anyone know where you can get telescoping stabilizers to replace the turnbuckle set up. Turnbuckles are a royal pain to use. Thanks

Need some help getting to the root cause of my 3 point hitch dropping slowly and unintended. Tractor : Kioti NS6010 Hydrostatic transmission, 60HP Symptoms : 3 point hitch drops slowly when it is loaded with the weight of e.g. my flail mower. Over about a quarter mile of riding it will go from...

I have a Ford 4610 that the 3 point is sticking in the up position under certain conditions. It will move up and down with no attachment without problems. However when I connect my belltec tm 48 to the rear hydraulics and raise the 3 point it will not lower with the controls. If I...

I have a New Holland TC30 with a hydraulic issue. It seems like it could be kind of a generic hydraulic issue, not necessarily a New Holland issue, so I am posting it here. I have a loader on this tractor. It is not the New Holland one, but it is made for my tractor. The lift capacity for the...

Several months back I started a post on 3pt wood chippers. I thought it would be beneficial to others to post my thoughts and experience with both the above units. They were both run on the Same B3200 with 23 HP at the PTO. They both have good points, one had really bad ones. So read on and...

I have a Branson 47 and I find the lever for the 3 point linkage is not very smooth in operation and makes things a bit jerky when raising the arms, is there anyway to adjust it? Thanks

I am putting an accumulator on my Farmall 110c for the 3 point hitch. I believe the port is right under the cab but no one at my dealership can tell me for sure. I have also heard it may mess with my draft control but will worry about that more when I figure out where to hook it in. I believe...

I am putting an accumulator on my Farmall 110c for the 3 point hitch. I believe the port is right under the cab but no one at my dealership can tell me for sure. I have also heard it may mess with my draft control but will worry about that more when I figure out where to hook it in. I believe...

I have a question that I cannot seem to figure out the answer to. Let me pose the hypothetical. Let's "assume" you have a 1000# load on your 3 point hitch and you are able to lift it. The lower arms lift the weight and the top link steadies / adjusts it and keeps it from just flopping over. How...

I have a new to me ck3510 se/c HST because I couldn't afford a CK3520 that already has the rear lever to control the 3 point while connecting implements. Has anyone ever made this modification? I always wished I had one on my open station Kubota and now I really want one on my cab model.

I have a 1980s JD 770. The 3 point hitch rubs the tires and sway link turn buckles break if tightened enough to keep 5 foot bush-hog from rubbing tires. Is there a 'telescoping' sway link assembly available somewhere for my small tractor, like the one on Deere larger tractors, sliding metal bars...

Good afternoon, I am having some difficulty understanding how to properly raise and lower the 3 point hitch, when I watch a video on youtube, The operation is as simple as moving the position lever. Both Hydraulic remote "A" and "B" appear to be in neutral and nothing is attached to the rear...

Have a 1989 Curtis Grooming mower, in great shape, however the gearbox got damaged with a bad barring and now need to repair vereticle shaft and barrings. John Deere sold them. They now no longer make the gearbox and shaft. Any ideas on where to go to repair the gear box? Unit is three point...

4720H . was using my hydraulic wood splitter . All worked great lowered the splitter on to its wheels in the garage . Put it away . and then the 3 point arms wouldn't lift up. Hydrostaic drive works and the bucket functions??? Am I missing something. ? Where can I start to look. The limits...

I bought a new mt235 LS in April 2024 3 point hitch has been jerky since I bought it. Took it back to the dealer was told it is not suppose to be like that. After keeping it for 2 months was told they all do that. contacted LS USA customer service with little help. Does anyone else have this...

A question for you guys: My MF 158 3 points hydraulics lift drifts down when the diverter valve gives pressure to the external component, and there is a load on the 3 point lift. Before I go ahead and try to replace rings on the lift piston, is there something else that may cause it?

Left lift arm top threaded part ok,....bottom treaded part.....frozen will not turn or take grease. Right side like new. Don't know if I named correctly, top attaches to moving lift arm, lower to bottom arm, any way to do with out heating. Have tried with 40 inch pipe wrench for leverage but...

It's on my SIL's little Kubota B1550, but may apply to any brand. The issue is he has to hold the lift controller up, or the lever just goes to the "lowering" end. There's no tension on the lever, only has a movable "stop". I can't find any missing parts or tension adjustment, but this...

Just bought a ym3810d in good condition except for the 3 point doesn't seem to do anything, the guy I bought it from said he only used the tractor for the loader and has never tried to use the 3 point and didn't know it didn't work, I took a chance and bought it anyway hoping it was something I...

I’ve just taken delivery of an Enfly DQ404 tractor. I notice that I cannot lower the 3 point linkage arms without putting weight on them. I have fully opened the drop speed valve under the seat (which apparently is the common solution). I’d like to hear from other Enfly tractor owners whether...

I went to use my 3 point auger on my JD 4710 tractor for the first time in years. Everything hooked up fine but when I drop the auger to the dirt it won't screw down to create the hole. The lift mechanism is totally dropped, it just wont dig in. Any help would be appreciated.

Hello, Does anyone know of a way to get a 3 point hitch adaptor of some sort mounted to this bucket? Do they even exist? Before I start welding and drilling a bunch of nonsense to make this work, I wanted to make sure there's not some kit that'll attach to the bucket. I have a JD2155 for the...

When trying to use the 3 point today, it stays stuck in the up position. Made sure that the Lift-O-Matic was turned off but the levers are not changing anything. We can see that the levers are rotating on the back of the tractor, but they have no affect. We tried to put weight on the 3 point and...

Hi folks! Working with my grandfather on his newly acquired, low hour Kubota b7800 he bought to replace an older 541 case that was hard to get on and off of. We put a 5' rotary cutter on the Kubota. What we have found is that when you lower the mower it goes down until skids on the front drag on...

I have an old L3450 that sat for years. I got the engine going but the 3 point is dead. It was having major issues before the tractor was parked, so it’s going to be a bad piston / sleeve. The tractor has a ROPS and I was thinking about mounting an ATV winch to it to lift the blade or mower. I...

The 3 point arms on my John Deere 2155 will lift every attachment I have but won’t go down. Wondering if anyone had any advice.

Hello, I just picked up a preowned LS MT225S that came from the dealer with a backhoe installed. The 3 point hitch kit wasn’t given to the original owner by the dealership. Fast forward to today, the dealer has quoted all the parts I need for the 3 point hitch at just under $1k. Is there any...

I have a 48” rototiller that has no marking or stamps on it of any kind. I’m trying to ID it so I can try and get parts for it. Any help in identifying it would be appreciated.

Heard a snap while mowing today followed by a floppy mower when I backed up. A pin that holds the lower arm to the axle snapped. At first I assumed almost 20 years of abuse with the box scrapper took a toll. After walking the lot and finding the broken pin, I'm wondering if it wasn't a bad cast...

I'm in the market for a woodchipper and ran across these guys on sleaze bay. They have a machine somewhat similar to a Woodmaxx WM-8H which from my hours of research seems to be the top dog for my needs and compatibility with my B3200 (23 PTO HP) They claim to have been in business 20 years...

When lowering a very heavy 3 point chipper back to the ground I try to do it smoothly to avoid unnecessary strain or wear on the tractor, but it is difficult to prevent a bit of bouncing unless I just slam the lever forward and let the chipper drop. Is there a right or better way to lower heavy...

Other than the dealers, any place else to purchase the 3 point hitch set up for the Dk series tractor? Post the link below. Its appreciated.

I'm thinking about getting a 3 point land leveler to keep the driveway smooth and level out various spots around the place. Just light duty stuff. I'm thinking about the Behlen 7' model from Tractor Supply given the good price point. I don't think I need scarifiers since I have a box blade with...

Plowed about 3 acres and then this started happening. The hitch would raise all on its own and sometimes just sit there and go up and down, wouldnt stay in set position, just a mess. Worked good for a wile. I called the tech at dealer and he basically said i just need to adjust knobs… well they...

950.00. Finishing mower Edenton/hertford, NC https://eastnc.craigslist.org/grd/d/edenton-finishing-mower-point-72/7729159399.html

My hydraulics need rebuilding, it struggles to lift even moderate loads and bleeds down quickly when I shut the tractor off. But when these are rebuilt, are they capable of lifting a 60" brush hog, 72" finish mower? What about a 60" blade? I'm just trying to decide if it's worth rebuilding it...

Hello. I have a tc45d tractor and I was using it today all morning. I lowered the 3 point hitch, got off the tractor to move something, then got back on and the hitch will not go up. I looked at the contol lever and it is hooked up and moving. I checked the oil level and it was good. everything...

Here is a little project I just completed. I was wanting something different than my old "standby" 3 point carryall and I settled on this. I started with a used jobox I bought off marketplace and had some 3" channel and other scrap steel laying around. I started cutting, grinding, welding and...

The 3 point lever has been getting progressively harder to move over the years, now requiring dismounting from the tractor and pushing with two hands. I sprayed what I could reach with some PB Blaster lubricant, but even then I ended up bending the lever pushing too hard on it tonight. There...

Attachments bob when raised, I was dragging a disabled trencher out of a ditch with the 3 point hitch, lifting and dragging, and something gave, I have the sub control valve removed from the tractor and need advice on what needs repaired or a repair shop near Batesville Indiana, any help will be...

Hey guys i have a ih 424 utility my 3 point wont go down i pulled off cover below seat and found this item it is around 1 1/4 long has a small hole at one end large on other dont look like its broken would anyone know where it might go

Hi! I have an old Ford 1700. Recently, the control arm for the 3pt lift has been "slipping" up. Messing around with it, it goes down with resistance, but when I pull on it, it moves pretty easily, which means if you hit a bump, it will lift the 3pt arms, which makes grading really annoying...

I have a mf 1260 from auction . Was never used as a tractor. Nothing on the 3pt was ever hooked up or used. The lift arms are all the way up. Fo I need to put something on the 3pt to get them to lower????. What are the 2 3pt levers rt of driver seat for? One or left and right lift arm? I'm...

Need some help in figuring out why my front loader will work, however not at strongly and will lower without contant monitoring, while 3 point will not go up or down....changed filter, not leaking hydralic fluid....any suggestions? Thank you, JMS

Anyone know where I can get a parts list for what I believe is an old yanmar ybh-600

Not coming up with any results, so I'll just ask here. Rather than try and fab up something, I've been looking for a 3 point implement frame to be used to modify or make a 3 point attachment. I cut apart an old 3 point carryall to repurpose the mount, but I need another. An internet search...

John Deer 5203 three point hitch control levels stuck in position, however my pull type hydraulic remotes works well, Any suggestions.

I have a 4530 4wd T2. Today when I tried using the tractor, the box blade wouldn't lift. When turning off the ignition the blade immediately raised about 3 inches. In order to get it fully raised, I had to turn the tractor on and off. It lowers fine and all other hydraulic functions work...

We had a new road cut and 3/4 crushed rock laid - about 500 feet and 10-15% grade. We also have another driveway (800') I maintain with my grader blade (nice crown there). Anyway, for the new road, I have used my box blade and grader to spread the crushed rock, but not ideal - doable, but I am...

I recently added the Ventrac Three-Point Hitch kit to my 4500Z machine. The kit is labeled as a Cat 1 hitch. When I try to attach certain Cat 1 implements to the unit's hitch, the lift arms do not extend wide enough to accommodate the pins on the attachments. On a rake, I had to purchase the...

We have a TYM T1054 tractor. Having some issues with hydraulics. This thing has the Bosch control in the cab and we have been learning more and more about it. The control is throwing a code 22 that means no communication from the potentiometer. This controls the and tells the brain where the 3...

Hello recently upgraded to a bigger utility tractor from a smaller ford 7209 and the issue is the stabilizer spacing for bottom implement pins. the stabilizers won’t come in enough to hook both pins in the ball bearings and wondered what the solution was for that is there was one instead of...

About 10 hours in, and i've worked it hard with lots of dirt moving. Couple issues: 1) I went to pop the hood and check things out and the front guard bracket is slid back and unable to open hood (see pick). 2) the lower hitch points swing back and forth and could easily hit the tires. not...

I have a 2015 Max 26XL bought used with a backhoe but i have no 3 point hardware. I priced out what i need from Mahindra and its over $1600 the lift arms are 500 ea. If you have a 3 point not on the tractor I could use the dimensions of the lift arms and turn buckles anything on the 3 point...

Got a dumb question. I have a B2601. The three-point hitch lift only seems to engage when the lever is in top of its range (7-8). I've had it for a couple of years and I don't remember it having that much 'slop'. I've got a box blade on it now, but I seem to remember it doing it with the...

So I have had this tractor for about a year, Mahindra 1538 Cab with FEL and Backhoe. Got all the connections for the 3 point and took off the backhoe, only problem is there is no power on the 3 point. The arms just go down as low as they can and wont raise. You can raise by hand and they just...