deere

Hello Everyone - Friend has a 955 and is looking to purchase a front broom / sweeper. He has a front blower with tractor quick attach - yet to put on but has the complete set up from what I can tell. From what I understand, the 246 broom was the model for the 955 (55 series tractor). I...

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

Back story on tractor is I did a rebuild on it new pistons, rings, rod bearings and head gasket. Flushed radiator new thermostat adjusted valves. I got it back together and it will start but it just seems like it has no power and I’m pretty sure it’s getting to hot also it won’t idle has to be...

Two questions: I have a commercial-grade JD Zero Turn mower that I use to mow my rural property. It was purchased in 2012 and has 870hrs on the clock. It is serviced regularly and is in excellent shape. The dealer says that it is time to replace it because JD is discounting the 2023 models, and...

I have a 1986 John Deere 650 tractor. it is currently stuck in 4x4, the shifting handle just free wheels like its not hooked to anything. the roll pin in the handle is good. Can I pull the shaft that the handle is mounted on? I am assuming that the shaft it broken or what ever it was driving...

The tractor has been sitting all winter, and now it won't turn over. The solenoid gives a loud clunk, but that is all I get. No hint of a starter problem before this. The battery is good at 12.7V at the starter. Tried shorting across the posts on the starter, and got nothing, so I'm thinking the...

Need some help in figuring out why my front loader will work, however not at strongly and will lower without contant monitoring, while 3 point will not go up or down....changed filter, not leaking hydralic fluid....any suggestions? Thank you, JMS

Hello All, I have recently bought a 1966 John Deere 4020, got a screaming deal on it. I am hoping to find a loader for it. I have seen that John Deere Loaders 48/148/158 do fit and work. I was able to find a few 'fairly local' but the asking price is higher than I paid for the tractor. I am...

I started a rebuild on my little 850(yanmar 2500). Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the...

I started a rebuild on my little 850. Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the middle cylinder...

Bought a 301A over a year ago that had been setting along time turns out all I needed to get it started was a new fuel transfer pump and rebuild the starter ….... everything seemed to work well except the rear lift arms wouldn't hold a middle position no biggie ran for a bit but I noticed was...

Quite simple to replace the seals.

Probably not the most apples to apples comparison but I have been looking at new tractors for a couple of years now and getting closer to pulling that trigger. I have looked at and drove most fo the current brands out there. LS was far from my list of tractors when this started. However, there...

I just recently bought a John Deere 850 for a super cheap price compared to what the market is in my area. Everything seems to work as it should and it seems pretty clean. The only issue I’m having with it is it seems to have a slight miss to it around 2,000rpm not sure what it could be I’m...

I purchased a 5520, the instrument cluster is not working. I sent it to be tested and it works fine. I've had a mechanic work on it extensively with no success. The cluster has rpm, fuel gauge and temperature gauge. I'm considering just adding aftermarket fuel and temperature gauges. I'd love...

Hello My frontier RC2060 brush cutter has started to feel a little odd, .. more than usual vibration and noise during operation and a tendency to sometimes shave dirt even when the cutter is not at the lowest position . On inspecting the cutter, 1. I can see a thin film of oil on the underside...

I know there are a couple other threads on this, but wanted to help contribute: - Proof of Concept - LED POC Test Video Quick video showing reflector cutout and LED Fitting. Reflector Cutout Fitting LED and Controller Test Confirm, then order second set of LEDs There was a logical cut...

Having an issue with my 6410. The problem began with the reverser not working correctly, it would only go into reverse and when I put it to forward it also would beep and go in reverse. I shut it down and now nothing happens when I turn the key to start it. It appears that it thinks it's not...

so she cranks but wont fire! I found she isn't getting fuel because after some testing without luck I finally decided to put gasoline on a rag and cover the intake with it and she fired right up. This tells me it is getting everything but fuel. I noticed I wasn't hearing the click as usual from...

I’m wondering if I can some initial thoughts on what might be wrong with our Deere 110TLB engine. Engine has about 1500 hrs. on it - it has always sounded terrible but never had a performance problem. I was going up a steep hill when it suddenly lost power and it conked out. When I tried to...

Information to post and pass on. John Deere Deluxe SCV Coupler updates John Deere Hydraulic Quick Coupler Socket Replace in pairs Deluxe SCV valves new coupler design 2 x John Deere Hydraulic Quick Coupler Socket - AL221083 2 x John Deere Clip - L158630 2 x John Deere Hydraulic Coupler Sleeve...