Hi all, I have a 1965 Massey 35 with a petrol (gas) engine. Being in Australia, the engine is a Standard 87mm, which I believe is different to the Continental that North American 35's have. I'm...

I just bought a MF 35 tractor with a loader. UGF 655000100 It’s in rough shape but it starts and runs and the loader works. I don’t know the exact year it is a gasoline engine and as near as I can...

Hi, I have a MF35 with a front end loader fitted which requires new front tyres. I was looking for some thoughts on what type of tyre to choose, particularly around the choice between tri-rib or...

Our house and outbuilding were destroyed by a tornado last Friday. My wife and I were home with four of the kids and thankfully there were no injuries. The MF35 Utility survived, despite the...

Good evening, I finally got around to pullin my pump and watched several YouTube tutorial's on how to do it. This is on a 3 cyl perkins The good news is the leak seems to be fixed and it started...

Looking for new multipower parts to fit to a 35x as it had previously been disconnected

Hello I’m new to all this so please excuse anything I’ve just overlooked. I have a 1964 MF 35 - I’ve recently replaced the lift pump (it wasn’t delivering about fuel to the engine which kept...

I've also posted my 8n HERE This restore happened over several years and 3 owners. The person that started it did an amazing job. Way better then I would have. They rebuilt the motor and tranny...

Hi, I have a 1962 Massey 35, UK built, that has some hydraulic pump issues and needs repair or replacement. Massey have 3 Marks of pump of similar size and shape and I don't know how to identify...

Hi, I had this posted in Massey Vintage and no replies so trying here instead. My MF35 has lost it's lift power on the three point linkage. I occurred after I was installing a diverter valve to...

Hi, My MF35 has lost it's lift power on the three point linkage. I occurred after I was installing a diverter valve to the the external cap. The stand pipe was lifted clear when the external cap...

Hi, I recently purchased a loader from an MF35 to fit to my MF35. Loader fitted well. It's old school, but so is the tractor. Problem is, I can't get any action on the hydraulic rams. Set up is...

Hey guys, I recently posted in the Hydraulics forum but haven't gotten replies yet. I'm hoping that by posting here in the MF forum, I can direct some attention to my post over there (click here)...

I have a Massey Ferguson 35 Utility tractor with a Davis 99 loader. The bucket sags off with any load on it and my testing shows that it's the control valve, not the cylinder. I was reading...

I want to remove the engine cover (hood, bonnet, whatever you want to call it). I am on my own for the moment, am I likely to manage it myself or should I wait until I can find a helper? I was...

Ugh. So here's the scenario- I was using the flail mower to cut down some tall grass, cut some paths through my field. Was running the machine for maybe 1.5-2hrs. Temp gauge never moved, oil...

I would like to buy and use a hydraulic post hole borer to run on the front loader of my little MF35. I know the stock hydraulics won't run one, the auger I am looking at ideally needs about 35...

I took the fuel tank off my MF35 to (try to) repair a leak. Ouch, it gets expensive when gas is leaking out of there! I see the valve covers are now accessible. Does the gas engine require...

Hi, I am working on a misfire on a 1962 Massey 35 petrol (gas) 87mm Standard Motor Company engine and am considering compression issues. It's the low compression 6.0:1 ratio. Does anyone know...

My MF35 Utility (gas engine) leaks power steering fluid. I suspect it's going into the crankcase. I have googled for a replacement seal but am not sure if the MF35 utility uses the same power...

Hi can anyone advise what spark plugs I need for my tvo 35 . I'll be using mainly petrol I guess and the ones that are in now are champion n8,s. Look like they've been in a while. Also any...

I am new to the forum and new to tractoring. I purchase a Massey Ferguson 135 Perkins Diesel and am now looking for a PTO snowblower (we get a lot of snow in Temiscaming, Quebec). I have some...

my 35 diesel power steering pump will not keep fluid in the system. i believe the seal to the pump thru to the block is blowing by.do they make a rebuild kit for this? 773126M92 is the part # on...

I have an fe35 massey that has developed a leak at the injector. It does not appear to be coming from the high pressure line or leak off. I don't think it's coming from the cap either. Can it...

Hi, started the repaint and tarting up of the 835-ds, (which is basically a 35) and so far so good. If you are in europe have to recommend Tracteurbits.com for all old tractor parts. great service...

I have an MF35 tractor with a bad hyd pump. Part #181995 m1. I can’t find one. I have looked everywhere for a pump or pump repair kit with that #. Anyone know a cross over.

Hello all, I bought an old tractor. It's a 63' MF35 perkins diesel with an MF100 loader. It had been neglected but still loaded on my trailer under its own power. I have done repairs to the front...

Hello all, I'm trying to source out new injectors for my 35 perkins. The injectors in questions have an "F" tab on them and I'm unable to find much online. Would anyone happen to have a beat on...

Hi everyone, Hoping someone can help me, I'm currently doing some odd jobs on my 1958 Massey 35 Petrol/TVO and need some help with thread types, sizing etc. I'm in the process of sorting the...

I have a Massey 35 with the 23c 4 cyl diesel. I've been picking away at fixing things on it and have it to the point where it will start well in winter. Incidentally rewiring the tractor an...

New to the site.First off I’m not a tractor guy, but I am trying to sell a 63 Massey 35 that has a new rebuilt Perkins 3 cylinder diesel sitting on a pallet. This was a project for a friend of...

New to the site.First off I’m not a tractor guy, but I am trying to sell a 63 Massey 35 that has a new rebuilt Perkins 3 cylinder diesel sitting on a pallet. This was a project for a friend of...

Hi this is my first post here so hello to all.Wonder if anyone can help is there a list of 3 cylinder diesel 35 engine numbers with year of manafacture?The engine number on mine is GL 1819674.

I am working on restoring a Massey Ferguson 35. Before purchasing the tractor a fire had destroyed the wiring and the regulator/control box was missing. I have purchased a Delco GDR6006 regulator...

I have been using and repairing this Massey 35 Turf for the last few months. The PTO lever has the 3 positions, Ground, Neutral, and Engine. The pto stops when pushing in the clutch as well as...

Thinking I want power steering on my Massey 35 Perkins diesel but I don't want to buy the kit. I can piece this together using a hydraulic cylinder and you can purchase a steering pump that fits...

Hi All, I've become the proud caretaker owner of a 1957 MF35 with loader. It's a 3 cylinder diesel and starts, after laying for over a week, first time without any assistance. Isn't overly smokey...

mine has a single hose(bull?) remote. can i remove this since it isn't used and what do i replace it with? or can i just remove the hose and plug it off?

got tired of that steel pan seat. whats a good way to upgrade to something more comfy?

I'd love to have power steering on my Massey 35 Perkins diesel. Particularly if I find a front loader for it. Would you guys recommend the conversions they sell on places like eBay? See link...

what oil do I use? gonna change it soon, but I don't think mineral oil is still around.it's a 1962 model.

Not sure if this is right place but I came across this Massey 35 for sale not to far from me and it looks like it would be a interesting project to buy maybe, I know nothing about Massey tractors...

Hello guys and gals, I知 trying to get my grandfathers 35 running properly. Bought new in 61 with the Perkins, used all summer to rake but started running like crap awhile ago, fuel knock under...

Need help;I cannot engage live pto it just grates:have adjusted clutch to less than 80thou but no better.It is an after market clutch and only has 1 Bellville spring the manual shows 2 for Massey...

I am replacing the headlights on my MF35 utility. Again. They used to look like this. Then they got crushed when a wind storm blew in the overhead door, which then landed on the tractor and took...

We got buried last night by snow and high winds. When I tried to start the MF35 utility (gas), I heard a clunk and then after that the starter just spins without engaging anything. I pulled the...

Hi guys. Finding it difficult to understand which hydraulic/transmission oil to purchase. I can get this stuff locally and usually comes on sale. Is it ok to use? UNIVERSAL FARM OIL 15W-4...

hi guys, well after completing an engine service after purchasing a MF35 I turned her over and noticed the lift arms were in the top position. I cant recall what levers I pushed next (either...

Hi all, recently purchased an MF35 with a new radiator and water pump. the old owner recommended I drop the water and add 50/50 mix of coolant. The water is quite brown when I take of the rad cap...

Good Morning, I am wondering if there is such thing as too large of a backhoe to install on 35 utility tractor. I bought an older backhoe and talked with some friends about putting it on and they...

Hi all, I have a bit of a strange question! I have a Fordson Major (bear with me my question is Massey related!) that I bought a new tachometer for and after installing it on the tractor it reads...

I'm helping my neighbor to get his old Massy 35 gas tractor going this spring. I can't find where to check the transmission oil level. I've found the fill cap on the top of the transmission, but...

I beleive I just purchased a Massey Ferguson 35 utility with the 3 cyl perkins. Runs and drives everything works great including the front loader but the front axle support frame is cracked...

Helo from Romania, i have a MF 35x , 3 cylinder, perkins , 44.5 Hp Where can I find a parts manual for this tractors (MF 35/35x) Here is an example of what I want"...

I bought a massey 35 deluxe diesel yesterday as an upgrade from my old trusty ford 8n. I dont know really anything about these tractors other than it had 2 things i really wanted over the ford...

I'm looking for somewhere to purchase parts, the parts I need is where the fuel enters the pump, I believe it maybe called the end plate. It has the filter, some springs and a couple of other...

Can someone help deciphering the serial number. it is supposed to be all original. the tag says model TO 35 SDM198921. Which would be standard chassis standard 4-cylinder diesel A two stage clutch...

Bought a MF35 gas with multipower, don't have a SN # tag so does anyone what year they added multipower to 35's, all I have read on forums says 35's with multipower years should have dual stage...

I Bought a 1964 MF35 Industrial Utility / Turf ( Gas ) ( The Yellow One ) for $1600.00. Does not seem to be smoking, or leaking anywhere. The seat frame for the backhoe seat is missing, but have...

I have a 1967 Ferguson 35 and need to change out the PTO seal. I removed the retaining plate but I can not pull the PTO shaft out. Is there some special tool or trick need to do this. Please help...

Hi all, I've recently purchased a 1960 vintage MF35 Deluxe with the Perkins 3A-152 diesel. I have a couple of other machines with later Perkins diesel engines (MF-300 crawler/Perkins 4-248 &...

I think I have overfilled my transhydro and now have hydro oil in my starter looking for info on how serious my issue is it is about a 59 era Massey Ferguson 35 gas deluxe 2 stage clutch I was...

Hi I have just read a thread about someone who has a oil leak on a 135. Apparently at the tacho inlet, maybe 2 oil seals need renewing. I am trying to work out if I have a similar problem on my...

Hi I have just read a thread about someone who has a oil leak on a 135. Apparently at the tacho inlet, maybe 2 oil seals need renewing. I am trying to work out if I have a similar problem on my...

I'm currently doing some tune up work for my father-in-law on his MF35(1963 model). It has the Continental Z134 engine. I pulled a spark plug out today(not sure if they have ever been replaced)...

I got a old mf35 gasser just to bushog with. I don't have a over run clutch for the bushog, mf35 has multipower and I know high locks in the motor with engine braking but free wheels in low so...

I have a MF35 diesel with thermostart(intake manifold heater). The original switch was not wired and does not work. I got a new switch that has the same terminals but I don't know how to wire it...

Hello all Ive bought a small farm where I found an old MF35 petrol in the barn. It started fine, but it makes a strange hammering noise. The interval between two knocks is about a secund and it...

I've owned this MF35 for 9 years now. It wasn't running when I got it but only took routine things to get it going. Replaced distributor caps, rotor, plugs, and worked with the neutral start...

I'd like to know if anyone is using little grey fergies (TO-20,30,35) or Massey Ferguson 35/135's for farming veggies. Specifically, I'm wanting to know what size disc you might be using, and I'm...

Hello everyone, Well the ol' 35 with the 3 cylinder perkins had a bad injection pump, I replaced it with a new one, fired right up after cranking for a couple seconds, but now there is a distinct...

I am looking to by an old Massey Ferguson Tractor. It has a front-end Loader MF 34 L8110 and a Backhoe MF 54 Serial 1409007324. I believe it is a Massey Ferguson Tractor 35, but I am not...

G'day all... I have just put our MF35 Diesel back together after an engine rebuild which included a new double clutch with release/pilot bearings. Engine runs great and very happy, but when we...

Some of you may remember my thread from a few months back: http://www.tractorbynet.com/forums/massey-ferguson-classic-vintage/347197-early-60s-mf-35-utility.html Well, life got in the way for a...

The old Massey Ferguson 35 gets few hours any more, restricted to loading the odd log and powering the winch on its hitch. Without indoor storage for it, I'v learned to deal with a flooded air...

Hey all, I'm losing it right now with my 1964 MF35 Z134. I was disking my garden and the tractor just stopped for no apparent reason after using it for about an hour, no spark. Because I was...

Hi now I ma started

Hey all, I am purchasing a building with a yellow Massey Ferguson 35 Utility in it. I have only been in the building twice and didn't pay much attention to the tractor because my focus was on the...

Can anyone help me out with this please. My MF35 tractor 3 point lift arms raise fine but won't go down. It won't go down even if I turn the tractor off. It has a front loader with a Diverter...

Hi, I have a Massey Ferguson 35 tractor with multi power. I recently had the Diverter valve get stuck in the front loader position. So i took the Diverter valve off and cleaned it out and replaced...

Hi all, I have a MF 35 with multi power that had just started leaking badly from the bell housing. From what I've read, I'm going to have to split the tractor. Can anyone give me a list of parts...

Hi, I have a gas powered MF35. The tractor came with the house when I bought it a few months ago so I don't know anything about it. The Diverter valve is jammed up and only allows me to use the...

Hello Everyone, our Massey Ferguson 35 Petrol/TVO is running very rough. Symptoms: Turns over and starts easily Once running the tick over is uneven and spits back through the carburetor...

My massey 35 steering suddenly will not turn to the left. Turns to the right freely. Anyone have experience with this?

I want purchase Massey Ferguson 35 x Tractor. How and where purchase?

I have an MF35 Utility with the Continental gas engine. The transmission is a 3-speed with a separate high/low lever and shuttle shift for Forward/Reverse on the steering column. Recently I use...

I lost the left capability on myn 1962 MF35 while using a blade. Lift arms will lift with attachment. but fluid leaks out of what appears to be a relief under the left side of the seat. Arms will...

Hi all, My name is Andrew and I'm a first time poster from Ourimbah NSW Australia. My parents own a Massey Ferguson MF35 3cyl Diesel which is of huge sentimental value to our family as it...

I just purchased a MF 35 and I'm wondering what maintenace items I should be doing and what I should be looking out for. I've changed the oil and oil filter, changed the secondary fuel filter...

I am from Victoria Australia and new to this forum. I have a MF 35 with a Perkins Diesel which I have had for nearly 27 years. Not sure of exact model/SN (tractor is not here at present), but I...

I know this has been covered but I am unable to fix my issues. The tranny in my massey 35 got stuck in reverse while in use. I followed the directions that people have supplied regarding moving...

I'm fitting an MF80 loader to my 35, but don't know how to route the hydraulic pipes or where their brackets go on the tractor. Any suggestions gratefully received

Hello I am in need of some help with my fathers 1960 Massey Ferguson MF35 steering. It has power steering with the slave cylinder attached to the steering box. The problem is it will not steer to...

gear oil got added to trans now the 3 point will not lift have taken top cover off and pump is working but not shooting oil out of casing how can i check the pressure being delivered to the...

i have a massey ferguson 35 and its hydraulics arent lowering.... what do i do ???

Lift arms will not raise. Got fluid.

Hi wonder if anyone can advise me, you should know I am a complete newby to tractors. Last year I acquired a mf35 four cylinder diesel, bit smokey but it hadn't run for three years, put away last...

Wanted to change out thermostat on the tractor. Took it apart and lo and behold no thermostat. Ordered a 160 degree thermostat and thought I put it in the right way. Refilled radiator and ran...

My '62 MF35 Deluxe lights are dimmer and dimmer. Now engine has lost power (over half) and misfiring. Battery not staying charged either. How to troubleshoot if it's the alternator or voltage...

I have a petrol Massey Ferguson 35 which I'm thinking of replacing for a couple of reasons. It has small back wheels on it, so the drawbar is sitting at the wrong height to operate my tedder...

:confused:Introducing myself; from Manitoba, Canada. I bought a Massey Ferguson 35 Utility Tractor; front end loader last spring. The tractor runs fine but recently became stuck in reverse. Any...

I have an MF35 with the 23C diesel, its developed a problem where air seems to be getting into the injector pump, causing it to die and I'm continually having to bleed the air out of the pump to...

I have an older (maybe a 53) MF35 utility. The 3point hitch usually won't come up at all. The gear case oil seems to be frothy as if it had water in it. Would that cause this problem? What...

Good Evening folks, I just looked at a tractor today, I have been looking for another older Ferguson loader tractor to add to the stable. I have really been searching for an industrial tractor...

I pulled off the body on my mf35 today to try to figure out where exactly my engine oil is leaking from and to take car a coolant leak from the upper radiator hose. In the process I found I'm...

I have a 35 Massey with the frame for a front end loader and would like to buy all the rest of what I need any help or I will sell mt frames.

Hello, I used the tractor over the summer for brush hogging and it ran fine. I started it up about a week ago and now it's billowing white smoke like a chimney fire out the exhaust. I shut it...

Hi all. I'd like to try running my 35 on home brew TVO, but I've got a couple of concerns before I go ahead. Firstly, the heat shield is missing from the manifolds - do I need to replace this...

I need some help diagnosing this - she's stuck in the middle of the back paddock at the moment with a hopper full of fertiliser :( Was running fine, just spread fertiliser on 7 acres and was...

I am looking for a good reliable source for parts for my MF35 Diesel Deluxe. Does anyone have any suggestions? Thanks

Last Friday I picked up this tractor. The seller told me it was a Massey Ferguson 35. The diesel engine is not original and that it was from a Generator. :confused2: From what I can tell it also...

Hi, first time post, I'm searching to find out the year of my Dads Ferguson35 tractor that he just bought. It's believed to be a mid 50's tractor, the serial # being H154467. If someone could help...

Hi. I need to replace the fuel filters on a Perking 3A-152 diesel, which is easy enough, and will have to bleed the fuel system afterwards. I know how to do this and that's not a problem. The fuel...

Have a massey Ferguson 35 petrol. It use to start really easy , but restored the body and now have two spare wires that come out of the gearbox under the dash area. Unsure were thy connect...

Hi. From the serial numbers and codes I am almost certain that my tractor is 1962 MF35 with the three cylinder Diesel engine 3-A-152 Diesel. I have just replaced the water pump and of concern...

Hi I am trying to repair a mf135. My biggest problem so far is trying to get a manual for the mf135. Massey fergussen here in s africa does not have them and I am reluctant to buy a manual from...

I have a 1955 Ferguson 35 tractor and have found a Kelly 41 backhoe. The tractor has a very heavy Davis 102 loader on the front so my question is will it handle this hoe?

When I purchased my Massey Ferguson 35, the lift would raise and lower, but it was slow and jerky. I just changed the trans/hydraulic fluid and filter and found that there was a good deal of...

Hi All, Just purchased a MF35. The previous owner said that the PTO would not engage, so I got it at (I think) a good deal. Well, I got it home and started tinkering around and found that I was...

I was wondering who has a loader on their MF35 or who knows of a loader that will work well this this tractor. There's a guy not too far away selling a Kelly 800 loader but I'm not sure what I...

Does anyone have a recommendation (and source) for a shop manual for the MF35 gas model? Thanks in advance.

So this tractor has tons of use and is "worn out". But I am trying to keep her in service to keep our acreage brush hogged and some other light work. When brush hogging a pasture I don't care...

I'm adding some rear hydraulics to my 1964 MF35 in preparation for my log splitter project. I was going to run the supply from the divertor valve I have for my loader, but was thinking of using...

MY FERGUSON 35 DELUXE OIL LEAK AT FILTER HOUSING How to fix this. Never leaked before. Now leaking where filter housing seats on engine block despite several gasket changes. ? ? Permatex on both...

Hi all. Following the success of my loader renovation, I am now building a log splitter for my 1965 MF35. I have a valve and ram, but I dont see where I would send the hydraulic fluid back into...

I have an old 1955 Fergson 35 (Massey Harris Ferguson), with a Davis 102 Loader. It has a Cesna 20GPM pump mounted on the front of a recently rebuild Continental 4 Banger engine. I need a hoe...

So I have a new to me Ferguson 35, 1955 Vintage, has the Massey-HArris-Ferguson tag on it, and a Davidson or Donaldson 102 Loader. Got it with the 4 banger gasser engine, the fellow I got it...

I have a Massey 35 deluxe that I recently purchased as our first tractor. I don't have a lot of seat time but when I was moving a heavy 6 ft brush hog I heard what I can only describe as piston...

This is my first tractor and I'm having trouble identifying the year of this tractor since the serial number does not match anything I can find on the Internet. It looks like the original paint...

OK, my MF35 is making so much oil that I have narrowed it down to the Injector pump, I first replaced the fuel pump, but oil/fuel is pouring out of the dipstick hole at around a cupfull per...

The single cylinder bucket that came with my Davis 101 loader has been repaired and modified a number of times and its pretty well beat. Floor is rusty, cutting edge is bad and the mount for the...

Well, my dealer pop tested my injectors today and found one that was junk as he put it. They also dicontinued that part. Can any of you all recomend where i can get a replacement or rebuild? It...

Hi, The pictures below show the cylinder head from a 1958 Massey Ferguson 35 Petrol/TVO. The larger hole with the arrow pointing to it had an alloy "bung" screwed in flush and goes into the water...

I am so confused about the MF 35 Models. The confusion is the 4 so called models of the 35. There is the 35-35X-35 Special and 35 Deluxe. So would somebody please tell me if all these models...

I put in a sealed bid on a MF 35 3cyl. Perkins Diesel with multi power and power steering. No diff. lock. How can you tell if its a 35 or 35X. Best i can tell its a 1961. I saw a 1961 on the...

Hello New to the forum. Looking forward to all the information available. Having a little trouble finding a thread that addresses my issue so I'll post something here and see what happens. I...

I've got a broken piston in the internal pump. Debating whether to buy a rebuild kit, or a good used pump from a local dealer. Difference is about $70. I'd prefer to do it myself but don't want to...

Can some kind owner with an older MF, ideally a 35 (but a 100 series would probably do), with a front loader on, please let me have some details of the hydraulic hose routing from the diverter...

Can anybody tell me where I can get 2 hydraulic oil feeds from my MF35 to run a hydraulic log splitter fitted to the 3 point linkage. The log splitter has 2 feed pipes to its control lever valve...

Hi all. I've just started renovationg a front loader for my Massey Ferguson 35 (1964). The rams are quite corroded with patches of rust along their length. Can I just remove the rust with emery...

Hello folks, glad to join you. Been visiting this great site for years but now I have a quick question regarding my MF 35 with Continental gas engine. Tractor sputtered today like it was running...

I am a new member. I am considering buying a MF35 Diesel Deluxe tractor. Serial SNW250152. The pto will not disengage with engine idling with clutch down all the way down. Also to engage the pto...

Ust bought a 1963 MF 35 and it has no tach or evidence of ever having one. Anyone have any history on this? NR Eric owned a tractor with no tach.

Does anyone know the original color of the grill on a 1962 MF35 Deluxe? Mine is painted silver like the rear rims. Tractor has been repainted in the past, very poorly I might add. Any help greatly...

I am going to rebuild my Perkins Diesel. The serial number is CL 1856896 C. For some reason this number doesn't seem to want to cross over to a A3.152 Engine. Also, the injectors are straight up...

I am new here to the forums, but I have searched hi and low on the internet for some "how-to" info on this tractor and have come up short on a few things. At the moment I have no brakes on this...

I thought I would give these forums a go and see what help is available for a beginner like me. I got given this mf35 from a christian camp on the beach where it has been languising for several...

I'm looking to give my old 35 a rest and was looking at the 2605 as a replacement. Old faithful is great at pulling a small scraper, gill pulverizer, and small brillion seeder for small landscape...

Soon I will be locating and eventually purchasing a Massey 35/135/150 and thought it would be prudent to locate a source for OEM Owners/Service/Parts Manuals. I have seen a number of people refer...

Hi everyone, im a newbie to tractors but could do with some advise. I have a massey 35x of which i believe is standard. I have recently had my trailor taken away to be refurbished, so i have...

Hi guys, New problem with my old FE35. I was just out slashing, and noticed it sputted a bit, i thought ok, small fuel starvation. As i turned the corner, it sputted more and she stopped...

My MF35 Utility needs rear tires. I currently have Goodyear Industrial Sure-Grip 14.9x24 R4's, loaded with fluid and iron wheel weights. The tractor is used for mowing the field, moving snow...

I have a nice little MF35, that i use for moving bales and general smallholding duties. I have an old cable driven post knocker for it, and it is showing up some wear issues on the lift arms. the...

Can anybody give me some advice on how to get the dash off my MF35 to reach/replace the gauges (stupid question because I'm sure most of you can:laughing:)? I've got loose wires up under the...

I have a Massey Ferguson 35 older Model (60's) and it is stuck in 2nd gear. I have always been able to get it unstuck before but this time I haven't in spite of trying everything I knew to do. Can...

Hello all. I'm new to the site and appreciate all help I can get when repairing my tractor. Thanks John

I have a 1962 Massey Ferguson MF 35 S/N SGW 226417. While searching parts catalog I found MF 35, 35 Special and 35 Deluxe. What is the differences and how can I tell which one I have. It is Z134...

When we bought our farm I purchased a 35 Massey Deluxe. Used it to clean the place up. Bush Hogging hedge rows, moving logs, digging holes for trees, spreading fertilizer and lime at 4,800 hrs it...

I am looking at a Massey 35 for sale with a perkins diesel. Any one out there own one, and can give advice on what to look out for while I am checking it over? Thanks, Dave

I am planning on taking a drive to look at a Massey 35 diesel with a perkins diesel, new tires with rims sandblasted and sealed. Is there anything unique to Masseys that I should look out for...

I have a probably leaking diverter valve on a 35, as when its set to loader and the control is on 'up', the 3ph lifts first, then the loader lifts. If its set to external (ie tipper trailer) it...

For almost the same cost I have located three older tractors nearby. All are gas engines, the Deere and IH don't have working tachs so no real idea of the hours. The Massey has about 1800 hours on...

Hi guys, I need some help. I have lent my MF35 to my son, who had some issues with the tractor starting. He suspected bad/old battery so took out the battery from his V8 ute and put it in the...

I have a MF35 with a bad generator. Any thoughts on rebuilding the generator vs buying an alternator. If I go to the alternator I will need a kit to line the pulley up. Currently none of the...

Hi, I've got a petrol MF35 and its only running on 3 cyls. #3 cyl has no compression and I'm suspecting a burnt valve. A mate has offered a cylinder head from a TEA20. Does anyone know if this is...

I HAVE RECENTLY TAKEN OVER USING AND LOOKING AFTER A MF35. IT RUNS QUITE WELL BUT TODAY I NOTICED THAT OIL WAS COMING OUT OF AN OVERFLOW PIPE THAT RUNS FROM TOP OF ENGINE, ANT IDEAS WHATS GOING ON...

I HAVE RECENTLY TAKEN OVER USING AND LOOKING AFTER A MF35. IT RUNS QUITE WELL BUT TODAY I NOTICED THAT OIL WAS COMING OUT OF AN OVERFLOW PIPE THAT RUNS FROM TOP OF ENGINE, ANT IDEAS WHATS GOING ON...

Hi,I have a mf35 with z134 gas engine,I just bought this tractor I have a problem with power. It runs good but when I drive it and start going up a small hill it try,s to stall. If i give it more...

Hey guys I do not think my Gen is working. I'm not familiar w/ Gen.s so what should I see as output? between what? I assume there is a voltage regulator(I see what looks to be one on the left...

Hi - a neighbour has asked me to help make him a copy of an original massey 35 counterbalance weight for his '35 There is some discussion about it being off centre, and sloped so that it 'locks'...

Hi, I got a massey ferguson 35 wiring harness (loom) from sparex, but the colours don't correspond with the manual colour coding. Can anyone help, please.

Hey yall, Just picked up my first tractor the other night, a 1960 MF35 with the perkins diesel. Runs like a swiss watch. However the trans case fluid is white-grey, meaning its got water in it...

I bought a 1962 Massey 35 this past summer that has a crack in the manifold. I purchased a new one that arrived today but I've been worrying for days about "what if...". What if I try to take...

My old 1960 MF35 started up well enough in the cold, but it wouldn't rev up. I gave it more throttle but it wouldn't accelerate. Soon I noticed a cloud of dark smoke behind. It didn't improve...

Hello everyone, I have massey 35 running a perkins disiel engine. The fuel is going into one side of the pump and not coming out the other I think the fuel cut off is playing up does anyone know...

New member here ...im looking for information regarding a Massey 35 utility. it has the forward reverse shuttle shift and im wondering if this tractor could be converted to live p.t.o. ? Is it a...

Hi All, Been doing alot of searching for understanding what is on the CD that pertains to the MF35 (specifically the Perkins Diesel). Does anyone have it and do they believe the amount of...

I've got water in the tranny/hydraulic fluid again after putting out $140 for a new round of permatran. I figure it's due to residual left over fluid in the tranny/pump. The change I did, I...

I'm trying to understand, I believe this is a diverter valve, but looking for confirmation. Since this picture has been taken, the seals have broken down and it no longer functions. It's leaking...

MF-35 (FE-35) parked until I figure this out. - TractorByNet.com Thanks, I have suspicions that this is the filler hole, but I would appreciate confirmation. Also, I'm asking a hydraulic...

Hi All, I'm looking at picking up a 1958 Massey Ferguson 35 which, according to the Serial number (SNM) is a Perkins Diesel w/ Two-stage clutch. What comes with it is a Bush Hog SQ60 and a...

So heres one I cant quite figure out. When I try to start my Massey 35 it doesnt turn over and I hear a fast clicking sound (like a relay opening and closing) down in the "electronic" of the...

Will be doing a R&R on the rad in my MF35. How difficult is the job? What I see is 2 nuts on the bottom, a support rod with a cotter pin up top, and that's all. Does the hood need to be removed to...

The hydraulic arms on my 35 will not go down? sometimes when I haven't run it for a while it operate the way it should and then it will bottom out at the top and will not go down unless it sets...

I've got a Massey 35 (3 cylinder) that is hard to start, bogs down easily and exhaust huge amounts of black smoke. From what I've been able to glean in research, this is likely and fuel/air issue...

: confused:Hope it's ok to post Ferguson questions here! I thought I bought a Massey 35 ,I'm getting older:confused 2: ,through out wheeling and dealing to be honest I didn't see it till today...

I recently traded my '60 MF35 diesel in on an '88 MF240. The dealer gave me $2400 and the only issue my MF35 had was a leaking injector pump. Did I get a fair trade value? I owned the MF 35 for 12...

hello everyone, I am considering replacing my 1963 MF 35 Special with Davis Loader. Current tractor has power steering, live PTO,loader, I live on 10 acres in SW ohio that is mixed with...

I need some help with a charging problem on my 62 MF35 3cly diesel. It has a new VR (Delco 1118981) , new battery(neg ground) and wiring harness. I've had the genny (Delco 1100383) checked and it...

Anyone have any experience/knowledge about these tractors? How much they may be worth? It is a gas engine model in decent shape with good tires and average hours. Has been barn kept. Thanks alot...

Hi I need to remove the old hand crank pulley on my MF35, is it just a matter of pulling it off or does the bit in the center that you put the hand crank into undo? There's no bolt holes in the...

my mf35 gas tank started leaking. cheapest I've found is $290 delivered ! anybody know where reasonable priced tank is ? If not I quess I will try to epoxy it.

i bought a mf35 deluxe and would like to convert it to electronic ignition. any one have ideas/recomendations ?

I have a MF 35 1960 3 cyl perkins I totally rebuilt, started up and engine sounds great. I am getting blowby on all three combustion chamber caps. The old cap gaskets were circular, and the ones I...

I have a MF35 1960 perkins diesel I rebuilt. After startup I get power steering fluid coming out of the breather vent that is just behind the steering shaft and on top of the steering housing. I...

i have a massey 35 (1964) with power steering. steering fluid is leaking out of the left side pitman arm shaft. which seal needs to be replaced and how do i get the old one out. any advice...

The MF35 Deluxe is a diesel engine. I was having starting issues with it, I was told the battery cables were probably to light and possibly corroded. So I removed the cables and had new ones made...

I have ten acres of east Texas prairie and have need of a small tractor, mostly for mowing the property right now, but also for odd jobs like pulling out posts, using a box blade, maybe some light...

I've got an old MF 35 that usually runs well enough, but recently it sputters very badly as soon as I start it. It will stay running if I work the choke in and out, but if I let the choke back in...

Hello, I have a FEL on my MF35 and it works fine, but the TPH will not go down. Right now I have a backblade on it so there is plenty of weight. I read through some of the post. I was wondering if...

I'm wondering what this thing is worth. Your thoughts?

I own a 1961 MF35 tractor (Perkins Diesel, 3cyl). S/N SNM210856. The engine S/N appears to be GKN1523G. Does anyone know where I can find the system MF/Perkins used for the engine S/N on these...

I've got a 62 MF35 with the a3.152 diesel. I need to locate the correct tractormeter cable. My serial # is SNM 229613. All the cables I find listed are for tractors starting with a later serial...

I posted this in the MF section, but haven't gotten any feedback. I thought maybe I'd try here. I have a 35 with the Perkins Diesel. The tractor had a Bush Hog Loader attached when I bought it...

I have a 35 with the Perkins Diesel. The tractor had a Bush Hog Loader attached when I bought it lasty winter. The loader seems quite capable on the tractor, but is somewhat slow for my liking...

massey 35 deluxe 3 cyl. perkins pouring oil out of weep hole under the clutch housing.I have already replaced the seals and o-rings on the transmission main shaft thinking that was where it was...

Not had my old Massey Ferguson 35 very long, and have used it so far mainly for pulling a water ballast roller and moving full size round bales with a rear spike and spikes on the FEL with the...

I use a 3 cylinder diesel MF35 to mainly move full size round bales, either on a 3 PT fork, or on the FEL bucket spikes, to drop them into a feeder ring. When the FEL is in use I have the original...

I want to buy a topper fro my MF35. It will have to deal with some scrub and brambles in woodland, and general grass topping, mainly on a 3/4 mile grass walkway I share with a neighbour. The deal...

Ok guys this sounds crazy but here goes tractor died one day while digging post holes acted like it ran out of gas. nope, managed to get it started a couple of times but didn稚 run long. this is...

Hi, new here, and to tractors in genearl. I am in the UK, with a beautifully restored MF35, looking to bore or knock some posts for a corral. I know you can run a PTO driven geared borer off the...

Is there any way for a little MF35's on board hydraulics to run a hydraulic type post hole borer if I mounted one on the front loader arms? Could you run an axillary pump off the PTO instead, just...

My brother is needing a tractor for a tree farm. He found a Massey 35, built in the 60's for around 3,000.00. He says it's in really good shape, but I haven't seen it yet. Any info anyone would...

As the title says, my MF35 cuts out after it warms up. When mowing at full throttle, it runs fine until the engine warms up. After that, it will hit and miss. That is, runs up to full RPM, then...

I have a 1961 MF 35 Deluxe tractor with a bush hog on it. It looks rough, but runs good. I purchased it as a package deal when we bought the land. I would like to sell now. Would someone...

I am still tryin to get it to loadup

Hello, I have been spending a bit of time at the electric fence. I just bought a 1964 MF35 Turf Special, Can anyone tell me about this tractor? WHat is the difference between the Continental...

I just purchased a poultry farm in NC and it came with a MF Deluxe 35. I spoke with a MF dealer and gave them the serial # and it came back to a 1961 Model 35 Deluxe, what is the difference...

I am trying to design how to mount a snowplow that I have from an Oliver tractor to a Massey Ferguson MF35 tractor. The Oliver had a solid frame which mounted under the tractor but which cannot...

I am looking at either building or modifying a loader to fit on a MF35 (no power steering). I have a few questions: 1) I have seen some with a pump running on a long shaft running in line with...

i posted this on the massey-ferguson forum a day or two ago and have no replies, then i found you guys... maybe this would be a better place, as this IS a 1965 model... i've limited mechanical...

i've limited mechanical experience and abilities... i find its usually more inexpensive to hire someone to do my fix'em up work than me try it, screw it up, and then have to hire someone to...

I am in desperate need of the wiring diagram for a MF35 Deluxe Diesel. Is there anyone that can help me out?

Tractor runs for about 5 minutes and then quits, starts after a couple minutes, runs for couple minutes, then quits. Gas filter is not plugged.Any idea what's wrong?

My Massey MF35 diesel is yellow, could it be an industrial version? It has a loader, 3 point hitch and a PTO. Thanks, Steve.

MF35 - gas - good operational condition but would like to add hydraulics to power some accessories. Most of current use involves a box blade and field mower. I like the tractor size and weight...

I am wanting to add a loader to a MF35 Special. Not sure at this point if it is better to look around for one (been watching ebay for about 3 months) or just build it. In the buildit category...

I have acquired a MF35 (gas) from my wife's grandfather. He purchased it new so it has been in her family since new. Anyhow, I am using it with a bush hog and a box blade. It seems to handle...

Does anyone know what the correct fluid type is for an MF35? Does it use the straight mineral oil the TO-20 does, or does it take the "universal" type?

Dad\'s MF35 needs hydraulic help! My Dad's MF35 has been having some problems (he uses it to brush hog his fields). He says after he cuts for a while the hydraulics won't lift the deck anymore...

MF35 stuck in reverse..shift will not move...been advised to push on fork (through transmission fill hole) with screw driver or small crow bar. What part fork & in what direction do I push? Does...

Fellow TBNrs I am looking for one of the above model tractors. My wish list, after extensive research is a 3 cyl Perkins diesel, 6 Speed Transmission, Two Stage clutch and Power Steering...