john deere 2520

Had some close calls in the last few years using the forks w/ FEL handling wood. A few branches snuck past the factory guard and dented up the grille. Was able to bend back though; that's a $450 part! So had some time this winter to model up a design on CAD adding reinforcement to the factory...

Anyone have issues with the gearbox on they're deere mower deck? Gearbox model AM136330 Mistakenly I missed an oil leak/seal failure. Thus destroying the bearings. Well this gave me a project that surprisingly ended well. I removed the seals and began dismantling the gearbox. Deere...

Need help determining why all of a sudden there is no hydraulic pressure when I try to back blade with the 200CX loader mounted on my JD 2520 tractor. Bought the tractor new about 12 years ago and it has always worked fine. The hydraulic fluid is full and has been changed as recommended. The...

I have a John Deere 2520 that I had to remove the charge pump and valve block to replace the transmission input driveshaft that couples to the engine due to the end of it breaking off after the tractor tunnel section cracked due to rolling over. I very carefully and cleanly reassembled the pumps...

Hi all, Got a question. I have a John Deere 2520 with 4 hydraulic couplers for the FEL. Now I want to use a trailer with lifting cilinder. That one has only one hose and it drops by gravity. Are the Fell couples able to handle the retour? The Fell couplers are grouped in 2 x 2 for up and down...

My 2520 lost steering suddenly without any evidence of any other problems. No hydraulic leaks, levels are up, hydraulic steering rod intact, tie rod etc.. I suspect the steering valve at the base of the steering column, the steering wheel rotates either direction continuously with only minor...

I was very disappointed with the stock deere 54" snowplow. So I set out to adapt a Meyer's 8ft plow. The plow was old and pretty rough. Challenge accepted.

ive been looking at a previous post on this subject. basically the tractor starts , then immediately shuts down. from my research, its one of three things, 1 the fuel solenoid. 2 the v4 diode. 3 the signal to the solenoid. i have a test light. i disconnected the wiring to the solenoid. there are...

Anyone have a source of wiring diagram for ten year old JD 2520 ? Don’t want to go into details but it has to do with the starting system. Paid dealer over two grand a couple months ago and only got a temporary fix. I live on a one dealer island so have no other option. I’m good at...

Hi there, Am hoping some of you JD owners can help me please. I'm in the process of getting some adapters machined to allow me to fit some turf rims originally from a JD 2520 to my Yanmar AF120, as its the easiest way to get some cheap turf rims on that machine. I have the rims but am having...

Morning I do my own maintenance & tractor manual says it痴 time to check the valve clearance. Thinking of having a local mechanic do it. Questions - directions on-line somewhere or do I need to get sheet from dealer? Hard/time involved? Thanks

I keep having this problem with my 3-point hitch. It goes up-down no problem. I don't use it for a few months and then it's stuck in the up position. Nothing changed - I didn't touch the adjustment knob at any point. I pulled the plastic covers off the area under the seat. I also pulled the...

2520 died last week while backing a trailer, checked fuses, pulled fuel solenoid and tractor starts and runs fine but have to shut off by reaching into solenoid area to shut off. Sounds like the holding circuit is not working, took dash apart but not seeing the diodes that are discussed in other...

Using rear cutter the other day and noticed a noise coming from engine. Lowered the RPM and disengaged the PTO to investigate an noticed smoke coming from hydraulic pump. Reved up the RPMs and noticed noise again. Went to drive tractor to garage and 3-pt wouldn't lift. Once in garage, I...

2011 JD 2520 I was out tilling today, going along no problems and the tractor just died. When I turn the key on, nothing on the dash comes on. No glow plug light. No fuel pump noise. Fuses are all fine. Battery is good - just replaced last fall, all the connections are clean and tight...

2009 JD2520....start...run ... Dies....hard to restart...restarts....runs...dies....tractor sits a couple days....starts right up...work it an hour...dies...hard to restart...runs 30 minutes...dies....hard restart...20 seconds it dies...o replaced fuel,oil and both air filters ( owner hadn't...

I have set of R4 tires and rims for a John Deere 2520 or 2720 Compact tractor. They only have 14 hrs on them and are in great shape. Asking $800 or best offer. Located in Spokane, Washington. Mark

I'm new here and I'm sure its been done before. I'd like to build a winter cab. Anyone have pictures of a completed cab. I have a good idea of the shape and materials needed.

I have a John Deere 2520 with an electrical problem in the starting circuit. Getting voltage through the ignition switch but died suddenly and won't start. Lights work but that's it. Hoping someone can point me in the right direction. Does anyone have a description of the starting circuit or...

thanks all for the invaluable info you guys post on Kubotas and JD's. Extremely helpful stuff!

I traded for a used 2008 JD2520 in 2012 when it had about 300 hours on it. The dealer had recently changed hydraulic fluid and coolant. I’ve kept up with oil changes and lubricants. I am now coming up on the 500 hour service mark and was wondering what else I should be checking ... Frank

To my fellow TBN problem solvers ... Background: Yesterday the 3 point was operating normally except for somewhat limited lift height because of a bent (twisted) bracket (Item B, page 60-35-2 of JD2520 Technical Manual). This bracket attaches the depth control handle to the rockshaft eccentric...

I am considering trading ( or selling outright ) my low hours ( 645 ) very clean JD790 / ags / power beyond/ gear / 419FEL in on a 2520 with 775 hours / hydro / FEL / 54SB snow blower. I would be interested in thoughts advice etc the 790 I moved snow and brush hogged the field twice a year and...

Hello everyone. I recently inherited the maintenance duties on my parents property after my dad past away. He had a Deere 2520 and an old Ford 8n (or 9n not sure). Anyway, the ford is not running and has a Howse 500 brush hog attached to it. I was wondering if I can hook this up to the Deere...

Hi All, Traded my 4410 with a fellow for his 2520 a couple of years ago - the 4410 was simply too big for my new house/property. So, here I am moving again ... had to buy temp house and there is no room for even the 2520. Rig has less than 100 hours - mostly doing landscaping on my place and...

hi, would you buy a 2011 JD2520 with 2600 hours and no FEL or MMM for $6000. i was thinking of getting it and buying an H130 FEL ($4000) to mount on it. that makes it $10k. run it till it drops and then either repower it with a new yanmar engine or upgrade to a 2025R or 2032R and move the FEL...

hi, i found a 2011 JD2520 i am interested in. 2600 hours. tractor only. what would be an approx value/price? also, says a 200cx loader fits. are those still available or what after market loader might fit it? and possibly a backhoe? thanks

I did my second transmission fluid change yesterday and couldn't get the 4 magnets in the suction screen to stick to the housing, they would all just clump together without any attraction to the screen. I remember the first change, they were all laying separated and against the screen when I...

Had an intermintant leak where would see a couple drops under the front of the tractor on occassion, didn't always happen. Couldn't really see where it was coming from, made sure everything was tight and just kept an eye on coolant levels. All winter for snow plowing never noticed it, but last...

I needed to remove two septic tank 5 ft. lids. I borrowed a boom pole hoping to remove them with my JD2520. No dice. The lids were too heavy. They wouldn't budge an inch. I have a 9.5k winch and knew the winch wouldn't have a problem lifting them. So I came up with this. I used 2x2x1/4...

I have a JD 2520 tractor with a JD46 backhoe and need to switch the rear mount for the 3 point hitch and the rear mount for the backhoe a few times each year. When I installed the backhoe mount this summer I discovered one the threaded bolt holes that holds the mount to the tractor was...

So, while mowing today the 2520 went out of gear. Switching from High to Low made no difference. No movement occurs in either direction. Hydro level is fine, and all PTOs work fine. Any clue? No grinding or anything prior to this. Is there a switch somewhere or something electrical that...

Hey y'all, Does anybody know, if a JD 2520 "Hi-Crop" uses a special Top-Link or the same, as any other 2520?

I have just 70 hrs (from new) on a 2520 .. some of which was expended while plowing with a blower attached... and the mower belt self destructed. Not too eventful but was pretty tough to cut grass! Local JD dealer sold me one for $120 (+/-) Canadian. I whined about the low hours but to no avail...

When I took my JD front mounted 47" snow blower off my 2520 for the winter today and put my JD 46 backhoe on I was reminded how much of a pita mounting the backhoe is. The JD dealer claims you can not mount the front snow blower on a 2520 with the 46 backhoe mounted and they are probably right...

hello i just purchased a 2008 2520 and on a cold start the glow plug light (or pre heater light) only stays on for a second or less but the ticking sound from the engine keeps ticking as long as I have the key in the "on" position the ticking wont stop. when I start the tractor it runs Very...

Hello, This is my first post and I come to you in the middle of a blizzard with a problem . Our John Deere 2520 bucket will not lift. It will curl and drop but not lift. You can hear the SCV put a load on the engine when you pull the lift bar back but it does nothing. Any clues on how to fix it?

Hi all, I have a 2007 JD 2520 that has 420 hrs on it that has been working perfectly for my light duty work on my 2.5 acres. Recently I am having a problem with the tach and wanted to know if anyone has experienced a similar problem and hopefully can recommend a fix. Every now and then, the...

Hi Folks, I have a John Deere 2520 that I have installed a power beyond in order to use my Bradco trencher. The trencher has a Metro valve that is behaving as a closed center valve when I really think I need an open center valve. I was hoping that with a few details and pictures, I can get...

Anyone else have a leak where this shaft goes into the transmission? If so, is this seal easily replaced? Not a gushing leak but always has drops on the floor when sitting overnight. My tractor is a 2011 model. Thanks.

Found a JD 2520 for sale and have questions about its prior care. Built in 2008, total time 369 hours. Last oil change was in 2009 with 109 hours with nothing since. So, with 260 hours and 6 years since last oil change, what should I look for? Engine is filthy, coated with lime. Been used to cut...

I just purchased a 72" mid mount mower for my 2520. It came with the mechanical lift to install it on the tractor. I purchased the tractor used off of a dealer a few months ago and it came with a loader and backhoe already installed. When I removed the backhoe so that I could install the mower...

Hi all, i currently own a Deere X495 with the 62C deck and would like to upgrade to something bigger, although 70% of the time will be mowing about 1.5 acres of lawn. I have my eyes set on two offers in my region (both used tractor dealers). One is a Deere 2520 with the 62D deck and 1750 hours...

Has anyone replaced the three point hitch stabilizers on their john Deere with the ones like I have seen on the kubotas. I am sure that I have read somewhere on here but I did a search on here and Google I can't seem to find anything. The turnbuckles are a royal pain and I would love to be able...

Owners of 2520 with 72" mmm, which front hanger? I have a 2012 JD 2520 with a 72" mid-mount mower. When the deck is raised to the full up position, the draft arm rubs on the differential housing. This has caused significant wear to both the draft bar and differential housing. The dealer could...

Yesterday I purchased a 2010 John Deere 2520 that came already equipped with a loader and backhoe. However, it did not come with a mower. I was wondering if anyone knew what all it would take to install a MMM either 60" or 72" on it and an idea of how much it would cost? Also, if anyone knows of...

Hi Everyone, Looking for some opinions. I went to my local dealer looking at the 2032r's. Worked out to be more than I wanted to spend. He showed me a 2009 2520 they just took in. It has 100 hours. Looks brand new, 200cx loader, 62d deck with independent hydraulic lift and diverter. Ballast...

I have a 2008 2520 that I use for plowing snow. My drive is 600 feet with 150 being asphalt and the remainder stone. Currently I'm plowing this with a FEL and 4 foot 3 point hitch blade. I'm thinking its time to take it to the next level and I welcome your suggestions / opinions. I believe...

A brand new jd 2520, 2013 leftover. Warranty starts when I buy it. Tractor, loader/bucket and frontier box blade for $16,300 What do you guys think? Or a yanmar 424, brand new 2015 with loader/bucket and woods box blade for $15,300

Hello, I've been lurking and reading but decided I need to sign up and ask some questions. I have narrowed it down to two tractors. A brand new left over 2013 john deere 2520 with loader/bucket and frontier box blade for $16,300 2 year bumper to bumper and 4 year power train, dealer is 20 min...

Snow Storm Today Snowblowing with the John Deere 2520 & Bigtoolrack for Counterweight Well we did not get what was expected today but I thought I would post this video of the clean up.... Looks like about 8 to 10 inches in Northwest Connecticut with some drifting.....

HI, I have jd 2006 yr. 2520cut 4wd with about 800 hrs., on it has anybody ever did john deere's upgrade to their spindle and bottom cases according to dtac on the parts breakdown? my left side was leaking pretty bad and I had replaced bottom seal's & bearing's last year and only lasted about 50...

I went to my three closest dealers (JD, Mahindra, Kioti) and told them I could pay max $20K cash for a machine and that I wanted the most tractor / loader I could get for that price. The three tractors I was shown were as follows: Kioti DS4510HS - a 45 hp gear tractor with hyraulic shuttle and...

I hooked up my snowblower a few weeks ago and noticed that it is always spinning, even with the pto switch in the off position. This is the first pto attachment I have used since the rototiller in the late summer, so I am a little unsure how long this has been an issue. When I first start the...

The JD2520 has an open system, not a closed transmisision like in a car (ie., if you have any attachments on the tractor such as FEL & quick hitch when changing the tranny oil) then you will certainly need more than 2.6 gal recommended. It will take close to 4 gal of oil or more. Everyone who...

Good evening.. My apologies if this isn't the correct place for this or if it's already been asked.. I looked but didn't see the exact problem.. So here goes.. This problem also happened a month ago or so and has since resolved itself.. I stopped the tractor today after mowing for about a half...

So I just got a Good deal on a complete set front and rear R3 Turf tires and wheels for my JD2520 in Mint condition for $800. I have Loaded R4s and was wondering if anyone has some tips on removing the Heavy loaded R4s. Thanks By the way how heavy do you think they are my guess is 300#

I purchased/ordered my JD 2520 Utility when they first came out. Can't remember the year. Tractor has 380 hours on it with few problems. My battery was original and I replaced it this fall because the battery light started coming on. I figured probably the battery because it was several years...

I bought a "service" kit from the dealer so I could do my 200 hour service on my Deere 2520. Changed the hydro oil, new filter, cleaned the suction screen (very, very clean this time around), changed the engine oil (doesn't appear to use any oil) and filter, installed a new primary air filter...

My yellow PTO knob will not stay out when I pull it out to turn it on. It will continue to run if I hold the knob out, but shuts off when I let go. Do I need to replace the entire knob assembly? Is it safe to force it to stay out so I can finish the job I am doing until I can get it fixed?

Hello, I am buying lights for my hood guard and am going to be using clamp mounts. Since my tractor is in my barn up in northern Michigan I need to know what size the tubing is on the tob bar of te hood gaurd. could someone measure it and let me know? I think it is about 1 1/4, but cannot...

I've been looking but can't find the answer. I doubt if there is much but need to know before I decide.

I'm looking for a nice 72" MMM for my JD 2520. If you have one or know of one, please contact me. Thank you!:drink:

I'm looking to find a nice 72 inch MMM for my JD 2520. Can I put a 7 IRON 72 inch MMM under it? Or can I only run the lighter version of the 72 inch MMM? I found a nice 7 IRON MMM and would buy it if fits my 2520, but if it won't fit I will look for a lighter 72. If indeed I do need the...

My 2520 has a real sloppy feel to its FEL Handle. Its not a huge deal, but its annoying when you try and do precision work with it because you need to move it past all the "slop" before it starts activating the next control. The handle on mine slops mostly side to side in the curling...

I think I have narrowed down my search and it is between those two. I will first explain what I want to do. I will be mowing about 3 acres all the time. I will also use the tractor to haul firewood, pull trees, remove small stumps/shrubs, clear buckthorn, drag driveway, plow snow, maybe post...

I have read several threads via searching about adding 12 volt plugs. Alot of them talk about the location. I need to know if the bundle of wires behind the seat can be used to make this easy. I know where I want to locate it so that is not my issue. Basically, what is the easiest way to...

Does anyone have a good idea where I could find a chrome extension to put on my exhaust to get it up and over my head??? I have a 2520 john deere, I am looking to curve it at the current pipe and go up from there. I do not want to put any holes in my hood.

Hi all. I remember seeing somewhere where someone had mounted fenders over the front tires of his 2520. I can't find it now but was wondering if anyone has done it and if so if you could post some pics and tell me how. I have had two nice little plastic fenders for a year and a half that fit...

Hi All, I'm in the market for a CUT and will be heading out this weekend to look at a 2008 JD2520 with 200CX FEL, MMM (not sure on size), Frontier RT1150 Tiller and 4' Forks. ~ 100 hrs., pictures look clean and owner indicates tractor was garaged. Asking price is $16250. It seems in line with...

Went to use my tractor this morning the " joystick " was very stiff to move and the FEL would not raise up, hydraulic fluid appears to be ok in the sight glass. It was working fine when I parked the tractor the day before. The rear three point works fine as the snow blower would raise and lower...

Just finished my snowplow project. I have a deere 2520 outfitted with a 200cx loader. I purchased a used deere 375 blade assembly and cut the frame just behind where the cylinders are mounted. Welded a frame out of 4 inch C channel and 1/4 inch plate steel. Ordered quick attach loader parts...

Here's what I'm up against: I have a 2011 2520 that I bought new in 2011. It has the 200CX loader and 62D mower deck. It has 106 hours on it and all I've done maintenance wise is the 50 hour service. The manual doesn't call for another service until 200 hours but since I'm not racking up the...

Hi I'm new to the forum but am considering getting a used 2006 John Deere 2520. Based on other posts in the forum it seems the two major issues were the 3pt drag links rubbing the tires and front axle leaks. For the drag links I saw some posts saying it was covered under warranty. How can I know...

hello, I have a jd2520 scut that is having problems with the seals in my front hubs. I have looked on this forum +gtt to see if anyone else is having the same trouble this will be the 2rd time replaceing,its a2006 with 650hrs on it.i also see other owners had same problems with their fuel tanks...

Hello Tractor Lovers! My name is Jamie Jones. I'm 48 and live in New Hampshire with my wife (no kids). I love using forums to learn and share ideas - I go to mapletrader (I make syrup) and arborist (tree work) and have learned so much. Now I have a tractor and here I go again.... I've been...

I used the post hole digger earlier this summer and unmounted it when done, leaving the 3-point hitch all the way up. Spent the summer doing light odd jobs with the loader. So cleaning up the yard today I thought I'd move some implements around and noticed the 3-point hitch won't lower...

My neighbor has a JD 2520 which has a dealer installed independent (loader joystick controlled) mid-mount mower lift kit. It has worked well for 3+ years but now usual joystick movement to raise and lower the mower (similar to raise or lower loader arms) no longer works. If he connects the...

I'm looking to see if anyone has mounted and used a Woods BH70 backhoe on a John Deere 2520. Does Woods make a mounting frame for this combo and is the BH70 to big for the 2520? I found a BH70 used and its mounted on the bigger 3320.

Local dealer has this tractor Machine Finder Has 200cx loader, 62" belly mower and 47" front mounted snow blower for $17900. Good price? Looks to be pretty clean.

2011, JD 2520, with 105 hours, new loader, new mower deck, asking 17K . Tractor looks like new..Thinking of asking for price with backhoe??? Opinions??

I just finished mowing (about 4 hours) pulled the tractor in front of the barn to let it cool off. A couple hours later I went to start and it would not crank. I will do my best to describe what I'm hearing. When I turn the key it makes a loud sharp scraping sound. The sound seems to be coming...

I am running a 2011 JD 252. From time to time I see used rear snowblowers, but I am never sure my 2520 will power them properly. I wanted to ask JD 2520 owners about their snowblowers. The rated rear pto hp is 20.5hp. To cover my tires tracks I would need at minimum a 54", and to get a little...

Talking about the s-cuts of course. I used to have one of the first years out and am leaning towards going back to one as we're going to have more property to maintain shortly. My questions aren't what they'll do but if there have been any improvements since they were released (I believe...

The mower discharge guard was the first thing to come off. This is my third tractor I have removed it from.I haven't broke a window yet and no neighbors to worry about. I noticed the hydraulic line keeper above the mower was missing the day I picked it up. Dealer is getting me one soon. After...

Finally ready to upgrade in size from my Subcompact tractor. Looking for something the size of the Kubota B series/ JD 2000 series. Eliminated the Kubota as the nearest dealer is too far away. Decided on the JD2520. Went to the very major John Deere dealer nearby and organised for them to...

We have a Deere 2520 tractor with mod mount mowing deck . Just bought a 200cX loader. We removed the loader to mow the lawn for the first time. We attached the hydraulics but we cannot lower the mowing deck to mow. Is there some sort of lock that is holding the mowing deck up to keep it from...

Hello, I was looking at the JD 2520 and was wondering for comparison, what is the comparable size in the Kubota series? Thank you

i went to go buy a JD 2520 TBL the other day but they didnt have one on hand. sounds like the are discontinuing it . *What is gonna be the next generation of that tractor?* For the TBL with power beyond and install charges after all said and done i was quoted $23,900 the 2320 looks good...

I had something weird happen today to my 2520. I noticed that during a throttle up it kinda hesitated bucked...some smoke and then went to the set RPM. It has never done this before. It has 178hours on it so far. I checked the seddiment bowl and it was pretty dirty. I cleaned it all out...

Hello, I'm trying to put the two lift lines on and it appears over the winter the hydraulic must have settled in the cylinders creating pressure at the end and now I cannot get the lines on. The bucket tilt lines went right on. I remember reading this issue on here before and thinking I never...

I know a guy that has a 2520. It starts and runs fine but the engine pre-heater light stays on. The light goes off when you speed the engine up, but comes back on when you idle back down. Any suggestions of what it might be? Thanks.

was at jd dealer picking up some parts. and I asked about getting a 2520 he said they are going to quit making it, but would sell me a 2720 for about the same price.he was going to work up a qoute and get back to me. must going to come with a new model .have you guys heard any gossip on this?

Hi bought my second john deere went from 2305 to a 2520 because of my ex. hmmm thanx i think i forgot to thank her. i have pallet forks, waiting on a 54" box blade thru everything attachments. Plan on making a a tnt for the 3 point hitch i picked up one cylinder already.have a mechanical...

Hello everyone! I am a really new poster but come here often for advice and help. I own a 2007 John Deere 2520 with 400 hours and I am having trouble with the power assist steering. When the tractor is running the charge pump is whining and the power steering does not work. I have changed...

Had my new Deere 2520 delievered yesterday....just in time too! Got about 4 or 5 inches of snow today. Took the MMM off this morning and went at the driveway with the FEL. I gotta tell you, this was fun. The machine is very impressive. Managed to clear my 200 yd paved driveway in no time...

Does anyone have any idea why the wet brakes on my 2520 make a loud high pitch squeal? Both sides will do it and it seems to go away if I ride the brakes lightly for 10-20ft. It will come right back after a few minutes though. I changed the transmission fluid/filter at 50 hrs with hygard low...

Still looking for wiring diagram for a 2006+ JD 2520 with a Yanmar engine. Bought the manual from a JD dealer and got the manual for PRE 2006 machine. JD in its wisdom have used the sam model nmber for VERY different machines. Dealer was given serial #. Anyway...help in the wiring schematic...

I have several large fields of bet. 3 and 5 acres that require occasional mowing. In the past a local farmer would mow for hay, but with his herd reduced in size no longer has need for it. I do have a 4 ft. rotary mower that works well but takes forever and a day. Plus it's a rough cut, and...

Hi all Yup I am new to the forum and glad to see one out there for tractors. I just got my 2008 2520 last month and of course am loving it. I have been using one at work for a couple years (thats why I got it) so am familiar with the operation and tractor, just need some help with the...

I want to use my JD 2520CUT to operate a land pride overseeeder os1548. Does anyone know if the tractor can lift it? THe tractor specs say it can lift #1,250 and the overseeder weights #1,250-#1,290. Any other tips to operating the overrseeder are appreciated! I am new to tractors and have...

My first brand new to me JD. It's a leftover 2010.Came with a grader blade and finish mower. 27 hours on it now. I'm impressed with the power this tractor has. Any tips on maintaining, operation, problems you guys have had?

I have seen on this forum that others have had the 2 year battery issue. Lately when I would try to start my 2520 it would act like a dead battery but would try to start. I would keep trying and once it would turn over it would start the tractor. Once it started I could use it then shut it off...

Just ordered a tech manual from JD to get a wiring diagram ( start/fuel circuits ) - but does anyone here have one for a JD 2520? Parts Department only has harness descriptions, service department was too busy (and slightly under pressure for others) to track it down, so off to a full blown...

Have about 10 hours on my new 2520. When I turn my key to the ON position, the manual says you will hear the "engine fuel shut-off soenoid engage with a click". I get a constant clicking sound, almost like a clock or more accurrately reminds me of when my started died on my car I got a...

I just bought a pj utility trailer 83" x 16' includes 2' beavertail to haul my 2520 and would like some input about how everyone secures their load. Pictures of a secured JD 2520 would be great. I am planning on chains on 4 corners with straps as backups as I always over secure if I can.

What trailer do you tow your JD 2520 with? I am thinking a 16' ( 14' w/2' dovetail ) would be fine for the tractor with loader and tiller based on measurements. Just not sure if it is long enough to adjust balance the load. Tractor with loader and 655 tiller should be around 3000#.

Looking to purchase my first tractor. JD 2520 with 200CX Loader with 53 inch bucket, and RC Rotary Cutter with slip clutch. Dealer's price is $19,980.00 plus tax. This includes any JD incentives, such as $500 off when you buy two attachments. With 10% down, I can get 0% financing for 48...

Any one had a problem with 3 point-hitch arms not raising or lowering? Have not had a problem in the past but now they seem to be just stuck!

Has anyone experienced their power steering cutting out while going up a steep hill with their JD 2520 CUT? I noticed that if I drive straight up a steep hill my power steering will cut out intermittently. The tractor has 52 hours on it and I have not exerienced this before yesterday. I had...

kinda decided on these two tractors I would appreciate anyone who has been looking at these two to let me know how you came to your decision. dealer suppoert is not an issue as they are 2 mi appart and both helpfull, both came in at almost the same price with loader and mmm mower the price is...

kinda decided between these two tractors anyone who was looking at these two what made up your mind saw the jd today definatly like the pedal arangement better prices are almost the same for fel and mmm and tractor dealer support isnt an issue as both were helpful and within 2 mi of each other...

Well I used the 2520 for about 1 hour today and was about to load a Rock into the bucket so I lowered the bucket turned off the tractor and when I went to start it again it would not start. The dash lights come on and the fuel pump clicks as normal but the starter does not turn over. I checked...

I am trying to decide which would be best fit for my JD2520 a RC 2048 or a RC 2060. I am leaning toward the RC 2048 any thoughts. You can get them with rubber front and metal rear guards or for extra cost chains front and rear. Which is better. Thanks

Hi All, I have a 2011 JD 2520. Following the 50 hour service I noticed a light "tick" noise coming from the front of the tractor. It is not a loud knock or lifter sound rather a soft intermittent "tick" which sounds like a old grandfather clock. I have tried to narrow it down but the best I can...

Hi everyone! I have a question on the JD 2520. If I were to purchase a 3 pt hitch generator does the 2520 have a governor that will maintain generator rpm's without having to constantly adjust the throttle lever due to changing loads on the generator? If it's a set it and leave it, I'm OK with...

I am considering a flail mower for my 2520 and I have been looking at Everything Attachments Phoenix SLE line. Does anybody have experience with this flail mower? The second question, what size should I get, I have 20.5 at the PTO, and I would like to get the 55" mower since it would be...

My JD 2520 is about due for the 50 hr. service, which includes changing the transmission oil. I never did this before and was curious about how much transmission oil I should expect to pour out of once the plug is removed? The owner's manual lists the transmission as holding a total of 3.9...

I have a JD2520 and I just purchased a Wallenstein BX42r chipper with the hydro power feed. Seems easy enough, I get a male and female connector and loop the power feed circuit through the power beyond. I talked to Wallenstein told them I had 5 GPM and a power beyond and they thought it would...

Ok I'm very close in pulling the trigger on a tractor. So here's my dilemma. I have 2.5 acres that I mow and have light front loader work around the place. I'll be building a storage barn next year and re-doing my landscaping around the house. Most (90%) of my tractor work will be mowing. I...

I'm looking at both these tractors and gotten prices on both. Kubota B2620 w/FEL, Turf Tires and 60in mower = $17450 John Deere 2520 w/FEL, Turf Tires and 62in mower = $20487 Both have 0% financing (Deere 48months/Kubota 60months) I've looked at the specs and both are very similar. On paper...

If you need a John Deere 2520 Mower Deck - $650 w/Ind lift & stow & go I came across a killer deal on Craigslist for anyone that lives in or close to Freeville NY and or is willing to drive to Freeville and is looking to add a 62D mower to there 2520. The deck also comes with the ind lift and...

When I purchased my property several years ago and well before I bought the tractor, I thought that a DR 4 1/2 inch chipper would be a good purchase. Well it is underpowered and the feed hole is square which can make feeding smaller branches difficult when the crook of the branch is spread...

Hello, More pricing or use advice please. I found a JD 2520 4WD, 200CX FEL, 180 hours, 2007 for $14,500. This seems like a reasonable tractor for us. Our place is 23 acres, most which is a field with some trees and brush. According to tractorhouse.com, this looks like a reasonable deal. The...

Hi all, So I'm a first time poster...read some threads thus far and decided to post a question. The 2520 is my dads tractor (just bought) and I know he wants a snow plow blade for it, only thing is they are pretty costly new and hard to come by used. So I was looking at some cheap options...

After waiting 2 months, I finally got my new 2520 this weekend. It has the 200cx loader w/61" bucket and 46 backhoe. Put about 3 hrs on it so far, mostly "feeling" it out and learning to use the backhoe. It is my first tractor, so I really have no reference to compare it to. Plan on getting...

Good day all. I have the 2520 with the 200cx. With the quick detach of the bucket, are there any other attachments that will fit? someone told me last week that the mounting system was universal and many brands would fit. I just want to make sure before I start to scout the internet and get...

About 2 weeks ago, we took delivery on our 2011 2520. Like many others here, we took advantage of the $2500 promotion and signed the papers on May 31. The 2520 was on the lot and if it had not been there when I stopped a week prior, I doubt we would have considered purchasing a different tractor...

I have a JD 2520 almost ready for delivery in a few weeks. I was wondering if there are any special tools or "time saving" tools you would recommend to have on hand that will make owning this tractor easier. I have a full complement of standard mechanics type tools, but will certainly pick up...

This was my first endeavor into the loader/bh world. Hopefully I made a good choice. Any tips, hints, suggestions on using (rpm with bh) would be appreciated.

I have been monitoring the forums for a while but this is my first post. I have a 10 acre property that has about three acres of mowing. I use a Deere x304 for this job as there are many trees to get around, works great. I want to maintain the remainder of the property (rolling terrain in...

Having put a few hours on my tractor I thought I would look at the grease fittings for the first time. So I pulled out the manual and only found 3 zirk fittings listed.:( This didnt seem right so I started to look around and here is what I found. 3 listed in the manaul for the front suspension...

After a long search I found a good tractor. Went to a dealer (180 miles away) and was looking at a 2001 4300 with FEL and 72" deck. Boy it was rough... But as I was leaving I saw a JD 2520 and I was like..."aww thats a new one, no thanks" but the dealer said it actually wasn't. It was a...

Okay, we're in the middle of summer, but I'm already thinking about winter. I just purchased a new JD 2520 with a 61" FEL, R4 tires (no filled tires), ballast box and I'm interested in hearing about other folks experience and recommendations on snow removal. I have a 400' long steep driveway...

We are to take delivery of our new 2520 in the next week or 2 (waiting on arrival of FEL). Unlike many others, the dealer I stopped by had one on the lot. Whereas I have no reason to doubt the information the dealer provided me, is there a way I can determine the date of manufacture by looking...

Found this on craiglist http://kansascity.craigslist.org/grd/2436252883.html

Hi, everybody. New member, but have been checking out TBN for some time. I ordered a new John Deere 2520 w/200cx loader and BH46 backhoe a couple weeks ago. I have a tentative delivery date of August 3. I'm going mad waiting for it. I have 2.5 acres of yard/woods/driveway and it's intended...

I just bought a new Explorer on Saturday with the tow package which includes the class III hitch rated to 5000lbs, transmission cooler and a larger radiator. If I bought an 18' Aluma tandem trailer it would weight 1100 lbs, my JD2520 with BH weights about 3500 lbs. This should leave me with...

I finally made a decision and purchased the 2520! 200CX FEL, 62DMMM, Wood Box Blade, I-Match, 46 Backhoe(when it arrives), 54" snowblower! I spent alot of time on TBN looking at various topics. Thank you to all of you that have made vairious posts. The incentives by JD, 0% for 72 months and...

Just posting to introduce myself. I just joined and took delivery of my John Deere 2520 with the 62D MMM and 200CX FEL. I look forward to learning about my new unit from you all. BTW, who do you use to source tractor accessories at reasonable prices? For now, I'm thinking about a light kit...

I am considering buying a John Deere 2520. The transmission has a high and low range (no mid range). I will be getting a 62D mid mount mower as well. My question is whether I can mow at a reasonable speed in high range ....or do I need to be in low range for the power when mowing. I have...

Has anyone installed the JD 3rd SCV valve kit (LVB25927) and the power beyond kit (LVB25603) on their 2520? I would like to add a small grapple or thumb to my FEL.

Hi everyone ... I'm a newbie who is amazed at the knowledge floating around on this site. I'm hoping some of you can help with a few questions I have. I just bought 9 acres - 7 acres of timber, 2 acres of grass, 600' gravel driveway. My primary activities will be clearing timber, removing snow...

I was looking at tractors last week and my local Deere dealer said there will be no changes to the 2520/2720 series. I thought there was going to be some subtle changes and a new numbering of these models? I figured this was the reason he was trying to sell me a 2720 for $17, 100 he had on...

I bought a Countyline (SpeeCo) PHD with the 12" auger from TSC for my JD2520. I raise the 3ph up until the PHD arm touches the back of the tractor but the auger doesn't clear the ground. Any suggestions on how to configure the PHD and/or 3ph to get it to work? Thanks!

Does anyone have this setup a JD2520 with a jd655 tiller. I am about to get the 655 and want to hear from some that have this setup so I will be sure this is the right setup or should I go with the jd647. I measured the rear R4's tread and it is 49 inches wide so the 647 should cove all but one...

Brand New - To Forum and New JD 2520 Receiving John Deere 2520, 200CX Loader, RT1157 Tiller, BB2060 Box Blade and Bush Hog Auger first thing in the morning. Looking for comments and suggestions.

I was clearing brush for a new neighbor with my 2520 (160 hours) when I heard a pop and gushing sound. I shut down the tractor and checked out the back, where I found hydraulic fluid gushing from the right axle hub, the right wheel no longer perpendicular to the axle centerline, and black...

What is a good price, they said $20,000 for 2520 and loader, I offered $19,000. What are others getting them for. Wayne

This will probably be the last thread before I decide to purchase a jd 2520 with a 200cx and 62D MMM. Also the tractor will have wheel wieghts and a BB. What does everyone use their 2520 for. I plan to use it for mowing, plowing, small scale logging for firewood and in the futer when I get a BH...

I recently acquired a 2520 with a FEL and rear blade. As spring is just around the corner (previous snows have melted so hopefully no more), I am contemplating my next attachment - a PTO wood chipper. My property is heavily wooded and I can use this year round for fallen branches and the like...

started pricing the JD 2520 because of the quick change bucket (FEL) and other quick attach implements, tractor with R4, 62" MMM, 200CX loader is $18,500 (before any taxes). Then of course I had to look at Kubota (have owned two), so I priced B2920, FEL, 60" MMM and was at $18,500, then looked...

I just got a quote yesterday for a new 2520, 200cx fel with 53" bucket and hood guard, and 62D mmm with independent lift - no addition hydraulics as I plan on adding my own. Dealer quoted $19,100 out the door. What do you think on this price?

Hello to the group, this is my first post. I will be pulling the trigger next week on a new tractor. I have done a lot of reading and comparing stats. It痴 down to two tractors?D 2520 and Kubota B2920. Both with FEL and BH. I have ten acres, about 6 in gentle sloping pasture and 4 wooded...

Santa came early this year and so did the snow. The weatherman was calling for some much nicer weather than this. Anyway, I got the tractor with the 200CX Loader, the 46 Backhoe, the 54" Blade and the BB1060 box blade. I can't wait to start some of the projects I have planned for this toy, uh...

I just tried the tractor in the snow for the first time and the front wheels spin and slide on the smallest incline. I have R4's rears are loaded and they were fine. I was pushing a small amount of snow on a grassy area using 4 wd no traction in the front. I ordered and received chains for the...

I recently purchased a new 2010 JD2520. I have read the owners manual regarding the startup procedure, but it really doesn't address my question. In the warmer weather, I just turned the key right over to the cranking position and away she went with just a few turns of the starter. Now in the...

Sorry.....should have posted this on the "Owning and Operating" section. I moved it. REV

I was recently quoted a little over 23000.00 for this combination....thing is, they figured the tractor at the same price I was quoted a couple of months ago while I was trying to narrow down a choice.Well....this week they have signs all along the highway, touting "Big Sale" "Huge Savings"...

Bought a used. 2007, JD 2520 with 84 hours on the clock, back in early September. Put a Curtis hard side cab, heat, work lights, radio, beacon light in the cab. Put everything in myself with no help, except, I did have the dealer put in the heat. Just thought I would share a few pics...

I don't recall what thread it was in but someone relocated their seat belt buckle holders due to a hydraulic valve project they were doing. I liked the looks of where they put them so I moved mine also. You know...I can see myself buckling up now that they are out there visible and easy to...

I am real close to purchasing the JD 2520 with loader, backhoe, blade and box blade. The dealer worked up the quote in MSRP which I verified, then discounted it by a little over 12%. That seems good to me but there is also a charge for 12 hours of prep. Is this normal or should the prep be...

Received a price of $14,700 on a new JD2520 tractor, Plus $2770 for front end loader (CX200), and $6,390 for JD #46 backhoe. I would be trading in my 2007 JD2305 (110 hrs.) , with CX200 loader and JD#260 backhoe for a total of $13,160. The total for the new JD 2520, with loader and backhoe...

I have 10 acres, finish mow about 2 acres, "rough mow" about 3 acres, garden of 2 acres. I have a Case 530 ag tractor i use for fall plowing, discing, prepping garden. Had a JD317 lawnmower but that is getting pretty worn. Will keep the ag tractor, looking for something to mow, landscape and...

This is a first for me. So I guess I am a wanna-bee farmer. There are Avo groves all around and my 'great' brush & scrub oak landscape. I am now retired with a JD 2520 with just 10 hrs and it is awesome! I have a hilly 4 acres & brush so going up/down SLOWLY ... is a bit of a challenge. My...

Hello! First post. I am leaning towards purchasing a JD 2520. Where is this tractor made? Thank you.

Just ordered a JD 2520 today to replace my Kubota L175 (ad in classifieds). I can't wait until it come in. BTW incasw an one wonders I ordered a 2520 with 200cx loader and 62d belly mower for $18800. I don't know if the price is right or not but that was all I could squeeze out of my local...

G,day from mick white , recently purchased a new jd 2520 and am looking for information & specs, performance on the jd 46 backhoe + 4 in 1 bucket info, plumbing,valves etc, any help- info would be appreciated...

I have a new 2520 on order and have asked my dealer a question and he really isn't exactly sure of the answer, but says he will get back to me. Maybe I can get a quicker answer here. The tractor is going to have the 62D MMM, without the independent lift. Meaning the deck height will be...

Hello all......I just registered on the forum, but have been following the posts in the CUT forums for a while. Seems there are a lot of very knowlegeable & helpful folks here, willing to share their views. I have a JD X495 with the 62C mower deck, front quick tatch and 54" Blade, and the...

Aloha, Anyone have/had a problem with their 3pt. hitch? After parking mine overnight, next day..3 pt hitch won't move changed the hydro oil and filter...still won't work. Front loader works fine.. ordered the manual for $200 but gonna take a week to reach me.. any suggestions/advice/ideas as...

Aloha, Anyone have/had a problem with their 3pt. hitch? After parking mine overnight, next day..3 pt hitch won't move changed the hydro oil and filter...still won't work. Front loader works fine.. ordered the manual for $200 but gonna take a week to reach me.. any suggestions/advice/ideas as...

I have a two year old 2520 with 70 hours on it and from time-to-time the power steering just quits, or is hard to steer. What are the possibilities of what's wrong?

Here they are pictures of my new tractor:D

Hey there - Need some advice & knowledge....I am looking for a 3 pt tiller and came across one (JD450) however it's a Catagory 0 3 pt. hitch & I was wondering whether this is compatible with my JD 2520 which has a Catagory 1 3 pt. hitch system? Any help on this appreciated greatly. thks.

The manual I have for my JD 2520 shows a fuse block with multiple fuses and empty spaces. On my 2001 JD 2520 there is only a small connector with 4 fuses numbered 1 (10 amp), 2 (10 amp), 3 (15 amp) and 4 (25 amp). I want 12 volts out the back to run the pump on my sprayer. My question is what do...

Hi all. My gas cap doesn't clear the hole in the hood very well. The cap is pressed tight up against the hole in the hood towards the front of tractor. Slight bend in hood from this. I don't remember this problem when I first purchased the tractor 3 years ago, but noticed it last summer...

Well I did a search for these two tractors and nothing was found so figured I would post my question/problem. Just for some background about me, I have no experience with any thing but a normal lawn mower. I think I got some of the abbreviations correct but I still don't know what MMM means...

JD 2520/2720 VS Kubota B2920 -------------------------------------------------------------------------------- I'm trying to decide between these tractors to buy. I have no previous experience with compact tractors at all. Just test drove the Kubota and am going to drive the JD. Just wanted to...

JD 2520/2720 VS Kubota B2920 -------------------------------------------------------------------------------- I'm trying to decide between these tractors to buy. I have no previous experience with compact tractors at all. Just test drove the Kubota and am going to drive the JD. Just wanted to...

Hi I have a 08 JD 2520 with a trans problem. The tractor has 207 hours on it. Last year when it had approx 100 hours the PTO quit working. The dealer said it was a broken pin in the tranny. It was fixed and worked great. Now a year and 100 hours later another PTO problem. This time the PTO would...

Just bought a CMI tandem trailer. Have had it welded in places where the production welds were limited. Now I am seeking a cylinder and control for the tractor. I don't know much about cylinder specifics and it seems the links from past discussion on the board don't work well. The 2520 has...

Recently purchased a new 2520. One issue that I have with it is that the removable pins to fold the ROPS down are so miss aligned that there is no way to put both sides back in. My local dealer has tried and couldn't get them in either. I had to drive the first one out with a punch and once out...

I have a John Deere 2520 with R4 tires, 200 cx loader the high capacity loader bucket and the regular, a drive on 62 d mowing deck that has never been used and only 137 hours, what is this tractor worth to sell it is a 2006 year model

As a new member to this forum this is my very first post....I want to say up front thank you all for the info here - it has been very helpful; and I also want to apologize in advance for what is a long first post, as well as for what may be "rookie" questions! I just sold my JD 790 w/#70FEL and...

Hi there - I am considering getting a rotary broom for my 2520 & have a couple of questions - Which model allows for hydraulic height adjustment - I know both will angle using hysraulics, but does which one can you adjsut the height of the broom using hydraulics and not just relying on the...

Hey all. Anyone added or know any information about a 3rd "Selective Control Valve" for the JD 2520 or 2720 compact tractor? I see in JD's parts website, that it is listed, but the dealer I ask about it was very "vague" on the specifics of it. In other words, he kinda lied to me, rather than...

Over the weekend, I made a boom pole for my JD2520. Since I previously made a three-point trailer hitch and quick hitch adapter for the loader, I decided to employ these elements in the boom pole. The other advantage to doing it this way is that the boom pole breaks down for easier...

Hi All, Check out my Bucket Hook mount with receiver that I came up with for my 200CX loader on a JD 2520. I'm hoping this makes the simple jobs easy now to pick up / move with the loader... I have added a 3/16" backer plate inside of the bucket, bolts are 1/2 diameter grade 8. Bill

Just a quick writeup. I was searching a while back for a PTO power washer and I saw that there were some brief discussions of people trying to make a belt driven or gear box power washer for there three point hitch. Here is a link to a youtube video I posted for those that are interested...

Newbie here - I purchased a JD2520 a year ago and now falling into the abyss of what other attachments and toys I can get for my little green monster. My question - I am considering a backhoe and have read alot about the Woods BH70-X - is this too much for my JD2520? or should I stick with the...

Last fall, I purchased an BB1184 for use with TNT on a JD110TLB. Haven't desired to remove the BH yet, until there is some concrete available out of the weather. So, I am excavating an area for a concrete pad and using the FEL. Bunch of rain and snow this week left the area soft and muddy in...

Does anyone have the wheel spacers for the 2320, 2520 or 2720? i see the price on jdparts is around 100$, just wondering is that for a pair or each? if you have them do they leave enough room for chains or do the chains rub? thanks

just thought i'd put a few finished pics up. I can't take much credit for the install, since jimgerken gave me most of the ideas and saved me a ton of money (on the power beyond hookups!!) i decided i wanted my valve in a hidden location, to make it look "Factory". i only hooked up one spool...

I just added a two spool hydraulic valve to my 2520. i tapped into the ports behind the scv block like i have seen on this website. i put the plug in the block. all is working, but the valve sometimes has a vibration/shuddering/squealing noise to it. if you run the levers back and forth you...

I found that quite often when snowblowing I wanted to increase engine speed to max for the deep snow parts, but otherwise wanted it running at 3/4 throttle for lower noise and wear. My right hand is already quite busy with hydraulic levers for lift and rotating the blower chute rotation. So I...

I managed to get V-bar ATV tire chains on the front tires of my 2520 and have used them for a few weeks now with great success. The secret was to make the inside side loop real big, so it rides up high on the sidewall and stays away from the steering mechanism. Then the outside side loop had...

I built this "cab" for the 2520 for snowblowing. It keeps the snow off, and shields me mostly from the wind. It is kindof open at the bottom where the material ran out of length, so my feet are exposed. On the other hand, if it sealed up tight it would fog up inside. The fabric is a golf...

I'm in the process of building a grapple for the JD 200 CX on my '07 2520. Does any one have some info on adding a 3rd hydraulic control for this? I've checked with 2 different JD dealers and neither have a solid answer. Any info would sure be appreciated. Thanks, Glen

hello, i have a 2008 2520 i am at 50 hrs and want to service it. i am changing all filters and oils i have a question on engine oil my dealer gave me 15w-40 and said thats what they use in all of them but my manual says 5w-30 which is correct or the best way to go? also what is the...