Search results

Results 1 to 14 of 14
  1. D

    Kioti K9 winch install

    Here is the answer..... Go to HFT and buy their UTV winch plate, which has a fairlead mount and bolt it on top of the Kioti factory mount. Works perfectly, $5.99, I think.
  2. D

    Kioti K9 winch install

    Does anyone have a K9 with the factory winch mount plate? I can't figure out how to bolt on the fairlead.
  3. D

    Backhoe valve body leak, repair, now real stiff controls

    Willy, I've looked at lots of the literature Nimco has on line including that one (just now). None show my particular valve assembly and none give any torque spec for the bolts holding it together. I also own the CK30 manual but it doesn't cover the backhoe. I bought the hoe manual...
  4. D

    Backhoe valve body leak, repair, now real stiff controls

    Update on this.... (The spools were binding no matter if the tractor was on or off or if the valve body was on the hoe or on the workbench.) Took it back to the repair shop. The O ring that "blew" was between one of the spool valves and the inlet section. The repair guy was unable to...
  5. D

    Backhoe valve body leak, repair, now real stiff controls

    oldnslo, Hard to tell since it's reinstalled but it appears to be held together with tie rod bolts. I can see the ends of 3 bolts on the right ride and I can see where the top one passes through the middle two (stabilizer) valves. Definitely not a bolt however as it doesn't pass...
  6. D

    Backhoe valve body leak, repair, now real stiff controls

    Kioti CK30HST with the KB2375 backhoe. Nimco 1S-5709 valve body Owned since new, 2005. I've had a small leak for several years that turned into a steady drip drip drip, almost a stream. Removed the valve body & took it to a hydraulic shop for a rebuild. Reinstalled and immediately noticed the...
  7. D

    Backhoe valve body leak, repair & now real stiff controls

    CK30HST with the KB2375 backhoe. Nimco 1S-5709 valve body Owned since new, 2005. I've had a small leak for several years that turned into a steady drip drip drip, almost a stream. Removed the valve body & took it to a hydraulic shop for a rebuild. Reinstalled and immediately noticed the...
  8. D

    2375 backhoe Leaky Control Valves

    I've had a leak at the control valves for some time now but recently it has accelerated. I assume there are seals & maybe O rings that are replaceable. Is there a factory manual available? Does anybody have a copy? An exploded diagram would be helpful. Are there any special tools required...
  9. D

    any way to make the rear pto reverse?

    This is probably a dumb question but it would sure be handy every time I hooked a rock with the post hole digger.
  10. D

    electric clutch options for an Ariens 931000 GT

    I suspect my clutch is bad but not sure. I had an ignition switch fail while mowing and then later the interlock module failed when I switched on the pto. Can anyone tell me the specs for one? The factory manual shows the coil should have .3 to .5 Ohms resistance. Mine has 3 Ohms. That would...
  11. D

    Has anyone bypassed the interlock module on an Ariens GT ?

    If so, I'd like to hear about it. So far on mine it runs & I have lights. Working on the pto now. It's a 931014, 10hp gear drive. Maybe 1979 vintage.
  12. D

    Backhoe  valve for rear hydraulic CK30 HST

    every time I take the backhoe on or off I have to lay on my back & reach up with a little wrench & open or close this thing. Is it possible to put a handle on it to make it a little easier?
  13. D

    CK30 sticky throttle

    It seems like I read about this but now can't find it. The throttle does not move smoothly away from idle. Fact is, it sticks and requires force. as a consequence it jumps from idle to 2000 or higher. Not at all smooth. Is there some adjustment to the tension ?
  14. D

    CK30 sunshade & mid PTO

    Does anybody have either of these 2 factory options on their CK30 HST ?
Top