Price Check Kioti rx 6010 or Kubota mx5100

[Christian500]

I am not one to even bring up resale. 20 years ago, when JD and kubota were the large CUT and SCUT players, maybe. But anymore, kioti, mahindra, LS, etc are all top notch brands. And with the internet, and research being right at ones fingertips, quickly weeds out bad brands/models.



Perhaps.

But I think there is alot of misconception in this thread.

First, I have no idea what a NX5510hst open station cost in comparison to a MX. Unless kioti has something on their website I am overlooking.

Second, you are assuming that the 40k for the new mx5100 that the op told you was accurate. Well, fact-checking.....I think that is either total BS, or we are missing something. Like was that price quoted with a bunch of attachments or a backhoe? The MX5100 for starters, is not a new model. But the replacement, the MX5200, HST, equipped with a loader and HD roundback bucket, only lists a MSRP of $34k and change on build-my-kubota. So its probably a $30k tractor.

What can one buy a NX5510 HST open station with loader for? Tractorhouse would seem to indicate they are $36-37k with a cab? Take the cab off you think they are still gonna be 5-10k less than an MX? That would have to put them in the $20-$25k range, and Im just not seeing it.

As to comparisons....yea, the MX is not a luxury model. One of the reasons in fact that I like it. I like the features like telescoping links and stabilizers, but not fond of lots of electronics. But to each their own. The NX is about 400-500# more tractor and does have a stronger 3PH. But the MX 3PH can lift 2400#. 99.9% of NX owners would probably never exceed that. As to the loader, I'd call it a wash. The NX certainly dont have a "stronger" loader.

The Price is for a mx5100 with 4 and 1 bucket and slasher without slasher its 39000... this is australian prices not bs

 

[LD1]

The Price is for a mx5100 with 4 and 1 bucket and slasher without slasher its 39000... this is australian prices not bs

Australian prices make sense now.

So 39k for a MX

Whats a comparably equipped NX go for new? And what does one go for that is equipped similar to the used one you are looking at?

Without knowing new prices, its hard to say if the used price of $30k is good or not.

 

[TSO]

Australian prices make sense now.

So 39k for a MX

Whats a comparably equipped NX go for new? And what does one go for that is equipped similar to the used one you are looking at?

Without knowing new prices, its hard to say if the used price of $30k is good or not.

But regardless, $10k less for a bigger, stronger tractor with a cab, is a good option ( again assuming the used tractor is in good condition)

 

[sixdogs]

I have an MX5100 and have owned lots of tractors over the years. The dealers have stood by me when they shouldn't, the tractor never quit and I couldn't be happier. Parts are moments away probably no matter where you are. My vote is Kubota.

 

[LD1]

But regardless, $10k less for a bigger, stronger tractor with a cab, is a good option ( again assuming the used tractor is in good condition)

Not necessarily. Maybe the nx is a bad deal, and the MX is just a terrible deal.

What if a new NX equipped the same, is only 33k?

I could have a 9n in average condition for sale for $6k and you could find an average 8n for $4500 which is a better machine. Doesn't make it a good deal

 

[GManBart]

The Price is for a mx5100 with 4 and 1 bucket and slasher without slasher its 39000... this is australian prices not bs

At the current exchange rate, that's right around $30K U.S.

 

[LD1]

At the current exchange rate, that's right around $30K U.S.

Never bothered to look up exchange rates, but that puts the 500 hour NX at ~23k USD

I bought my MX for 20k......which would be roughly 26k down under.

Wasnt much at all used around me when I was looking though. Its either old 2wd stuff, or new. Not real common to find newer machines with fewer than 800 hrs and ~50HP around here. Let alone finding one that was HST, SSQA, and at the dealer 10 minutes from home

 

[GManBart]

Never bothered to look up exchange rates, but that puts the 500 hour NX at ~23k USD

I bought my MX for 20k......which would be roughly 26k down under.

Except the 500 hour machine is an RX, not an NX, so it's much bigger.