deere

I'm trying to repair the reverser in my 301a. I found the front seal completelty shot, and a bigger problem. For whatever reason, the clutch pack is digging into the front housing. (pic below) There are no thrust washers or anything in it. Also the center hole where the seal goes is a good...

Hey all, this is my first post but i have gotten many questions answered by just reading different post/answers for years now. hay season is quicky approaching us and i was looking to get a little more hp out of my John deere 5420. to my knowledge the only difference between the 5420 and 5520 is...

I have a JD 5205 that won’t turn over. Turned key on and jumped across solenoid and it turned over but didn’t start. Any suggestions.

Does anyone know of any aftermarket cylinders that would work to replace the cylinders on a Deere 390 front blade. I rebuilt mine 2 years ago and the barrels had rust pitting from water laying in the bottom for 28 years. I honed out the barrels before I rebuilt them, but they were far from good...

Hi My tach on my sx3100 stopped working. I assume the cable broke. Does not look like I can get new cable from cub cadet. I believe John Deere 2720 is the same machine. Does anyone know is the cable is the same? Has anyone changed these, what is procedure for remoy dash to do it? Thanks

What hydraulic pressure gauge do I need to measure hydraulic pressure on my John Deere 3032e FEL, I have to unscrew the hydraulic line and hook up a gauge to it but it seem’s like it is metric threads, any ideas would be appreciated.

Hello, I have a John Deere 790 that the bucket lift that bleeds down after being left up. I had all 4 cylinders rebuilt in hopes this would solve the issue but it hasn't. I am also assuming he actually rebuilt them since it is falling at the same rate before. There are no leaks anywhere on my...

I have a John Deere 4410 compact utility with E hydro.When the load match is off the tractor acts normal. When I switch on the load match switch the tractor moving speed slows and is sluggish……Someone told me it could be a sensor that is on transmission and one on bellhousing of engine?? Any...

I'm considering a John Deere 4510 Tractor. Any thoughts on this tractor? I found a nice used one and may look at it tomorrow.

I bought this a couple years ago with this problem and I'm just now getting back around to fixing it. It works great in reverse but in forward nothing at all. It doesn't even try. I'm actually suspect of the valve block because it's cover is leaking a bit. It has a homemade gasket but it looks...

Hi all, Going to purchase either the commercial 7' or 8' road boss grader to go behind my 5115M. The website lists the following for the specs and I'm having a tough time making my decision. The rear wheels on the tractor are set to 82" exterior to exterior, so I think the 7 footer would cover...

Aftermarket Hood New in box. Includes Fuel Lid I purchased it and don't need it now. Never installed. Located in Muskoka, Ontario, Canada (P1P1R3) $300 no taxes

A question I cant answer. A John Deere 755 with 3 cyl diesel what should the compression be on a new motor.

Saw this on Youtube today. Apparently it happened about 3 days prior to me posting it. He was fortunate, no injury and the tractor seems to be ok.

My john deere 8520 will engage the starter when you turn the high beam lights on even if the ignition is turned off ,we have stipped almost everything in the cab and behind cab at modules looking for broke, burnt or wires touching cant find anything been at it for almost 2 weeks , dealership...

I have a 2005 6320 that 3 years ago started fine in the barn at 40 degF. We were putting out hay with the temperature in the 20's and, after a few minutes at idle the tractor would not throttle up and the "Additional Indicator Light" (square red light on lower left console panel) was flashing...

We have a John Deere 4052R HST and even when we use it to blow the parking lot off in B range for half hour first, and then go down the road after in C range, it will not go over 10-13 mph and after 3 miles it will creep up to 18.5 or so mph after going down a hill a bit. We leave it pluged in...

I have a 410 loader S/N 006943 with the AH 163577 hyd cylinders. I can't find the S/N lookup for the loader but understand there are different kits based on that. Could somebody point me to the S/N lookup or tell me is the AH 176343 rebuild kit is correct for my cylinders? Thanks, Ken Pace, FL

I've been having some issues lately but now I can't get the tractor to start at all. The lights on the dash will come on but when I go to turn the key there's nothing. I recently tried to let the water off of water separator and feel like something I had done then is causing me this issue. Any...

Deere loses appeal in patent case against AGCO and Precision Planting By AGDAILY Reporters Published: January 27, 2025 https://www.agdaily.com/technology/deere-loses-appeal-in-patent-case-against-agco-precision-planting

I'm familiar with both setups and have to say I like the JDQA hook and pin style over the Kubota skid steer style. The Kubota seems overly complicated and stories of attachments popping off and having to adjust the pins and spring tension adding washers etc seem over complicated. The JD hook n...

need help troubleshooting yanmar 4ntv88 in a 2006 deere 110 tlb. so far new head gasket, radiator, waterpump, thermistat, cap,hoses, injectors, flushed a couple of times. engine stars and runs smoothly very little smoke. test shows no exhaust gas in coolant and there is no coolant in the oil...

Anyone know anything about the 2025 John Deere Pickup Truck? TIA Yooper Dave

Somewhat related to YANMAR as the Deere machines still use the Yanmar engines or kit tractors sent to the Deere assembly lines. From one of the largest online web publishers of Ag news, www.agdaily.com subscribe today and keep up-to-date . . . For big farms and small homesteads, there is...

We have a john Deere 6415 tractor. It drops the rpm's and doesn't go back up. When you crank it and take the battery cable off it will kill the tractor. We leave the battery cable off for 30 seconds or so. Then put it back on and crank the tractor back up. It will run fine for a few minutes and...

Good morning, I have a 2019 5115M that is throwing ccu 3033.02 code. Light comes on when I press the brakes and speedometer is almost always reading 0 - sometimes it gives the proper reading for a little while. According to jd docs it is " Trouble Code 3033.02 OIC Left brake pedal fault...

Hi, I know a similar question has been asked.... However, my tractor is older so I'm inquiring. I have a John Deere 3020 w an original JD Loader attached. My bucket is shot.... I happen to have a skidsteer bucket in excellent shape so I'm looking to purchase an adapter. I don't know what the...

Happy New Year everyone. My John Deere 5320 parking pau is no longer working and I was thinking about older tractors and how we used to always use the foot brakes to secure tractors when we parked them. I’m thinking if there would be a way to do that with my JD 5320. The brakes work fine on the...

Will a la 130 transmission fit in a la167 John Deere tractor

A new head gasket leaked on my John Deere 750. Compression gases were coming into the cooling system after about 5 hours of use. I bought a new head gasket from the John Deere dealer. What is the advisability of using head gasket sealer before installing it? If so what product would you...

Is there a good video on how to change out the steering cylinder on my 425? I looked on you tube and couldn't find much. Or maybe some one can explain it to me simply?

My 2010 model JD3320 showing Error 06. I’m certain there’s either a bad connection on the Hall Effect Sensor I think part #LVA17409 If I could locate this on the transmission I feel I could solve the error code by reconnecting or replacing. Just can’t locate it??? Please any help would be...

Just looking for a reliable source. There are numerous sources on the internet but they all want all my information. I just want to buy a service manual.

I just picked up a John Deere LX280 for my sister. It is -2F so I couldn't look for long, but how do you remove the air filter cover?

Hi everyone. I currently own a 1957 Ferguson F40 and it's an awesome machine. It's all I have for moving snow and of course it's limited in that it doesn't have 4 wheel drive or a loader. I'm looking for a compact tractor with 4x4, HST, and a loader. It will be used for the typical hobby farm...

I received a free series 51 spreader. The previous owner said that it "ran when parked", but the wood is bad enough that I don't want to try it until I replace some of it. I'm not restoring it for show. I need to use it. Are there kits? Patterns? Is it all 1"? Preferred material? Hard wood...

14' MOLDBOARD . AIR CONDITIONER . AIR SUSPENSION SEAT . AM FM CD RADIO . ANTI-THEFT SYSTEM . AUTO DIFFERENTIAL LOCK . AUTO SHIFT . BLADE EXTENSION . DIFFERENTIAL LOCK . EROPS . FRONT HITCH/LIFT . LIGHTING . MIRRORS . THROTTLE LOCK . TRANSMISSION GUARD . VARIABLE HORSEPOWER. Serial...

Does anyone have the instruction paperwork for how to program instrument cluster part #RE232258? It shows you how to use wiring harness part #LVB24863 to tell the cluster if the engine is 3 or 4 cylinder. It involves several steps like turning the turn signal "x" number of times. My fuel, temp...

My old gal has the shakes, and her mounts are shot. I see the replacement parts in the catalog, which don't look too hard to deal with, but I have questions about how to replace them. Online I have seen references saying it's a trivial job, but my local tractor guy seems to think its a bit of a...

John Deere 5075 maybe 425 hours broke down in the field on Saturday. Display said NEUTRAL. Transmission disengaged. Walked back to barn. Any ideas ?

Can anyone shed some light on what the hyd control under the seat is for on a John Deer 850? It is the one with a rollpin in a shaft, looks to adj flow or???

Injector Adapter for Compression Test on John Deere 750 Please does anyone know what size Injector Adapter I need for my John Deere 750 with a Yanmar 3T80UJ diesel engine? I was about to buy this kit but It looks like it will not fit. Is there a better kit that you would recommend...

Greetings all, When cold my injected x485 doesn't like to start well. I turn the key to the on position and let the fuel pump prime up and stop and then turn the engine over a few times and repeat this 6 or 7 times before I try to start it for real. This is all that I have found that helps. Has...

I have decided on a 5e series tractor with a loader. I have a price from my local dealer for a 5065e 12 speed power reverser MFWD 520M loader price is 43K looks inline with what I see on machine finder. Does anyone know what kind of discount I should be able to get from thier first price?

How can I find out the year that this tractor was built? I don't have access to the VIN right now, but have the Product ID, and engine serial number... Any help would be great!

My brother bought a JD 4200 a few months ago previous owner ruined the injector pump and didn’t time it before removing pump. Since then we’ve removed the front cover to line up all the marks on gears no my question is how do I go about timing the pump. Since this photo the lines were matched up...

I had read that JD was building in Mexico. Now they are building in the US. I wonder why?

Always serviced properly. 4 wheel steering 1177 hours Threw a belt or broke belt, had it serviced while being repaired. Belt replaced. Used it 2 hours, broke belt again, replaced 2nd belt with instructions to check blade spindles. used it 2 more hours, broke belt again. Independent repair...

I'm getting ready to flush and clean the cooling system on my John Deere 6400 tractor. The operations manual states that I should drain the system and fill with a "commercial cooling system cleaning solution". Run until hot, then drain cleaning solution. Any recommendations on what product I...

Looking for a 110 TLB for the following reasons: I like that it's a TLB, I like the ability to use skid steer attachments, and retain 3pt hitch / PTO for implements. What other brands/models should I be looking for? I don't want to just slap a backhoe on a farm tractor. Thanks! O.

It is hard to find details on exactly what kind of coolant this is and what aftermarket alternatives it can be replaced with. I got a decent amount of Motorcraft ethylene glycol P-OAT type coolant left over that I'd like to use if I can. I think I could use this if I drain whatever is in there...

The front bell crank in the brake linkage can fail causing the tractor to lose braking, resulting in a crash hazard. John Deere Recalls Compact Utility Tractors Due to Crash Hazard

Has anyone seen this about John Deere Trump gave them a warning willy

I just noticed I can no longer find the parts diagrams for my 757 ZTrak mower at partscatalog.deere.com. They only have parts diagrams and lists for the "Worldwide edition" of the mower now, whereas there used to be three (maybe four?) versions listed, with a split by serial number. The...

My 445 has always ran hotter than I'd like but whenever the gauge got up to the red the thermostat would seemingly open up because the gauge would drop back to around halfway and start climbing again. The last time I had it out I noticed the center light started blinking. Its one long followed...

Got a 1971 (I think) 820 3 cylinder. Its been running ok but the the fuel filters were extremely dirty so I replaced them. It ran good for a couple of weeks then started missing. I found the return check valve had some trash so I cleaned that out and it ran ok for a while. It started missing and...

I've got this Gator. Belonged to wife's cousin next door so I know most of its history. There doesn't seem to be ANY tag on it with a serial number so I'm blind to that question. Embossed under the passenger seat is what appears to be: W00? (B or 8 or maybe P) X4X073915 Long story...

For sale is a brand new John Deere StarFire 7000 receiver (SF7000) with SF1 signal, manufactured in 2023. This cutting-edge satellite receiver unit is designed specifically for John Deere machines, providing enhanced accuracy and stability for all your agricultural needs. Installation Note: A...

Where is the Neutral safety switch located on a John Deere Model 2305. I can't seem to locate it

My Rear hydraulics won't go up and down. the level to operate the hydralics won't move, this all started when I tried swapping hoses to find out why my front loader wound tilt, It goes up and down fine but will not tilt. any help appreciated.

Tractor S# CH 0850 S023370, has p/s, backhoe, front end loader with float. You guys helped me put p/s on this tractor in 2020, I hope you folks can help me with the SCV valve. The SCV on my tractor is made by Dukes Fluid Power, #1627 AN, JD original part #RE 19910, revised # AM 107083. With...

I have starting issue just did over haul has new starter new battery but still won't start thinking it's electrical but can't seem to find all my grounds and thought maybe a diagnostic schematic would help also notice on left side of engine theirs seems to be fuel dripping seem like from a bolt

Hi there I am new to the forum I have a problem with my tractor, I hope someone can lead me into the right direction for what I should check to figure this out. I was out in the bush with a rotary cutter. At some point when backing up Al of the sudden the tractor just turned off and that was it...

I have owned a few brands and Deere is a nightmare. Purchased a new x570 18 months ago and was told commercial users got priority for service. My mower has been in shop three times since purchased. Twice for steering problems. I followed up after three days and parts were not ordered. I...

Hi, help. A friend of mine owns this Gator, uses it on the farm for chores. Last week on a run to the burn pile after she turned this off it would not restart. Thinking it ran out of gas she filled the tank making no difference. It had not run out of gas. I looked at it today checking the...

Trying to help a neighbor in his late 80,s with his tractor that he has had for a number of years with no cranking issues, It was running fine, he shut it off and when he later went to restart it, it would not turn the engine over, you can hear the starter spin. It is a 12 volt battery (guessing...

I am having electrical issues with my 850. Purchase it and the wiring is all cut and spliced. Would like to put it back to some what original. If anyone has a diagram it would help me so much. Thanks Don

Take a look at John Deere Layoffs Spark Creative Corn-Pocalypse - Farmer & Cowboy Even if you don't like the ideas, you have to admire the cartoon art.

hey guys. I have a John Deere 2020 from 1970 and I have a problem that I can't solve, the brakes are very hard, I have to apply a lot of force to brake and suddenly when I apply force they brake suddenly. In other words, they do not brake progressively. I've already cleaned the brake pedal...

Hi, I have the jd 6410 engine rebuild and the engine loom has some issues as the tractor does not start. Before it was starting OK, now the dash bord is lit up and when I tried to start the engine will switched off, i did replace the loom cabin plug L102313 {no. 9 in the photo} as the previous...

I saw this posted on Facebook Marketplace today. Of course its a Can Am not a John Deere, but I was thinking that if John Deere had actually produced a side by side UTV like this with their dealer network that would have moved very close to the top in sales. The Can Am Defender is a very...

Good afternoon, I was using my 1970s john deere 301 with a post hole digger and after a few holes, when I went to disengage the PTO, the lever is stuck engaged and won't budge. Pressing in the clutch disengaged the pto, but I can not get the lever to disengage. I have tried to disengage...

Hi folks, I haven't posted on here in FOREVER, but I came across a local John Deere 650 that is being sold for parts. Obviously it doesn't run and it is in pretty rough shape. The seller says the motor is locked up from sitting outside with the exhaust open and getting rained on. I think these...

Jd4310 having trouble cranking. Has anyone had trouble with fuel shut off valve stuck in off position. With the fuel solenoid removed . Putting my finger in solenoid hole the valve has no movement.

Last year my dad purchased a brand new John Deere 5060E open cab with a loader. My first look at it I couldn't help but think: "that tractor has a high center of gravity." Part of the reason he purchased it was the high lift rating of the very heavy duty bucket. Without fluid in the tires it...

Hey guys This machine turning Into a damn nightmare. I had a bunch of oil leaks last fall. Had my mechanic check and repair them. Most of them were hose fittings, and some seals on the pumps. After about 50 hours, I had another leaks from the pump. My mechanic resolved it. But since then, the...

I bought this 1987 430 which has under 800 hours, to eventually replace the 1976 JD 300 we have been using for over 30 years for all-around hauling of small stuff and mowing of rough areas, where I don't want to take my Kubota F mower and tractor with flail mower & loader would not easily fit...

I have a very basic question for everyone. I just started my tractor and it had the 'engine status' light and the stop light on so I turned it off immediately and checked the oil. I was not raised on a farm and I just bought it. I think I'm correct when I say that you add the oil where the...

Was mowing for about 15 min, had to stop to mower to move some limbs. I had turned it off. Went to turn the key, and starter does not engage. The digital display looks fine. I made sure brake was on, handles out, and blad turned off and still no turning over. I had driven though some wet...

I have a 1987 John Deere 950 with front end loader that I am looking to replace all the hydraulic hoses due to age. I have searched online quite a bit and I have not had luck finding the answers I need. Were these hoses standard lengths, and fittings that I can just order from somewhere or will...

My John Deere 990 Compact tractor has a problem. It won't start. I was using it, stopped to do something and tried to start it again and nothing. The tractor made a small click but nothing else. I have a new battery in it. Cleaned the terminals, put in a new starter and ignition switch...

I recently purchased a 3046R that came with R1 Ag tires. Been using it in the yard doing some landscaping, and obviously tearing up the grass quite bad. I also plan to do a ton of work in the woods, and I'm worried about the R1 tires sidewall not standup up to the sharp cutoff brush stub...

Hello I'm new here I'm currently working on replacing the seals and bearings on the front axle of a John Deere 6220 SE and I can't find the torque specifications for the ring gear bolts. I've looked through several online resources but haven't been able to find the exact specs. If anyone has...

https://news.yahoo.com/news/finance/news/john-deere-announces-mass-layoffs-172937300.html

Howdy, was planning to juice up my AC with a can of 134a but seems JD's low side port is not a standard size. It's bigger than the quick connect on the hose. Did I just not press hard enough or is there a JD specific size for recharging the AC system.

I'm looking to purchase a 2003 JD 5205 4WD with 522 front loader with 4 in 1 bucket. One owner, (friend of mine..I know the tractor), 1500 hours, like new condition. No Cab or canopy. Only ROPS Any guesses as to what it is worth? I haven't had any luck finding any comparables on any of the...

I have the above mower and the trans/axle crapped on me; looking for a replacement of this 30yr old piece, but don't where to look. STX 30 and STX 38 utilize the same Peerless unit. Before you tell me to junk it, the rest of the mower is still in excellent shape and I'm 82 years old so not going...

I need help figuring out what to buy! Please tell me what YOU would do! And how YOU would approach this project. We just bought a 150 acre farm (all crop land). All of it is rolling hills - nothing terribly steep, but not flat either. In the next year or so, I need to: 1. Cut and grade an...

Was wondering what percentage everybody was getting off on John Deere 5000 M series tractors.

I am struggling to find a new or gently used surface wrap (net wrap) top roller. Mine has a small gash in it and was looking to replace it. I have called many aftermarket places with no success and John Deere wants over $5200 for the roller assembly. My baler is only worth $4000.... the JD Part...

My 5320 solenoid won't engage or spin the starter, I started to start it the solenoid engaged I let off it and thought I smelled a small burning smell then went to engage the starter only a very weak clicking then nothing, the positive post on the starter tests almost 14 volts, when I turn the...

Recently picked up a JD 5205. Noticed the top link didn't seem to work as it should and found one end turning, but not going in or out. I am using another one for now, but would like to repair the original part if possible. Have looked quite a bit and do not find any good info on taking these...

Greetings......I have a John Deere 345 lawn tractor w/Kawasaki FD611V 20hp engine.... Engine just clicks when trying to start (will finally start)....ongoing problem for over a year....finally decided to replace the starter solenoid today. I got everything all put back together only to...

A friend of mine has a 6130D Deere and he mows roads. The transmission looses prime when mowing and the tractor gets on a left handed slope. After a few minutes off and in neutral it will go again. Will mow all day with the right side down hill. Deere dealer won’t even look at it so he...

My old gator I believe 90s. Model need to clutch but I can find no identification numbers. Tags are all gone. Can you help me identify this? So I can get a clutch.

I attempted to plant sunflowers. I am afraid I planted them too deep. My 246 operator's manual said not to use the tractor hydraulics to control depth. I ran the depth control screw all the way out. I am looking for suggestions to keep the seed depth at around 1/2 inch. I don't think I can...

I have a 405xxx serial number JD 2040. she was running fine. well she had a leaking Injector pump which we rebuilt/sealed. I also dropped the loader down a bit to help reach the starter which I replaced at the time. Tractor running great now no more loss of power from leaking IP. Start it up...

The Deere 5105 I bought with a piece of property is overheating. The only sign is the gauge, which when I work the tractor heads into the red within 5 minutes or so. It's not steaming out the radiator overflow. There's no oil in the coolant or coolant in the oil. I replaced the thermostat but...

Starts up and runs beautifully for about 15 to 30 minutes, then it begins to stumble and effectively stalls. Give it a few minutes to cool down (is not running hot) and it will start up and run. Since it is already at operating temperature, it takes less time for it stumble and stall again...

I have a GX345 John Deere with a Kawaski FD611 engine water cooled 20 HP. I have no serial number on this mower. According to John Deere the correct PTO Clutch for this unit is pn Am133209 or Am131779 The Am 133209 will not go around the crankshaft and the Am 131779 is way to big and the key...

The throttle has been getting stuck at idle. Not sure exactly how the governor functions in relation to the linkage but for a while I couldn’t throttle up from the handle but if you moved the linkage at the injection pump it would be fine for a few days and then it would get stuck again. The...

Hello readers, I am at a dead end. With warm weather finally at the house. I decided to swap engines from the 4100 gear driven ( rear end went out ) and the 4100 HST ( Middle piston went after a loaner used ether on it.) Simple enough swap. Both engines would crank and run. A few days ago I...

Up for sale is John Deere Autosteer System: Greenstar 2600 display with Autotrac and Swath Control Pro activations, Starfire 3000 receiver with SF1, and ATU 300 Pm me if you have any questions.

New to me 2004 5320 and I have 2 questions I'm hoping someone can answer. The Manual talks about an early and late model 5320. Does someone know what years constitute an Early model or what Serial Numbers? Question 2: My brake lights aren't working, I don't see a separate fuse for the brake...

Hi, I have an old JD 1020. Which now days I sudenly had quite big brake and I pushed in the second speed (Hi), starting that moment - the gaerbox os blocking frequently, is hard to change the speeds, one of the speeds mainly the second one - is not working well. Its seems to me if the switch...

I have a john deere 430 lawn tractor and I am wondering if an aftermarket fuel pump can be used to replace the inline pump, has anyone used a different pump with success and if so what pump was used. Thanks a lot, just repainted, installed new tires, gave her an oil, air & fuel filter and she...

Hey all, new around here. I have done everything I know how to do so far and have now turned to the interwebs for help. I have a JD 3005 compact utility tractor that won't start and I don't want to blindly throw parts at it. I was running it just fine and turned it off to talk to someone and now...

i have a john deere 345 that has been sitting for about 7 years after my father in law passed away. I brought it down to my house and got it running perfect but I can not get the pto to engage and have no power to the pto. This thing is driving me crazy lol . Bought a new pto switch nothing and...

Hello, while changing the battery on my F525, I accidentally dropped the handle of my socket wrench while it was attached to the ground and of course it fell on my hot terminal and started sparking (this was on my new battery). It took me a few seconds to grab a piece wood and knock it off...

Started up my JD 5055e drove it up to my shop to remove the 3ph to install the backhoe. Shut it off, removed the 3ph equipment and went to restart it. Nothing! I know about the cold start sensor at the front of the engine and that's been unplugged for years now. Thought the battery might be low...

2015 john deere 5085m keeps throwing code ECU 3673.07. It worked fine last fall, it’s been sitting pretty much all winter. Thanks in advance

John Deere 4300- I have this fluid leak in my left front tire area and was wondering what and where the fluid is coming from and how I can repair it. I am just guessing it is a seal gone bad in the front axle. Any thoughts will be appreciated. Posting a few photos to highlight the problem,

I'm going to a larger deck on my 3320 and want to sell the 60 deck. Auto connect. Will drive a ways to meet for a serious buyer. Located in Charlottesville VA should also fit the newer 3R tractors.

I'm looking for a smaller tractor to do some grading and fencing (post holes) on my small residential property. I already have a mower, so cutting grass will not be on the list of this tractor's chores. I have a limited budget (less than 10K). I found this at a dealer about an hour away...

I have a hose on my loader that just started leaking, so I figure it's time to change out all the hoses. Are the cheaper (Ebay, China) hoses working for people? If not, what's a good resource for procuring pre-assembled hoses?

I was mowing with my D140 and on my way up the hill I got the deck stuck. I smelled burnt rubber and all the sudden it wouldn’t move. I assumed the belt slipped so I replaced it, however it still won’t move. It will move a little if I push it while my wife pushes the pedal, but then it stops...

The tractor will only go 14 mph in high rang and when I try to use the cruise control I get a 5 error code on dash

I have an opportunity to buy a used 2012 John Deere 4005 4x4 tractor with a 300CX loader with 320 hours on it for $20K. It is the same or similar to a 990. It has 42 hp engine and 35 hp at the PTO. It is a 9x3 manual transmission (synchronized between first, second, and 3rd forward gears, NOT...

Battery will not charge. No blown fuses K - 5 relay replaced along with voltage regulator. Alternator or generator has 32 volts AC output. Yellow battery light comes on. I have a new voltage regulator in it. Checked the white wire output was 14 volts! Great right? Ran the tractor for about 5...

Anybody looking for a MX10 in the SouthEast ? It’s listed over in the marketplace. North Georgia Cutter is SOLD

I bought this 3pt hitch lift type MX10 cutter brand new. Used very little. Low hours. Approximately 2200lbs going off memory ? Works great. Always kept inside out of sun & weather. I went up to batwing & zero mower. $8900 pick up in North Georgia No trades Call Mike six78 98six...

Good evening everyone, new guy here. I recently bought a JD 2350 with a 245 loader. It has a quick-attach bucket, but not like the hook and pin QA I am used to. Mine has two square vertical spring loaded pins that lock the bucket in place. Attachments for this style seem pretty hard to find, and...

A 2016 John Deere 1025R with Powerflow Material Collection System! $15,000 less than new! At 247 hours, this 1025R is powered by the 23.8hp Yanmar 3TNV80 diesel, 3-cylinder, liquid-cooled engine with a 2-range hydrostatic transmission. Equipped with the 120R loader and JDQA bucket, and the 60″...

I recently purchased an 850 with factory dual remotes. I'm a large person and the levers hit my leg. Additionally, both valve bodies are leaking. I want to delete the remotes completely. I only run a mower and have other machines with loader. I've found the replacement "cap" that has no ports...

I am trying to determine the proper rear ballast for my 5055E. I have a 520M loader that has a max lift of over 3k lbs. I want to lift at least a ton and trying to determine rear ballast. The manual for the loader shows two options for a cab tractor and one option for OOS. I have an OOS. The...

Here is a PDF for how I did it. I hope it helps you.

I was stationed overseas for 4 years, meanwhile a handy man hired to maintain my property back in the states, blew the engine in my JD 4610. When I returned home I found it completely disassembled and I'm trying to put it all back together. There are a few points I'm stuck on, as I can't...

Started well run like crazy than died tried restarting with a little gas in the air breather started well than tried a little diesel in the air breather and bum an explosion what damage could it have caused .

Stated it and it run like crazy for 3 min than died

Hi, just joined and first post. I have a 25 acre property, some steep slopes and mostly forested. I'm wanting to buy a new smallish tractor with 4 in 1 bucket to do the following: Moving rocks and soil Pulling cut down trees out for firewood and lifting them into stacks Grading/maintaining...

Good running John Deere 70 Tractor with wide front end. No hour meter, so hours are unknown I have video of it running, if interested

Ive been reading here and on the internet that some owners turn up their hydraulic pressure on their 2520s been thinking about doing that any of you owners had done this? I check mine and its 2475psi thinking about going to 2700 will I break something or blow seals out with 200 more psi thanks

Does anybody know how much a complete set of 19.5-24 & 12.5/80-18 New R4 tires & wheels would cost from JD ?

I'm looking for comments and thoughts for the John Deere Frontier RB2284 Rear Blade. I have a 72" Land Pride and I'm thinking of going to a wider and heavier blade. This is much heavier than my current blade and I don't have rear hydraulics. Is this too heavy to adjust without hydraulics? My...

Anyone have any idea when this was built and what it is worth? I know in most case with serial numbers 001 would be the first one built? The story is it was bought new with this 1953 John Deere 40.

Will a 120E or a 120R fit on my 4010 Compact Utility Tractor?

Hello Everyone - Friend has a 955 and is looking to purchase a front broom / sweeper. He has a front blower with tractor quick attach - yet to put on but has the complete set up from what I can tell. From what I understand, the 246 broom was the model for the 955 (55 series tractor). I...

My 1445 has 1725 hrs and the deck will not stay float . It has a danfoss hydraulic control valve . I am not sure if or how to adjust the detent to keep the deck in float

Back story on tractor is I did a rebuild on it new pistons, rings, rod bearings and head gasket. Flushed radiator new thermostat adjusted valves. I got it back together and it will start but it just seems like it has no power and I’m pretty sure it’s getting to hot also it won’t idle has to be...

Two questions: I have a commercial-grade JD Zero Turn mower that I use to mow my rural property. It was purchased in 2012 and has 870hrs on the clock. It is serviced regularly and is in excellent shape. The dealer says that it is time to replace it because JD is discounting the 2023 models, and...

I have a 1986 John Deere 650 tractor. it is currently stuck in 4x4, the shifting handle just free wheels like its not hooked to anything. the roll pin in the handle is good. Can I pull the shaft that the handle is mounted on? I am assuming that the shaft it broken or what ever it was driving...

The tractor has been sitting all winter, and now it won't turn over. The solenoid gives a loud clunk, but that is all I get. No hint of a starter problem before this. The battery is good at 12.7V at the starter. Tried shorting across the posts on the starter, and got nothing, so I'm thinking the...

Need some help in figuring out why my front loader will work, however not at strongly and will lower without contant monitoring, while 3 point will not go up or down....changed filter, not leaking hydralic fluid....any suggestions? Thank you, JMS

Hello All, I have recently bought a 1966 John Deere 4020, got a screaming deal on it. I am hoping to find a loader for it. I have seen that John Deere Loaders 48/148/158 do fit and work. I was able to find a few 'fairly local' but the asking price is higher than I paid for the tractor. I am...

I started a rebuild on my little 850(yanmar 2500). Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the...

I started a rebuild on my little 850. Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the middle cylinder...

Bought a 301A over a year ago that had been setting along time turns out all I needed to get it started was a new fuel transfer pump and rebuild the starter ….... everything seemed to work well except the rear lift arms wouldn't hold a middle position no biggie ran for a bit but I noticed was...

Quite simple to replace the seals.

Probably not the most apples to apples comparison but I have been looking at new tractors for a couple of years now and getting closer to pulling that trigger. I have looked at and drove most fo the current brands out there. LS was far from my list of tractors when this started. However, there...

I just recently bought a John Deere 850 for a super cheap price compared to what the market is in my area. Everything seems to work as it should and it seems pretty clean. The only issue I’m having with it is it seems to have a slight miss to it around 2,000rpm not sure what it could be I’m...

I purchased a 5520, the instrument cluster is not working. I sent it to be tested and it works fine. I've had a mechanic work on it extensively with no success. The cluster has rpm, fuel gauge and temperature gauge. I'm considering just adding aftermarket fuel and temperature gauges. I'd love...

Hello My frontier RC2060 brush cutter has started to feel a little odd, .. more than usual vibration and noise during operation and a tendency to sometimes shave dirt even when the cutter is not at the lowest position . On inspecting the cutter, 1. I can see a thin film of oil on the underside...

I know there are a couple other threads on this, but wanted to help contribute: - Proof of Concept - LED POC Test Video Quick video showing reflector cutout and LED Fitting. Reflector Cutout Fitting LED and Controller Test Confirm, then order second set of LEDs There was a logical cut...

Having an issue with my 6410. The problem began with the reverser not working correctly, it would only go into reverse and when I put it to forward it also would beep and go in reverse. I shut it down and now nothing happens when I turn the key to start it. It appears that it thinks it's not...

so she cranks but wont fire! I found she isn't getting fuel because after some testing without luck I finally decided to put gasoline on a rag and cover the intake with it and she fired right up. This tells me it is getting everything but fuel. I noticed I wasn't hearing the click as usual from...

I’m wondering if I can some initial thoughts on what might be wrong with our Deere 110TLB engine. Engine has about 1500 hrs. on it - it has always sounded terrible but never had a performance problem. I was going up a steep hill when it suddenly lost power and it conked out. When I tried to...

Information to post and pass on. John Deere Deluxe SCV Coupler updates John Deere Hydraulic Quick Coupler Socket Replace in pairs Deluxe SCV valves new coupler design 2 x John Deere Hydraulic Quick Coupler Socket - AL221083 2 x John Deere Clip - L158630 2 x John Deere Hydraulic Coupler Sleeve...