help

I am going to wire some auxiliary lights, and solenoid driven diverter valves. The wiring will be exposed to sun and weather. Is SJOOTW, or SOOTW a suitable wire? Or do you have better recommendations? And on wire sizing: How do you size wiring for LED lights? I sized wire for the tiny...

I have a great 2016 2555 with 250 hours. I am looking for a backhoe for this machine. OEM at the time of manufacturing was a Model 75. Of course none of those around. Curious if any owners have any luck with aftermarkets on this tractor understanding if it doesn't match the subframe it...

I have an old Howard Rotavator Selectatilth that is missing the pto shaft and slip clutch. Does anyone know where I could find one? The shaft coming out of the gear box is 1.5" and has 10 splines. Also if anyone know what model this is that would help. The factory tag is missing. There is a...

I've got a little 25 hp chinesium tractor. So no real formal specs to toss around. I rebuild this thing new last summer. All new internals and seals. The sleeves are wet press in with two 4mm thick orings as seals on the bottom of the sleeves. Seals off the coolant from the oil sump. I...

Hi, I have a f16d tractor was using it today and switched between reverse and 2nd and it kept going backwards. If it try to put it in 1 or 3 it will stall out if i out in the 2nd spot stays reverse. Is there a linkage between the pin the shift moves and a gear somwhere? Any help sith a...

help looking for Mitsubishi k3d piston rings .75 for toro part number 72-4230 45fmj Tom

Back story on tractor is I did a rebuild on it new pistons, rings, rod bearings and head gasket. Flushed radiator new thermostat adjusted valves. I got it back together and it will start but it just seems like it has no power and I’m pretty sure it’s getting to hot also it won’t idle has to be...

What is the correct oil to use in my 25 year old 19hp, twin cyl, air cooled Generac generator. This is from the old days with higher ZDDP in the oil and I don't want to screw up my house generator with modern oil. The generator has test run more than actual use and only has maybe 15 hours of...

Looking at picking this up at auction. Anyone have any idea what is happening in reverse on this video? Do you hear that 'grinding'? Check it out around 18 seconds mark. Thanks!

Hello, have a Mahindra 5010. Noticed hydraulic oil around the edge of the rim, one wheel much worse than the other. How does that happen? Would it be common for there to be an axle seal and it's gone bad and is leaking? I think this is a 2014 model, would it be unusual to have a seal go out in...

2016 6.6 Duramax is I'll attempt to make this quick January drove truck 500 + miles to visit my dad, idler pulley and tensioner went out far from home got truck towed to a GM garage only place up there I could find that would touch a modern Diesel. Stubbornly figured since it's in might as well...

Hello.i have a mf65 tractor.one rear wheel rusted broke and destroyed the tire and intertube.the outer ring is broken.i just got the the tractor.its my first.can anyone tell me what other wheels I could use on it? Any help is greatly appreciated

When I had my Ford 5000, I made a tooth bar out of a 6x6x5/8 angle iron, I used a grinder and cut off wheel to make the teeth on both edges. It slipped over the bottom lip of the bucket, and straps around bucket held it on. So I had teeth to the front and down under the bucket I used it to...

hello all, any help would be appreciated. i needed to start my tratcor in about 28 degrees f. I have never had a problem with this tractor, but i don't run it much in snow/winter at all, a few times. i heated the glow plug(s)? not sure how many, its a 3 cylinder diesel mitsubishi i believe. it...

I am helping a friend dispose of her deceased father's garden and farming equipment. She is going through his stuff and trying to decide on what to keep, what to throw out and what can be useful to someone else to sell. Can anyone help ID this part and whether it comes from a lawn tractor...

The tractor has been sitting all winter, and now it won't turn over. The solenoid gives a loud clunk, but that is all I get. No hint of a starter problem before this. The battery is good at 12.7V at the starter. Tried shorting across the posts on the starter, and got nothing, so I'm thinking the...

i cant find what this part is in the mahindra catalog it just shows a square hole where this goes on the center case. my haudralics drained out of it. like a plug was released, not under pressure. it is on a 2015 gear series. thanks

I have a leak on the plate on my power steering pump on my 2120. The seal kit is $185. Cheapest I can find. I can get a new pump for just a little bit more. Anyone know a cheaper way to get this seal? It's an odd shaped seal so idk if a hydraulic shop could come up with one. Or if I'm gonna...

Hey team, this is my first post here. I hope I can get some illuminating responses. My in-laws have a Kioti KL401 (is that the real model# or is that just the loader) that's been sitting quite a while. I told them I'd take it off their hands and they said OK. I can't seem to find the year...

Power steering pump is leaking between the rear plate and the housing. The seal kits are discontinued. And it's an odd shaped seal. Any chance some good rtv on the flat bit will work? I have attached pics of where it's leaking in the yellow circle and a pic of the plate off and the seal.

I’ve been talking myself into a front mounted brush cutter and exploring some options. One thing I’ve noticed is a couple of the manufacturers may not be using a cushion valve on the motor, rather just teeing the lines. One side of my brain says that can’t work very well, the other side says but...

Has anyone sourced clutch friction disks for the shuttel shift transmission on these chinese dozers? I've been told to call a couple different companies with no success. Seems like nobody can get them. Just wondering if anybody has actually ordered them through a company and got them in hand or...

Here's the story I found out a few days ago that my fuel gauge isn't working. Ran out of fuel. Filled it up, bled the fuel lines by cracking the bolt on the fuel injection pump and it cranked right up. Next morning it cranked right up and I ran it again for several hours with no problem...

I have a Kubota MX5200. I have to questions. I bought a Titian 1912 rotary cutter. It has a single hydraulic hose for operation. I do not have rear remotes and just plan on mounting a single hydraulic control valve. There are some many options it has become confusing. What spool do I need and do...

I am searching for parts for a McCormick CT-41 (R-41) compact tractor. Front bearing and seal is out and need replacement. I have had no luck and our surrounding area has not heard of this tractor. Please help.

BLUF: Does anyone have CAD files of the buckets on the DL95 or CB65? Or can I get the pin sizes and spacing for each bucket? I don‘t have access to my tractor to measure it myself. I moved to S.Korea for a few years on an assignment and am separated from my GC1710. The onset of withdrawals...

Hi there, I am trying to help my landlord to get his tractor functioning properly. It was started by hot wiring in the past and I am trying to get it back to starting with a key. I believe the clutch safety was bypassed but am not able to locate it. Can anyone point me in the right direction to...

Hello everybody! I want to ask a piece of advice regarding an issue i have with the handlebar i have on my Grillo G110... As you can see in the photos + video below, it has a lot of slack where the handlebar connects with the bracket that holds it... I'm afraid it might break... What would you...

Good day We recently bought a secondhand Massey Ferguson 165 tractor (year and hours unknown). The tractor is fitted with a MK2 hydraulic pump. The lift or pump however do have so issues. When we try to hook and pickup/lift heavy implement (slasher) the tractor does not want to lift the...

I got this Tractor as a barn find only 85 hours. It hasn’t been turned on in years. When I go to turn it on all it does is crank. I emptied all the fuel out of it and replaced it with new. Still does the same thing. All the fluids are full. I pulled off the injector lines and they had fuel but...