transmission

I have a Transmisson on a Cub Cadet riding mower model TL-200D (787T0124021) that is not going forward or reverse. I started mowing for about 10 minutes forward was working fine. Reverse was really slow. Thought there was grass build up where the reverse stopper is but it was clean with no...

Hi everyone. I have an LS MT125 that I got for cheap. The problem is the transmission is in very bad condition. The previous owner hit something with the hydraulic oil filter (no guard installed) and ran it out of fluid. Then kept trying to make it go until it started making very bad noises...

Hi everyone. I have an LS MT125 that I got for cheap. The problem is the transmission is in very bad condition. The previous owner hit something with the hydraulic oil filter (no guard installed) and ran it out of fluid. Then kept trying to make it go until it started making very bad noises...

Hey all, Looking for some input: I have a vehicle known as a Coot ATV that I am in the process of repowering. I would love to change out the old 2-spd transmission with a hydrostatic drive pump/motor combo but i'm having a hard time finding suitable options. I figured that the folks on the...

I’m needing a transmission for YM2610 Hoping to find someone that has junked or unwanted 2610 tractor thanks in adv Hal Blakely Woodville, Tx 75979

8560 New Holland Range Command transmission W/EDC 13500hrs+. Faulting F1D “Clutch D open or short to ground” Background: This fault has been around for years amongst a multitude of others along with a failing fuel pump had left tractor largely unusable for the last 10 years. Now I’ve moved...

I’ve got an older 3016 shuttle with no reverse. Figured by the time I remove trans & replace problem, it might be easier to replace trans. If I can find one reasonable. Also I like have a book Manual Any help with my No reverse would be appreciated Thanks Hal Woodville Tx 75979

I am working on a ym180d , Can you tell me what type of oil is used in the gear box?

Does anybody know where I can find the vent on an LK3054? If I can not find it I am going to drill a small hole in the transmission fill cap. Thanks, lsr

Anyone ever have the pleasure/pain of driving one? Or know the transmission extensively? Not an 8LL, 9 speed, 10 speed, 13speed road ranger or 18 speed. Those are great, but wondering if anyone has ever driven a Eaton Fuller 7 speed? It’s a twin countershaft transmission, model # T14607B I...

Hello! My Case IH STX 450 doesn't move. At first, the error code was 56016. We took out the potentiometer at the clutch pedal. There is 8 volts in the wire. If we reinstall it, we can't calibrate it. The star (*) does not appear on the calibration display. However, if we take it out and use a...

When I brush hog I want my mower running at 540 rpm. all the time. If I hit a heavy spot, I want to slow the ground speed down but leave the PTO at 540. I have to clutch and shift to a lower gear. Is it the same with the IHMT? If I understand correctly, you can remove the IHMT without...

One for the knowledgeable Ford/New Holland folks. I have a 1997 545D withe 8spd automatic transmission (shuttle shift?). The tractor is a keeper, and that transmission is awesome. A dealer I met said that parts are no longer available to fix that tranny, and should it go it will be unrepairable...

I have a Long Landtrac 470 with a Mitsubishi engine and transmission. Trans is 4 speed synchromesh, with high and low range and a creeper with high and low, so 16 speed with a synchromesh shuttle. The transmission will not shift into 1st or 2nd, 3rd and 4th work fine. It does not grind, just...

Folks. My MF1840M has only 100 hours. Hydrostatic drive (not shuttle) Aside from loader Ram issues emerging in the first 50 hours (crowd rams not holding pressure, leading to oil leak which was traced to back seals not being installed in the factory !!!!), the most recent issue is the tractor...

My previous post was in search of a shift gear for my Iseki TX1500F transmission. Thanks to (Tractor Tech), it appears I found a replacement. My only question now is “what is the best way to access the top shift sliders. I was thinking, which got me in this situation to begin with, to separate...

Hi There. New here. Trying to sort a friends 5610. Got it running but something in the trans is baffling. Downloaded an e manual, but seems to be for wrong Gen. There were at least Gen 2 and maybe 3(?). So the answer is not in there. To do with gear selection. Have got it running by not using...

I have a 2007 RTV 900 2200 hours diesel, an issue that just popped up...when its cold, I put it in gear and it will take off and travel as normal but as it warms up transmission starts slipping and engine revs up but it won't go no matter what gear your in. Has been working fine now this...

I have a 2001 dk55 that is stuck in neutral. The shifter feels loose and its not even trying to engage gears. I drained the fluid from the transmission and found a nut and bolt stuck to the magnet. I believe it’s #5 and #6 in this photo. Has anybody had a similar problem or know how hard it’s...

Hello, Does anyone know where I can source a complete center section HST ? The input shaft on mine broke just out of the blue one day. I bought a new one, gaskets, HST oil etc... took the back plate off to find shrapnel all through the trans and teeth missing off of the PTO gears...Anyhoo I...

New to the chat. My 2006 Kubota Transmission fill port has a hydraulic return line attached to it. How do I fill the transmission with fluid when I’m changing the fluid? Any advice would be appreciated

I don't see anything in the little window so I called the service department where I bought my tractor. He told me the fluid is clear and unless I know it leaks it should be fine. No dipstick, why is there just a 'window' if the fluid is clear? Pictures for your perusal.

I asked this question over at "Owning/Operating" but got no hits. Hope I have better luck here. The attached photo is of my transmission sight gauge and I'm trying to determine if the trans is overfilled or low. This is a TYM T1003 (100hp) and there is no dip stick. I don't remember if...

Have the known transmission issues on the NX-series been corrected at the factory level yet? I understand Kioti is cancelling the NX-series but I am considering a new NX6010 HST ROPS currently.

Had A reason to refill my 1963 transmission oil the other day. Had to refill my roll around pump gear oil device. So I was reading the label 80/90 GL5 telling all about extreme pressure and so on then it said for use in non synchronized transmissions. What I thought. So I call the local...

Im about to bite the bullet and drop the 48re trans out of my 2006 ram 2500. Im thinking Im going to rebuild it myself. Ive looked at a bunch of parts kits and videos. Ive done a bunch of engines, a few vw transaxles, but never a auto trans so this will be an experience. Looking for ideas to...

I have a Hustler Raptor SD 54" (model year 2018) mower and when I shut the engine off, I hear a loud rattle around the engine or transmission. It sounds like there's play in the engine or somethings loose. It's very loud and lasts a couple of seconds. It doesn't sound like a loose bolt, but like...

I am looking for a seal kit / rebuild kit for the hydrostatic transmissioin pump for a Cabela's LM50H. Can anyone help me with this? All help would be greatly appreciated.

Hi, this is my 3rd year with my oil looking like this. It is full of little bubbles. It starts after a few minutes of running the tractor and clears up after shutting it off. While running the sight glass fills up with tiny bubbles. We have confirmed it is not a water issue. Seems to be air...

Parked my tractor 2 months ago with no issue. Went to use it and wouldn’t go in gear for 30 seconds. Both forward and reverse. While moving would loose power and stop moving for another 30 sometimes longer! Can hear a whine from tranny area. Changed oil and tranny filter still the same? Any...

Wondering if I can use Castrol UTF in my hydrostatic transmission for the transmission / hydraulics in my Emax 25? Manual says to use API GL-4 grade, 80w gear oil. Can't find these specs with the castrol. Thanks!

I have a 2011 JD 3320 eHydro with just over 500 hours on it. I've been using it regularly of late to move mulch, bush hog fields, tow a trailer around the yard, etc and no issues. When I went to do some tilling today the forward motion stopped suddenly – forward and reverse pedals did nothing...

New to the forum, hoping one of you transmission (HST) wizards will be able to help me out. I have a 2003 Kioti CK20H tractor. The main shaft (Pump) spline teeth wore out and has to be replaced. In removing the piston block assembly from the swash plate, the spacer pins fell from the assembly. I...

New to the forum, hoping one of you transmission (HST) wizards will be able to help me out. I have a 2003 Kioti CK20H tractor. The main shaft (Pump) spline teeth wore out and has to be replaced. In removing the piston block assembly from the swash plate, the spacer pins fell from the assembly. I...

Hey all, realized hydraulic filter has never been changed. can't find replacement info, anyone get one recently? Need to replace 4wd oil seal also. Is it difficult? working my way through all the leaks LOL. Need to do FEL o-rings also and a bunch of hoses. Just got new tires. trying these...

So I have a Kubota b7500, (not sure what year) and I took the gearbox under the seat apart to replace the arm main **** pin, but I can't figure out how to get it all back together, there was this little ball that fell out when I popped it open and now I'm not sure where it goes, any ideas would...

So I have a Kubota b7500, (not sure what year) and I took the gearbox under the seat apart to replace the arm main **** pin, but I can't figure out how to get it all back together, there was this little ball that fell out when I popped it open and now I'm not sure where it goes, any ideas would...

A friend has a L3301 with the hydrostatic transmission. The two lines with three connections shown in the attached pictures are leaking where the bolts hold them to the filter base/housing and the transmission housing. It looks like to me that the fix would be to replace the O-rings is that...

HELP! : Massey Ferguson 1160 : SLOWLY LEAKING transmission fluid, can’t find leak! Suggestions??

How much gear oil is required? 2001 mahindra 4005

Question on my 503 tym hydrostat works when first started forward and reverse and then the forward reverse quits. all the other Hydraulics work normal. Last year it was in the shop for 13 months waiting for tym to figure out what the heck was going on with it and supposedly it was a loose...

Hello I am trying to find somewhere to purchase a Yanmar YM165D Transmission dipstick for my father's tractor. Does anyone have a recommended parts supplier, or even the part number for that item would help a lot. I am in Australia, but if it can be shipped in to Australia somewhat cheaply, I...

While doing backhoe work went to move tractor and it would not move. I had this happen last fall and found the roll pin that holds the shaft and lever together had fallen out i was able to replace the pin with a bolt and nut, this time the shaft will move but it will not engage wheels all other...

I own a yanmar 1500 with transmission problems, tooth missing on 3rd gear and bearing noise. I found a ym2000 parts tractor and was wondering if the transmissions are the same or completely different between the two. It only has 240 hrs and is a great little tractor with a loader, but it seems...

I wanna introduce myself, I have a small acreage on Vancouver Island. My 1970ish Kubota L225 has finally quit on me. To be precise the transmission has quit. I have owned for about 15 yrs and have only ever had two forward gears,(4 if you use hi/lo) and reverse. Now it’s finally quit. Does...

I have a 91ish L3450 tractor, Recently using my backhoe, with the engine idled up, I could hear something sounding a little marbley. I idled it down and moved the tractor and it stalled. First time it ever did that. Drove it to my garage and it was bucking a little bit while driving. I pulled...

I am looking for a good 8-speed transmission for this tractor. Can't seem to find much parts for this tractor.

I had the transmission rebuilt with a lot of new parts summer of 2020 and now it is stuck in 4th gear. Since 2020 I just tried to not use 4th for extended time as that was what seemed to cause it to stick. I was always able to take gear shift cover off and use a crowbar and leverage the fork...

Hello everyone, I am new here and I hope you can help me with the following problem A few days ago, immediately AFTER switching on the PTO to drive a disc mower (rear) our renault 540 rx ares gave up. What no longer works: - driving forwards or backwards - PTO no longer works - power...

JD E120 does not go forward or backwards. Do not hear any whirling or grinding sounds just does not move. Tractor can be rolled forward and backward whether the bypass rod is engaged or not. When it’s engaged, there is a little ticking sound as it rolls backwards. From previous car experience...

I just performed a Cub Cadet Zero Force SZ Hydro-Gear transmission fluid change. This was no fun! I found a great 26 minute detailed "how to" video on YouTube - - and tackled the job on my 540 hour mower. Never been done before, although I've done regular engine oil and filter changes. In a...

I am trying to do a 200 hour service on my B2620 and I'm getting confused about the relationship of the transmission filter, the hydraulic filter, and the hydraulic fluid. The manual shows a 200 hour service interval for the transmission filter, with accompanying drain plugs. It also shows a 400...

I resurrecting a Bull and the tranny is frozen/rusted together. What would be a good method to free this?

Looking at the OEM manual but having a hard time figuring out which bolt to undo to get to the transmission strainer. One drawing shows it by the filter. Another seems to indicate it's on the other side of the tractor. Thanks in advance for your help! I need it!

I have a very broken dk55 that has a broken Transmission middle case, part # T4682-21157 which the dealer can not source. If anyone knows how I might find that part new or used, or even a transmission please let me know. Original part was T4683-21154 Regards, g

does the transmission hydraulic fluid operate the rear hydraulic lift on a 2200D Yanmar tractor?

Hi, I have a f16d tractor was using it today and switched between reverse and 2nd and it kept going backwards. If it try to put it in 1 or 3 it will stall out if i out in the 2nd spot stays reverse. Is there a linkage between the pin the shift moves and a gear somwhere? Any help sith a...

I just replaced the neutral safety switch. Hardest part of the job was getting the cover back on and everything aligned properly and keeping the darn gasket in place (and clean). I have the bolts snugged down and verified that the new switch works. The old one was intermittent, so hopefully...

Was using tractor and both hi/lo switches stopped working , noticed when i push them rpm gauge jumps around and battery light comes on . Any suggestions

Is there problème whit 2010 1652 Massey Ferguson 4x4 transmission??

I have a nose coming from the transmission area of my MF 1030. It continues even when the transmission is in neutral. Throw out bearing??

The turtle lights on the dash push button will not shift up. Was told could be the rabbit button or the solenoid which I can't find them.. Any ways to test this stuff?

I have a 2006 Massey Ferguson 492 4wd with 1070 Loader and Cab. The perkins diesel engine runs very well and has been gone through already with cleaned fuel tank, cleaned fuel lines and injectors, along with a new injector pump (old stuff damaged prior from bad fuel). A new clutch has also been...

Hello I have a bobcat ct445 open station with loader. I am in need of someone that can rebuild the hydrostatic transmission or has one I could purchase. Or any tips would be greatly appreciated. I am located in central Kentucky. Thank you!

We were seeding and while turning around the tractor 'popped out of gear', anyway, it stopped moving forward. No broken linkages. Steering and loader no longer work either. Valves still work for loader will go down. It was running warm a few times because of plantmaterial on screen; removed it...

I have a s-373D and all of a sudden it will not shift into any gear. With the engine on and the clutch depressed I hear grinding when I try to shift into a gear and am unable to shift into any of the gears. It is the same sound and feel as with out the clutch depressed. The PTO is functional. I...

I lost ability to shift powershift transmission. I get TRANS 75 error code: "TRANS 75 Engine speed from Inst Controller does not match the speed signal from the alternator.". I was told this was due to faulty shaft speed sensor on left hand back side of transmission or the wiring...

Hi all. I bought an industrial loader/backhoe from a local meat packer last week that was advertised and sold as a 1980s Ford 755 for $4500. It didn't take me long to figure out with a 3 cylinder diesel it's not a 755. It took me days to understand where people were saying the ID numbers are...

Good Morning All, New to forum, first post. I have a 2006 Cat Challenger MT265B with the powershuttle transmission. Tractor currently sitting at around 750hrs. Yesterday while driving thru the field it suddenly stopped on me. Got it started again and it seems something has bound up in the...

Several years ago I bought a used BX22. Used rough but still in good shape. Had a little feedback when the peddle was depressed fully in high gear. After year one I change the hydraulic fluid and no change. Next fluid change I took out the screen and found a few large pieces of metal in it...

Hello. I have a JD750 20HP compact tractor that just got back from getting the engine overhauled. Engine runs great and blow by is gone. Loader and 3point work fine. I was using it this morning to move some dirt to cover some holes in my drive. Went back and forth from dirt pile to driveway a...

I have a cub 5254 with the dreaded issues... but anything can be fixed... so I am going to **** well try. So what happened? FIRST issue, randomly my PTO went out and appeared that the shaft was jammed and burned up the clutch, the shaft will not turn. What did I do after this? not a **** thing...

I am in need of some assistance. I had to rebuild the t96 3 speed transmission which was a piece of cake for the most part. I also had the flywheel resurfaced and got a new clutch kit. The clutch kit came directly from the clutch factory and not through Vermeer. I installed it and it seems like...

Looking for a mechanic in Central Florida that is familiar with this transmission.

Can't find any other threads on this, but does anyone have any ideas to get the tranny out of Turtle?? I tried rocking, both gently and vigorously, but to no avail. I often run across town with it, and it's a fifteen minute trip in low. (yes, it's a small town.) Any ideas would be welcome...