Mounting tire chains

[MinnesotaEric]

I put chains on one tractor yesterday, there are lots of ways to mount chains I thought I would share the easiest way I have found to do so.

1) lay the chains out with the outside, the ground contact side facing up
2) tie a short cord to the side chains, the length will depend on your tire size, on mine I end up with a V shape about 3 feet.
3) back up to your chain, take the cord and hang it on the tire treads.
4) drive forward slowly, stopping to spread the chain out on your tire.
5) continue doing this till you have rolled the chain up on the tire and have working room at the rear of the tire
6) your chain should be well centered on your tire and have very little slack.
7) fasten your chains.
8) step back and check out your work

View attachment 579186 View attachment 579187 View attachment 579188 View attachment 579189

View attachment 579190 View attachment 579191 View attachment 579192 View attachment 579193

View attachment 579193 View attachment 579194

This is the easiest way I have found to do chains, if you are doing this in a shop and can jack up a wheel it works good than also.
On the smaller tires I have jacked them up and chocked the other side to do this, then simply kneel down to do the fastening.
If you find that your rope V is to long when the chain is started up simply stop and leaving your other cord on run a new V and snug it up remove the old and continue. Using this method one person can install heavy chains on large tires. Without straining and hurting themselves. If you take your time after using this method a few times you will find that after your chains are laid out and untangled you can mount them in well under a half hour each with help spreading the chains accross your tire and telling you when to stop it's even easier and you are not fighting with the weight of the chains when fastening the side links.
The shorter the V that works for you the easier to line up and fasten the side links with all the slack taken up by the chains, no fuss no muss.

This is most certainly not the only way, but it is the easiest way I have found.

Lou

I have no idea why these pictures all rotate when I post them.

I put my chains on over a period of a month because I was able to find good excuses to ignore the tire chains. Made it super-easy to pace myself (heh, not really). If you count how many times the hammer moves, that is how many links I had to change to fit just one chain.

 

[LouNY]

Did you consider disconnecting the hooks going tothe side chain and shortening them a link or two on each side.
Also when I use a clevis in the tire chains I try and rotate the excess up so the clevis pin is on the end of the link.
My tires are a bit larger then yours and i think that makes them a bit easier to chain up,
I very seldom use any thing to tightnen them up, I just pull the center chains together and put the clevis in them.
Then I fasten the side chains and then pull the center chain out and down to the side chain and secure them.
Then if too loose I will try and get an another link in the side chains.

 

[dnw64]

I put my chains on over a period of a month because I was able to find good excuses to ignore the tire chains. Made it super-easy to pace myself (heh, not really). If you count how many times the hammer moves, that is how many links I had to change to fit just one chain.

Wow, lot of work!

BTW, the manufacturer of my chains (OFA) tell you to not get them too tight - and actually provide a picture showing there should be some chain hanging slack. See at about 1:30 in this video:

 

[LouNY]

Well heck Sunday morning just sitting here drinking coffee and reading this, started watching the different chaining up videos.
Some good ones and then so many filled with miss advise and showing the harder ways to install chains and the obsession of some with getting the chains tight.
Many of them working way to hard for what should be a moderate job.

 

[grsthegreat]

I never have installed mine tight. Never have had any issues ....ever. I do have a set if tensioning springs on mine and that helps prevent any issues i feel.

 

[MinnesotaEric]

Wow, lot of work!

BTW, the manufacturer of my chains (OFA) tell you to not get them too tight - and actually provide a picture showing there should be some chain hanging slack. See at about 1:30 in this video:

I do have some slack and I showed that slack in the video. What I clearly needed to do was get the inboard chains to stop rubbing on and grooving my steering knuckles or the knuckles would quickly break and fail. I thought I made that point repeatedly and clear.

I guess I did not.

The tightening of the chains was because I made each chain about ten links too long after narrowing the chains so they wouldn’t screw up and destroy my steering knuckles.

 

[MinnesotaEric]

Did you consider disconnecting the hooks going tothe side chain and shortening them a link or two on each side.
Also when I use a clevis in the tire chains I try and rotate the excess up so the clevis pin is on the end of the link.
My tires are a bit larger then yours and i think that makes them a bit easier to chain up,
I very seldom use any thing to tightnen them up, I just pull the center chains together and put the clevis in them.
Then I fasten the side chains and then pull the center chain out and down to the side chain and secure them.
Then if too loose I will try and get an another link in the side chains.

I needed to narrow the chains, not tighten them.

 

[LouNY]

I needed to narrow the chains, not tighten them.

What I was saying is to remove a couple of links on the section of chain that runs down to the outside rim chains,
that will effectively narrow your chains with less work and the center grip chains would have stayed spread further apart.
I am refering to the hooked links that fasten the traction cross chains to the outside or rim chains.
It's a bit late to do so now.

 

[dnw64]

I do have some slack and I showed that slack in the video.

I did watch most of the video, but must have missed that.

When I saw showing a little slack slack was when you said that you were going to try and get it out. Also that you had put the chains on with 0 air pressure so that they would tighten when you re-inflated. Not trying to be critical, just put some additional thoughts out there. If you don't feel you need them, please ignore.

 

[MinnesotaEric]

I did watch most of the video, but must have missed that.

When I saw showing a little slack slack was when you said that you were going to try and get it out. Also that you had put the chains on with 0 air pressure so that they would tighten when you re-inflated. Not trying to be critical, just put some additional thoughts out there. If you don't feel you need them, please ignore.

For video editing reasons, some things are out of order, like my opening scene. The big idea is that I’m narrowing the chain to fit my front wheels because the OEM wider configuration was sawing into my steering knuckles. When narrowing the chains, I also made the chains way too long. The chains are heavy enough that I used a small binder to take up the slack. I also used four shackles on each side to secure the chains together and fencing wire to secure everything.

I’m amazed at the second-guessing going on given that now the chains fit perfect, work perfect and while loose enough to move a little bit, clear the steering knuckles even on turns while in four wheel drive which tends to try to walk the chains into the steering knuckles.

Guys, I’m a master mechanic. Cut me some slack.