MF 165 knocking
- Thread starter DaButcher
- Start date
- Views: 62891
-
- Tags
- massey ferguson 165
The kid
Elite Member
- Joined
- Apr 25, 2012
- Messages
- 3,888
- Location
- Middle Tennessee
- Tractor
- 1965 135 gasser, 1967 135 diesel
You can probably use the report button (bottom left triangle) and state where to move it in the message thread.
OP
DaButcher
Silver Member
This project is back on my to do list. Bought a standard crank and have it sent off for polishing or turning if needed. Also have a master overhaul kit, oil pump and other goodies coming from the local MF dealer. If anyone is interested I will post progress pics.
Bird
Rest in Peace
It's done.
DJ54
Elite Member
- Joined
- Jan 20, 2009
- Messages
- 4,538
- Location
- Carroll, Ohio
- Tractor
- IH Farmall 656 gas/ IH 240 Utility/ 2, Super C Farmalls/ 2, Farmall A's/ Farmall BN/McCormick-Deering OS-6/McCormick-Deering O-4/ '36 Farmall F-12/ 480 Case hoe. '65 Ford 2000 3 cyl., 4 spd. w/3 spd Aux. Trans
OP
DaButcher
Silver Member
Tear down continues
The filter caught some of the spun rod bearing pieces
This is a good reference pic for where the different length studs go
Removing head studs
While maybe not the ideal method it works (thanks for the tip shona13). I did find minor damage from sometime in the last forty years of someone else doing this same job
Somebody made a mess
Degreasing time
Got some goodies
Primed and block painted, finally time to turn the corner and start assembly
The Crankshaft I bought should be ready soon from the machine shop, for now I'll continue to clean and prep parts
The filter caught some of the spun rod bearing pieces
This is a good reference pic for where the different length studs go
Removing head studs
While maybe not the ideal method it works (thanks for the tip shona13). I did find minor damage from sometime in the last forty years of someone else doing this same job
Somebody made a mess
Degreasing time
Got some goodies
Primed and block painted, finally time to turn the corner and start assembly
The Crankshaft I bought should be ready soon from the machine shop, for now I'll continue to clean and prep parts
murphy1244
Super Star Member
- Joined
- Nov 25, 2011
- Messages
- 16,320
- Location
- Ohio
- Tractor
- Kubota 1120 RTV Kioti DK-40, MF-135, Ventrac 4500Y
I just love simple green.
shona13
Gold Member
- Joined
- May 5, 2012
- Messages
- 367
- Tractor
- Massey Ferguson 148 .Chamberlain Super 70. Caterpillar D4. Chamberlain 354 FEL.Toro 268 rideon kubota L2002fel
G'day Da Butcher.
Good to hear from you again.
I,d say your approach to the job is spot on,everything nice and clean,excellent pictures and I am sure the members would like to see MORE, Please.
Keep up the good work.
Regards.
Hutch.
Good to hear from you again.
I,d say your approach to the job is spot on,everything nice and clean,excellent pictures and I am sure the members would like to see MORE, Please.
Keep up the good work.
Regards.
Hutch.
OP
DaButcher
Silver Member
Ran into my first problem. The sleeves that came out have a thick flange that goes into the counter bore of the block and the new ones are thin flange. Called the parts guy and his conclusion is I have a early block with a later direct injection head. He is going to order the indirect rebuild kid and swap it out for me. I thought from early on something wasn't adding up about the engine because this appears to be a 1972 model tractor and by then the engine should not have the rope rear main seal yet it does. Question: Does this combination of head a block work good or create monsters? Previous owner ran it for a few years like this, but did have #1 piston and sleeve replaced.
I'll get a better pic later
I'll get a better pic later
OP
DaButcher
Silver Member
Ditto........I did use several products including Gunk degreaser followed by the Simple Green the lots of pressure washing