Engine ideas

   / Engine ideas #251  
I've not put one on a L yet but the bolts and handle bars hook at the same place up front.
So I think I can make it nearly like a 10 and later models.

Looked at my L again and determined that if I moved the engine up closer, the muffler would hit the left handle bar first followed by the gas tank which would hit the hi/lo and swiftamatic rods, not the right handle bar. These rods could be bent out the way without too much difficulty. Would love to see pics when you do an L.
 
   / Engine ideas #252  
Looked at my L again and determined that if I moved the engine up closer, the muffler would hit the left handle bar first followed by the gas tank which would hit the hi/lo and swiftamatic rods, not the right handle bar. These rods could be bent out the way without too much difficulty. Would love to see pics when you do an L.

Yelp The L model ??????:confused2:
I plan to try to do a L as soon as I get through Two swap meets.
You Know more about them then I do on them.
I look at things strange some times.
I have in my mind what I want,
But some times it don't come out that way.
 
   / Engine ideas #254  
Hey One.
Is the tractor still doing its stuff?

Yeah. Now that its repowered I have to fix some oil leaks - both axles, axle housings (where the 6 bolt castings attach to the main body), and the swiftamatic shaft that goes into the right axle housing. Might do some this Fall and some next Spring. I'm in no particular hurry...
 
   / Engine ideas #255  
Hey One
Are you going over to Richard's swap meet Sat?
I would like to see you in person.
I plan to be there.
 
   / Engine ideas #256  
Hey One
Are you going over to Richard's swap meet Sat?
I would like to see you in person.
I plan to be there.

Not sure yet. Would like to go but there are some complicating factors like my 30th wedding anniversary. Will know later in the week.
 
   / Engine ideas #257  
Not sure yet. Would like to go but there are some complicating factors like my 30th wedding anniversary. Will know later in the week.

Looks like I'll be going after all. Hope to see Bruce and others there.
 
   / Engine ideas #258  
I am in Pittsburg Pa.
So I plan to be there tomorrow
I also brought the new Gears with me.
I didn't bring a tractor or engine.:thumbsup:
 
   / Engine ideas #259  
Went to the swap meet today in WV. Got there late so I missed Bruce who was apparently there earlier in the day. Talked with Richard and he said Bruce was there and showed him his gear which could be used on an L repower. Show was fairly small but if you needed parts there were plenty to be had. There were other things going on too: a tractor pull, hit and miss engine dispay, a couple of nice David Bradleys, and if that wasn't enough - there was a quilt show. Picture perfect weather!
 
   / Engine ideas #260  
I was there and now I am gone.
I stayed until about 2.30 had to get back to Pittsburgh.
For a surprise birthday party for My son.
Sorry I missed you maybe next time.
 

Tractor & Equipment Auctions

2018 Allmand Night-Lite V-Series S/A Towable Light Tower (A49461)
2018 Allmand...
Toro 30495 Groundsmaster 7200 72in Zero Turn Mower (A48082)
Toro 30495...
PALLET OF TARPS, UMBRELLAS, AND PORTABLE SHADES (A50854)
PALLET OF TARPS...
2020 CATERPILLAR 289D3 SKID STEER (A51242)
2020 CATERPILLAR...
2008 FORTITUDE MANUFACTURING 40X96 FLATBED (A50854)
2008 FORTITUDE...
16 STEEL SHEETS CURVED (A50854)
16 STEEL SHEETS...
 
Top