Everlast Welders - Welders and Plasma Cutters by Everlast

[lilranch2001]

Why do you think they just hired a billion new IRS Agents?!?!???

 

[yomax4]

I'm hoping a new administration creates a billion new unemployed IRS agents.

 

[Mark @ Everlast]

Just got back from the International Work Boat Show in New Orleans. Couldn't spend any green except for tipping...and even once that was only available by some "app".

 

[ArlyA]

I have the cyclone 212es and when I'm welding with power set feature, but I'm getting about 3" of wire after I've taken my finger off the wire button. Kinda drives me nuts and of course there is a chance I changed some setting by accident. I do want it to quit as soon as I stop pressing the wire trigger. You guys know how to stop this extra feed?

 

[ArlyA]

I have the cyclone 212es and when I'm welding with power set feature, but I'm getting about 3" of wire after I've taken my finger off the wire button. Kinda drives me nuts and of course there is a chance I changed some setting by accident. I do want it to quit as soon as I stop pressing the wire trigger. You guys know how to stop this extra feed?

da! I'll call them.
------------------------------------------------------------

• Local. 650 588 8082. ext: 204.
• email: performance@everlastwelders.com.
• Operating Hours: Monday through Friday: 9AM to 5PM PST.

 

[Mark @ Everlast]

I have the cyclone 212es and when I'm welding with power set feature, but I'm getting about 3" of wire after I've taken my finger off the wire button. Kinda drives me nuts and of course there is a chance I changed some setting by accident. I do want it to quit as soon as I stop pressing the wire trigger. You guys know how to stop this extra feed?

Are you running it in 4T mode?

 

[ArlyA]

Are you running it in 4T mode?

I might be! How do I get it out of that mode?

 

[Mark @ Everlast]

Select 2T on the trigger tab. Make sure you select the "std." torch.

 

[ArlyA]

Select 2T on the trigger tab. Make sure you select the "std." torch.

thanks!!

 

[ArlyA]

Finally got this welder in use. Where should I post reports on it?

 

[Mark @ Everlast]

Here or create your own thread on it. You can go to our facebook page "Everlast Welders" or the "Owners of Everlast welders" page as well.

 

[Ken Cunningham]

I am on your site looking to buy the 161sth w/pedal. It does not show the pedal in the what's included section. When I go to check out there is a option to choose pedal for more money. What is the deal?

 

[Mark @ Everlast]

Check out without choosing it. It's a Christmas/Holiday special created for a short period of time. No way to rewrite the whole site for a few day special. Just ignore it, take a screen shot of the page to prove it just in case.

 

[ArlyA]

My Everlast at work. Adding reinforcing straps to my KFI snow plow.

 

[ArlyA]

My plow getting updated! Do love this welder.

 

[5030]

One thing I never do is, I never romance any of my equipment. My wife, certainly but my equipment, never. While I cannot get a close up of your welds, from the distance provided, it appears that you have a penetration issue and the welds appear gobbly. A welder is a welder, brand is inconsequential. Correct welding parameters are however and you are taking an unnecessary chance welding that close to your hot water heater with it's combustible gas supply, something I'd never do. In the shop I own, all welding, no matter what process is far removed from any foreign gas supply. Only takes one 'oops' to cause a major issue or end your existence, whatever the case may be.