kubota b2620

I recently purchased a 51R battery as a replacement for OEM battery on a Kubota B2620 tractor. Turns out the 51R is 1/2 inch bigger in depth and will not fit without major mods. Has anyone replaced their battery in a B2620 that can point me to the correct replacement? Thanks

I have a Kubota B2620 with LA364 Loader on it. Sometimes when I do to tip the bucket of the loader up/down the control lever seems to stick, if I move the lever a little left/right then it works. Is there some part that I need to replace that would fix this problem ?

have a b2620 and plan on putting a quick attach on the loader. Was wondering if the Kubota B2673 plow 72 in quick attach (pictured)would be OK to mount on the LA364 loader on a B2620 tractor??

I have had a B2620 for 12+ years. 800 hours and love it. I use it to move dirt, brush and snow mostly. Some grading and gravel road work. 7 acres mostly level with field/grass and about 3 acres of wooded area. Looking for more power to move snow, dirt and gravel and a grapple to deal with...

Hello All; This YINTATECH Skid Steer Quick Tach Conversion Adapter Bobtach Latch Box Weld On QTK, I am thinking of adding a quick attach to my tractor but don't know if this one is any good or reliable. Any information helps. Thanks

Worked on a friends B2620 that would not start. Turned out the rod that pushes the HST treadle safety switch had popped out of the hole in the metal cam plate behind the wall of the case. That is one b@#$%h of a thing to get at.... This picture was taken after I forced it back into place...

Thinking of buying a finish mower for my B2620 for our 2 acre lawn. I really would want to go with a 6' cut, but with 19 PTO HP, I am just below the recommendations for a 6 mower. Is anyone using this combination? My lawn is mostly flat and I keep it cut fairly short. Thanks, Tim

I know it's outdated, but didn't want to get rid of my B2620. So now that I have the 3 point arms all off to get it set up for the new backhoe I just bought for it I was wondering......am I remembering correctly that there was another B series that had extendable lower arms for the 3 point...

Only 370 hrs on a five yr old B2620 that has been maintained and babied and absolutely never overheated. I open the oil drain plug and get about a shot glass worth of coolant after a good sit. Must be really slight because I haven't had to add coolant to radiator or overflow. Called Kubota and...

The joysticks on the BH65 have a set of valves underneath them.... Could I take off the endcap, put another valve there, use longer bolts, bolt the endcap back on and use the new valve as a 3rd function?

I had this posted on a Kubota forum, but now that we have a project thread here I'll post it up here too so people can see what can be done with a small tractor. I'll start with this......some of the one kilometre of bush road I made on my property for harvesting my firewood from up in the back...

Hello TBN- Can anybody tell me what size dust plugs and caps I need to replace the broken ones on my B-series hydraulic hoses? More specifically the ones that connect to the front snowblower and quick hitch subframe. Thanks much!

When i pull back on the stick to raise the loader, it goes up real slow. Now when i pull back slightly on the stick it goes up normal. I've switched the quick disconnects and its still only the direction of raising the loader. Fluid is up. Any ideas? I've messed with the 3pt hitch lever, pto...

When i pull back on the stick to raise the loader, it goes up real slow. Now when i pull back slightly on the stick it goes up normal. I've switched the quick disconnects and its still only the direction of raising the loader. Fluid is up. Any ideas? I've messed with the 3pt hitch lever, pto...

I have a 2013 B2620 with 180 hours on it. Just recently I am noticing a feed back almost hesitation through the steering wheel. I turn the wheel and the steering wheel fights back and tries to turn the opposite way to the way I am turning. It almost feels as though there is air in the system. A...

I have narrowed down my search for a tractor to Kubota based on my needs and wants. I want a small B series and was considering a new B2601. I have come across a used 2008 B2620 with Loader, backhoe and mid mount mower deck for $21,300 with 483 hours on it. I think if maintenance was done on...

On my B2620, you press down on the brake pedal and then push down on the orange handle by your right knee. Then you can lift your foot from the brake and it stays locked. My beautiful wife was using my tractor while I was out of town. My scaffolding showed up and the driveway was too muddy...

I'm trying to disassemble the loader valve on my circa 2012 Kubota B2620 (see below for why). The attached picture shows my current state (I've also disconnected the top of the bucket control spool from the linkage). At this point, I don't know how to get the spool out. It's possible that the...

Yesterday I was using my tractor to knock down weeds in my back yard weed patch. After about 2 hours, I was headed back to it's parking spot in my garage. I had to dismount to open the gates, so I reduced the engine speed to idle. As soon as I got off the tractor, the engine died. Now it won't...

Good morning... Yesterday I received from my Kubota dealer a quote of $7300 for a brand new BH65 backhoe, 12" bucket, all inclusive and dealer installed. My counter to that was $7000 and they perform a full HST/hydraulic fluid change including whatever filters are necessary and an oil change...

is this a quick/clean bolt up? anyone tried it? please with results? I sat on a 2601 recently...seat was impressive by comparison.

Any comments/experience with this Tractor 3 Point #3F Bale Spear, Hay Spear, Hay Mover on a Kubota B2620 series. I use round bales, approximately 800 pounds. This could make my life a LOT easier, if it is as advertised. Thanks Fred Cain #3F hay mover is for a standard category 1, 3...

My primary dislike of my B2620 is the fact that it's impossible to get truly smooth loader control due to the linkage that connects the joystick to the actual loader valves. I've lubricated the linkage with seemingly every lubricant known to mankind, but the action always remains slightly...

The cutting height knob id very difficult to turn. How do I fix. Thanks

From doing my searching here and on the internet at large it appears that the only two ways of getting quick attach pallet forks and I broke them out into pro's/con's below. Can you all confirm if I am correct? Maybe something new has come out recently? My main goal is to get pallet forks that...

So my loader valve on my 2012 B2620 had a failure. The little check valve broke off & fell down into the curl spool & it's pretty messed up. So I took the valve to dealer to see if they can do anything for me. If they can't & I have to buy a replacement valve for my tractor I was wondering if...

Greetings folks... So I found these suitcase weights on Craigslist for $350...Kubota front suitcase weights and would like to ask a couple questions: 1. Is the asking price reasonable? (I have no idea what these cost new) 2. Can the weights be mounted on my B2620 all the time, even with the...

I need to move the BH65. I know the "correct way" is to remove the 3pt hitch and install the Backhoe on the B2620. However, it is cold and I will need the hitch again before I need to use the BH. Is there a safe/practical way to lift and move the BH and with the FEL and chains? Just asking.

2014 B2620 with extras, FOR SALE Looking To sell my 14' Kubota B2620 tractor loader74 hrs looks like new, box blade, quick hitch, filled tires, 3rd function kit, (mytractortools)quick attach system, forks, and Hyd grapple. I'm looking to sell this wondering what I should ask? $18,000????I'm in...

The B2620 pretending to be a Cat again.

Yup, another one. I would like to build my own Top and Tilt setup plus one extra rear remote (3 total) for my Kubota B2620. I know Brian at Fit-Rite is the go to guy and I'm not knocking him but I'm hoping I can save some money by DIY. But DIY means getting help from anyone willing. So it won't...

2014 B2620 stalls out when warm; needs about 15 minutes to cool off before restarting. Dealer thinks it is a vapor lock, but has not been able to correct the issue. This is very frustrating - to be out working and quit every hour!!!!! Any input would be appreciated. :confused:

2014 Kubota B2620 w/only 200 hours, stalls out when hot. Dealer thinks it is a vapor lock, but can't seem to fix it. Very frustrating to out working and have to let it cool down after only an hour. Any input appreciated.

Hello everyone; I am following a suggestion for this post, I have a B2620 (2008) 4x4 HST and the other day after some light work I shut it down later came back would not start. I already changed the OPC controller for a new one, readjusted the forward/reverse switch and ensured the PTO was in...

May have been asked before but I was wondering if anyone has put a suspension seat on their B2620? If so what brand/model. When I mow the grass the OEM Kubota seat with springs under it beats the crap out of me. Hoping someone has changed one out. Thanks

Talked to my dealer the other day, replacing my b2620 with fel,bh, & mmm with a BX2670-1. Sold the property I used the B on, so going back to a lower profile BX. Added the quick connect bucket, fel, mmm, brush guard, and pallet forks to the BX. I know I will probably regret getting rid of...

I see a RC54-24B for sale locally and noticed it fits the older style B7500, etc. anyone know if it is possible to put this on my B2620

All I can say is this stuff is awesome, i abused it today and it never missed a beat! Fit and finish is top notch. I love the Precison of this smaller grapple, it handles brush piles and logs very well!

Anyone changed the HST oil on a Kubota B2620 lately? Coming up on 400 hours and the manual is not that clear. How many drain bolts and is there a screen to clean in there somewhere? Any info from somebody that has actually done it appreciated. I think mine is an '08 if that makes any difference.

Good Day! I have just about had it with my Cub Cadet LTX1146 and bercomac snowblower and have decided to get a real tractor. After considering New Holland, LS, Kioti and Kubota i have finally decided on Kubota (0% for 60 months and dealer is 15 minutes away, all of the other an hour away). I...

I'm a frequent viewer and very occasional poster, but I always value the collective wisdom available here. I've been pondering a step up from my current BX25 for some time, and now have my eye on a 2009 B2620 with FEL, BH and 60 inch MMM, with just under 150 hours on the meter. I haven't visited...

Hello does any one have the same problem when backing up a long way the pedal is so hard to push Ive gave may self a hernia I have to keep a bush road clear to get out every day except sundays has any one devised a hand operated lever Ive even looked at the return spring to...

I have a LA364 loader. The loader works like it should for up and down of the arms. But it won't dump. But it does curl up. The problem started after hitting something on the left side with the bucket in dump position while leveling some limestone. At first it would dump very slowly but curl...

Finally got a decent little 4wd tractor. 2008 B2620 with BH65 hoe, thumb and canopy. Here she is as she arrived with 196 hours: Already put to work making moving wood to the deck for the winter easier. Now, a few questions for you TBN'ers. Throttle resistance adjustment: The throttle...

I think this is common knowledge but I thought I would publish my experience anyway. I purchased a B2620 a couple years ago and I mow a lot. We now have 700 hours on the tractor. I am on my third mower position control assembly. Installed these assemblies run approximately $275. The B2620 has...

When I say B2650 blower, I don't mean it is from a B2650, I mean that is the model of the blower. Supposedly it fits the older B series machines like the B7500.

Before I take the plunge on a B2620 that has tickled my fancy, was hoping for a little more input from the collective knowledge base here before I dig myself into a hole. That's the final pun of this post. Snow: Living in New England, we regularly get snowfalls of 6-10" which I can handle...

I have sold my B2620 and still have the Work Shop Manual that I purchased from my Kubota dealer new for $80+. Seeing I no longer need this I figured I would offer it here for sale for $50 plus shipping in the lower 48 states only. Not sure if I can list this here, as I have sent several PM's...

I thought I would share some info on my recent grapple upgrade. First off, I have a Kubota B2620 w/ LA364 loader, BH65 backhoe and 54" mid mount that was bought new in April 2013. During the 50 hour service, I had a W.R. Long electic over hydraulic third function valve kit installed along with...

Any time I move PTO lever from 540 to neutral I get horrible grinding. Happens occasionally moving from 960 to neutral as well when mowing. Is there an adjustment somewhere? ANd yes clutch is depressed. When there is no load on PTO its not an issue... I am perplexed. No matter how gently I move...

B2620 owners, I'm looking for the total length from the bucket to the 3 pt hitch. Thanks in advanced.

I I have a 2620 - seem to me like the lift arm for the underbelly mower deck is bent. In the manual it looks almost 90 degrees, and bent upward by a few degrees...so when the lower link lifts on the lift arm, it forces the lower link outward. The rear bushing on the left lower link is...

So wanted to give my 2 cents on the ever popular bx vs. b debate on here and give you my personal experiences. I started with a BX 2230 loader/mower and loved it. Sold it because I got a great deal on a zero turn (Kubota zg223) and already had a b7800 for loader work. Well the zero turn was not...

Might sell some property that I used the b2620 on (fel, bh, mmm), looking at going back to a BX model. Has anyone used the BX2670? I have a ZD326 to mow grass with, but it is nice to have something to pick up stuff for me. If I sell the property I won't need a backhoe taking up space in...

Couple pics of the first phase of repairing my bushroad washouts. Very impressed with the little B. Tires aren't loaded and it pulls a loaded 60" box blade full of loamy sand up the hill no problem at 2000 RPM. I thought for sure I was going to have to bring the bulldozer home, didn't think the...

I'm sure JOHNTHOMAS will chime in here... Sold the BX the other day, so I'm going for the B. My last concern is the tires. My last B's sliced the sod on turns, albeit sharper turns. I test drove one last week with the turfs. It also cut. I'm only concerned in areas of the same pattern...

I just sold my relatively new BX25...which was great. But I have always had my heart set on a B2920. However, it is my understanding Kubota isn't going to make them anymore??? Why? Anyway, now I am contemplating the B2620 or the B2650? There seems to be a pretty considerable price...

Didn't make the trade. Keeping B2620 FEL BH with 39 hours till someone gives me $19,250 for it. Reason for the $750 discount is because of the Kubota discount coupon I rec'd which I can use so passing the savings along. Did trade my B7100 1090 hours 4wd HST to Barlows. BH thumb and new 16' dual...

Would anyone know the MFD axle capacity for a B2620?

Don't design a house with two intersecting metal roofs on the north side of a house in snow country. Heavy stuff too.

I am building a cab for my B2620. (See thread here). http://www.tractorbynet.com/forums/build-yourself/300825-diy-cab-kubota-b2620-3.html I want to put a heater in it and need help / info regarding plumbing the heater hose. I'm looking at the Maradyne universal which has 5/8" heater hose bibs...

Learned an expensive lesson this week. Pushing snow last weekend and all of a sudden I see a wave of Rimguard swosshing down the driveway and a frightening lurch feeling like the tractor will lay over on it's side... $250 later and a service call later, I've learned that I let the pressure go...

Looking in the engine compartment today of my B2620, I noticed a place on the cylinder head where a bolt is missing. I'm pretty sure there used to be a bolt there, because the area that the bolt head would normally cover is now rusted, as are the threads inside the bolt hole. If there was never...

I've been looking at swapping from R4 industrial tires to turf tires on my B2620 (TLB) this year when mowing season starts up. The R4s are loaded and have worked really well for all the projects I've done, and they have been great in the snow this winter plowing (no chains.) Only downside is...

Thanks for all the posts about home made cabs. A lot of good builders out there. I've started my build but will have questions along the way. My first dilemma is interference on the right side with the brake and the loader joy stick. My original plan was to position the sides about a 1/4"...

I have found a Kubota B2620 used with FEL LA364, and 60" mid mount mower, and it has 363 hours (witch is nothing if well maintained) on it and they are asking $11,900 for it. Another $2,000 for 4-n-1 bucket so that puts me at $13,900 out the door does this sound like a decent deal (new same...

Tractor started up this morning with lights, moved it outside to warm up and after 5-10 minutes the lights had gone off and noticed fuel gauge read empty even though it is full. Then, foolishly, figured if I turned if off it might fix the lights. Now tractor will not start, I get the glow...

I am trying to get a set of armrests for my B2620.The dealer can't find a part number and says Kubota doesn't offer them.He did say the same seat is used on numerous Kubotas but no armrests are offered for any of those tractors.The seat appears to be the same as the one on my previous BX2360...

B2620 owners that have serviced their own transmission - In addition to the spin on HST filter have you found a suction debris screen or magnetic plug that needs to be cleaned? Also how many drain plugs did you find? My manual is very unclear about all this with really lousy pictures too.

Dealer never said anything about it, but I just read the B2620's have a 14.5A dynamo. Is it necessary to upgrade to the alternator to run two extra front work lights and one rear work light. Not sure what kind of lights they are installing. Will be doing lots of nightime snowblowing. Will the...

Before I go and buy a new one does anybody have a front quick hitch for a kubota b2620. I think the model number is B2733A. I'm in southern NY. Thanks!

I am looking at purchasing a Compact tractor for our 4 acres for general utility work. This will be my first tractor so any guidance would be appreciated. I am considering a Kubota B-2620, B2920, or a B2710. There is an '02 B2710 currently for sale in my area with approximately 600 hours. It...

Will a Kubota 60" Front Snow Plow Model B2765 fit a B2620? Which quick hitch sub frame is needed? Thanks.

Do you guys think there be a noticeable difference in the mowing ability of a b2320 and a b2620 both using the 60" mmm on a long gradual slope. I mow about 4.5 acres. Would the three hp come into play here. I think the driveway work would be a wash as well, mostly grading with a box blade and...

Hi, I want to replace mu engine coolant and I am not sure what to use. I just buy this engine coolant (Zerex Pre-Charged Antifreeze/Coolant) and I want to know If it is what I need. I have a b2620. Thanks. :confused: Zerex Pre-Charged Antifreeze/:confused: Protects diesel engines from rust...

Just sprung for the mower yesterday and am hoping the installation is not too much trouble as I have a back hoe subframe installed and also need to be able to install the subframe for the blower/plow in the winter. I am hoping that I don't have to remove the mower attachments this fall in order...

Hey guys i'm at work did a search came up blank. Does anyone know the rops tubing dimensions for a b2620. Making a clamp on radio mount need to mill out some slots just need the W x D. Thank you all.

Guys just got me new B2620 several weeks ago and so far only put 4 hrs on it. Anyway, I mowed the yard twice with it and then took the deck off due to some loader work in very unlevel ground. For the life of me I cannot get the deck installed back on the tractor. I have gotten the deck back...

What should I run the rpm's at on my B2620 while running a 60inch Mid mower? The dealer said 2500 rpm, slightly lower then what the rear Pto calls for.

After letting my wife use my B2620 (I know 1st mistake) Ijumped on it to mow the lawn. The first think I find is the 3pt will not raise the arms so the deck won't come up! I have never had an issue with the tractor and it has around 300 hours on it. If you grab the arms they can be lifted with...

I really hope someone can help me with this. I have a Kubota B2620, 2 years old, bought new, (68) hours on meter. Never had any problems until two days ago. I was using the box blade to get up top soil, and the loader to move it to another area on my lot. That evening I pulled into my barn...

Started accumulating some parts for my SSQA project and since all the factory backing plates and attachments seem to have the narrow "case" holes @21"OC I'm thinking of using this spacing for mine. By using this spacing it will allow my bucket brackets to weld right onto the latch plates...

Heres the setup I added to my Kubota B2620 for rear hydros. Used a loader valve with power beyond fitting plumbed inline between power beyond of factory loader valve and 3ph.

For years I have had a 1991 Kubota B20TLB and a 2000 Great Dane zero turn mower. My zero turn needs an engine rebuild, so I have decided to sell both the mower and B-20 and buy a machine that can both cut and have a loader (i don't need the backhoe). The tractor will be mainly used for weekly...

Just for the heck of it would like comments on the pluses and minus of upgrading from a BX 25 (pre D) to a B2620. Yes, I know I would lose the back hoe which in reality I rarely use. My rational and feel free to shoot it down. First I have a one acre lot but I do help neighbors in the rural...

I recently bought a B2620 with a 54 inch deck.I read reviews on this setup and a lot of people mentioned that the clippings from the mower were quite long which is what I found.I figured mulching blades would help even if I wasn't using a mulching kit.When I called the dealer he said Kubota did...

Hello, What is fair market price for 2013 B2620 with industrial tires, front loader, backhoe with thumb and 60" mower? Thanks y'all!

I have been waiting 3 weeks but finally received a call this morning that my new B2620 with FEL, backhoe with thump, and 54" MMM will be delivered tomorrow. I paid $22,640 for the package with 2 chain hooks mounted on the loader bucket along with the 0% financing for 60 months. Not sure I will...

I received my new B2620 last Thursday.Bought it to do maintenance on my property.About three years ago I bought a new L3240 with FEL and BH to do work on my property.I put about 830 hours on it but now the work is done.The only real purpose I had for it was plowing my driveway in the winter so I...

I am considering buying a Land Pride rotary cutter for my B2620 that I bought last October. When I asked about one last year the dealer said a 48" is the size I need, will the tractor handle a 60"? Any idea what I should expect to pay for one of these. Is a LP cutter a good machine?

I am picking up a "new to me" Kubota B2320 tomorrow morning. It only has 30 hours. It does not have a mid mount mower and I was wondering if anyone has an idea of what it should cost to have one installed at a dealer. I done a little research and apparently the same mid mount mower is used on...

I was just mowing and my 2620 died. Threw the PTO into neutral, turned the key to restart and zero...not even dash lights. Checked the seat/kill switch and wires...looked fine. Cycle the key, remove key...doesn't matter...no nothing when the key is turned. Nothing under the hood appears...

I was thinking I wanted a hydraulic top link, don't think I need a side link but will probably add one later, and I wanted a grapple for the loader bucket so I thought I could do both with one valve by running the lines up to the front and just switching them if I needed a second hydraulic ports...

I've looked all over and can't find details on how the mower deck is mounted. I'd like to know in detail so I can tell what work it may potentially interfere with. Anyone have one that can give details? thanks

Hello all! First of all, I would like to send a shout out to everyone for such a great forum that is full of information and is way beyond my expectations. I am new to the tractor world, so I have been perusing this site for weeks now in my search for a tractor. This is my first post. Just a...

This is a question for the diesel mechanics on the forum. The b2320 is rated at 23 hp/17hp pto while the b2620 has 26hp/19hp pto. Both tractors use the same engine. What differences would produce more hp in the b2620?? Would it be larger injectors? Different injector pump? I know, say with...

There is 3hp differance motor and PTO on these two tractors, is it a noticable differance when finish mowing and snow blowing? I know everyone says go bigger but its around 2500-3000 differance at the dealer I checked at.

I asked this question awhile back and didn't get an answer so I will try again. Has anyone installed the optional Hyd. Rear Remotes on the B2620 or similar tractor? If so can I see pictures of the set up? I would like to purchase the kit but the dealer cant really tell me much about it...

Here she is. Just got it last week.

Hi, I understand from some previous forum posts that the B3200 QA from the LA504 loader can be used on the B2620/B2920. I am wondering if the QA can be bolted directly to the LA364 loade from the B2x20, or if the entire LA504 needs to be purchased. Also, it looks like the smallest QA bucket is...

Paid off my 2008 B2620 today. I got a QA, larger bucket and forks for the loader and it's been a hard working little tractor and I've been able to do a lot around here in the past 4 years including rock moving, landscaping, firewood logging, snowplowing and road grading. It ain't just a lawn mower.

I put a post up a few weeks ago, regarding the price of the tractor. I thought it was about time I put some pictures up of my new toy. Due to the onset of fall / winter I haven't used it very much so far but the little bit that I have used it I think it is going to be awesome.

I have a Kubota B2620 with 250 hours. It will not crank. Removed startersolonoid and had it tested by Pasco . Said starter and solonoid work fine. Reinstalled. Checked safety swithes by turning ignition on and without sitting on seat, pressed HST pedal back and forth and heard relay click...

I have this B2620 that has a BH. Wondering how difficult it is to remove and re attach. You owners of B2320/2620/2920 that have a BH that you have taken off and re installed, what do you say? I had a BX25 but never removed the BH. Had a BX2660 and removed the front bucket one time and like to...

Does anyone know a trick for getting out of being stuck in low gear. I have a HST tranny and I can move the range leaver to High, Medium or low, but the tractor stays in low. The Range gear shift leaver does not feel like it is engaging correctly. The clutch is working OK, not sure what is going...

I have just bought my first real tractor a B2620, I have been looking at tractors for years. Mainly looked at the BX series but when it finally came down to it I went for the B series, I just thought this tractor will be better for me in the long run. At this point I have the bare tractor with a...

I have started working on a custom snow blade for my tractor and figured I would share. I ended up buying two old Kubota blades back a couple of years ago for my bx2200 and used the best parts for it but sold the bale with the tractor. Now I have been kicking around to buy a new one or make the...

I wanted to introduce myself because this is my first post. I currently have a 2012 B2620 tlb with around 50 hours. I upgraded this spring from a bx2200 that I had added a b601 to by building custom mounts and it turned out very nice. I am a mechanic for a major utility company for 13 years. I...

Here is my old thread where I was looking into a tractor for my 30 acres. http://www.tractorbynet.com/forums/kubota-owning-operating/232780-bx2660-small-farm-use.html So the Kubota guy just called and said all the paperwork went through and I should have my tractor Friday. I'm picking up a...

I like the basic size of the B series.... good for my pupose, I think, of crawling around in my woods and clearing things. The tire size looks right and the ground clearance, too. The B2620 look like an economical option. The John Deere dealer is very, very convenient to me....and would...

Have a new B2620HST which has 1.3 hours on it. Hit the key and instant start, let it warm up a bit, start increasing throttle and seat feels like a high powered vibrator has been turned on at around 1400RPM:confused: and up to a bit over 1800RPM and then it smooths out.:confused: This isn't my...

I've checked my fluid level, it's fine. If I raise the deck within 30-60 minutes the deck will be on the ground/garage floor resting on it's wheels. Nothing in the manual about this, where should I start? It's not an issue when mowing as it rolls on the wheels at my cutting depth )3") but...

I am close to getting a B2620. I am giving the Blue dealer one last chance to show me something but unless my socks get blown off it will be a 2620 and based on my experiences it will be orange for me. The B2620 seems to be a pretty good meld of $ vs size vs function. Sure there are some...

I am looking at purchasing a used b2620 and wanted to get a price check. The tractor is a 2008 with 350hrs, it has the la364 loader and BH65 backhoe, Turf tires and a 16" bucket. The tractor looks like it has been maintained though does show some signs of use. It has a few more hours on it that...

We bought a new B2620 with a 60" mower a couple months ago to use primarily as a mower. About 3 weeks ago after my wife finished mowing I noticed the left front anti-scalp wheel bracket was broke. The weld joint broke on the end nearest the wheel. (not where it welds to the deck) Upon closer...

Please help, I have read about checking the switches and jumping them, Fuses are good, moved the various control levers. What else possibly could I check for the reason of the starter not working. Started well all day.

Anyone have any idea on how or if its possible to use this B2620 to lift a pallet weighing 2000 pounds? I have seen somewhere a 3 point fork lift attachment that has its own base? Any thoughts? Thanks Brandon

I just bought a new B2620. Since we are going to use it for just mowing the first thing I wanted to do was take the 3 pt arms off so I didn't have to worry about backing into anything. The dealer said if you take the arms off the deck will not go up or down. What kind of hokey deal is this? Does...

I went to change the fuel filter element on my B 2620, and I can't figure out how to get the element out of the bowl. I did not any force, because I did not want to break the bowl-it seems like the element has to be pried out of the bowl-any tips or pointers on how to do this? Thanks, Will

Hi Folks, I'm looking to buy a B2620 in Northern VA and received the following quote: B2620 HST Loaded R-4 tires LA 364 loader RCK60-29B 60" mid mower $18,400 (pre tax) Does this sound reasonable? Would you purchase the rear remotes with the tractor or add them later (I want to add TnT)...

What would one expect to pay for a used B2620 with a 364 FEL, BH65 and a RCK 60 MMM? Used with only 50 hrs. on the machine.

Hello, has anyone had problems with their rear wheels not centering on the hub, and having no tapers on the rims, for the supplied taper nuts to sit on? Just curious, as mine was like that, and I had to get the rim tapers machined by a machine shop, and also had a sleeve built to put on the hub...

I was out mowing for the first time this year. The tractor started up fine, and was running great. Then I cut it a little too close to an old satellite dish and smashed a rear turn signal ( the square one on the ROPS). I jumped off the tractor to inspect the damage and the tractor cut off...

I've not seen a recent price on the forum and wanted to see if $17900(from the local dealer) was good for a B2620 with MMM and FEL. I have a quote from Barlow's which only saves me about $600, but that will mostly be eaten up by delivery fees. Thanks in advance for any help/feedback.

Buying my first tractor - well, something to maintain just over 4 acres - 3 plus acres of pasture and two 1/2 acre paddocks. One acre is wooded area, sloped and one pretty sizeable slope in the big pasture. There are some tight areas I would be working in the paddocks. I have a Cub zero turn I...

I've used the search function to no avail.... What parts should I be ordering to get rid of these ridiculous turn buckles on my B2620's 3pt hitch? I'd like to get them ordered for when my tractors in for the third function install.:thumbsup: Thanks

I've been busy over the last few months getting my B2620 ready for snow blowing this winter including installing a Sims Indy Cab on my B2620 (that I bought at the beginning of this year) along with a number of other modifications (horn, alternator, electrical wiring, heat, LED lighting, control...

My wife got me a B2620 with FEL and blast box for Christmas. This is my first tractor and what things should I have on hand for regular maintenance? The main objectives for the tractor is plowing the 800' paved driveway and clearing snow around the barn and horse paddocks. I will also use it for...

I am looking at an 08 B2620 with fel,60mmm,and bh65 hoe with 87hrs. What is a good price. I post this before and used two different model of tractors. Which is confusing and probably why I didnt get any response. Time had passed and was to late to edit. Thanks for any help you can offer.

Proud new owner of a B2620. Decided to stick with the MMM because the tractor will spend most of it's life mowing grass. I traded in my JD X540 on it. I had a JD 3320 Cab tractor for years, and foolishly decided it was too much tractor for my 12 acres. I've seen the error of my ways, and...

I'm currently in the market for a rear blade to use on my B2620 for snow removal during the winter. At the moment, I don't have any plans on using it for anything else except snow removal, so I'm not sure what to look for in terms of important features. The only requirement I have is that the...

I just bought this tractor and it only has 115 hours. Tires are like new. I would prefer turfs. Thanks.

I found a used 2008 B2620 with about 120 hours with LA364 loader and 60" mid mount mower. I haven't looked at it yet. What do you think is a fair price? He's asking $13500 or best offer. I have been planning on buying a new B2920 with loader and 60" mmm, but this sounds like it would work for...

I have a 2620 that recently has been shutting off when i get off the tractor. This happens when the PTO is NOT running. In the past i just figured that i was bumping the PTO level and usually i would jimmy the shifter around a awhile and it would then start. Yesterday this was not the case. I...

Okay, there is this strange section in the service as required part of the manual called Draining Clutch Housing Water. It states that there is a drain plug in the bottom of the clutch housing, and to drain the clutch housing whenever you operate in rain or snow or wash the tractor. Is it only...

Does anyone have pictures of the Rear Aux Hyd. kit you can get from Kubota for the B2620? I was looking into this kit but wanted to see pictures of the set up first. Also with the B series and the backhoe is this the kit that is used to power the backhoe? Thanks Brandon

I have a very small utility trailer but could use a larger one for general use. I've been eyeing the 5x10 trailer with a 3500lb axle at TSC. Question is would my Kubota B2620 be okay on it for occasional trips like for service? roughly speaking the tractor/FEL/loaded tires weighs about 2400...

for anyone that is interested I have a factory repair manual for a b2620 it is in pdf format 15.4 megs long It came with my new tractor . only problem is I am on dial up my tie up this pc for some time maybe I could send a copy to some one and they inturn could resend...

Just finished my B2620 first major maintenance...all in all, not bad....I was a bit disappointed when I called my dealer and asked them what they would charge me out-the-door, and they gave me the big run-around about not being able to give me a firm price...c'mon guys...we know exactly what...

Got a chance to mow about 2 acres last evening. I was originally having the issue where the deck drops when lowering or when running over rough terrain. Dealer came out last week to repair (Messicks). Whatever Les did was the ticket! The control knob has basically zero play in it. It feels...

I'm looking at both these tractors and gotten prices on both. Kubota B2620 w/FEL, Turf Tires and 60in mower = $17450 John Deere 2520 w/FEL, Turf Tires and 62in mower = $20487 Both have 0% financing (Deere 48months/Kubota 60months) I've looked at the specs and both are very similar. On paper...

Howdy ya'll. :laughing: I've been kicking around the idea of getting a small Kubota for yard detail and mowing. I already own a L3830 with LA723 loader. :licking: I mow (lawn) around 2 acres weekly and have been using a Toro 270H garden tractor that I bought for $120.00! :cool2: It works...

Ok folks. Two issues today first time mowing. Hopefully this is something I'm doing wrong and maybe you guys can give me a hint. Brand new B2620 with 60"MMM and FEL. Loader is off for mowing today. No problems with that. 1. Sometimes tractor will not start. Turns over fine... Spits a...

Ok folks. Two issues today first time mowing. Hopefully this is something I'm doing wrong and maybe you guys can give me a hint. Brand new B2620 with 60"MMM and FEL. Loader is off for mowing today. No problems with that. 1. Sometimes tractor will not start. Turns over fine... Spits a...

Can anyone tell me the length of a B2620 with a loader and three point? I am patiently waiting on my to arrive and I am looking at storage solutions for it. Thanks Bies

Purchased my B2620 last winter with FEL and MMM. When I picked it up I noticed it had the LA304 loader installed instead of the LA364. When I asked the dealer about it he said the capacity was "nearly the same" and the 304 was "way faster" and nobody wants the 364 because it was slower. From the...

1st post here guys, I've been reading your stuff for a while now, and enjoying it so I thought I might as well join in. I'm not implying I know much about welding just one of the names we call each other at work for fun. Weldoman, weldmaster, weldomatic etc.:laughing: After recently buying...

Is it just me or is the rubber step mat horrible quality? The nipples that keep it secured to the floor of the tractor have crumbled and now it just kind of lays on there poorly. 60 bucks for a replacement also.

Well, I have been hanging around here for a few months not saying much... but I finally broke down and purchased my first tractor Kubota B2620. I am looking forward to it and should have it in around a week. I looked at all the models in my area between 22-27hp and went with the Kubota. I...

Whats the biggest Brush hog mower you could use with a 2620?

Those of you that have either what are you thoughts. I am looking at one of the two. I have 5 acres mainly mowing, some landscaping, moving snow, moving gravel around the driveway. What are you thoughts. I know more hp is always better but if the B2320 will do all the work I need then why should...

Hi folks, new to the forum, but read threads often... I'm looking for a small TLB for landscaping work I do for my customers, but it has to be light enough not to tear up the lawns. Settling on a used BX24 with 100 hours vs. a used B2620 with LA364 loader and 50 hours. I would then buy a BH77...

I have a new b2620 with the quick attach (FEL) from the b3200. It's amazing. There are supposed to be 6 grease points per side on the FEL, but there are only 4 zerks per side due to the QA. It's obvious (black grease collecting dirt) that the QA has two grease needs on rotating pins, but those...

Today I started my B2620 and moved it to a work area. When I went to restart it I only got the click sound but no spinning starter motor. Checked the usual problems (battery, engaged pto lever) but no. Lights work and all fuses are good. I called up my dealer and he and his mechanic advised...

Anyone running this combination? I had the tiller for my BX2350 and kept it in hopes would work ok with my B2620. The tires are wider than the tiller, but tiller is offset so covers one wheel. The B2620 is higher and the rear PTO is higher also. I had angle problems with the BX2350 shearing pins...

Thanks to the collective wisdom of the forum, I selected a b2620 for my first ever CUT. The quick attach suggestion (from the forum) of matching a b3200QA was amazing. The salesman looked at me and said, ...well, never heard of it but its your money... Bucket, QA pallet forks, 60 mmm, 60...

I just bought a 2011 B2620 with R4 industrial tires. Dealer called and said they think they put wrong size tires and wheels on rear of my tractor at the dealer. Can anyone check their tractor that is same as mine and get back to me with tire size? My rears are Good Year, 14.2 x 16, and dealer...

Bought the B2620 in March, and I love the tractor. It has been great. One time while I was checking the engine over I noticed that there was rubber "residue" on the bottom of the hood and on the inside of the side pannels. Strange I thought, and then I noticed that there really isn't much...

Hello. This is my first time writing on TBN but certainly not the first time here. There is a lot of info you guys have helped me with and I am hoping you can help me out with a simple one. I have a B 2620 with about 70 hours. I want to change the hydro fluid filters but I can't figure out where...

well its been a long while since i have posted here. had my bx24 for a few years. i finally traded her in and picked up my new 2620 today. really sweet machine. what a difference from a bx. in any case i was looking at this and realized without a backhoe on it the tractor doesn't have hydraulic...

I just had my new B2620 delivered on Monday and have been reading the manual. It is an HST model. Do you have to use the clutch to engage PTO and the 3 HST speeds every time? Or can you just put gear lever in what ever gear and just pull PTO lever into mid or rear selection? If can use without...

Gonna get one of these w. FEL + 4' RM (bush hog). Dealer thinks 16' will handle it, I don't think so. Here's my situation: I live in MI but will tow this rig 800 miles each way once/yearly to work on my Canada camp. Got a Tundra w. tow package--8300 lb. tow capacity--& will get brake...

I just traded my BX2350 for a B2620. Hope they are a good tractor and no problems with this model. What do you all say? Will my 42 " tiller work ok with it? The PTO is about 3 " higher than the BX was and I had problems with it shearing pins if got to steep an angle while tilling. HJT

Hi i'm looking to buy a new b series tractor ,I tried a new demo unit b2920 last night and realy liked it ,I have a bx25 now and wanted something with more ground clearance then the bx 25,the tractor will be used mostly for grass cutting ,1 acre,and I also have another 5 acres of rough rocky...

The dealer quoted me 17,000 for T/L for the 2620 and $19k for the 3200, I need something with more breakout strength, and more GPM from the pump, the cub is a 26 HP unit but weighs round 1000 lbs, but only 16 pto what do you think

I bought a brand new B2620 with fel and 54" mmm in November of 2010, and what a pleasure it is owning this tractor. I plowed my driveway all winter (and we get alot of snow where we are at) and last weekend I put my mmm on and mowed for the first time with it. All I can say is I am not...

I'm looking to build a hydraulic pressure tester for my B2620 tractor, and I was wondering if I might be able to get some advice on the correct components to use. I'm not sure exactly what the QD fittings are, but I believe they're the same as on the BX-series 1/4" - it looks like Snap-Tite...

Finished stacking the wood for next winter today. The B2620 has been a great little tractor. That's the 5 foot "light" materials bucket on there. Four wheel drive backing up that steep little hill with that weight on the front and only a blade on the back.

Hi everyone, I wasn't sure where to post this, so I started in the parts/repairs forum. At any rate, I have a cracked radiator tank and need some advice about possibly sourcing a new one. I don't want to duplicate the responses, so here's the link to my original thread: Radiator for Kubota...

Hi everyone, the radiator tank on my Kubota B2620 is cracked. The dealer is looking at the feasibility and cost of repairing it (i.e. replacing tank). If I end up needing to replace the whole unit, it's a whopping $520 for just the radiator. Question -- are there any good aftermarket...

Looking at upgrading to a B2620/2920 with the FEL, BH, and 60" MMM from my BX 2360 with FEL and 60"MMM. I'm patiently waiting on quotes from Barlow's and my local dealer. I already have a 48" Landpride BB and have placed an order for a 48" Landpride Aerator. Will those be satisfactory with a...

What is a fair price for the new Kubota 2620 with 54" MMM, FEL, Grill Guard and Ballast Box ?? I am located in Rhode Island.

After changing my mind quite a few times while trying to decide which tractor to purchase (BX25->B2320->B2620) and after some not too difficult "up selling" on the part of my wife, I was finally able to make up my mind and decided to purchase the B2620 TLB. After about 2 weeks of waiting for...

Does anyone run chains on a B2620? Do you have clearance without wheel spacers? I am considering geting a set of chains for my tractor, probably 2 link v-bar chains for Tirechains.com. I used those chains on my BX 2200 and was very impressed by them. I have read many posts about people needing...

I am selling my B2620 i have a new tractor on the way and i am hoping to give someone a great deal before i have to trade it in. it has 236 hrs, 4x4, 26hp diesel, r4 tires rears are loaded, loader, 54" mid mount mower, very well maintained 12,500 is the price

I am selling my 2008 B2620. I purchased it new in 2008 and have been very happy with the machine i am just going a little bigger. It has 236 hours, 4x4, 3 cyl diesel, LA364 Front End Loader, and RCK54 Mid Mount Mower, R4 Industrial Tires with loaded Rears. I have taken very good care of this it...

I'm looking at options to replace my BX24 with a machine next stage up. The backhoe is fine on the BX and given the option, could I use / transfer the BH on B2620 or even a B3200? I'd rather that then buy a new BH for a new machine (lots of coin). As stated, I'm just looking at options...

I am looking for someone that has made mount to attach an old truck snow plow to a kubota b series, looking for some different ideas and pictures to fabricate mine

Got a quote from the dealer of $22,300 for a b2620 w/ loader and backhoe. I went for it. Seemed to be in the ballpark for this area (NJ). Any comments are welcome. Thanks

I thought it might eb a good idea to keep you guys posted on me experiences with my new B2620. I have had it for three days and really put it through it's paces. No easy life for my little soldier of orange. It's not a new tractor anymore... I are about six hours on it now and I have had my...

I have turf tires on my B2620. Most of the time they are perfect for my uses. The only time I wish the tires were agriculture tires is when I'm using ground engagement equipment (eg plow etc.) I am considering getting a full set of tires and rims that I can put on my B2620 when I need them...

SO i have a 2620 with the factory LA364 loader and 50in bucket. I would love to have a 60 inch bucket for lighter crap and the 50 inch for heavy stuff. anyone know what options i have? Can i buy a 60" bucket and make brackets? is there a quick detach out there? I am new to this and have no idea...

Subject says it all... Can it be done? I'm not at all familiar with the BX backhoe, but I'm wondering if I come up with the subframe for a BX and adapt / fabricate it to fit the B2620... Then theres the hydraulics, does the hoe tap into the tractor hydraulics or have a seperate pto driven...

I'm upgrading to either a BX2660 (probable) or a B2620(possible). Final pricing will carry some weight - utility/versatility will, however, guide my hand. Grass cutting around the house has has slowed considerably. Although I will add a cutting deck (54" or 60") to one of the above, I will...

Hi Well after having a second stroke I have decided I need to sell my tractor. My health gets worse not better and do not want wife to have to try to sell. I am going to price it right so I hope It sells quick. Tractor has less than 10 hours so it should make someone a great deal. Life throws us...

Hi Due to my health getting worse I am selling my 2010 b2620. The tractor is a month old with less than 10 hours on it. Tractor just came out of crate a week before I got it. The tractor has a transferable 3 year factory warranty. It has the r4 tires on it. List was 13902.00 First 10,500 cash...

I have 10 acres, finish mow about 2 acres, "rough mow" about 3 acres, garden of 2 acres. I have a Case 530 ag tractor i use for fall plowing, discing, prepping garden. Had a JD317 lawnmower but that is getting pretty worn. Will keep the ag tractor, looking for something to mow, landscape and...

What would be a good size landscape rake for a B2620? Will be removing branches and debris from a couple of areas where we have bulldozed. Thanks for the help in advance. Bill

I just got a new b2620 and have a few problems with less than 1 hour on it ! First is radiator leaks at top tank, Dealer came and looked at it and says yeap those radiators are junk ! Thanks alot, sure didnt charged junk price for it!! Second is the 3 point doesnt work right. Moving it up seems...

I did my first paying tractor job today since I have owned my little B2620 tractor. I tore down a shed and am building a new one for a customer about 2 miles away. The ground was uneven and messy and there were some rocks and footings left I could not move by hand. I tried to get a guy...

When I remove the FEL from my B2620 the colour coded plugs that are supposed to be inserted in the male and female hydraulic connectors to protect them (Caps and plugs) won't stay in place. They pop off the connector as quick as I plug them in. Has anyone the same problem and has anyone found...

When I remove the FEL from my B2620 the colour coded plugs that are supposed to be inserted in the male and female hydraulic connectors to protect (Caps and plugs) them won't stay in place. They pop off the connector as quick as I plug them in. Has anyone the same problem and has anyone found...

The new B2620 was delivered yesterday, FEL, MMM and box scraper. Mowing the lawn took less than 3 hours compared to 7 on the JD L120. Did the initial revamping of the 900ft driveway and moved a pile of soil already. At this rate I'll be scratching off most of the Honey Do List by the end of the...

Dear Kubota: Why did you put the loader brace over my drain plug? I had to remove the MMM and the brace to do a simple job. :confused2:

Well, I just signed the paperwork this morning for a new B2620 with FEL and 60" MMM. Was going back and forth on a few models, but decided the B2620 was best suited for our applications (my wife needs to be able to use it and figured the MMM was better suited for her needs). I think the B2620...

Friday I ordered a B2620 with 60" mower deck and a LA364 loader. It is replacing a red Farmall Cub with belly mower that I have used for over 25years. I forgot to check to see if the B2620 has a drawbar for pulling or clevis work. I know it has a 3ph, but is there a center mounted drawbar? I am...

:confused3:In looking over the literature on the B2620 tractor I could not find if the engine is a direct or indirect injection system. Just wondering? Not that it really matters but I have read that the direct injection gets better fuel economy and does not require glow plugs. Trying to compare...

My First Post! Shopping for my 1st Tractor. Considering Kubota B2620 or, at roughly the same price, the B3300SU. Need lots of advice! The B3300SU has no mid-PTO, but I'm not that familiar with what implements, other than a mid-mount mower, might use one. I will be starting out with a self-feed...

Hello everyone and thanks in advance for your input. This will be my first tractor buying experience. Please excuse if some of my questions have been answered in other posts. I have decided to get a kubota and like some others on here, am trying to decide between a bx2660 and b2620 model I...

Ever since I was a kid plowing the 400' driveway with my dads B7100 hst I wanted one. He's had his for 28 years and since he's not giving it up, I had to buy my own.:D Yesterday I pulled the trigger on a B2620, FEL, Woods GT52 tiller. I don't have as much land as my dad (about 1 1/2 acres vs...