power

BX2660 has thrown a weird fit. Dash doesn't light up (except engine hours). Thought it might be the ignition switch, replaced it, no change. :( Used jumper cables from battery to starter, engine will crank and run if you hold the "start" while cranking. Hard to shut off though (very weird.)...

I know nothing about these. Looking for something like this for mowing. Am I looking in the wrong direction Dependability and ease of maintenance are most important to me. Preserving history and using vintage equipment is something I look for

I need to mark a 120 volt line that runs from the house to our horse barn. If I call our utility will they do that? Or will they only come out and find/mark their underground lines?

Can some one give me an idea of what the average thickness of the shim between the worm gear assembly and the pedestal is on the power steering assembly for a two cylinder John Deere? I tried following the procedure in the power steering service manual but I just can't see how the thickness of...

Hi, Just acquired a dream tractor, Ford 8240, and it needs some repairs (I tell myself I’m having fun working on tractors). Anyways, first on the list is fixing leaking on both ends power steeRing cylinder. I don’t have the repair manual yet (on its way), but curious what needs to be done...

I recently purchased my first tractor, a used LS xj2025h with 1104 backhoe installed. I used the hoe a couple times, and the last time noted the boom floating down in a few seconds. Soon I couldn’t get the bucket to penetrate the ground and the boom would barely come back up. Now the boom is up...

We have a whole house gas generator in our separate garage but it does not have an automatic transfer switch. Not a problem when the power goes out (assuming we're home of course) and after a length of time when we get a notice from the power company that it will be some time before power's...

My mid 90s B7610 has been a 100% faithful workhorse for 20 years. I don't know it's hours as the meter reads 600.7 and that can't be right assuming the last digit is 10ths. I never pay attention to it, just do annual oil changes. Today it lost forward and reverse power. It will move on flat...

Can anyone help me with some advice

JD X485. Power to fuel pump and instrument cluster. No power to starter.

Wondering what people’s thoughts are on this. A friend of mine has been trying to figure this question out due to the additional expense ($8k).

Hello, I was just borrowing a friends TYM T474 and everything was working great this morning, I stopped for lunch, but this afternoon I took it down my steep driveway (16% grade) and all of a sudden it had no power to back itself up that it backed up easily that morning and for a week prior...

Stop Error On T4.75, Low Power Steering Pressure / Transmission Pressure 2019 Powerstar 75 Symptoms Day started out with all running good, no apparent problems, then STOP error comes up along with a symbol on the display that closest resembles the low pressure, and steering wheel. However I...

What is the procedure for bypassing hydraulics on a 2000 power trac pt1850. I need to pull it to my shop.

I replaced the power steering cylinders on each side of my Ford 3400 and finally started up my tractor to test it. Bubbly oil started pouring out of this pop it behind the steering column. Anyone know why or how to stop it?

Does anyone have a power broom for their Power Trac and if so how does it work for removing light snow and also for removing gravel from grass along driveway. I have considered getting one if they would work but they are expensive for just occasional use.

He said talk me out of an excavator, I said get a Power Trac first. https://www.tractorbynet.com/forums/threads/talk-me-out-of-an-excavator.550971/page-10#post-7094723

I have a 2016 New Holland Boomer 47. It has 4 ranges with a four speed transmission and shuttle (f-n-r) driver on the column. When increasing the gear ratio, particularly in 3rd and 4th range the tractor bogs, slowing way down. The motor does not drag or decrease RPMs, just the drive portion...

Howdy See if anyone knows what this means If I step on the accelerator hard sometimes the green “ calibration “ icon comes on the dash and I lose all power u till I take my cot off and wait for it to go away after about 5 seconds…. Super annoying Anyone know what the deal is with this…thanks!

Needing help. I have a 2018 cub cadet challenger 750. I had to replace the starter gear due to a couple of broken teeth. After putting it all back together, I am getting absolutely no electrical power. I have checked the battery and it is good. I checked the fuses in the fuse box and they are...

After replacing a sync reverser and now have lost 2 gears I want a compact utility tractor with a wet clutch and power reverser. Don't want hydrostatic. Most of the Korean, Japanese and Indian tractors I have researched use a dry clutch and a sync reverser. Is there a specific brand that uses...

Hi folks, after looking at wood splitters as per this thread: BCS branded wood splitter? I have been wondering if anyone has set up their tractor to run a splitter or other implement that would be freestanding but utilize the PTO via an adaptation to link to the hydraulic pump. Since the pump...

Yesterday I stopped in at a TYM dealer and the salesperson said the 574 could have up to 3 rear remote. 2 were standard. I said that sounded great so I could have tilt and turn and a hydraulic top link by getting the optional remote. He said that when a customer gets a backhoe one of the rear...

Can I use these ports for power beyond for mid mount loader valves or do I have to add a block to the rear scv bank? 2011 with IVT and TLS

Mahindra emax 25L HST Cab I have some intermittent power issues with my cab accessories (front wiper, washer fluid, work lights on front, work lights on rear, blower for cab heat (just the blower)). The issue doesn't seem to effect the lights build into the hood of the tractor, the 4 way lights...

My diesel B3200 HST has developed a problem this year while mowing. After it heats up, it will suddenly lose power, RPMs drop down, and it almost stalls out. If I let off the accelerator, the engine eventually picks up speed again, and a puff of white/blue? smoke comes out of the exhaust. Any...

Anyone buy a DR Power brush mower? Have lots of weeds, scrub along a creek. May take a Year to clear it but their mowers look interesting. I like the self propelled models with electric start and power reverse...

Kubota #GCK60-BX Leaf and Grass Catcher with 3 Bags. Was on a BX1870 with 54” Deck and manual lists for a BX1800 or BX2200 with a 54" or 60" Deck. Comes with an extra PTO case and homemade wood stand for storage. Unit works perfectly. Just want to free up some garage space for winter.

Who sells a repair kit for a 445A steering shaft, the bearing/seal under the steering wheel?

I'm upgrading from a single 2000lb axle 4x8 tilt utility trailer to which I've added a 3500lb winch for tilting the bed up to 45 degrees for dumping the load. The power comes from a 50amp Anderson connector at the pickup rear that that connects to the pickup battery with a 60amp circuit...

Hello I visited this forum and others looking for help with my Mahindra with the above symptoms. Due to circumstances beyond my control, my tractor sat for almost a year. I changed the all the oil/air filters, but the tractor was still is bad shape when I started it up. Very rough idle, with...

Newbie here. So I changed out the infamous neutral switch and figured I'd update the key switch/ignition as well. Went slow, so pretty sure I did it correctly. Battery is strong, checked the three 10-amp fuses, all new. But I get zero juice to the fuel gauge or anything else, not even a click...

Hello, new to the forum I recently bought a 2004 Massey Ferguson 461 with 800 hours. I am having an issue with power steering. At times, sterring gets really hard while using it. My question is is there a way to check/add power steering fluid to a 461? Thank you.

Hi, I am a new member. I have had a TYM 353 from new, for about seven years, and I really like it. For the last two years, however, I have had a persistent problem. I experience intermittent power loss under load or on a minor gradient. I use the unit regularly to haul a light trailer and to...

John Deere Pwrflo 48&54 mowers S# M00PFCD296184 new bearing, skid patch added on bottom of blower, includes bracket for chute deck mount. Pictures show back of mower where unit mounts. Call JD dealer for models it will fit. Came with my 345 and I don't have leaves. $125.00 O.R.O. Message me...

I am not certain what to make of the current symptoms I am having so I’d like to ask for your experiences and thoughts. Circuit breaker is on and when I flip the pressure switch the gauge jumps to 20 on the spot then immediately returns to 0. Does that indicate anything to anyone? To me, that...

I have a 2010 3038e and am getting ready to install a diverter to add a 3rd scv to the rear (already have JD 4th & 5th) and was looking at how to source switched 12v for the solenoid. While looking at the fuse box & considering using an "add a circuit" fuse plug-in I found that power was...

Hi, for a few weeks now when I take my tractor I lose power especially on an upgrade. I changed air filter now the fuel filters and I tried mowing. After 20 minutes I had to drop a gear. Won't pull itself ahead. If i kept on I'd have to jeep dropping gears and up the pto . Barely crawling. Then...

I know this has been discussed in various threads but I'm looking for a good solution that I can implement in 2-3 locations where my sensitive electronics are located while running the whole house on a Duromax XP1200EH. From the reading I've done here and on the web, I know an online double...

My compact 4wd tractor loader has weak lifting power. I've owned other tractors, and they lifted much more. The bucket can tilt and lift double what the arms will lift. I've opened the knob that slows the flow to the loader. Any ideas? I have several items needing moving that it won't lift.

I have a Ford 3610 tractor shooting power steering fluid out of the reservoir and leaking out of the cap, when I fill it up it steers fine just ends up leaking all the fluid out, also it’s frothy fluid see videos attached. I’ve ordered a new filter and ORings just want to make sure the pump...

trying to figure out electrical issue in a T2210. The #6 fuse blows as soon as the key is turned on. 6 is for the aux lights and aux power( cigarette light). All the wiring looks fine. No damage. If the 11 relay is bad, will it blow the fuse immediately? 11 is for aux work lights. My lights and...

This question has probably been asked before, so I apologize in advance for any redundancy. I recently sold my old tractor and now have a new 2024 YT359C. I’ve installed the radio and some other accessories, and I’m considering adding a camera at the back and one at the front for loader work...

Massey Ferguson96 231 power steering fluid going some where.

B7800 with 600 hours once the tractor gets hot it will have a power loss as to where even driving it you have to take it easy as the RPMs drop if you push the peddle with nothing running. Take your foot off the peddle RPMs go back up. This B7800 has always ran hot once it gets close to the red...

I thought to look at the sight glass on my pressure washer pump and it had enough but looked milky. Sure enough it was. It’s probably about 15 years old and I’m guessing I’ve changed it once at the most. The manual says every so many hours or every 3 months. I’m not going to change it every...

I am an Automotive Instructor at Tech School. We recently had an 86 S1900 donated. It has 2 brand new batteries in it but I have no power at all. At first it lit the oil pressure lamp but now there is nothing. Heavy trucks are a bit out of my wheelhouse so I could use some help in knowing where...

How to stop power takeoff from running while driving

The second EPS unit failed on my Cub Cadet … first covered under warranty… now this $1,000 replacement is on me …. thousands are failing around the country yet there is almost no info on them … strange … the issue is these tractors are barely worth $1,000 and I hate to throw the baby out with...

Hello, I have a 2005 or 4 Terraplane 38hp tractor. Made in China. I've been using this tractor for about 4 years or so (wish I had bought a new one), and have performed a few repairs on the hydraulics (pump ruptured and spilled hydraulic fluid into the engine oil reserves), and now I'm onto my...

So I was thinking originally of running a power beyond loop to the rear of the tractor but, I want to be able to run front mounted implements like skid steer stuff as well. I could run it and just have it self looping at rear for things and just undo how I run it and switch it around manually...

My father-in-law left me all his tools and equipment. So i have aquired a Power Track 450 LT chineese mini dozer. Its an early 90 model with 2 cyclinder diesel in it. I cant seem to locate the oil filter. Also i need insructions or a manual on how to adjust the foot pedals for clutch and brake...

I have a MF 135. see pics for name plate on the tractor. I was told it has "assisted power steering?" Any way, a mechanic told me this. I think it needs some more hydraulic fluid for the assist. I have an owner's manual, but I can not find the location of the fill port. I looked at the...

I have a BlackMax Honda powered power washer; I replaced the entire pump assembly two years ago. The other day the housing that the garden hose threads (inlet tube) onto broke off. I ordered a replacement; it took me about an hour with a pipe wrench to get the old one off/out. Installation of...

Thought I would start a specific post for this to follow my build. Here is where I am at this point. Bought the powertrac adapter plate directly from powertrac. This plate is for a Powertrac 1460: Bought the 3 pt hitch to ssqa adapter from Amazon. Starting to line up the adapter plate to...

Tractor **** off when running, would not start, no power to ign switch, found f1 fuse blown replaced and popped again immediately while switch was turned on , turned switch off, replaced fuse and blown a second one when turned on, pulled console, and removed switch, replaced f1 fuse, no power to...

As I get deeper into this farming thing, I’m adding more powered equipment in the cab. I have a nav system, camera system, bail thrower controller, and now a hay preservative system. Everything takes power, and I don’t want a rats nest of power leads coming from the battery into the cab. How...

I got tired of having to pop the hood every time I wanted to connect alligator clips to the battery. Cigarette lighter sockets used to be a convenient place to tap into 12V power, but many new vehicles don't have them. They are also limited to less than 10 amps and often controlled by the...

I’m installing a 3rd function hydraulics to operate a grapple. Could someone tell me where the power port is located on a 2016 John Deere 3038e? Thank you!

Been trying to revive an old 8N after sitting for 7 years. 6 volt, with front mount distributor. Have replaced a fair bit of parts, new gas tank, fuel line, sediment bowl, and all 3 screens. Passes fuel flow test from carb without problem. New points, condenser, distributor, square coil, and...

Hello. I'm looking to put a needle flow control in the line going to my loader. Kubota MX5200 with LA1065 loader. My thoughts are to go with a 3/4" valve for the purpose of throttling the speed of loader functions way down when me or the mrs's needs to be in a basket on the forks to reach high...

My 5320 solenoid won't engage or spin the starter, I started to start it the solenoid engaged I let off it and thought I smelled a small burning smell then went to engage the starter only a very weak clicking then nothing, the positive post on the starter tests almost 14 volts, when I turn the...

My power steering hose at the cylinder split yesterday. I'm unable to locate a replacement. When I search I only find hose for 231,240. Can someone help me locate replacement hydraulic hoses for a MF230? I see that under the battery area I looks like the lines convert to metal going up into...

The jd 1020 gas serial79000 won’t crank sometimes after being shut off. Doesn’t show any lights on gauges when put in accessory position I have jumped the safety switch with no results. Did a continuity test on all wires. They show good. Checked continuity on ignition switch in all positions...

Greetings after 2 years of nothing but disappointment with the workmaster 75 between breakdowns and PTO issues which I've had another threads I figured I'd start a new thread to ask some questions about the new Power Star 120. If anyone out there has one I love to know if you know the interior...

I have a 3 year old L3301 that I use primarily for brush hogging and plowing. I noted last week when moving from in job to another I had significant power fluctuation. I did not note a drop in RPM, just that I slowed down to a crawl, even with HST pedal floored. I tried low, mid and high range...

For the last couple weeks I have noticed my bucket coming up slower and with my forks attached to the bucket it tends to come down when the tractor is off. Recently even if the tractor is running it still wants to lower itself. It does not raise as high as it use to and it lift capacity is much...

Help me find a powershift pump shaft #194310-24430 for YM 276 D new or used. Nothing at Fredericks... Thanks

I have a Mahindra 3016. It looses power whenever I put a.load on it. Does not run hot, but worsened the longer I run it. Uses much more fuel than usual. Any ideas?

My JD 5320 is gradually get worse when you put it into Park. Not an issue if you’re on mostly flat ground, but if on a slope and you put it in park most times it will start to roll. When it starts to roll a clicking sound can be heard. If I have to park on a slope I always use the front end...

Help me find a powershift pump shaft #194310-24430 new or used. Nothing at Fredericks... Thanks

First of all let me impress on you all that I am NOT gonna change how much fuel my injectors deliver. I am not gonna fiddle with my engine. So, I have a YM2310 that runs well and only smokes, and then not very much, when I accelerate quickly. When at full throttle and under load it doesn't...

I am not sure if this is the correct Forum but it is Chinese Engine Question. 739cc Rato V Twin, Honda Copy, same as Power Ease PN R740D-8, and many other names like Predator. Many of these Mini Chinese Machines are coming with the 23hp V Twin Engines, some with 420cc RATO 13.5hp Briggs...

I've looked all over and there is no information about whether the Ventrac power rake can be pitched to cut a crown in a driveway, etc. Can anyone confirm if this is possible?

can a 2.2 Gal. per minute 12-Volt pump on a 3 pt sprayer (Workhorse 40 gal 12 volt with 5 nozzle boom for utility tractors) be powered by a 12v 35Ah rechargeable battery? This sprayer has not yet arrived but I already know the wiring harness is 8 ft long and will not reach the battery in front...

I built a 12 x 20 ft woodshop inside my new pole barn a few years ago. Just after I finished it, I noticed this big heavy dining room hutch out by the road for garbage pickup, just around the corner from our place. It works real nice for storing my power tools. The shelf’s are made from...

My dealer is baffled by this problem, they had the tractor for almost 4 weeks. I guess a computer update was supposedly the cure. It was returned to me and was not the cure. I want to stress the time(s) in the video that the occurrences happen. My MF 1740M has plenty of power and torque until...

I am requesting someone in the Northern California area near Auburn allow me to compare one or two items on your tractor with mine. My tractor was disassembled and I am trying to piece it back together. I didnt disassemble it, I just own the tractor and Im trying to get it up and running again...

Hey everybody, My JD X749 w/ Yanmar engine is giving me fits. The starter has been finicky for about a year being reluctant to turn over. It seemed if I finessed the key as I was tuning the key it would finally engage. Assuming it was the switch I changed it out without success, and continued...

I have a JD 5310 Tractor that’s been losing power to the wheels after running normally for half an hour or so. The tractor sat all winter and I just started using it today. After running normally for a while, even though the tractor is in gear, the transmission loses power & the wheels don’t...

A couple of weeks ago I noticed that when using the MMM the mower would not fully stop turning (it was turning at a reduced speed) after disengaging the PTO. It would only stop after throwing the mid PTO selector ever to the off position. Then after attempting to move the mid PTO lever to the...

Curious what you all do to be prepared for a long term power outage due to weather, grid damaged by whatever. I've been telling may family to be prepared in the even of a sustained outage (longer than a month or two). I don't feel sufficiently prepared for an outage that long, and I know my...

I have an L3540 Hydrostatic 4 wheel drive tractor, have had it maybe 8-9 years. This problem seems new or has been slowly getting worse and I'm just starting to notice it.. When I have a mower on and either going on flat land or downhill it seems to be fine, BUT on even a slight upgrade I seem...

Does anyone know if the power from the A1100N2 in the 2400h can be turned up by adjusting the screw on the injection pump?

My tractor sat for a couple of months. When I went to use it, it has no power to the front bucket. I can raise an lower it but only if its unloaded. 200 pounds in the bucket and I can't raise it. I s there a relief valve that could be passing fluid?

Gday I am working on a Ford 4000 with a power steering assist Ram on it the owner pulled it off and took it to the local shop to repair leaks when he got it back it didnt leak but oil gets very hot within 30 minutes too hot too touch! I have played around with adjustment and it all works well...

I can raise my bucket and tip in and out, but have no "power" to lift front tires off the ground. I replaced the pump (truth is I wanted one on the shelf anyways), no affect. Everything else looks good, no leaks, fluid/filter good. Kinda thunkin it may be an internal seal somewhere that...

Ls 3037 2017 model. Blowed 5 Amp fuse that controls dash power . Tractor went to limp mode would not regen. Disconnected battery over night started and tried to Gen and it would not shut hood then no power . Dead short in that circuit. Can you by pass fuel solenoid to drive on trailer...

Looking for advice as how to proceed, steering loss was after repairs to front axle. Had leak(s) at front axle, left side was seal at “knuckle.” Right side replaced: knuckle seal, final drive outer bearing and seal. Job went well, even for my experience level; no stranger to busted...

took out of barn today and after it warmed up, the Power shuttle high/low alarm light would blink red. it would blink 3-4 real quick then do a steady 4 then a steady 9, I assume that is a code 49? anyone help with this?

Is a subcompact under 25hp engine enough power to maintain a under 15 acre property where the tasks are mowing w/ mid mower, finish mower, brush hogging, stump grinding, hole digging, box blade and typical loader work? I have owned a 35hp and 50hp so I'm a little uneasy getting a under 24hp.

Hi from a German Yanmar Owner, I've been reading here and at the Hoye forum for a couple of years now. I own a YM1510d since 2020 and I'm very happy with this little powerful tractor. I bought the tractor from a dealer who mounted already a FEL. Back in 2021 I updated the maual steering to a...

I can start tractor snd sometimes ut will go really sluggish even when idled high off the granny speed. Acts like it’s almost going up a really steep incline even when flat ground. I have checked all levels look fine unless im missing something. The manual i have for it doesn”t make clear the...

I'm trying to run a Ventrac KA160 Blower with a 430 Max power unit. The 430 has the air-cooled Kohler. The Ventrac manual specifies a B52 belt however, that belt is too loose even with the adjuster turned all the way for max tension. Is there another belt beside the B52 that I should try here...

The loader jerks really Bad when the oil is hot . I have replaced the pump, loader control valve, relief valve, change filter and oil ,replaced all suction hoses on suction side of pump ,changed the quick couplings and switched the hoses on the lift and replaced the cylinder packing . Installed...

I have rebuilt power steering pump and steering column and still will not turn what what could be my problem? I have not put a pressure gauge on it yet. Ford 545

Hello. Does anyone here own a B7100? I'm wondering how it does with pushing snow, loader work, rear blade. Is it underpowered? Also, how much trouble is it to find parts? Do you get them directly from a Kubota dealer or is there a reliable online source? I'm in Canada.

I recently began having problems with my Workmaster 75 feeling like it was down on power. It's mostly noticeable when I'm pulling equipment on on an incline. It has a hard time keeping up RPMs and if I'm in a higher gear range it really struggles. I contacted the dealer who came out and did a...

Power steering pump is leaking between the rear plate and the housing. The seal kits are discontinued. And it's an odd shaped seal. Any chance some good rtv on the flat bit will work? I have attached pics of where it's leaking in the yellow circle and a pic of the plate off and the seal.

my north track 254 tractor the steering is hard, one way and then eases up in power steers properly. When you go to steer back, it locks up again. I’ve changed the oil clean the screen have flow to the piston. I took the diverter valve apart and cleaned it everything seems to be good there. all...

So me and my neighbor use a 1970s era Massey 31 industrial logging tractor it has a new power steering pump (gear drive off the front gears of the engine) new hoses and cylinder, it steers fine when you first fire it up and take off but once the engine and pump get warm you have to lift the nose...

Hi there, everyone. After looking on the Power Trac website I saw how they had a display at the VA farmshow many years ago ( probably 1980's), and I was just wondering if they advertise anymore. I'm under the impression that they don't advertise at all, but maybe I'm wrong. Thanks.

I have an LS MT342SH with Cab and have noticed reduced power when driving in reverse. I wonder if this is normal or an indicator of a problem. I run the engine at 2000rpm and am in 4-wheel drive when working it. Recently, I was removing snow on my steep paved lane (10 degrees at steepest point)...

I have a BCS 853 with a Honda engine. We've been getting a ridiculous amount of snow, and I was snow blowing with it and it gradually kept losing power - the snow was being thrown a shorter and shorter distance, until eventually it won't even make it out of the chute and it clogs up. At first I...

Hello this is absolutely my first post on anything that is that is the World Wide Web. Just wanted to put some sort of ad and let you guys know that I’ve got a pretty big inventory of mostly Mitsubishi and satoh NOS parts still in factory packaging. Mostly mt160 mt180 and beaver 1 and 2 but also...

I have an eHydro John Deere 4210, the last three times after 45-60 minutes of mowing, with a 5' shredder, in not particularly deep grass the machine will start to bog down at the slightest challenge. I have not let it die but I am sure that if I kept my foot on the pedal it would have. Runs...

I have an 1835MHC that I bought this past spring. It is used 80% of the time for mowing. I generally leave the loader off for easier trimming next to objects and only attach it when I need it. I have noticed that with the loader installed that my power steering loses quite a bit of power...