I have a Kubota L3710 with HST. It began refusing to crank this year. I noticed that the tractor would start when I jiggled the F/R pedal, so I thought there had to be a sensor somewhere that...

I had a dealer pick up my 1999 L3710 HST for its 800 hr service yesterday. In addition to fluids/filters I'm having 9 original hydraulic loader hoses replaced. They're going to quote replacing the...

Good day to you all. I recently purchased a Kubota L3710 HST. And am thinking of buying a used, in good shape, Woods BH9000 backhoe. The backhoe is advertised as coming off a Kubota L4310. It has...

About a week ago my 25 year old Kubota L3710 started having an electrical problem, the glow plug light on the dash would come on, (I'm guessing the glow plugs were also on). After a few seconds...

2000 or 2001 L3710. I'm not exactly sure what to call these parts to be able to do a proper search: control valve lever? the lever that maneuvers the bucket. as you can see, that heim...

have a L3710 4wd that front seals leak. have the hub off and looks like i may need a big clam shell puller to pull the ring gear. can i cut the bearing against the ring gear for easier removal ...

I have a guy who is trying to fix my L3710, which has a hole in the front gear case. He says this is a common problem because Kubota put the steering cylinder in the wrong place. They break and go...

Any thoughts on a Kubota L3710? I'm thinking about going to look at one, it is a 2003 and has 4100 hours. Anything I should look for? Any problems? What do y'all think of that number of hours?

Hello all. Has anyone seen this happen before? Looks like there was a stress fracture starting and when I tried to back over an ~8" log it was more than it could take. I'm contemplating...

While I have my Kubota L3710 apart to fix the steering cylinder, I want to change the motor oil, hydraulic fluid, and filters. Are there better oil and hydraulic fuel filters than OEM? Figured I...

With help from forum members, I dug into my Kubota L3710 to see why fluid was pouring out. I saw that it shot out from the rear of the steering cylinder when I turned the wheel, so it looks like...

I have an L3710 with an LA681 loader. I need to change the steering hoses. That means I need to get the side covers off. That means I need to take the front loader off. I looked at videos of...

My Kubota L3170 has started leaking fluid under the front end. It appears to be coming from above the two steering lines that are exposed on the bottom of the tractor. Moving the FEL doesn't seem...

I am using my Kubota L3710 more these days, and I am not happy with the tines mounted on the bucket. They are strong enough, but they are a pain to remove and attach, and they are hard on the...

Hello, I'm hoping to get some insight to a fuel related problem that I have been fighting for about a week now. I was going to bush-hog my property and my tractor started right up after a long...

In need of a grapple on the front of the tractor. Equipped with a skid steer quick attach. I'm thinking something along the lines of 60"-66". Smaller size. What's the weight limit I should be...

I have a L3710 HST tractor and I have had it for over 20 years and never had any trouble starting it except when the batteries went dead. The other day 3 weeks ago I used it for one or two hours...

I broke my right side tie rod today. I'm planning to replace both parts. Any advice / hints on how to do this? I've never done it before. Thanks in advance.

Going to go ahead and change the hydraulic fluid in my L3710. Tractors and hydraulics aren't quite my forte. There a go-to place for filters and stuff? Like a SummitRacing, only for tractors? I...

Background. I bought my Kubota new around 2000-01. I have had no problems in 20+ years and 1400+/- hours of homeowner use. The tractor does live outdoors year round. I'm 71 and retired. So, my...

Does anyone have the owner's manual or instructions for putting this back onto my tractor. I took it off o.k. but I can't seem to get the dang thing back on. Assistance would be highly...

Does anyone know the part names or numbers for the front metal cover and light assembly for an L3710, and/or know a good used parts dealer? I had a little incident with a log in the woods today...

I just replaced the front tires on my L3710. I was thinking this would be a good time to repair or replace the tie rods. Both have small bends in them as you can see in the pictures. Dealer is...

Looking to add a thumb to my L3710. Prefer hydraulic, but a manual one is fine. I've got a Hobart 180 220v welder on mixed gas, so I'm fine with welding. The Woods9000 backhoe runs off its own...

Looking at a tractor loader combo but i need to beable to move the thing. Do my numbers look correct here? L3710 Tractor 3500lbs La681 Loader 800lbs? Its the quick detach version Two 14.9x24 rear...

The tachometer was working perfectly. Then I hit some rough terrain and the cable came off. Ther Kubota serviceman put the cable back on, but the RPMs are bouncing all over the place now and are...

Not sure if this belongs in the general Hydraulics area or what, but here I go. My L3710 leaks hydraulic fluid like crazy. When I bought it used, the mechanic who inspected it said it needed new...

That time of year again. Our driveway is a quarter mile long with a somewhat steep hill at the end. I've got an 8' plow on the front and a Woods9000 backhoe on the rear of my L3710. As of...

I live on a farm in northern Florida. I don't grow anything except squirrels and spiders. I have around 16 acres of leathery bahia grass and about 18 acres of live oak woods. I have a 72" King...

Loader valve on my L3710 is not working properly. The spool on the curl function does not return to center so it inadvertently curls when you least expect it unless you hold the lever in the...

Anybody have a schematic for a L3710 that they would be willing to share?

Any tricks to getting the cir-clip out of the cylinder end caps? Need to replace the seals and the o ring in the end caps.

New member here. So I recently purchased a 2002 Kubota L3710 with a front mounted snow blower which uses the mid-PTO. What is the correct method/process for engaging the mid-PTO? How do I...

Who makes largest compact tractor ?

I have an interesting choice to make between two excellent tractors. Tractor #1 - 2002 Kubota L3710 4x4 with LA681 loader with 66" bucket. Ag tires. 780 hours 2-owners plus me. I've owned for 3...

I'm in the middle of replacing the upper, front oil seal, part "A" or 060 from this old thread http://www.tractorbynet.com/forums/kubota-owning-operating/123302-need-help-w-kubota-l3710.html...

I lost my neighbor who used to plow our lane, so I'll have to take care of myself now. I have a Chevy Silverado 1500 4wd, 4.8L V8 standard cab 8' bed truck an a Kubota L3710 with standard FEL (no...

I am trying to replace the lower arms on my L3710 and it looks like the pin holding the arms in terminates in the brake case. The pins are very rusted and won't budge. Please help?

I purchased a Kubota replacement seat from Amazon $99....looks great...said to fit L tractors. My issue is that after removal of the old seat frame /foam....there is a complicated seat mechanism...

I work for a municipal fleet and we just got a couple of older Kubota tractors from another location to service. Being as I have had Kubotas for years I am the candidate to take a look at these...

Folks, It's my first post, but I have had several Kubota's and need a couple of confirmations before I go forward on adding a rear remote for my L3710. First off, I have a 3Pt stump grinder...

Hydraulics were erratic on the loader. Operating the control valve to raise and lower the bucked caused the bucket to lift slowly or not at all. Hydraulic fluid is at proper level. I loosend one...

I have a Kubota L3710 tractor that will not start and I am looking for some assistance. I had used it several times this day with no issues but now it will not start. When I turn the ignition key...

Best method for warming engine and hydraulic oil in cold weather?

Hey there, question my tractor won't turn off with key anymore. It was running fine, new battery and a couple days later the battery was dead. I jumped it and it ran for a couple hours, then it...

Please, someone tell me how best to reach and remove the overrun clutch inside my Kabota L3710 HST. The PTO has no power, and I do not hear the clicking of the over run clutch when the brush hog...

Have a set of rear hyd remotes. Confused, can I run the log splitter simply by connecting the two lines to the remotes? Thank you.

Hi all, I have a leak it appears at the bottom of the case of my right front bevel gear case. Also when I had previously changed the gear oil I noticed some metal shavings in the oil. I found...

I need some help, I'm trying to fix a neighbors l3710 that won't start the battery checks out but it won't crank. The lights are fine one minute and dim or out the next. We have cleaned the...

I seem to be having an issue with my L3710 HST. Over the past year or two the hydraulic power seems to be decreasing. I'm having to keep the rpms higher than I used to, it doesn't climb hills like...

Has about 900 hours on it and for some reason reverse works normal but when you push the pedal for forward travel the tractor will not move till the pedal is almost fully depressed and movement is...

I picked up my first tractor this summer and am really happy with the L3710 but the side exhaust is bad when tilling all day. Do they make a rear exhaust retrofit or is ther a modification forum...

I can't get my 4 wheel drive to engage on my L3710. The lever used to be difficult to put in and out of gear. Now there isn't any pressure moving it either way. It doesn't just flop around it...

Approximately 1996 model runs all day long at low <2000 rpm but when I idle up to engage the PTO it immediately overheats. Thermostat / radiator / other. I am new at this and any help is welcomed.

My neighbors L3710 has what appears to be a broken steering linkage? The boot is ripped and the wheel is tilting out. I'll try to get a picture, anybody had this or anything like it happen?

I know there are a few threads on this, but I can't seem to find any solutions. My FEL on the L3710 has been slower and weaker lately. Not much, but seems to be getting worse. It's a Bushhog 2045...

Can anyone help me with replacing my starter on a Kubota l3710? Are there good sites to look at? Do online manuals exist? Thanks. PJ

I am at a toss up of getting chains for my rear tires or adding some pallet forks to my bucket up front. I could really use some pallet forks. My bucket is not quick attach. I noticed on my bucket...

Should both front wheels be driving when I have the four wheel drive engaged on my L3710? While plowing snow I spin often with the industrial tires when things get slippery. Tread is in good...

I have the pump off and a new seal but do not see how to remove the old oil seal around the shaft that goes into the engine. I have removed the clip ring but the seal seems seated do not want to...

I managed to break the lower arm and cannot figure out how to remove the arm from the tractor. I see one small bolt with some kind of plate but, when I remove the bolt the plate didn't move. What...

have taken tractor twice to dealer with same problem. pto won't disengage. they said they haven't ever encountered this problem before. it has 100 hrs. on it since the first time it was "fixed"...

have taken tractor twice to dealer with same problem. pto won't disengage. they said they haven't ever encountered this problem before. it has 100 hrs. on it since the first time it was "fixed"...

The hand crank on my L3710 used to rotate the 3 point hitch will only move a couple of turns. Has plenty of grease. Any suggestions on how to fix it? Thanks.

Does anyone have any idea why the engine doesn't stop when I turn the key off on my L3710? I can also remove the key while it's running. The electronics all shut down and gauges go to zero but the...

Can I put other (newer/different) loaders on my L3710, other than the la681/682? specifically, I was looking at the 723. I can't seem to find the 681's around for sale, and need a FEL at the...

I'm located in SC and have a L3710, about an 04 model with 1300 hrs. This tractor is in pretty good shape. There is some light paint fade due to previous owner not garaging it and one L3710 decal...

I just bought a L3710 HST, 3400 hrs, I have all of the maintenance records, its been worked hard, but should now have an easier life. There is a hydraulic leak coming from the oil seal on top of...

am new here. just borrowed my sons kubota l3710 and sure need an owners manual. can't find one on the web so far. our old leyland is dead and gone to tractor heaven I guess. this kubota is sure...

Hi All, My 1999 L3710 has been sitting for about 3 months since we haven't had any snow. I went to start it to get it out of the way so I can get my riding mower out and it wouldn't crank at all...

Coming up at auction is a Kubota L3710 selling as a package with: HST 4690A 12" backhoe (3 pt hitch type) LA682 Loader (has chain hooks welded to the top, no teeth in the bucket) RC7236A Belly...

Newbie, I recently purchased a Kubota l3710 4wd FEL I found this site last night and hope to see a few comments Good or Bad about this older model tractor. I am looking for a owners manual and or...

My current tractor is an L3710 with 1290 hrs. Very good shape except for the seat is torn and has some fade. Also, it is the GST model. Recently, I found the exact same tractor at a dealer except...

I'm looking at purchasing a used Laurin cab off a 1998 L3300 to go on my L3710 HST. I contacted Laurin Cabs directly, and they would not tell me if it would physically fit my tractor, saying...

I have a Kubota L3710 with a BushHog 2045 mid-mount front end loader. I'm planning on building a tree shear but first need to add a 3rd control for an auxiliary hydraulic hookup on the FEL. Sorry...

I haven't noticed the whine before. The tractor has been parked for over a year. Yesterday I put a battery in and it started fine. I didn't run it much yesterday. Today I bushhogged for about an...

Kubota L3710 will not shut down by turning key off.Manual shut down by fuel shut off lever only.Has anyone got a link to a diagram of this electrical system or trouble shooting steps. Thanks for...

What is a L3010 4x4 standard trans with shuttle shift,ags,loader,with 680 hours worth in good condition? thanks

I recently had my metal return line replaced and complete servicing at 1000 hours. Now the bucket stalls when I go to full throw on the up lever. Partial throw on the up works fine as all other...

Our 2001 Kubota L3710 hst with 8300 hrs on it has a few problems (Problem 1) it recently has had the pto stop working. We assume you split the case between the rearend to get at the clutch. Is...

i have a kubotat l3710 and its making me think a clutch safty switch is out or the starter safty switch is out so what i need to know is where they are and which one has gone out on yall the most...

I have a Kubota L3710 with a front end loader and bought a Kioti backhoe, it has a frame mount with it, any Ideas how to make it work on my tractor? I made a front mount on the loader bracket and...

I've just inherited about 40 acres of field mowing to do. I have a kubota l3710 and a 5' bush hog but mowing that much acreage I'd be forever and a day. I'd like to get a larger mower, but I am...

I have been reading this forum extensively for the past few years. I taught that it would be time that I post a project that might help others. Sot here goes. Last year bought a Wallenstein...

Looking at a 750 - want to know your thoughts on sizing - is this too much hoe for an L3710? Woods says they can't say yay or nay because it is a 3pt setup and depends on the beefiness of the...

Hi everyone! Love the site. First time tractor buyer. I have opportunity to buy 2004 Kubota L3710 with 900hrs. Hydro trans. Turf tires. Kubota Front loader. No quick attach. Tractor has...

I have just taken up the responsibility of maintaining my in-laws tractor (a L3710) w/very limited knowledge of tractors and no manual to be found, its been a slow start! I found many answers so...

I have a 2001 L3710 cab HST with loader. I do a lot of everything with it. A great tractor. However I have developed what I can best describe as a severe squeak that seems to eminate from just...

Where may I find the serial # for the L3710 I need to find out the year Thanks A-lot

I need some advice as to trade in price on a Kubota L3710, 800 hours, dual PTO, heavy duty bucket, plenty of ag tire left. I might move up into the 40+ PTO hp range and the financing looks pretty...

Started and ran today many times ....shut it off, now no restart. Dash lights, headlights, start solenoid near inj pumps operates, but dead starter...not even a click. Removed and charged...

Started and ran today amny time....shut it off, now no restart. Dash lights, headlights, start solenoid near inj pumps operates, but dead starter...not even a click. Removed and charged battery...

I have an L3710 and I'm looking to get a snowblower. Of course I have to get one as wide as my tires and in measuring noticed that the rear tires seem quite wide, maybe set up that way for...

I'm looking at an L3710 with Gannon, tilt n top...2 things about the tractor that I need an opinion or 2 on... 1st R4 tires..all I have ever used are ag...are these worthy in loose dirt, how...

Hello! I need to know it's a good idea to change my oil by 0w40 synthetic?? My tractor have 1800hrs on the clock and he always have 15w40 standard oil in.A friend of mine say it's not a good idea...

I found a L3710 ( power glide trans.),with LA-463-1 loader, with 399 hrs and industrial tires, good condition. Private owner asking 15,750, I was going to offer 14,500, does anyone think this is a...

Hi Guys, It looks like the knuckle joint on my front end is leaking oil. I just topped it off and it took 2 quarts. How much work is it to get this rebuilt? What kind of seal does this have...

I'm a new owner of a L3710GST and noticed that there was a hydraulic in the clutch housing drain plug. It is one drop a minute so it leaves a nice puddle on my garage floor. I am thinking this...

Help! I am doing the 800 hr service and ready to adjust the valves. The kubota manual does not show the location of the timing window and it doesn't seem to be back in the area of the flywheel...

I hasve a 2000 L3710HSTC w/ approx 500 hours. it has developed a small drip/leak on both sides of the front axle on the bottom of the bevel gear housing. Has anyone had experience with this and...

I hasve a 2000 L3710HSTC w/ approx 500 hours. it has developed a small drip/leak on both sides of the front axle on the bottom of the bevel gear housing. Has anyone had experience with this and...

Anyone know where I can get a replacement battery terminal for an L3710? I don't want to have to replace the positive wire (rewire) and hoped to just replace the broken battery terminal. The...

I'm thinking about buying a JD 7000 with the no-till coulters which weighs around 1500 lbs. My Kubota is the L3710 with 4x4 and suitcase weights on the front. Myself and another guy "think" the...

I posted on here a couple of months ago, since then we (my dad and me) have decided to go with the Kubota 6040 or 7040. My question is my dad has a L3710 4x4 fel, hst, and turf tires. It...

After fixing MMM gearbox leaks, & putting back on L3710 tractor, I mowed about 10 feet of grass & PTO just stops. Didn't notice any thuds/sounds nor oil puddles. Deck belt spindles move freely...

I used my L3710 on a job last summer scrapping seven aluminum railcar hoppers. I need to be able to substantiate a rental charge. The tractor is a hydrostatic w/ loader, two remotes, and solid...

I recently bought a house and with the house came a L3710 (750 hours) and G1800 (350 hours) to mow the 7 acres of grass. The glow plug light on the dash of the L3710 was not coming on at all...

Hey, guys. First, I really need to thank everyone here in the TBN forums. For a few years (first as a Guest, then as a member) I've been reading these forums and I have REALLY benefitted from...

Hello. I need to change the oil in my L3710. I haven't had it too long and have never changed it since I got it used. Does anybody know the correct filter and oil type/amount to purchase? Also...

I have a Kubota L3710 2002 Model. It has 272 hrs on it. I am hve a couple of problems I would like to see of anyone else may have seen. The first is now when I turn the key off it does not turn...

owning-ML-875495-ML- Posted in wrong forum.

I will be selling my L3710 HST, LA FEL, HYD top & tilt, turf tires, 640 hours. The tractor has been well taken care of and stored under a shed. What should i expect to receive? Thank for the...

Last weekend while box scraping I heard a pop, turned around and my box scraper disconnected.... After 500 uneventful hours I managed to break a lower lift arm while turning a corner with a fully...

Does anyone know if I can change my lower arms on the 3pt to the extending type?

Found this used tractor for sale with 450 hours on it. It's got R1 tires, loader, and box blade. It's very clean. Wants $11,500. Too much or just right? Central Texas -Osconda

Hi all, I am going to look at a 2000 L3710 with FEL and backhoe tonight. It is hydrostatic and has about 700 hours on it. They are listing it at 19,900. What are your opinions on this price...

Anyone in the market for a 3710? I just saw one in our local paper...the ad reads: Kubota 4wd 3710, 40hp, shuttle shift, w/ FEL, box scraper, bushhog and backhoe. Less than 300 hours. All for...

Hey guys I'm new here and need some advice from your experience. I'm looking at two tractors for family and business use a '03 L4310GST with 125hrs and a '01 L3710GST with 760 hrs. The 3710 has a...

At the risk of opening my mouth and removing all doubt, can some one help? I have been using my 3710 with loader in Low Speed and the hand throttle adjusted to 1800 to 2000 RPM. I've just...

The boss has given me tentative permission to buy a loader for the 3710. Could you guys give me some good brand names and features to look for. Also some idea on cost. Thanks!

When I fully raise my rear blade on my tractor, it sounds like the engine is straining. If I then lower the blade a very small amount, the engine returns to normal. Any thoughts/suggestions...

I own a 2 year old Kubota L3710HST tractor. During my annual tractor clean up last winter (2004) with approx. 75 hours on the motor, I noticed a residue path below the water pump weep hole. It...

The family has recently expanded to include "a might as well be new" L3710 GST with 682 loader and loader rear tires. When my father found an L3710 GST that is just about 2 years old with 48 hours...

I got a line on a 2002 L3710 with 134hrs. Shed kept, owner operator and is in new condition. No FEL, but has box scraper w/hydraulic ripper setup, MM PTO but no MM attachments. What's it worth...

Anyone out there have or know where I can get a used service manual for a 2000 L3710 or a LA681 FEL? I just can't make myself give up the $150++ for them from a dealer. Any help is appreciated.

Someone that I work with mentioned he knows of a 2002 L3710 with 100hrs, no FEL but a heavy-duty mower and full hydraulic 3pt with box scraper and hydraulic rippers. The guy wants $18,500. Doesn’t...

All, Does anyone have an Allied 295 Loader mated to a L3710? I have an opportunity to purchase a used 295 and was wondering if it is comparable to Kubota's LA682 Loader? Any thot's? Thanks.

I have an appointment to look at a used L3710 Tuesday and cant find much information on this site about them. It has 140 hrs and HST trans and FEL. What is a L3710, how much horse power does it...

Dealers, Looking for a Used or New Loader for a L3710. LA682 or generic. Plumbed, required just the mounts, loader arms and bucket. Plesae send me a PM. Thanks.

All, Looking for a LA682 (or comparable) Loader for 2002-L3710. Can some one tell me, who runs the best source for Kubota Parts via the Internet? Require a few plastic body parts which are...

G'day, all! First, I want to say "hey" to everyone...it took me a while to register on the forums. I appreciate all the dicussions/information in here as they helped me in my purchase decision...

I am new to this forum abd to tractors in general. what is a fair price for a kubota l3710. 3 years old with 153 hours. i do not know what model it is. image is attached, dan burt [ </font><font...

Looking at 1y.o. Kubota L3710, HST, 150 hours, with loader(not sure the number), power steer, cruise, 4wd. Looks perfect, no scratchs, PTO not used. Man wants $16,500 in central AL. Good price...

I am getting closer to making an offer on a tractor I have not seen. The sales guy at the dealership is 100% trustworthy so I have no qualms about buying this thing sight unseen. The tractor is a...

One of my local dealers has one on the lot with around 450 hrs. I have not seen it yet but he says it is in good condition. For those of you who own one, what do you like and dislike about them...

Hello list, I'm starting to look around for new tires for my Kubota L3710. I had a few questions that I would like to throw out here on the list and get some feed back on. I currently have...

Greetings, I am in the process of purchasing a used L3710 HST with a woods 7500 Backhoe. Its a 2000 with ~500 hours on it. The price is 21,000. It looks fine seems to drive OK, but I wouldn't know...

I didn't realize until now that the L3830 has a 3 cyl. engine. For some reason I thought the two tractors had the same engine. Would somebody like to explain why Kubota went with a 3 cyl. ? I...

Just curious, I think I've got the largest Kubota that takes the MMM and someday I might get me some turf tires and mower for summer. How does the L series do with a MMM? I'm not planning this for...

Anyone have problems with the retaining bracket on the side arm of the loader wearing through the hydraulic pipes to the bucket? The first time it happened the tractor had 100 hours on it and two...

Well I shot him an offer of $16,650 if he'd throw in a new boxblade and he snapped it up like my dog does a frizbee. Makes you wonder how much room there was on that one. He started at $18,000...

Hi folks, I live on the border of a state so I could save quite a few tax $ by shopping across the line. Here are my choices: 1) Brand new L3830 HST, LA723 loader, L2203 Joy, L2263 bucket...

I was looking today at a L3710 4WD with LA682 FEL, and was quoted 17,900. How does this look? I have not done alot of research on the Kubota. I have friends that swear by them though. I had been...

I have a new 2002 L3710 HST Kubota Tractor with 10 Hrs. on the meter. I’ve owned it since April and have had very little time to play on it. Yesterday I was underneath it just checking things...

Hi all. I recently bought a used '99 model L3710 GST. I noticed (after the purchase of course) that the ID plate on the folding ROPS doesn't list it as being for the L3710 model. It has Model...

I just purchased a new 3710 with hydrostat and a 72inch mmm. I am super happy with the machine except for one little thing. In order for the mmm to run, I have to have the rear pto engaged. By the...

I have a question concerning the mid pto and the rear pto on my new 3710. It seems that unless I run the rear pto, my mid mount mower wont run. This presents a big problem as I dont want to have...

I'm looking at a 2000 L3710 GST w/LA681 loader and removable teeth, 80" box blade, folding ROPS, Ag tires, ballast filled rears, with 105 hrs in really good shape. Seller wants $19,000 for it in...

I am in the final stages of selecting a new Kubota tractor. I have choosen a L3710 HST with R4 tires and a LA682 Loader. My question pertains to the bucket for the loader. All the dealers in...

I've been checking on pricing for a L3710 4wd gst. Local dealers hitting it around $14700-14800 tractor only. Heavy duty 5ft bush hog with 110hp gearbox $1325-1400, and fel $3550-4000. any...

IT WAS A GREAT DAY SUNDAY, A BIG PATRIOT'S WIN AND I FINALLY TOOK DELIVERY OF MY 3710 HST FROM CARVER EQUIPMENT. I WANT TO THANK ALL OF THE GOOD PEOPLE ON TRACTOR BY NET. I HAVE BEEN READING ALL...

I don't want to take away from JohninCA and his Bradco troubles and all the great help he is getting from the list, But I just bought a used Bradco 609 and I need some input from anyone out there...

Anyone on the list using a Bradco 609 backhoe on their Kubota L3710 tractor? How does the tractor handle? Does the hoe work fast enough and does it move the tractor around while operating? I'm...

I have a 2001 L3710 HST. What should it cost for me to have the 50 hr service done and have the Transmission/front axle case oil changed with Super UDT? The dealer I bought the tractor from...

First, I must say that there is a tremendous amount of tractor knowledge provided on this forum. I've really enjoyed reading your comments for about a year now. Well I'm about ready to make a...

I just bought a 1999 L3710 Kubota tractor with a Curtis cab and heater on it. Will this cab be in the way of mounting the Bradco 509 hoe?? I've been reading posts on the list that say the hoe seat...

Anybody out there find a soft cab for the Grand L3710/4310 that they can vouch for? I've seen the generic 1 size fits all but have my doubts. Snow season is approaching, and a cab sure would be...

I borrowed a friends L3710 and woods 9000 backhoe today to dig a trench for a french drain. On my 2910, the governer holds the engine speed within 100 or 200 RPM across a wide range of loads and...

well ... after almost 2 years I'm FINALLY at the 50 hour mark ... actually a luittle more but I was waiting (or rather, not waiting) for the filters and oil to come from Carvers (they were very...

I've been offered a Kubota L3710, FEL, Flail mower, tiller and forks. The asking price is $22,500.00. The tractor is GREAT shape, but it's a bit more than I wanted. If the price is really good...

My new L3710DT should be delivered on Thursday this week - FINALLY! I ordered it with loaded Ag tires, LA682 loader and HD round back bucket w/toothbar, Bush Hog SQ720 cutter with slip clutch...

I went yesterday to the local dealer to have a look at the possibilities of financing my future tractor.My price range was set around the L4300 which gives lots of tractor for the money. Here in...

I noticed hydraulic fluid leaking from behind the piping clamp on the loarder arm. When I removed the clamp the piping had worn through between the clamp and arm and now the fluid is pouring out...

I am looking at buying a Kubota L3710 and am interested in any feedback good or bad. It would have a LA681 loader and maybe a BL4690 backhoe. Thanks.