kubota b6100

I’ll need to replace mine, I didn’t realize that the foam was covering up so much rust down in the seat pan and so now it’s almost beyond a feasible repair. It’s been a great tractor and I’d like to find an original used seat in decent condition at a fair price if possible. Maybe someone here...

Tracter started up fine for months. I have been using jumpbox because to cheap to buy battery but in 2 seconds it turns right over strong starter. Today hookedup jump box and it beeps as if it's connected wrong which I know its not. Bad ground maybe?

I was running my B6100D I turned the engine off but I left the key on. About an hour later I realized the key was still on so I tri to start it and it just cranked but it wouldn’t start I sprayed starting fluid in the air cleaner and was able to get it started. My question is what happens when...

I have a B6100D I bought it in January the right brake did not work I took it apart and found the bull pinion shaft was snapped off on the brake drum spline I rebuilt the axle case with new bearings and seals bought a used bull pinion shaft from Agparts it looks like the shoes on that side are...

I’m wondering if this thing is like many older cars in that if I disconnect battery and it dies that generally means alt is no good? Won’t hold a charge, fairly new Wally World batter ( about 3 years old with a 5 yr warranty) Anyone change an alt in one of these? I have very little experience...

I'm been running the Green colors for years, and I need a smaller older sub-compact tractor to use on the 20 acres. My John Deere dealer has a 1979 Kubota B6100 HST for $1000.00. It appears in a normal condition for the 41 years it's been around. The dealer doesn't mention the hours on...

Hi all, I've had our Kubota B6100DT since 1993 (bought used) and it has proven to be a reliable workhorse. I recall changing the fan belt in the early years of ownership and *think* that I did it without pulling the radiator. Time has come to change it once again (likely should have been a few...

I recently purchased a B6100 with a 4ft mover deck. I am looking for available attachments for this tractor. I am from Southeastern Ohio. Please message me any information

I need to rebuild a lift cylinder on my loader on a B6100 tractor. Local dealer says that until I can give him a model number for loader he cannot help me getting a rebuild kit. I have cleaned it, search high and low but find no indication of what model it is. If someone recognizes this loader...

I have factory wheel weights, they are held on with incorrect hardware, makes it difficult to remove as Im assuming the original hardware was a carriage bolt of some type, Ive asked at the dealer, they were not able to find a part number, can anyone offer a suggestion? A standard carriage bolt...

Hey there, my B6100 has a leak in one of the rear tires. They are pretty badly dry rotted so I guess I've got my usage out of them. It has 29x12.00-15 turfs back there which I like as they are gentle on my not so hearty lawn. I don't see many options for this tire size but do see some...

I Am thinking about getting this B6100 4x4 that I found. What is a reasonable price. I know that depends on a lot. Im going to look at it tomorrow. As far as I have been told. Everything works, motor runs good and doesn稚 smoke, 1600hrs, new tires and battery. They had it listed at $4000 and keep...

Dealer wants 25 a gallon for the utd Operators manual says if need be I can use sae 80 weight. What's your opinions?

Hello, I just picked up the tractor last night, Ive done a search on this forum to read any prior posts but search function as Im using it dosent seem to filter my specific tracor. I know nothing about tractors, never owned one. Are these good tractors? How do they rank when compared to the...

hi i have had this tracator for 2 years now and when i have got an attachment on the back the hydraulics sink thank you sam

I have a 2 acre property with only 2 large trees and one barn, with a rather long driveway (slight incline, 200 ft). I had an deere la145 with front blower for removing snow, and mid mount mower for mowing. I also haul 12 cord of wood to my house with it every year. Needless to say, tractor...

I acquired this tractor about a week ago for $800. This is my first tractor. She's not pretty but runs good once you get it started. It has 4x4, 3 speed, hydraulic blade on the front, missing the three point hitch. I have started it and ran it several times using ether. It runs about 2mph...

Tractor was idling while I was standing next to it, and it just turned off. And now won't even crank. Lights work, oil light works, glow plug indicator works... But not even a click when the key is turned. Trying to start with clutch disengaged, pto in neutral, diff pedal is disengaged. I did...

So this tiller came with a B6100 I just bought It appears to use a different top bracket instead of the standard top 3 pt arm Also, the female end coming out of the tiller is really short and appears smaller than the male PTO shaft on the tractor In measuring the connection I need is only 12...

Have a chance to see a tractor Sat morning, but they are two hours in different directions 1. 1983 ish B7100 w/ tiller FEL and mower 4x4 with 2000 hours $7,000 obo 2. 1981 B6100 w/ FEL, scraper box, and backhoe no clue on hours $6,000 Any advice? backhoe sounds like fun but I really need...

My B6100 came with a set of aftermarket 3-point hitch lower arms. From photos I've seen they look to be shorter that what the tractor originally came with. Anything I put on the back never seems to fit quite right and I was considering making a new set of arms. Can someone tell me the...

Good morning Heading out in a few days to take a look at a B6100 4wd with 40" tiller and FEL 1400 hours Mainly run across positive things about this model, seems to be about the right size for my 2 acres of gardening and cleaning up Was also looking at Yanmar 1500s Anything to look out for...

Hi all, I'm new to this forum but not new to working on equipment. If I can help I'll be happy to try.

Hi all, I'm looking for some advise. Looking to buy my first real tractor and am struggling with a choice. What I'm looking for: The main requirement for me is snowblowing in the winter, my driveway has a steep incline to get on to the street... without measuring I'm guessing around 20-23...

my historically reliable B6100 wont even crank. Glow plug light goes on, clutch is depressed and battery is fully charged but it wont even turn over. Help....

I am looking to buy a B6100 but it seems to have a transmission problem. It is stuck in 1st gear. Actually, I believe it will shift between 1st and reverse, just not the higher gears. The owner claims it was working fine until he parked it (claims for 3 months.....), now it is stuck. It will...

I talked to a guy that has a B6100 HST that "needs a motor" He said his friend put gas in it instead of diesel and now it needs a "rebuild" I'm kind of hesitant buying a tractor that doesn't run, what would a project like his be worth assuming that I will be doing the work myself?

Kubota part # 70080-00338 clutch assy-magnetic is discontinued , are there any kits or can these clutches be rebuilt magnet is good needs friction plates. Operates belt to the belly pan

New member thanks for the addition

Hello one and all, My issus is with a B6100 that wont allow the glow-plug light to shine. Are these replaceable? and is there a method one is able to test it? Thank you.

I am having trouble with the 1978 Kubota B6100 that was just rebuilt. I did a complete overhaul on the motor, and after running it for about 2 weeks this past winter, the rear main seal went on the engine, allowing engine oil to pour out of the starter when you ran the engine. From what I could...

Either mice or squirrels got to my B6100E, and chewed the wiring. I noticed bits of colored insulation on the footboard when I went to get on it today. Turned the key, and nothing! Anyone have a wiring diagram?

I recently completed the engine rebuild on my 1978 Kubota B6100 and have just barely been able to put it to work with snow removal (we've been getting pounded in the North East). It takes me a couple hours to clean my driveway with this little machine and this morning the tractor started...

Hi All, I have been posting info and pictures about a Kubota B6100 that I mounted a Kubota LA302 FEL on. I also rebuilt the engine on this one, but that really doesn't matter here. My problem is that the auxiliary hydraulics I plumbed in for the loader, and rear set of hydraulic couplers, are...

I recently replaced the head gasket on my B6100 HSTD. I checked for flatness and all looked good. I got it started, but now it has no power...it will go fine on a flat or down hill, but even the slightest uphill and it bogs down. It starts fine, idles fine at low or full throttle. Short of a...

I purchased a used Kubota LA302 FEL about a year ago and I finally have had time to work on mounting it on my Kubota B6100 tractor from 1978. The vertical bracket plates and rear axle mounting plates were cut out about a year ago, and just this fall I'm having time to get everything mounted up...

Good evening, this is my first post on this forum. I have here a B6100 that was working great until today. Stopped for a fuel break then when I fired back up the 3ph would not raise. The handle will not go in the lift position. It moves forward and clicks, but thats it. Fluids are find. It feels...

I am replacing the head gasket on my B6100. I found a small leak on the intake manifold side. I got the head off (a previous owner had snapped the head off of one of the bolts on so it took a little work to get that one out!) Any suggestions as to how to remove the carbon from the head before...

The port closest to the driver on my injector pump does not squirt fuel. Any suggestions?

I am looking for a front end loader for my Kubota B6100 3-cyl diesel tractor. It came with a plow attachment which is of limited use to me. Apparently Kubota no longer makes a loader attachment for that tractor any more, so I am searching for a used one ( or a parts tractor with a loader which I...

Servised tranny after water had intered through shifter - flushed and refilled tranny started tractor and 3 point wouldnt work. found lever had slipped out of control valve. Went over motions and remember pulling up on 3 point assembly. WHAT HAPPENED AND HOW DO I FIX IT.

I have a 1978 Kubota B6100 Manual shift 4x4 model and I've been trying to hunt down R4 tires and new wheels. Someone posted info about a B6100 rebuild back in 2006, but I have not been able to get in touch with him, even after several attempts. My machine currently has almost worn out turf...

Hello All, I'm brand new to the forum and I thank you for taking the time to help me out! I have a 1984 B6100 HST w/ a Woods FEL. I have an opportunity to pick-up a Kubota L4520 Backhoe attachement. I have measured everything up and am very confident (with very slight mods.) it will hook right...

Hello, I operate a Kubota B6100 for my Mother on her hillside property. While warming up the engine a couple of days ago, I heard a high pitched wining sound from under my seat where the gear box is. The unit was running fine and did up until I shut it down. I checked the gear oil's dip stick...

Just changed the oil in a new to me B6100, went to tractor data and it said 4.1 qts, chahged the filter and poured in a gallon, checked the oil level and it is way above full, is this the proper amount for this tractor.

and it came with no operator instructions. My first of what may be many questions to the members of the forum is : What are the proper steps to follow in order to simply start the Kubota B6100hst ? I want to make sure I dont hurt the tractor by some mistake. Also what in your opinon is the best...

I have a B6100 and since becoming the owner (3 years ago) I've noticed that the 3-pt lift falls slowly. Sometimes more than slowly. Does that sound more like the valve, or the lift cylinder? How much headache for a novice Kubota repair person?

I have a Kubota B6100 HST-D That I recently attached a 4-foot rear mount mower. The tractor runs fine, however, when I try to mow up hill, she really struggles. I have a 5' brushog (that I know is too big for this tractor) and we can cut light stuff up hill and down all day just fine....it...

I have just bougt Kubota B6100. It has 920h on it. Looks in pretty good condition. Cold starting has some delay and couple of tries but otherwise looks clean and no rust. Attachments include: mover, plaw, front blade and some sort of tiller with disks but no Power attachment to it. I paid $3800...

Ive been reading on here for sometime now and have decided my seal is out(hydrolic pump). hydrolic fluid in crankcase, blows dipstick...bla bla. Read where that 9 times out of 10 the pump is gonna be bad . change the seal and its the pump lose all fluids and seal again. Ive found a pump for...

Can anyone tell me what thread size the hydraulic port, with the handle, under the seat is? I'm assuming it's metric? It leaks when the revs are high, so I'd like to get a plug for it until I can fix the valve when I overhaul it in the winter. Thanks, Jim

found a Kubota B6100 2wd with a three cyclinder diesel, three point hitch, and pto. he is asking 2,100 and im wondering if thats a good deal. thanks

Can anyone tell me what thread size the hydraulic port, with the handle, under the seat is? It leaks when the revs are high, so I'd like to get a plug for it until I can fix the valve. P.S. The port, with the handle, under the seat reminds me of the booth, in the back, in the corner, in...

Hi there, I have a Kubota B6100HST that I use mainly for cutting grass with a belly mower. Last fall, the last couple of times I cut the grass the low oil pressure light came on after it had been working for a while (1/2 hour or so). Not sure what the problem may be. Anyone have any...

Have a fuel overflow pipe (hose) coming off of nozzle #2 , that is dripping during operation! End of tube is just above the fuel filter. Is this normal and should this tube connect to somewhere special? Had a clutch put in some time back and have found MANY things not reconnected...

Can someone be so kind as to tell me what side of this bearing should be against the clutch plate? I can not seem to find this anywhere. Thanks

I just bought the little tractor and it runs nicely. There is one problem, however, with the front axle pivot assembly. It appears to me that the differential/axle assembly should only rock side to side, however, when the steering wheel is turned, the differential/axle assembly appears to move...

Hello to all. I have been reading through the 1000 plus pages on this forum and absorbing as much of the unlimited info as possible. I recently picked up an older B6100 4wd with around 2100 hrs on it. Great little tractor. I have replaced the rear hubs with the newer style, changed out all the...

I am having a problem with my Kubota B6100D. When I first start it everything seems OK. I can raise and lower the back blade with no apparent issues. I can shift and move the tractor with no apparent issues. But, when I raise the front bucket to dump is when transmission fluid starts leaking...

I am looking to replace the worn out OEM 6 - 12 Bridgestone Farm Service "Lug W" front tires on my B6100D 4x4. Can anyone tell me the Diameter and Rolling Circumference of the OEM tires. The rears are in good shape so what ever I get will have to be as close to the originals as possible so as...

I need this like I need a hole in my head, but I think it's too good to pass up. Can someone talk me out of it? I found a B6100 HSD with 1,200 hours on it for $2,000.00. Other than a rip in the seat, it's clean and all original. No implements go with it. What is something like this worth...

I have tried for four days now to get the split drive link off of my tractor. I got it used and I have never taken it off until now. The tiller came off fine and then I noticed that the drive link is in two sections...I can't get the one on the tractor PTO off. Can some one tell me step by...

So I'm think of bidding on this tractor (Kubota b6100E 2wheel drive). I need it for mowing 1 acer, garden and collecting firewood. What's the good and the bad? What kind of price am I looking toured.

Does anyone know if there is a universal company/supplier with rims that would fit a B6100D? I'm looking to put Carlisle Multi-trac C/S tires on it. Here are two plans. OEM --- Carlisle F 20.5x8.00-10 20x10.00-10 (Rim 10"D x 8.0"W 4x4" 2.5" pilot) R 27.0x8.50-15...

Does anyone run a 4-foot King Kutter or Howse brush cutter with a B6100? I need to mow ~2 foot tall weeds and grass on slopes.

I have a 1985 B6100HST 2wd Kubota with a 48 inch 3 blade belly mower. I want to buy a brush cutter for this tractor. The manual says that it is only a 14hp motor and recommends a 42 inch (300lb) single blade rotary mower. It handles the belly mower fine. Will it handle a 48 inch brush cutter...

Hey guys, awesome site/great info. Wondering if the B6100 (2wd) I have stands a chance at successfully plowing snow for me this winter (500ft of gravel drive, pretty flat- but it is central MI and we can get dumped on). Tried it with a backblade with very limited success. So after reading...

My new to me tractor has a set of extra hydraulic ports and a knob to switch from the 3ph and whatever is plugged in. What good is this? Something stationary like a log splitter or something where the 3ph does not need to move? I thought I might be able to run a hydraulic top cylinder on the...

I have a kubota B6100 with a d650-A engine. the engine has over 6500 hrs on it and i rely on the tractor daily. I am trying to find a rebuilt engine, or one with low hours that could, if need be serve as a direct fit replacement for the current engine. I was wondering if the D750, or any other...

New here, I just purchased a B6100E and after searching through old posts still have a question about using a 3000 lbs atv winch on the tractor. It is 23 amp no line pull load up to 160 amp at 3000# line pull. I already own it and it is in a 2" receiver mount. I am trying to figure out if...

Hello, been lurking a while researching and new to tractors and Kubotas. Tired of killing cheap used riding mowers by mowing thick grass and hauling around a pond; so set out to find a small used tractor. It is real clean, kept in a garage most of its life. I need to build a little shed roof...

hi guys, hope your thanksgiving is lookin good. i need to know if a belly mower off a B6100 will fit my L1501 tractor, they both have front pto so i'm hoping so, i got a lead on a mower for 60 bucks and i kinda hate to pass it up.:thumbsup:

I am in austin texas and any and all advice on getting an aftermarket loader will be appreciated.

My good ole B6100 battery finally died. I can't find any identifying info on it. Anyone know what size/class battery fits a B6100D?

Variable prices area to area, what do you figure a B6100 with 1400 hours, solid shape, very well kept up, with solid belly mower is worth? One may come along here, just wonder if it is a good purchase or one to lay low on. It's 4WD, tractor tires in good shape, excellent tinwork, a well...

Is a 48" belly mount mower for the 6100 likely to do a good job of mowing a lawn? My Gravely 50" is excellent, but since I am getting a 6100 soon, I'm wondering if the cutting job will be top shelf. Otherwise, why bother?

Transmission Growls very loud when clutch is engaged! Not so much @ low idle and not constant??? Thank's Steve.

I have a B6100D and have had problems with keeping the battery charged. In the past year, I've gone through 2 batteries and am unable to start the tractor without a battery charger. The fan belt is the appropriate tightness and I suspect that the alternator is the culprit. I am looking for...

Has anyone ever solved the on-going problem of connecting a hydraulic pump to the front PTO of a Kubota B6100D. I have read a lot of complaints about the odd sized 18mm 22 tooth spline, but so far I have heard of no real solution, other than being lucky enough to come across the original Kubota...

I am searching for B6100 rear wheel rims that accept 7-16 Ag tires. They are apparently not Kubota standard spare parts. The Billings, MT Kubota dealer found in an old manual that they were "locally available." No, they're not! Can anyone give me a lead? Thanks in advance.

I have a B6100 Kubota. It is an older model and Im not quite sure of the year. It is a gear drive. The clutch very touchy. Every time I let off it jerks no matter how slow or fast I let off. The petal seems to be adjusted correctly. Does anyone know if I can adjust the sensitivity.

Just about done and ready to mount the loader on the new refurb B6100:thumbsup::cool::thumbsup: Before [/IMG] After[/IMG] Been a fun and challenging build.

Hi, I've been reading other posts. The clutch release got lower and lower on the pedal. Today I adjusted it and within a half hour the clutch will no longer disengage. I'm guessing from what I have read so far that its likely one of the pressure plate fingers has failed. Anyone got any other...

I just took in this B6100 as a partial trade towards a Bobcat I had for sale. I had the Bobcat up for sale with no hits for months. I got most of my asking price in cash (good thing) plus this little tractor. I have no need for it really, did not plan to own a tractor, but it may be nice to keep...

My 26 year old B6100E has always been stored in a metal shed of the same age. The shed roof rusted, however, and before I realized it, rain leaked on several parts of the hood and fender and caused the finish to fade in those areas. I suppose the rain water stayed on the finish for some time...

I have a B6100 I need to attach a hydrualic pump to the front PTO which is connected to the crankshaft via a shaft/crank pulley adapter. Looking for correct part number shaft/crank pulley adapter/electric PTO. These parts ARE supposed to be available from Kubota as I am told but no one can...

Does anyone know how the fuel pump comes off a B6100? I'm trying to install a block heater and I need to remove the fuel pump to get the pipe installed. Picture from the parts catalog attached.

Hey everyone I am new to this and the tractor scene. I just recently bought a Kubota b6100 4x4 Manual tranny. It came with 3 attachments. It came with a 48" belly mower a 50" finishing mower wich runs off the pto and a snow thrower that hooks up to the front of the machine. So far it seems to...

I am going to add a hydraulic snow plow to my B6100. Is it correct to tap into the port under the seat (picture attached)? I know where to return the fluid, in the fill port. My question is, my machine doesn't have a valve on the plate containing what I am assuming is the pressure port. Will...

I purchased a B6100E. Runs great. The lifting hitch arms will not spread far enough apart to attach category one implements. The arms hit the tire. I assumed the tractor was made for category zero implements. A friend told me that is not so, though he could not explain why the arms won't spread...

After mowing today with Dad's B7200HST equipped with a 60" belly mower, I forgot how nice a mid mount mower is! It looks as though my B6100E was equipped with a MMM at one point. There are several brackets and rods on the bottom, a large bracket in the rear that sits between the two rear...

I have been offered a B6100 Kubota tractor at no cost. Just come and pick it up. It has some problems and I would like to know if it would be worth the trouble to consider making repairs. 1) The engine was blowing blue smoke-Heavy. 2) It overheated and lost all coolant splitting the coolant...

So I'm back on this task again and I'd appreciate any help you can offer. I have some new info though. The problem is that the battery doesn't charge and the lights and horn does not work. When I connect jumper cables to my car everything works fine. 1) When I take the battery out of the...

I have a Kubota B6100 that has descided not to start. It cranks ok it has fuel and the glow plugs are working. It started first spin yesterday after not being started for a couple of months. I used it for an hours or so with no problems. Now it just blows black smoke, trys to go but won't. I've...

Has anyone out there had this problem. My friend has an older Kubota B6100E 2WD. He recently whupped the PTO gears, tearing all the teeth off the 17 tooth gear. He ordered new ones from Kubota and they are real beautiful, fit on the spline just fine; but are too thick and cannot get the snap...

I am new to the site, and failed to read the rule about posting questions in the new member section. So this is a repost, sorry. I have been doing allot of research in my quest for a good used tractor. I have about 1 1/2 acres, but also have to help maintain a small road for 5 neighbors...

Sorry, I posted a question before reading the rules on new member questions here. I have re-posed my question in the Kubota information for form.

Have I been had? I just bought a tractor and it has a metal tag which clearly shows B6100D, but the number stamped into the frame shows B6001. Is this normal? Tractor sure looks like the tractor in the B6100 manual. Thanks, John

I have a b6100 non-hydro 4wd and the dynamo is not working. Mind you I'm not a mechanic so I'm doing my best. Basically the tractor lights and horn haven't worked in some time but did work a couple years ago. When I jump start the tractor and have the jumper cables hooked up the horn and...

Not sure if I am doing this right, so if you see my question more than once I'm sorry, I,m new. I need to know if a 4ft bush hog can be used on a Kubota B6100E. Need to know before I purchase.

I am possibly buying a Kubota B6100E and was wanting to know if it would be able to run a 4ft bush hog. Has anyone tried a bush hog on this size tractor?

Theirs a older b6100 for sale with a loader and bachoe. Would those attatchments fit my newer style ( 6 lug front rims) b7100 hst? thanks

A couple weeks ago a friend and I replaced the clutch, pressure plate, and throwout bearing on my B6100. Admittedly I'm not the best mechanic, nor do I want to be, AND I didn't follow instructions to the Tee. After closer reading of the repair manual I realized we didn't set the finger height on...

I'm replacing the clutch, pressure plate, and throw out bearing on my recently purchased B6100. I bought a repair manual and in the directions they show this alignment tool and "thing" (tech term?) you use to adjust the fingers on the pressure plate. Does anyone have any idea where I can get...

Are B7100 and B6100 FEL's or BH's interchangeable? Or other models that might fit the B7100 - B7200? Are there differences between manual and HST mounted as well? I don't need one enough to justify buying a brand new one. I seem to come across some from time to time on 6100's or manual...

Hi guys, just finished adding power steering to my B. Running it off the PB of the FEL. I removed the hose that went from the PB back to the block which sends it to the 3PH. I then put the power steering setup inline. The only issue I noticed is that when using full loader, the loader gets...

I'm new to the forum. Just picked up a '79 B6100E with 48" belly mower. It was setup with the front snowcaster when I got it. Time to put the mower on and I'm struggling. IT's the style with the 2 chains, belt driven from front clutch assembly. 2 rear wheels on deck. Anyone have pictures...

Hello everyone! I have been looking around this forum and figured I would join to get some help. I am looking at buying my first tractor. I have a chance to pick up a B6100 4x4 with 1050 hours, AG tires, 48" front mount snow blower with what looks to be hydraulic chute controls, full cab...

HI ALL, Just wondering if you can put the front blade from a B6100E onto a B7100HSD. The model number on the blade is KUFD110??? Any info would be greatly appreciated! Thanks, DDL

I have a B6100E with a front hydraulic snow blade with ag tires, 2WD. Model number of the blade is KUFD 110. I would like to put it on a B7100HST 4WD. Does anyone know if the blade will fit the 7100 or do I have to get a different model number blade?

I'm having difficulty getting on/off and operating clutch on my B6100 (handicap issue). Found a really nice B7300HSD w/loader for a good price. The B6100 has been a very good machine, any thoughts on the B7300? Thanks

I have an older B6100 HST that has been a real work horse. It used to take about 3 seconds for the glow plug to heat. In the last two weeks it went to 6 seconds, then 8 and now the tractor won't start. I'm not real familar with these small diesel engines, but I'm guessing I have a glow plug...

I found a kubota b6100 with a bucket loader and backhoe on it. 4/wd. I am gonna go look at it tomarrow. IDK of a price what do you think is a fair price. I dont have any pics or anything. the tractor is at an auction. Let me know what you think.

So, I had the afternoon off work yesterday and one thing on the "to do" list this week was to finish mowing the yard. I took the three blades off my Sitrex SM-150, and used an angle grinder to "sharpen" them. Very crude, but they ended up with a pretty decent "edge". I put them back on, and...

I have an old B6100 that I bought used 2 years ago. This winter it started to get hard to shift and the clutch would not disengage completely. Then it stuck in forward. I pulled the top off of the gear box and the shift slid on the one shaft was tight. I honed that out and it now shifts fine but...

I have an opportunity to buy a Kubota advertised as a B6100 4WD with a 5' Bush Hog finishing mower for $3,200. The owner described it as 16 HP 3-cylinder gear (non-hydro) model and "very clean" with less than 500 hours. It has Ag tires and front weights. He claims it needs nothing, ready to...

I inherited a 1984 2 wheel drive Kubota B6100. It is at the local dealership getting serviced as it had been sitting for a few years. Dealer tells me the head is cracked, but doesn't know if it can be repaired or if a replacement can be found. Any suggestions on finding a new/used replacement...

Anyone have any tips on if this is a big job or a matter of remove and replace. I have the adjusters maxed out and still can't stop. Don't usualy go fast enough to get in trouble. But after all the repairs that have been done on this old beast to make it go forward. Might as well make it stop...

Today I was cleaning up the couple inches of snow we got with my recently made snow pusher attached to the Kubota bucket. It was going really well and I was enjoying the seat time. I was pushing a bank back when I tried to stop by pushing in the clutch pedal. I heard a clunk and it still kept...

Hi all, soon I will be putting my B6100 w/attachments up for sale and wanted to get some input for pricing. I am an Ebay addict so I have got some prelimenary numbers in my head but wanted some other input. The tractor runs great has been quite surprising to me for its size. It burns no oil...

I recently aquired a B6100E with a 60" finish cut mower. The old girl needed some cylinder head work and is in the process of re-assembly at the moment with all new top end gaskets. I want to add a water temperature and oil pressure gauge. I've located the oil pressure port, but can't seem to...

I have a b6100 kubota with a 3 cyl engine. I have the engine apart and need to know which is the top and bottom of the rings.I have a aftermarket manual but the rings picture isn't clear enough to make out. Thank you

Hello, Well we finally got our cold snap and our equipment is NOT liking it! Can anyone tell me what diameter the lower radiator hose is on a B6100? I'm needing to pick up a heater and haven't a clue what size it'll need. I wouldn't worry about it that much except the new Ford 860 DWARFS the...

I have to adjust the lifters on my D650A engine and am a bit confused. I removed the plug on the bell housing and turned the flywheel. On the plug hole of the housing there's a mark. On the flywheel I have 1|TC 1|FI 2|TC 2|FI 3|TC 3|FI . Could somebody tell me how to line up what...

Recently got a B6100DT, and the steering has a lot of "play" in it. Everything is working OK as far as I can tell. One guy told me that the bearings needed to be replaced. Another guy told me that every small Kubota has this same condition, nothing to worry about. How can I tell if this...

Been looking at a b6100 hydrostatic 2 wheel drive, turf, tires and mower. When I raised the deck, it seems like there was a loud gear clicking noise. the seller said I had just raised the lift to the upper end of travel. Is this normal on a b6100? There is a small handle under the seat...

Hello, I'm desperately in some need of advice. I asked a week or so if the B6100's were Catagory 1 or XB and I was assured that they were Cat 1. Now that we've made irreversible arrangements (sold the other tractor & spent much of the $$$) to go with the 6100 as our main tractor for awhile, I'm...

I just aquired a B6100E, 2 wheel drive, 3 sped manual tranny, with a 3 speed PTO, which I have listed in the classified for sale. I am not familiar with the 3 spd pto. What are the speeds for the PTO and any other things I might want to know before selling this tractor? I already have a Yanmar...

My B7100 engine trouble was worse then I thought. I put the project aside until I found a suitable parts tractor that had a good engine. I just found a guy in my area that is selling a B6100 HST. The pics look like my B7100. The guy is going to provide the engine model number tonight. My model...

Just bought a B6100DT 4x4 from a friend I trust. It's in good condition, everything working as far as I can tell, I'm new to this. Paid $4500, but along with the tractor I got a 48" bush hog-type mower, a flat blade (not hydraulic), a tilt scoop, a toothed box grader, a post hole digger with 2...

Hi guys, I was fortunate enough to win an auction for a B6100 and even though I haven't yet picked it up am looking at implements for it. The only thing is, I'm not sure if the B6100 is true Cat 1 or if it's the modified Cat 1 and I'll need to be getting the XB equipment. Can anyone tell me what...

Hello Folks, I have a B6100 ..... any words of wisdom on adjusting the clutch? Regards, Eric

Hello folks! Great forum!!! I have recently purchased a B6100 4x4 with 780 hrs .... works and looks pretty good for an antique! I have some basic questions as the manual that came with it didn't wear as well as the tractor. :rolleyes: The hydraulic fluid: where is the plug to check it? And...

I got a call from my local Kubota service manager this morning and now kind of feel like their has been a death in the family. I took the tractor in to have the low oil pressure light "on" problem diagnosed. The reply is that the pressure sending unit is okay and we cannot know more until we dig...

Had my front drive shaft universal at the differental end go out today. Anyone have any input on is this easy to replace? I have a loader on it so it is slighly hard to reach into the access hole. Wil I have to pull the front axle or can it slip into the front then re-attach the broken rear...

Hi everyone, This is my first post although I have been busy reading so much great information on this forum about my new(old) Kubota B6100D. Here goes- The rear PTO seal is leaking and I have a new one from the dealer. Can anyone provide any information on installing it? The 3 posts on...

owning-ML-895887-ML- Kubota specific thread.

Anyone know where I can get a good used transmission? It's a Kubota B6100, 4 wheel drive. No luck locally. Any advice will be helpful! Thanks.

buykubota-ML-885752-ML- Kubota specific thread.

i am looking for an approximate value of a Kubota B6100 o 7100 tractor w/ a loader attachment as well as a flail? approximately 2500 hours. any help or input you could provide would be helpful. thank you. please email: cityofhalsey@rtinet.com

I have a 1982 B6100 as stated in the title, and I need to do a clutch job on it. I've been searching for schematics or diagrams on the best way to accomplish the replacement. im debating on whether to split it, or remove the engine and acces it that way. If anyone has any advice, please help...

Hi first an intro first post here. We have a 7 acres hobby farm outside Williamsburg VA. Have some chickens goats on the way. Large garden mantained with my trusty 2554 Sabre. For the tougher stuff the newly aquired B6100 with loader comes in. Thats the one with the odd problem. I bought it...

owning-ML-792363-ML- Brand specific. Moved to Kubota Owning/Operating forum.

Hello, just posting a pitcure of my little tractor for someone who asked the size.

I need to remove the PTO drive shaft from the rear to replace the gear that turns the PTO shaft. Do I need to remove one of the side rear axle covers to complete this task. Thanks for any advice/comments! SB

I was wondering if anyone here would have the opening pressure specs for the injectors in my old Kubota. After 2250 hours, they could use a little attention. I plan on removing them and checking them, but is pointless without the specs, which brings me here. Thanks, fellas. ZackaryMac

owning-ML-754660-ML- Kubota specific post

Hello, I've browsed this forum and see it has lots of good info. I recently picked up a B6100 with FEL and TPH very cheap because it has a hydraulic issue. I haven't been able to dig in to the issue yet because of the constant rain here in NH but will soon. Anywhere I should start looking...

I have the opportunity to buy the subject tractor for about $3500. Has 900 hours, in good physical condition, needs tires. Will be my first tractor - any warnings, cautions or other advice? Does the price sound reasonable? How fast will it run in forward? How high can it cut?

Looking into a 4 WD Diesel Kubota B6100/disc, PTO, and about 600 hours (?), present owner thinks a 1983. Have seen this model on posts @ TBN, but some have "letters" following model number,...what do they signify?...what would be a fair market value for this tractor (in California)? is this...

The nice folks at tractorsmart.com informed me that there was a service bulliten on the broken pto case covers on the older b6100/7100 tractors. The fix is to replace the pto and 5th/reverse shafts and the two gears. A little pricy but better than buying a new tractor.

Hi, I have an older Kubota B6100 that has seems to lose lots of power once it warms up. The engine has even slowly idled down just yesterday when I had only mowed for about 30 minutes even though the thottle was still in full position. The hour meter shows 1500 hours and is in working...

Hi, Does anyone out there use a sickle bar mower on their B6100?

Does the B6100E have a rear axle lock. I'm wondering if it will pull a 4ft bushhog and tiller with out much trouble. Does 2800.00 sound like a good deal. It comes with a finishing mower and a disc thing. Thanks

I'm hooking up a 4' brush hog from an 8N tractor to a B6100E Kubota. Is the over-run coupler required or even necessary?

Hey folks: Looking for a little guidance. I'm considering picking up an older small Kubota. These all seem to go in around the $5K price range, give or take a bit. I'm looking for HST, 4WD, hoping to find one with a loader already installed, and would want to eventually run a small backhoe...

I recently acquired at B6100DT (4wd) that came with a finish mower and factory installed hydraulic front blade. I have determined that, while its a great little tractor at just under 1000 lbs with 14hp, I desire something a bit heavier and in the 20-25hp range. Therefore I have offered it...

I have a b6100 with a factory installed hydraulic front blade that has two levers...one to raise and lower and one to angle. There is no tilt control. I got to wondering if I could weld up some heavy steel stock into arms, weld up a crude bucket, and plumb it into my existing controller to...

4WD with factory hydraulic front blade and a finish mower on the back. One owner before (whom I know) who used it to mow and push snow/gravel. I'm afraid at 14hp it may be undersized for my needs/desires. Primarily I will use it to mow about 1.5 acres of pasture, grade 150 feet of gravel...

I own a 50 acre christmas tree farm I already have a kubota B6100HST I use it to mow my tree rows never had hardly any trouble with it. Went to the dealer to purchace a second and larger tractor to do the outside of rows work.JD and NH seemed to pricey for the machine verses the L3400.My L3400...

I broke the key of in my ignition switch, and I was just replacing it with a universal switch and a seperate glow plug button. Anyway, I had 5 terminals on the old switch: 1) Power in 2) Start 3) Run (hour meter, lights, horn) 4) Glow plug 5) ??????? It's a black wire with a white stripe, it...

I have aadded a snow blade to the front of my b6100 and would appreciate any advice on hooking up the hydraulics. The original controls for a blower in the front were tapped into the distribution block on the right side beside the motor. This arrangement seemed to create a bypass problem for...

Looking at a '79 B6100 with 4WD. Need to know the specs. on it. (ie: 3-pt capacity, loader capacity, weight...) Please let me know if their is a site with the info. on these older model tractors. Thanks in advance. -Eric

Got a lead on a 1979 Kubota B6100 4WD. I believe it would be a B6100DT. Has a front loader, backhoe, snowblower, and homemade 3-pt logsplitter. Tried it out and all seems great. Starts right up and runs without any problems. Seems to have 2000 HRS. The guy bought it new, so he knows all the work...

I've been looking at buying a tractor to maintain my land until I build a house. I found a '84 Kubota B6100 in some local classifieds. It looks to be in pretty good condition. I'm in the process of finding out how many hours it has on it and it's history. It comes with a rear blade and a...

I'm having trouble locating my hydraulic filter on my B6100E. The only place i think it might be is this large bolt on the side of the transmission. Does anyone know if this is it, or if it is located in a differant spot. My owners manual just shows me what the filter looks like when its out but...

Hello, My mower runs from a front electric pto since its a b6100E which is the 2wd gear model. It has no mid pto. Anyways my front pto started making a high pitched noise and just seized up....after shutting down the tractor i noticed the electric pto still spun freely when off...it is only...

Hi Could anyone tell me if the B6100 engine has a thermostat? I noticed the radiator and screen in front of it had lots of plant fuzz on them. On the same day I also changed the oil and filter. Later that day after cleaning the radiator I discovered the oil pressure light flickering while the...

Hi, I am a new B6100 Kubota owner. I am wondering if someone could tell me where the hydralic hoses attach to the tractor. I have the KUDF110 front blade but not the hoses. Thanks, Sony

Hey All, I'm hoping someone can tell me if there is anything about the B6100 (gear) that is better then the B1550HST. I'm familiar with the B6100, and it's adequate for what I'm doing (strip till and mowing on small vegetable farm). I'm looking for another machine for the same purpose and there...

A dealer has a 1979 B6100 4wd. with 1850 hours. Its in pretty good shape and everything seems to work. Vertical exhaust. Needs a paint job. They just installed new rear axle seals. They say it came from a nursery. It has some type of spinning hubs on the outside of the front axles. I thought it...

Ok, here's a couple (probably more ) questions for you knowledgable and willing participants : 1) below and just forward of the seat is a oval knob with an arrow on it (looks like a knob) and a cap just beside it. What is it for? Hyrdalics, per chance? If so, 3ph hydralics? 2) I understand this...

BG100E or B6100E A friend of mine has found this BG100E with a Back Hoe it is a 14 hp the man wants 4700.00 dollars year unknown at this time at least 5 years old was very small but would work grat in friends Horse barn. Any of you have any info on this tractor.

A fellow in my area is selling a B6100 with a 42 inch Woods deck. I haven't seen the tractor but here is what he told me about it: manual trans (dual range) 2 WD turf tires 18 HP 3 cyl. engine (the Kubota WEB page says 14 HP) He said it is 14 years old (when did they stop selling new B6100?)...

Anyone know about the B6100? I'm looking at the ad below for $4900. Is this a Grey Mkt or a unit suitable for use on a small acreage (10A)? "Kubota B6100 4x4 Diesel Tractor with loader, 3 point and rear blade."

I just purchased an ROPS from Kubota for my B6100HST and have an installation problem. The tractor has a mid-mount Kubota mower and the cables that raise the mower attach to linkage that is suspended from the top arms and attached to plates that are bolted onto each side of the PTO housing. The...

I just purchased an ROPS from Kubota for my B6100HST and have an installation problem. The tractor has a mid-mount Kubota mower and the cables that raise the mower attach to linkage that is suspended from the top arms and attached to plates that are bolted onto each side of the PTO housing...

Does anyone have experience with mounting a loader on a B6100? Can anyone suggest a source for a loader? Thanks

Newbie here! I have been lurking around for quite a while. I am going to look at a B6100e tomorrow. It doesn't have a hour meter and I don't know the year yet. It does have a Woods 48" mmm. This is one of the features I have to have. I will primarily be using it for grass cutting. I do...

What engines can be used as a direct replacement for a B6100. Kubota has D650, D750, D850, D905, D950, ... are any or all of these potential replacements for this tractor, even though they may have higher HP? Does any one have a low hour used engine, or a reasonably priced source for engine...

I hope I am not breaking any rules or showing horrible etiquette but since the classifieds are being worked on... I put a shop manual for Kubota B5100, B6100, and B7100's up for sale on ebay last night. If anyone is interested the auction runs through Sunday evening 4/21. I traded in my B7100...

It's a weird question, but then again, I'm a weird kind of guy. Had someone stop by the other day and offer me $6500 for my 1978 b6100dt with 50in FEL and 5ft back blade. 3000 hours, (hard hours), the only thing shiny on this tractor is the tiltmeter. Long story made short, I said no. Now...

I discovered this particular tractor (kubota B6100HST) on a JD lot and was hoping to get as much info on it before investigating further. My needs are for finish mowing and pasture mowing, snow removal. The use of ground engaging implements would also be nice. The BX2200 would be ideal for my...

where\'s mower drive on B6100D looking at a B6100D to buy, want to add a belly mower (woods makes one), says there is supposed to be an electric clutch drive pulley, but I can't find it?? any help?? anyone have a belly mower for sale??

according to the page of the owners manual kelvin sent me, the large belt that goes from the front pto to the mowing deck is an "A117"; well, it seems they don't make that size belt anymore; i can get an A116; i'm lookin for your best guess, will that inch shorter stop it from working?? it...

i am "considering" getting another set of tires and wheels for my B6100; it has turf tires on it now, which i like to mow with, but if the cost is not tooooo high, i'd like to be able to swap for traction. any suggestions/prices; has anyone done this?? heehaw

OK, i mowed my yard the other day with the 3pt "flail" mower, IN NOVEMBER; i guess it mows ok, but it made me decide to look into hooking up the belly mower; i put it on the tractor, and it raises an lowers ok, but, am i missing something about height adjustment, being able to go back to the...

I think Bob and Kelvin have B7100s and Bird used to so maybe you or someone else can help. The parking brake on my B6100DT is set with a little lever that engages a tab on the brake pedal in a toothed section of the lever. It's a 1/4" steel rod only about 4" long and sits on the deck down by...

We both show our age a bit, I'm afraid. The Kubota is 22, I'm older. Got the tractor from my Father in Law in September. Replaced the rear tires and added the ROPS. Now I'll turn to the cosmetics & give her a clean-up and new paint job. Bill

Hello..it's me again! I have a question, could a Kubota B6100DT support a Woods Dual (not dual as in two, dual as in "do-all") 850 backhoe? I know it is a bit large for such a small tractor, but it would only be used occasionally. Can anyone tell me if it would work? Thanks. TM

I appreiciate you all taking the time to answer my questions greatly! One of the biggest uses for this tractor would be using it with a flail mower. Does anyone know of a model of flail mower that will fit a B6100DT, and roughly how much it would cost? Also, roughly how much would a used...

I this out already, perfectly, but then my #$%&@*#!!!!! computer crashed, and I lost my message. I went and saw the tractor today -- it has 1980 hours on it, and it is dinged and dented up. However, it does have a hydraulic snow/landscaping plow with sufficient downward hydraulic pressure to...

Hello- I am considering buying a used B6100DT with a hydraulic snow plow (meaning the plow changes angle hydraulicly) for $3900. It's 4wd and DOESNT have a hydrostatic transmission, which really doesnt matter to me. What I want to know is this: 1. Is the PTO "reverse"? I know "normal" PTOs...

Does any one know where I can get a used air cleaner assembly for a B6100. I bought my tractor used and it had a make shift one, not original, on it. I have to would have to order it piece by piece from the dealer and it gets pretty expensive.

Anyone ever changed the rear pto seal? Mine was leaking, so I removed the pto housing cover to replace the seal. The old seal seemed to be bonded in to the metal housing cover. I had to take it out in pieces. Should the new one be bonded in place? The new seal seems to be too large to fit...

what in the heck is still whirling after i shut down the engine on my B6100; its not the fan, i can see that, but it "whirls" for several seconds after i shut-er down?? heehaw

my B6100D has grease fittings on what appears to be the gear box for each front wheel; is this the only lubrication, or is there also 90wt grease in each box?? i would also like to add a temp guage to the tractor, has anyone done this, if so, where did you install the sensor and the guage?? heehaw

i have a recently purchased 1985 B6100, with a belly-mower, a "flail" mower and a roto-tiller. i can't find the model number on the belly mower, and it wasn't mounted on the tractor when i bought it; does the belly mower mow well enough to go thru the trouble of mounting it to the tractor...

Hi, I'm getting a great "deal" on a 1979 B6100. I live in West Virginia and we have a house on 31/2 acres of ex-pasture land. My Father-in-law who lives in California said I can have his tractor if I "just come get it". Well, I may be dumb but I ain't stupid - I'm hitting the road in a couple...

I have a B6100E with a backhoe attachment that bolts to the frame. It appears to be original to the tractor since there is no 3 point hitch installed and the splines still have the original paint on them. I have 2 questions: 1. When lifting the main boom on the backhoe, there are times the...