wheel

At 90 hours on my F2690, I had the first minor issue. I have the 72" rear discharge deck and I noticed one of the front deck gauge wheels wasn't running true. I knew I hadn't hit anything hard enough to damage it and the problem was 3 of the 4 nuts holding the two wheel halves together on the...

Just wanted to pass along my experience with removing a T4030 steering wheel. First, it was the most difficult steering wheel to remove I have encountered. The telescoping feature makes it difficult to get the proper pull on it to begin with. And the wimpy 6mm bolt holes that it is tapped with...

How can I get my 2006 Kubota 2100 to free wheel? I'd like to move it around the shop without starting the engine. Thanks!

Hi folks! I bought a Little Buck loader and now need to plumb it. I had no idea it was complicated! its only 2 cylinders? I have a pump A BDP-10L In fact I have 2 pumps. Sent to me by the little buck guy! I have been told it will take 2 pumps to power the loader? I also have a return tank...

I'd like to adjust my wheel width a little wider on my YT359 just for stability on my hilly property. I can figure out the wheel adjustment, but how do you folks mount/unmount a rear wheel filled with ballast? I've got a 2 post lift, just not sure how I'd get a 600+ lb tire back on the tractor.

As the title says..... My mower is a Ferris is5000z diesel (yeah, it's an older model). Last fall my crankshaft broke and long story short, I had the mower towed into the shop. They serviced it, but wouldn't touch the motor. I found a local guy to rebuild the motor, which is now working great...

We habe old lombardini 4wd if we attach the blough to the tractor the front wheeels start spinning in its place and not move and some time one spin and the other not move even we put small resistans in back it will happan can you advice

Looking at upgrading a old rake. I have used a Kuhn friends have but wondered about others, I see some Enrossi and Bush Hog cheaper that Kuhn. Their wheels are independent. Any thoughts?

Hello everyone, I've been using the forum here since just before buying my YM1700 a few years ago. I've been overhauling and replacing parts to get it in great working condition and love this little tractor for what I use it for. I'm now thinking about adding rear wheel weights for added...

Looking at Brotek… 1.4” or 2.0”. Nothing for the front wheels initially. Is there an optimum size choice here? I do not run a MMM.

articulated and rigid wheel loaders with telescopic arm or telehandler opinions performance comparison hello. i happened to see that some machinery manufacturers make wheel loaders with both articulated and rigid chassis with telescopic arm to be used with buckets forks or as small cranes. what...

The front wheel on our mt125 will NOT come off ... the lug nuts are removed and we have tries to hit it off with a 10lb sledge and the damn thing is not budging! We do have 2 in spacers on it also. The tire just doesn't hold air 24 hrs, so wanted to replace tire... now I think we may need to...

One but the brake doesn't work that's why the linkage broke any one delt with this?

Own a MT160D and the left rear wheel has rusted through and no longer holds air. All of the other wheels still have paint on them and are in good shape and this is the only thing wrong with the machine. I'm wondering if anyone has a spare wheel for sale or knows a junkyard of sorts that may be...

Probably best to just replace both as long as I'm having to drain the whole thing to replace one side, TC6Y628012 194312-32660 which I'm finding at around $35 each on most sites, but the site I bought the transmission fan at wants $32 shipping for these 2 seals? The site gives no alternate...

Try to figure out whats missing, there's a bit too much shaft/joint up/down more so with steering post plastic removed. There is a circlip 04612-00160 missing at the bottom of shaft although I don't see how that would eliminate all the play. I recall on my F3060 replacing the pipe steering...

I've been dealing with the problem of wheel ruts at my shed entrance for too long. This was yesterday: It's just the first 6 yards from the door going out, and this happens every year, as the sun always softens the frozen earth in this area. Yesterday was 9F - 19F, or something close to...

Has anyone replaced the non-tilt steering column with a tilt steering column on a current production JD 3E series tractor? If so, do you have a parts list and approximate cost? Alternatively, has anyone fabricated a bracket to allow the seat to slide rearward a couple more inches? The fuel tank...

Hello all, I have a Ford 3910 and it started to brake a bit the left wheel without braking. When I leave the tractor in an inclined road facing forward with both levers in Neutral and no braking, the tractor starts moving by it self due to gravity. But when I leave the tractor in an inclined...

I have a set of 4 1/2” Bora rear wheel spacers for a 15 series TYM or Branson tractor. They are extremely well made and include all the hardware. I ended up not needing these on the new tractor. These add a lot of stability to the tractor especially on slopes. I’m located in Alaska but willing...

Ive provided measurements to bro-tek and they're in the process of making rear wheel spacers for the tx25/h24. The front wheels are 5x4.5 lug pattern with a 3" hub opening and 87-06 jeep wrangler spacers work. The fronts require lug bolts, not nuts. The thread for the lug bolts is 12x1.25.

Just wanted to let you guys know that ive provided measurements to bro-tek for some rear wheel spacers and their working on them now. The regular h24 doesnt really need rear spacers but the plus model does with the taller/narrower tires. The front wheels are 5x4.5 lug pattern with 3" opening so...

I have a TC24D. The left front wheel will not freely rotate when cold. Just wondering if anyone else had this issue, of course there is snow and ice under the wheel and it just slides. I checked the fluid level in the axle and my past experience is that when the axle is warm the wheel runs free...

What are the odds? The left front tire where you drain the front axel fluid, I noticed a fluid leak. Brownish colored on the snow. Tractor hadn't moved in a few days. The day before there was nothing on the ground. Well ok, must be a seal under the housing. Next day there was a lot bigger spot...

My Kioti CK35 manual in front wheel drive is only powering the left wheel???

Need to access the fuel pump behind the cover for the steering wheel column. This means the steering wheel needs to come off. I have removed the nut and attempted using a gear puller but wheel won't budge and afraid of breaking the wheel. any tricks to get the steering wheel off?

Today I was out leveling a piece of my property when all or a sudden my left front wheel came off. At first, I thought it might have been the lug nuts that came loose, and the wheel came off the rim, but when I looked at the inside of the tire, I saw a splined shaft still attached to the rim. I...

So it's winter and it's time to deal with so many of the little projects and issues.. My little tractor had been doing something odd in the summer.. one wheel will just stop turning... if I stop and it starts again with no issues... Car guy in me says diff is jammed but if that's the case the...

Hi, I have a CG2310 that needs front tires. I managed to get the existing tire off the wheel and the wheel is very rusted. Completely gone in some parts of the rim and very thin around the bead. I've been trying to source a new rim, the tire size is 18x8.50-10. Does anyone have a good online...

Hello everyone, ym2210 I've have about 9" of play in my steering wheel for 5 years now. The play in only in the steering wheel, and shaft. it's not spinning loose on the shaft, so that would be the wheel and the shaft that have the play. I no the 1/2 moon key is broken off, because I can get...

I took the big nut off under the cap expecting to see a couple puller holes taped in the steering wheel?

Odd left hand front wheel intermittent lock up on my '21 GC1723EB, about 575 hrs, and could benefit from some advice. Only really happens in cold weather after sitting overnight. If I fire up and if I work if forward and back for a few minutes it eventually let's go and works normally. No noise...

I am going to build myself a timber forwarder with crane. It is going to be 6 wheel drive and I would like it hydraulically driven. I am thinking of using these for wheel motors : Silnik hydrauliczny BMR chłonność: 200cm3/obr obroty: 300obr/min z łożyskowaniem do rębaka I am after some advice...

I was putting my chains on my gc2310 prepping for winter, I jacked up the rear and found the right wheel was very hard to spin, the left spins freely. Thought it might be a stuck brake, removed the linkage and hammered the lever to the rear, had little to no improvement. Any idea what is wrong...

I found this recently and am curious if it is a tractor wheel weight or something used on a drilling rig? Any thoughts?

Waiting for an inner wheel bearing to arrive for my 15' flexwing mower. I already have the outer assembly. Memory from 40 years ago says: (after all is assembled correctly and greased up) 1. Tighten to an appropriate torque.... 2. BACK the nut off say, 1/2 turn then slide cotter pin through...

Latest episode: seems to be losing some power when on inclines (does great going downhill! 😜) and I have a lot more “whine” I think coming from the front one or both motors. And backing up on a steeper incline it almost won’t do now…am I looking at bad wheel motor issues?

tl;dr = Anyone know what the correct wheel lug nut torque specifications are for the R4047H front wheels? The Operator's Manual tells me to "Check torque of wheel bolts and nuts," under the "First 50 hour check." Ironically, I cannot find any mention of any torque specs in the Operator's...

Trying to grease the bearing on my bushog rear wheel. I attach the grease gun and pump and pump probably 20 times and I don’t see any grease coming out. Do I have a clogged zerk or do I just need to keep pumping? If the grease gun seems to be pumping does that necessarily mean that grease is...

I ordered my first tractor (TYM T574H) yesterday and am wondering if anyone dealing with hilly terrain has put spacers on to enhance stability. If so, what size? My dealer seems reluctant to recommend them, but I’d like to have them put on before they fill the tires if I decide to pull the...

I purchased a L295DT and have been doing some work on it and now into changing the rear tires. I’m doing the right rear first not only because it needs it the most, but also because there’s been a snapping sound, dull and rhythmic that can occur in that area when driving it. Before pulling the...

Ok excuse my ignorance, but I know most tractors with a FEL have some toe in with the front wheels to offset weight or heavy loads. However, looking at my front end, it looks like the left hand side(drivers side) is leaning way more than the right. Is this normal? How does one go about fixing...

Hello All! Looking for some help in finding replacement rear wheel rims for my 2000 LCG. Rear dual wheels are 8 x 28 and rusted thru with the tubes bulging thru the holes, so my wheels look like they have hernias. I have looked everywhere for new rims but can only find 9 x 28s. Any help here...

Do you have wheel weights installed on your tractor? Have you noticed a difference in performance?

Title pretty much says it all. Bought a camper 800 miles away, and made arrangements to pick it up on the way to my class reunion. Decided my old truck could use a paint job, and two of the neighbors do body work and paint, so after getting 3 estimates, I talked to those two. 1 couldn't do...

Does anyone here have information on front axle load rating for M59 TLB? My local TN dealer just shrugs and says they don't know. Messicks is going to call Kubota technical rep for an answer but nothing so far. Ive looked over operator and Workshop manual and found no info on front axle rating...

Hi TBN! Looking to replace the seals in the right front hub casing of my 1986 build 1210 w/ 4WD and I'm not sure how to tell which casing my 1210 has: SBA322011901 or 902? Parts dealer said the part is cast into the casing but the only number in the casing looks like 2Z 0A 33? (pic) Can...

As mentioned in the thread "Woods vs LandPride Finish Mower" I ordered a set of wheel assemblies for my Caroni RFM this past Saturday. The UPS truck dropped them off today. They came from High Grade Manufacturing. Very happy with them. Link below. At $52 each (The whole works - wheel, yoke...

This is my father in law's. I have been trying to keep up his place and it's gotten to the point that it's really difficult to use it like this. How would I go about finding parts for it. The biggest need is the whole tail wheel/yoke assembly.

Edit 7/28/24 - disregard. We got the machine home. If the thread stays consider it historical reference. Does anyone know how to find the dimensions and bolt pattern of the rear wheels on a 444 and similar machine (several series/models should share the same pattern)?

After some maintenance being performed (rear wheel/hub reseal and new couplers), I now can’t get the front wheels into the 4x4 mode. Looking at the MX service manual, the selector arm is fairly simple looking and doesn’t appear to complicated to access. The 4x4 mode did work after the above MX...

I've had a few 5th wheel/gooseneck trucks, all used... I am looking at purchasing another F350, but the one I've found doesn't have a ball in the bed. Just need it for farm purposes, towing. Dump trailer, tractor, equipment on flatbed, etc. 2006 F350 Crew/diesel What is a reasonable cost to...

Wanting to know ,what oil to use in my transmission in my 2420 farm pro 2 wheel drive..

Noticed, front wheels spinning even when manual lever in 2WD. The lever feels like it engages/disengages.

My 4500 diesel wheel had come loose and the holes are badly oblonged. Is there an aftermarket 8 inch wheel that would fit?

Hello, Had to get the tire / innertube replaced in town and now I'm trying to re install wheel onto hub but cant find the tighten specs for it. Thinking no more than 80 foot pounds. Your thoughts, Dave

Hello, I have a 1987 Ford 1520 that's developed a leak at the right wheel on the inside. I have not pulled the wheel off to check on it I am hoping it could be a seal. Does anyone know if there is a wheel seal in there? I have a front-end loader that I installed and it has not been abused but...

Any know how to adjust the clutch? Wish I could find a service manual. Nothing available online.

Any know how to adjust the clutch? Wish I could find a service manual. Nothing available online.

Sorry if this is a stupid question but I noticed that my Yanmar rear wheels seem different than some of the ones pictured online. Were there different wheel options to order the tractor with? Mine looked to be fixed while others seem to be adjustable. My wheels pictured below: Pictures of...

I'm interested in getting a set of 2" rear wheel spacers for my 3320. I know there's a lot of good brands out there. Bora, Bro-tek and others. In my research, I saw a thread where the person got his spacers with the centers still intact. Like Deere offers. But, I don't remember where I saw the...

First, apologies to Vintage Wheel Horse purests. Take a deep breath before continuing ;). My grandson's 'other' grandparents had an old 1961 Wheel Horse in their barn. They used it for mowing and snow plowing 'way back' when their son (my Son-in-law) was very young. My Grandson, Ethan wanted to...

First time poster. I have an F15D Forte with a RSA1201 auto tiller on it. Currently, I'm in the process of changing my rear axle seal. While in the process I thought I'd address my gauge wheel that isn't turning. I started the disassembly process but I'm currently stuck at this point as the...

Does anyone have experience using generic versions of the white ce400 wheel motors used on the smaller PTs? Anyone ever mix name brand wheel motors with generic versions on the same machine and if so, did it cause any problems? I ask because I have had zero luck with rebuilds over the years...

Proble we have is too many of them nasty black locust thorned trees on our property and i get a flat everytime i mow etc...Is it good to foamfill the front tires? $500 for front tires only.Any downside to foam fill?If they last 5 years it will save me money and labor. 7 16G.1W is on front...

I thought someone may have spent the $$ for a set of the latest greatest fad TWEELS 🤠 Mike text or call six78 98six 322six

Plowing heavy snow yesterday I heard a bang and the right rear tire seized. It will move a little. I'm hoping it's a brake problem... Any advice before I dig into it appreciated.

Hi, new to the forum, apologies if this question has been dealt with before. I inherited a Cub Cadet 7200 that's in very good shape overall and I intend to use it very lightly. I noticed that the front right wheel is leaking fluid so I'm assuming that it is probably a seal. I can't find the part...

My RK55HSC has developed a pretty annoying steering wheel squeak. Everything in the cab seems covered with plastic and inaccessible. I've greased what zerks there are below the tractor. The noise seems to be inside near the steering wheel. Does anyone know how to get to whatever linkage and what...

Hello all, Have a 755 JD sitting in barn of recently purchased home/property. Planning to move it into shop to begin working on it soon. Tinkering with it the other day found that the steering wheel spins freely. Haven't started it yet, still need to get a battery for it...plan to do that this...

I have a 7195 Cub Cadet with a bad front swivel seal. I checked all the online parts dealers with no luck. They all tell me it’s obsolete. Does anyone know of another place or what can I do besides keeping it full of oil. Need help. Thanks

Hello, have a Mahindra 5010. Noticed hydraulic oil around the edge of the rim, one wheel much worse than the other. How does that happen? Would it be common for there to be an axle seal and it's gone bad and is leaking? I think this is a 2014 model, would it be unusual to have a seal go out in...

Two questions: I have a commercial-grade JD Zero Turn mower that I use to mow my rural property. It was purchased in 2012 and has 870hrs on the clock. It is serviced regularly and is in excellent shape. The dealer says that it is time to replace it because JD is discounting the 2023 models, and...

can the rim and wheel plate be in any orientation to get the width you want? I have a 4720H and the 3 point stabilizer bars are too close to the tires since i installed the pat's system to run my tire chains. it appears that I can put the hoop on the rim on the outside instead of the inside of...

Hello, very new to dealing with wheel bearings. I just have a couple of questions about the old hay wagon hub pictured below. Does the grease seal separate from hub where I’ve drawn that red line? Also, the little inset in the casting you can see when looking inside the hub (there is another...

If you order spacers for the rear wheels of an RK37HC double check your bolt thread pattern. I just got 6" Bora spacers and they came with 16x1.5 bolts with sloped heads. (Those have to go inside the spacers and attach to the wheel hub.) My RK37HC has 16x2.0 bolts with flat heads so those...

Can anyone help identify this wheel? It's 40" diameter and 3" wide. IHC stamp and numbered 8707. Thanks for any information!