Hey everybody. I have an 04 John Deere 2210 that has constant power with the key off. Also won't start and the dash lights turn on and off when I sit on the seat and stand up from the seat. Any...

Following my earlier note regarding play (a lot!) in the rear splined section of the driveshaft, I've bitten the bullet and gone ahead and extended the shaft by 18mm. The rear yoke is now fully...

So grateful for this forum! I have 3 tractors: JD4600, JD332, and the newest (to me), the JD2210, all Yanmar diesels. The 4600 and 332 both start on the first compression stroke and never skip...

I've got my 2210 apart again giving it a total clean and service (last was 2019 and over 200 hours ago). While I had the deck off I noticed I had some noticeable movement in the driveshaft when...

My 2003 JD 2210 with 151 hours was running fine and just stopped, then it would start but shut off within seconds. Now it turns over but does not start. I have done the following: - Blew out of...

I have yet to see any reports of issues with the parking brake on the 2210, so I guess I get to be the first. The plastic parts on JD tractors are a blessing and a curse. A blessing because...

JD2210. 62C mmm. 1100 hours. Been having this issue for a few years. Tractor runs perfect when not mowing. Just finished major service, fluids, filters, gear oil in mmm and all zerks greased with...

Anyone know of a sickle mower for cat 1 low hp tractor - 23hp. Thinking 5-6 foot max

500+ hours, cab, mid mount mower, FEL. Real nice shape. Prices on the net seem to be all over the place. Thanks Ryan

Lately my JD will run ok doing some shredding or belly hanger mowing. However, after about 15 minutes power starts falling off fortunately I can make it back to the shop when it stalls and will...

Hello everyone. Noticed oil leaking onto the rear rim right side, possibly on the left side too. But definitely the right side. 1089 hrs. Called JD dealer for quote to change a $6.00...

I got this Tractor as a barn find only 85 hours. It hasn’t been turned on in years. When I go to turn it on all it does is crank. I emptied all the fuel out of it and replaced it with new. Still...

I ran the 2210 VERY low on fuel because our local fuel delivery took quite a few days to get to me. Once they did, I fueled it up, along with all the other tractors, and drove it over to the...

I've got a JD2210 diesel ~500 hrs. I think the whole thing was made by Yanmar and they put JD green and logos on it. I was using it yesterday, moving things around with the bucket etc. I...

I have noticed that my 2210 will start rough if I start it at 1/4 throttle. It will misfire and puffs out a lot of diesel fumes for the first few seconds before cleaning up and running great...

Looks like some wire got wrapped around my axle and it tore the seal apart, so constantly filling hydro oil. Has anyone replaced the seal? Is the gasket just RTV sealant, or is there an actual...

Hi Guys! I have had a JD318 and then replaced that with the diesel 332 a few years ago. I have always done my mowing with these 300 series tractors and am happy with them. But I want a front...

My usual pass through the postings for the day on Craigslist landed me on a Curtis Cab for my JD 2210 only 1 hour away. Been looking, looking and even contemplated building one using purchased...

The rule of thumb is five horsepower per foot of rotary mower. With a 23 HP engine and 17.7 PTO hp I don't believe I'd go over four feet with that tractor. The tractor is also a bit light for...

So i think i put the loader on 'wrong' the last time i did it. I went today to take the loader off. I popped the front wheels up in the air, pulled the two front pins, and then pulled back on the...

So I pulled the snowplow off the 2210 today and installed the mid mount mower deck. Everything was going great until I pulled out the yellow pto knob and got a big nothing. The short version is...

Morning Gentlemen and Ladies. Since 2004 I have a JD 2201 SCUT which I absolutely love and it has done everything I've wanted to do and even more. However the other day I had the tractor up on a...

I own a John Deere 2210 with a Woods BH6000 backhoe and 2 of the 4 port relief valves are leaking. The 2 that leak are mounted on the upper part of the spool valve. One of the relief valves is...

My orig seat has totally come apart. Does anyone have any experience with a replacement they can share? Thx> Eric

Locating the zerk fittings on my JD 2210 drive shaft forward u joint has become difficult. I have posted pics that possibly someone can help me out. 3 of the pics are the u joint side away from...

JD 2210, Can I attach the loader with the quick hitch still installed? I think we are done with the snow for the most part. I would like to remove the snowblower and attach the loader now, but...

I am new to tractors and this site but I need help. My tech manual is on its way but while I am waiting: 1. Do I drive the sleeve onto the steering axle dry or use lube of any sort? 2. Do I...

Hello all, I need some help. I would like to buy a pair of wheel spacers 2"-2.5" for my JD2210. I am unable to locate the bolt spacing. I know it is 5 bolt but is 2.5" spacing correct. I know...

High everyone. A quick question. I bought wheel extenders for my JD2210 tractor and would like to use longer wheel lugs to secure them to the axle. I can not find the metric values. Is it a...

Hello all first time poster on this forum. As the title states I own a 2008 2210 with 700 hours on the clock. From the previous threads I've read prior to the purchase of this tractor a few years...

While awaiting spring I figured I'd look at what maintenance the compact tractor would need. It states @500 hours to do a valve adjustment and "check fuel injectors". The valve adjustment looks...

Bought used John Deere from dealer with 650 hours on it. Got it home drove it off the trailer and about 100 feet later, made loud noise when hydraulics were maxed out. Steering, or three point...

My jd 2210 tractor won't start. I've had the battery and starter tested by dealer, replaced the switch per their recommendation. The dash lights come on, but starter will not engage. What am I...

Hi All, I have a 2005 John Deere 2210 tractor that has developed a couple leaks and I'm looking for advice for the best way to repair them. The first leak, which is pretty significant, is...

Hello folks, first post, got an issue with the 4wd on my 2210, i have checked all the basics, not getting any power to drive shaft going to the front axle. Anybody have any experience with this...

Hello, I disassembled the tractor yesterday to have access to the drive shaft between the engine and trans. I have a bad ujoint and want to replace both ujoints while I have it appart. My current...

Hi everyone. Was using the tractor removing snow the other night, and noticed when I put the throttle up I was getting some vibration and a different sound like a fluttering sound. My son told...

After fixing a few issues with my new /used tractor I found a new one (sigh) One of the lift cylinders started leaking ...the Piston (shaft ? ) has some dings in it and most likely tore up the...

I have an issue right now. I have a 2005 JD 2210. Plowed some snow a few weeks ago then boom, the tractor died on me after using it for two hours, full tank. Went to turn the key and it only...

Looking to add a tooth bar to my 2210's FEL. Lots of options out there. What tooth bar have you added to your FEL and would you recommend it?

Does anyone have any good pictures they can share with the the zerks for the driveshaft on the 2210? Just bought a new to me 2210 and have greased all the zerks I can see, replaced all filters...

Not posted for some time... tractor has been behaving itself. Nevertheless after 13 years one of the rear tires (carlisle 26-12-12) has started to crack and needs replacing. I was going to take...

I bought a Deere 2210 with the intention of putting a loader on it. The older 210 and 200CX are out of stock. I found on the H130 manual online mentions the 2210 as compatible. But when I...

I recently acquired a John Deere 2210 tractor with a 62C mowing deck. But the lift rod is missing and I would like to know if anyone has one of these tractors and a mid mounted deck that can take...

2210 jd will not start blows 20 amp fuse when key is in the run position must be a short where to start Thanks

I have a John Deere 2210 tractor that I bought in 2005 with a 62C Mid-Mount Mower. I would like to use the mower again. I used the mower the first year for about 10 hours and then put it in my...

When the snow flies, I remove the 210 loader from my 2210 tractor and store it in the shed until spring (which happens to be the first week of March this year :) .. Over the winter, the lift...

I don't know much about front mounted snow blowers for a 2210. Let me start by telling you how my 2210 is laid out. It has a 210 FEL and a 54C mowing deck. It seems to me the front mowing deck...

Hi I have a Deere 2210 Compact Utility Tractor with hydrostatic drive. Mine is the type that has the hydrostatic pedals (forward and reverse) and the lever for high or low gear or neutral. To...

Tractor will not start. When trying to start my Deere 2210 compact utility tractor, it had a slow crank on a known good battery & directly connected to starter/block with good jumpers, etc...

Greetings all! Just got my first JD equipment. JD2210 and a JD950. The 2210 will turnover, but it won't start. The battery is good and it isn't slow to turnover. Any thoughts? Thank you in...

Anyone swapped a suspension seat onto their 2210??? Looking for ideas. Thanks!!!

I have a JD 2210 and the PTO shafts will not turn when I turn on the Power Take off (PTO) Switch. This tractor has two pto shafts, one for a 3 point attachments and one for an mmm. When you use...

cancel,cancel,cancel

Morning Gentlemen, Perhaps some of you will be able to help me with my JD2210 as the local Green Dealer has been unsuccessful, though they made lots of money on service-calls. First, I love the...

I have a JD 2210 with 54c belly mower and I'm wondering what a good speed to mow at is? I don't know the type of grass, but I keep it about 3-4 inches long and live in Michigan. Any tips on...

Is there a diagram avalible on the John Deere 2210 tachomitor opperation?

My 2210 has rear end problems. Dealer said it needs a new hydro unit, which I guessing is the whole back end because going to cost over $5,000 to fix. It goes backwards just fine, but struggles...

Morning Gentlemen, I started this post on an ongoing thread, but I think it is perhaps more appropriate to start a new thread. I am about to go from a JD 2210 (newer mdl is 1023E) Green to...

Hi everyone. I was just out clearing some snow with the tractor. I drove it into the snow, then pressed the reverse pedal, and as I went to press the forward pedal, it was hard to reach because...

Does anyone have drawings or installation sheets for a John Deere LVB24981 kit. I would like to know which plug to remove to install the pipe plug and what the supply and return ports are? This...

Hi, I have a John Deere 2210 tractor with a 62c mower deck. I only use this tractor for cutting lawns. The 62c mower deck is terrible, its always broken. Is there a good belly mower that can go on...

Hi, I never realized that diesel fuel was so dirty. It was definitely time -or overdue- yesterday to change the fuel filter on my 10 year old 2210. It was BLACK, looked like someone added about a...

Just want a 2nd opinion on the direction of the piston/rod. I removed them all and marked which cylinder and assumed that the arrow on the piston points to the exhaust, but can't honestly say I...

replacing sleeve and seal clean the area around case before removing the 6 bolts. place a pan under the case to catch the oil that will drain after removing the case. after removing the case pour...

Recently purchased a used JD 2210 with a FEL and 62" belly mower. I bought this for my wife to use, figuring that a "Good" name like JD and lower time tractor should be pretty reliable for her...

I am looking at a 2004 JD 2210, it has 800 hrs, 210 FEL, comes with 54 belly mower, 47 in PTO driven JD snow blower with hydraulic chute, tire chains and 5ft landscape rake. One owner who took...

I have had my 2210 for roughly 10 years now, and I love it. Starting last fall before winter, I noticed my tractor has having problems going uphill when the grass was wet from rain. The rear...

I have a JD 2210 and it is currently leaking transmission fluid in the rear just above the PTO shaft. I've looked on JD parts to see if i can get a new gasket or something, but I can't find any...

I live in Western Michigan and can't find a place to rent a tiller from, so now i am looking to purchase. I have a JD 2210 and from what i read, the King Kutter TG-48 is a good option from a...

I heard definite grinding the last week when I operated the 4 wheel drive in reverse. Then the front wheels started locking with the rear wheels pulling them. So at first I thought it was the...

O.K. so I've searched and searched and can't find anything that will directly replace that punky little 20Amp alternator on my 2210. Here is my own upgrade from the original unit to a very common...

im looking for a cylinder head that goes on john deere 2210 used, can anyone direct me on where to find one

I have a John Deere 2210 that I got this past fall. I started using it this winter for snow plowing with the FEL and it works great. I just started noticing a red/pink fluid in the snow if I let...

I have a bit of a quandary. I... a) Ran my 2210 out of fuel for the first time...in a blizzard.:cold: b) I cannot find my service manual, and c) Despite the 2210 allegedly being equipped with...

I installed two rear lights on my JD 2210 this past fall. I connected them into the pigtail on the rear so they are controlled with the current light switch. Yesterday I was out working on the...

I have a JD 2210 with a FEL and will be doing some snow removal in the winter. The FEL seems to get in the way of the headlights so I want to add a light or two to the ROPS or somewhere above the...

I've been sick of my turnbuckle stabilizers since I bought this tractor. Put it on my list to build some telescoping links. The other day the weather was nasty all day so spent the day in the...

Hi All, I've got a 260 backhoe I got a great price on, but I still need to purchase the subframe and power beyond hydraulics. I'd like to try and do the installation myself, but so far I've had...

There is a local guy selling a 2004 John Deere 2210 with 210 loader and 54C mower. It has 550 hours on it, and looks great. He is asking $8650 obo. What do you all think a fair price is for...

Hi All, One of the attachments that I've wanted to add to my John Deere 2210 SCUT is a John Deere 260 backhoe. Best price I've been able to find for this has been $5500 for the whole package...

GREETINGS - FIRST POST --- I HAVE A JD 2210 WITH 400 HOURS ON IT. I USE IT TO MOW, SOME FEL & SOME GRADING. THE TRACTOR RECENTLY STARTED LEAKING HYDRO FLUID AFTER IT WARMS UP. IT LOOKS LIKE IT...

Good afternoon all. I would like to first thank all of those who have contributed to the 2210 repair threads. Great information, pics, part numbers and descriptions. I have learned a lot from...

The screw securing the PTO Control Lever has broken. I can still change the PTO selection manually with a wrench, but it's not a "on the move" type of change. This has happened before - I'm a...

I am anxiously awaiting the delivery of my new (to me) 2005 Deere 2210. Delivery guy #1 that I hired pulled a no-show, so the 400 mile round trip did not happen today (or I would be out just...

Hi Everyone-I am new to the forum,but have enjoyed reading and learning from it quite a bit. I am moving up to a new Deere 2520 after a great experience owning and using my 2210, and all of your...

I need the rear PTO casting for a John Deere 2210 or 2305. My casting is broken inside. Would buy part or whole tractor. Galen

I need the rear PTO housing for my 2210. A housing from a 2305 will also work. Does anyone know wher one might be parted out?

It's EXTREMELY cold here today. I think the coldest it's been since I had this tractor (about five years, but only 240 hours on it). I have a little bucket on the tractor and a little TR3...

Hello all. I really enjoy this forum. Has anybody put an older model sickle mower on a JD 2210 or 2305? What are my limitations, HP, weight, width? I am contemplating buying one but don't...

JD 2210 FEL, 54" MMM, 46" Snowthrower, 54" Snow Blade This replaced my JD 400 Industrial backhoe/loader and 1977 Wheelhorse C-160. Forced to sell the JD 400 by my neighbors who complained that I...

Always worked fine and last night I went to plow snow and they don't come on. 4 ways still work fine. Thinking it is not bulbs since there are two and unlikely they died in unison? What should I...

I was at my dealership last week and a customer was in there getting his JD2210 fixed after the engine to transmission driveshaft failed from lack of grease. It also broke the front case on the...

hi i've had a John Deere 2210 for 6 years. i initially got it to snow blow (48" snowblower) my 1000 foot driveway but once i discovered the joys of tractor-dom, i couldn't stop finding tractor...

Help, I have a JD 2210 that the Mower Adjustment knob will not stay in place. I have located the culprit which is a spring clip that goes under the tractor and keeps the adjustment cam in...

Hi everyone. My son was using the tractor today and Told me it was stalling when he was digging out trees. Later on it wouldn't Start. He checked the fuel filter, there was fluid in the sight...

Hello everyone. My son went to use the tractor yesterday to cut the lawn. Then went to move some dirt and dig out trees. Told me the tractor would stall when lifting something heavy. He left...

Need to repair the rear 540 PTo on my 05' Deere 2210 SCUT. I know I need some of the internal driveshafts and gears, but beyond that not sure just yet what I need. Looking for used parts...

I've got a leaking seal on the front axle driveshaft input seal. I got the part on order so I have not seen the part and I have the drive shaft removed so I can see the seal but it's not clear...

Hydraulic fluid has dripped from my mid-PTO shaft and emptied the reservoir; well, at least no fluid is visible in the window, and the drips have stopped. Based on all my Internet research it...

Hello everyone. I'm trying to help repair a starting problem on a 2210 compact tractor. The battery keeps going down and that is probably the problem. However, I checked the voltage coming from...

Hi I noticed a couple 2210's at the dealer with around the same hours as mine - around 700 - and they both had a lot of free play in the steering wheel, the worse one had about 1/8 turn of...

Guys I have a friend of a friend thats selling a 2004 2210 with FEL and ballast box with 350 hours on it for $6500 but the PTO doesnt work. The owner said his brother his a rock with the brush...

When i pull up on the yellow knob the pto clutch seems to slip

Hi Everybody.. Last time I was here was about 8 years ago when I was purchasing my very first SCUT and you all were very, very helpful and I ultimately selected the JD Mdl 2210 w/ FEL, 56C and...

New to the site, hope someone can help. I purchased a JD 2210 with a front snow blower. Throws shear pins to beat the band. If I have it in float mode and the blower goes lower than the front...

According to the 2210 oem parts on line you only could buy a whole new front axle differential for app.$900. A mechanic at the dealer checked the service manager OEM part screen and surprisingly...

Hey All, Anyone ever had an oil pan leak on a JD 2210? Do I need to pull the motor to fix this? I can get all the bolts off, but not sure if the oil sump will keep me from getting the pan off with...

My John Deere 2210 just died yesterday ...its never had a problem... but it died and refused to start a couple of times when it was in gear, but started up ok in neutral...then it just died...

Problem: when turning tractor in sharp turns heard thumping noise from front axle differential and put it on work bench. By turning the shaft axles there is some play lengthwise (so towards shaft...

Thank you all for setting up these forums. Since 2004 owner of a JD 2210 in eastern Colorado near Denver, trying to maintain weeds and some grass on 2 1/2 acres with the compact 2210. Found out...

I looked at a JD 2210 with a belly mower and FEL, 256 hours, 2006 at a dealer. Asking price is $10,200. Any opinions on the tractor and price? Also, I could not find what the bucket is rated for...

Bones72

S $11000 forJD2210 a reasonable price with FEL, 62 in. MMM, and a front mounted snow blower with 200 Hours ? Bones72

Is $11000 for 2210, with 200 hrs, FEL, 62 in. MMM, and front mount snow blower a reasonable buy? Bones 72?

What year was 2210 last Manufactured? Bones72

I have owned one for 6 years and love it! My Dad has owned two kubota's over the last 16 years and just bought his first John Deere. Praise the Lord anotherone came home! thanks JC

Hi All, I've got a John Deere 2210 and I've got a (barely) used 210 loader that I'm considering purchasing from a dealer up in New York. I would have to get it delivered via freight carrier...

If you want the new 54" blower to put on a 2210 it clearly states that is will NOT fit the 2210. I could not figure this out, so I ordered one from my john deere dealer anyway. The next day the...

my JD 2210 it has done all and more for me, I just love it. It has less than 700 hours on it and I have been faithful on maintenance. Over the last two weeks I have noticed a vibration from the...

well not so much lift issues, but lowering to the varrious heights on the lift scale. For instance , it lifts all the way and lowers all the way but the settings inbetween, for 2 -3-4 inch does...

Looking to trouble shoot my JD2210 compact which is leaking a bunch of hydrualic fluid up the steering column. Anyone have repair advice? How difficult of a fix is it for a do-it -yourself job?

Well guys, I've done all I know to do with my tractor! Problem is it won't start, I thought the battery went south on me, but it's fine! How it began was I went to mow the grass and it...

Hello everyone. Great resource for owners or new to fluid Power! my 2210 is a backsaver. 60" mmm no loader Yet! $7200 with 808 hours so far so good! A little freaked about hydro filter location...

I have a 2004 JD 2210 Utility Tractor. Having problems with what I thought was the regulator. 1 - New battery = 12.86 VDC with no load 2 - When started, battery test at 12.75 VDC whoile running...

Is there a trick to getting the rear axle off to replace the seal? There are two bolts that I can't get to without taking the transmission out!

Anybody using rim guard in the rear tires for ballest on a 2210? Thanks

i have a 2210 getting slower in low gear. use to run about 5 miles an hour (example) now run about 1 mile an hour example almost wants to stop. runs fine in high gear 500 hours changed...

I recently finished building a cab for my 2210 and am in the process of making my own heater using a chevette heater core and a 130cfm dc muffin fan. Myy question is how or where do i tap into...

After pricing cabs I quickly decided the only way I would ever be able to afford the luxury of snow-removal without fighting the elements was by fab'n my own. So about a month ago I got serious...

My blinkers just stick on. They come on with the key, and stay on regardless of any turn signal switch or light switch position. Occasionally I can get one or the other to turn off, or blink a few...

Hi. I am new to the website and have a question regarding my recent purchase of a 2005 JD 2210. I would like to add a 12 volt receptacle to power a pull-behind sprayer. I was wondering if anyone...

I would like to have a grapple for my 2210. I could build the grapple, thanks to the ones that I have seen on here. :thumbsup: My problem is figuring out the hydraulics. Do I just "T" in to...

My 2210 just turned 200 hours, so I am getting read to change the transmission hydro fluid, the front axle gear oil, the fuel filter, and the oil. The tractor is six years old; I am the second...

Had a little seeding job to do so dragged out the ole tandem disc. The JD2210 didn't seem to mind too bad. It worked better after I built a weight rack and added 250lbs. ;)

My JD 2210 compact utility tractor will not start? When I turn the key with the shifter in neutral the dash lights come on and I hear a single click. The starter does not engage. I have had the...

it's 2004 2210 i was pushing stone for about 2 hours tractor was getting pretty warm and the pedal faded away,the tractor still moves but not very well oil in trans gets very hot, i had a u joint...

My 2210 with 600 Hrs shut off yesterday and will not start. I had been running it various time through out the day with no issue and now there seems to be an issue with something not letting it...

After replacing the hydraulic steering ram and changing all the filters I hooked up my brush mower and discovered the rear PTO will not turn on. The fluid sight-glass in the rear shows appropriate...

My John Deere 2210 has had a small fluid leak out of the power steering hydraulic unit. Now it has gotten worse and I need to repair it-just as the grass is getting out of hand! Has anyone done...

Any common problems 52 in deck has been working fine for 120 hours and turn to 6 inch high and now won't turn to lower deck. Not hit nothing,pulled 4 ft disc in garden and now time to mow, any...

I have a 2005 JD 2210 with 130 hours. Comes with an "Edge 62" belly mower and a 200X quick detachable loader. Excellent condition, garage kept. What is it worth in a private party sale?

I just finished wiring in some LED lights to the ROPS of my tractor. I used a 20A fused lit switch hooked to the + of the battery. My question is can the lit switch drain my battery down if it...

Is there a kit that I can add to my JD2210 that will lift the deck independently from the 3pt??? Seems I've heard of that??? I'm tired of running my 3pt arms in the ground when the deck is down...

HELP!! I own a JD 2210 with a 47" snowblower (front ount). I have a couple of issues. I find it extremely noisy, like a rattling noise, when blowing light snow and operating at about 2900 rpm...

I have a JD 2210 on which I installed the power beyond kit in August 2008 to supply hydraulics for the backhoe attachment I purchased. The backhoe was on the tractor since then, last week I...

Hello all, Sorry for the repost, but my previous post earlier today has disappeared. I am hoping you can give me some ideas where to look for the vibration noise I am getting. Here is the...

Curious if this adapter will work on my 2210 Deere? https://www.imcuniverse.com/store/easychange.htm

Now that we've had 2' of snow, I'm thinking it's time to invest in a snow plow for my JD 2210 CUT. The FEL / bucket did a decent job but the plow would have made the job easier. Is the JD front...

Both are used. Here's all I know so far: Deere: 4WD 62C mower deck, 300 hrs, Hydro. $7,900 Kubota: 4WD 60" RCK60B Mower deck, 431 hours, Hydro. $6,900 Dealer claims Deere tach was replaced...

I have purchased a used JD 2210 with FEL, Box Blade, and 54 C Belly Mower. I have a manual for the tractor but not for the Belly Mower. I want to remove the Belly Mower to service the tractor...

Hi guys, I purchased a used JD 2210 in March '08, and it's done everything I've asked of it and more. Recently I decided I'd like to measure the hydraulic pressure to the FEL just to see if it's...

Anyone guide me to a detailed thread concerning replacing the HST cooling fan on my JD2210?? Thanks in advance for any help!!! :)

When the JD BH first came out for the 2210, I bought it and with it came a swivel seat. It is a pain to swivel. Has anyone found a better swivel seat for this combo?

Greetings, I have a 2004 John Deere 2210 with 275 hrs. I use the machine for all sorts of light yard work as well as mowing. Recently I had an emergency incident that required the brakes to...

I need to replace the leaking battery on my Deere 2210.. today. Being Sunday, the local dealers are closed. I need to get to the auto parts store but need a battery part number.. which I cannot...

2003 model, 210 Loader, 4x4, 706 hrs. Whats it worth?

Just bought this tractor from a guy. He said the pto quit working about a year ago. Its a 2003 with 706 hrs on it. Any ideas on where i can start?

Hello, New to T.B.N. I have the opportunity to purchase a 2003 John Deere 2210 with a 210 front end loader for $8,599 from a local dealer here in Wisconsin, delivery included. There are a few...

I just purchased this tractor. I got a mower deck 62" without any kind of mounting brackets. Anyone know or have a picture of what I may need to hook this up?

Hydraulic 5' blower on a JD 2210? I've got a chance to get a 5' hydraulic blower for a decent price, that was designed for a skid-steer. I'd like to convert it to run on my CUT. I'm thinking...

I just got a used 2210. While I think it is the right size/style tractor for me, the grungy appearance bothers me. The last owner did not take very good care of it. Paint is chalked, decals are...

Got a chance to buy a 05 - 06 JD 2210 4x4 for 12 gees with 100 hrs. Includes -60" belly mower -Quick attach front loader w/ 5' bucket -Post hole auger w/ 12" bit -60" rock/landscape rake -48"...

This afternoon I picked up the iMatch and ordered the Femco Folding ROPS for my 2210. I installed the iMatch this evening and it was worth every penny. I do not know how people get alone with...

For grins I decided to check the hydraulic pressure on my new to me JD2210 and was supprised to consistently get 2400 psi compared to the manuals 1987psi. I used a 4k psi gage mounted to a quick...

I am looking to purchase my first compact tractor. I have found a 2005 JD 2210 with 108 hours, 200CX FEL and 54" MMM. The 2210 is in perfect condition and looks like the guy never used it...

The local Cub dealer had a pair of CubYanmar sc2400's on display out front each complete with mower and loader. I didn't ask price, just for yucks took a peek. There are a lot of nice features...

I have JD 2210 Gas with a 54" Deck and fron loader, wheel weights, as well as the weights on the back - In very good shape, always in my shop, never sat out It is a 2000 with 500 hours, I...

Hi All: Its been guite a while since I've been on (2.5yrs actually). In any event, I was running my 2210 over some brush today and ground up my transmission fan. I went down the road to my...

Can anyone answer as to how fast in MPH the JD 2210 will travel in high gear on the road for transporation purposes. Thanks.

Hey, I'm seriously looking at selling my JD 2210 now. We've been talking about it for awhile now and getting serious now. Its just not big enough for what I'm doing. Its a 2005 with 136 hours...

Hey everyone, I've got a John Deere 2210 that we mostly use primarily for its loader capabilities on our paved parking lots. So the tire wear on my turf tires has become excessive and it is time...

I have viewed this site for a long time and recently became a member. Anyway, I have not been able to find an post on outfitting a Femco weatherbrake onto a 2210. I am interested in purchasing...

First post, great web site. A problem arose last week on my 2210, the blinkers on the roll bar are now on all the time regardless of the position of the master switch or the position of the...

Having gone from my 2210 to a 2520 and then back to a 2305... I thought I'd post some of my thoughts on the machines.... I sold my 2520 about a month ago. For those who followed my ad's, I sold it...

Hi to all and hope you can help me. My friends 2210 recently started to smoke at the 3000 rpm mark which is where he has to run it for mowing and snowblowing. The fuel filter,oil filter,and air...

On John Deere's website, the survey suggests a 2210 would be ideal for my use. (Mowing an acre, plowing snow on a long drive, spreader from the 3-point hitch, etc.) Does anyone have any experience...

Just wondering where owner have mounted aux. switches on there John Deere 2210? I am going to mount 1-2 lights on the rollbar and 1 back-up light on the back Thanks, Dan

Has anyone ever hooked something like a tiller from a Kubota B-21 to a JD2210? I can get a hold of one but I don't know if the PTO shaft is going to be the right length. Before I haul my tractor...

Anyone know where you can get replacement front tire for JD 2210. I had the dealer deliver the tractor with Carlisle R4s (industrial). I tore up a front tire and need a replacement. Dealer...

I'd like to put a grapple on my 2210 and was wondering about my options. Is adding a 3rd scv possible on this unit? Is there someone who builds them or should I design my own?

Thinking about a 42" or 48" rotary cutter for my JD 2210. Would like some feedback on your experiences including weight issues, 3-point hitch issues etc. Considering the JD LX4, Woods RCC42 or...

Recent new lurker to the forum. I have a 2210 and will be buying a 48" tiller. Either a JD or KK, trying to decide if it is worth $600 more for the JD. Either way, I understand that the PTO shaft...

Is there any market on finding good or excellent Front End Loaders for 2210 JD Tractors , and do they ever come down in price for new ones ? I was quoted $3,500.00 for a new one that comes on and...

I have been told by 800 number, in the small give away manual, that the charge is $ 75.00 for the Actual Shop Service Manual for my 2210 JD Tractor ? Does anyone know where I might get it a...

Anyone get a Cruise Control kit installed on their JD2305? Could it also be put on a JD2210? Thanx, Dave.

I converted a JD 47" 2-stage from a 318/420/430 to my 2210. Long story short I bought the snowblower with the intention of converting it for my F911 but that didn't work out. Although I've wanted...

I have a friend wanting to sell his JD 2210 with 210 loader, bucket, 62C mid mount deck, imatch, LX-4, box blade - 150 hours. He wants a cab tractor now (too hot in Texas). How much is it...

Found this on Ebay... http://cgi.ebay.com/John-Deere-2210-Tractor-w-Loader_W0QQitemZ7573153334QQcategoryZ63988QQrdZ1QQcmdZViewItem

JD 2210 and Jinma 6\" chipper - questions Is it possible (or adviseable) to run the Jinma 6" chipper from a JD 2210 or JD 2305? The 2210 is 23hp with 17.7hp at the PTO @ 3000 RPM's. It has a...

Would use strickly for snow removal... curious if the 5' or 6' blade will rotate all the way around without detaching?? Thanks guys!

I just finished the web page about the Optima battery I installed for my JD 2210 in Sept. If you are thinking about install this battery then check out this web page. :-) On the main menu...

I finally got some time to do the web page for the block heater I install in Sept. If you need some information and pictures about install block heater for JD 2210 Check this web page out...

Winter is here and I am thinking of a cab for my 2210. What have you other 2210 owners purchased? Can you attach pictures of your cabs? I just don't know how much money I am willing to spend...

Dose any one know if it is possible on the 2210 to add hydro lines to the fel for a grapple bucket? In addition what is the lift capicity of the 3pt hitch on the 2210 in lbs? thanks

Hi, I live in central Michigan, and am looking to replace my JD318 and Ford 8n with a CUT. Been looking at the JD2210, but wondering if a good used 4100-4300 might be better. I have about 5...

Spec\'s of the a 200CX loader on a JD 2210? Does anyone know what the lift Height and weight is for the 200CX? The manual doesn't give any spec's Thank you Jim

Has anyone had any issues with their oil light coming on a start up? I know this engine is in a lot of John Deere equipment so anyone with this engine can answer this; 4010, 4115, 4210.... When...

Hi all, This post is somewhat in response to Iowa2210's problem with his MFWD axle. Although he only had 20 hours on his machine and hadn't used his in the winter, I was talking to another poster...

I'm looking for a tractor to mow about 4 acres of lawn and move a little snow around. I've been considering the JD 2210 and the Bota 7610. Both tractors look similar on paper, with Kubota...

Is Deere planning on replacing the 2210 in the near future?

Looking to buy a ~48" tiller for my 2210. Deere suggests the Deere 647 or the Frontier RT1140-1150/RT1240-1250 series. I have also look into the Woods GTC-52. The King Kutter is value priced and...

I went to several dealers Saturday. Looked at a BX22-1830, Massey2300 and a JD 2210. The TZ was quoted at $11,271 with 60" MMM. The BX 2230 w/ 60" MMM was $10,145 and the BX 1830 was $9,705...

I have average skills, do all my own car work I know the oil change is straight forward what about the transmission and filter Anything I should watch out for , any "gotchas"? (other than a big...

I burn very easily and anticipate spending lots of time on my new 2210 when it arrives this week (likely to be Friday). I've been looking for a hard canopy and have only found one made by Femco...

Does the 2210 have them? If so how are they activated? JD dealer didnt seen to know know much about the machine when I was looking at it. Also if plugs how well do they work in -20+. My other...

I am a first-time tractor buyer looking for the right compact for my property. I have about 1.5 acres of lawn (more accurately field), and plan on a .25 to .35 acre garden, along with other odd...

I am a first-time tractor buyer looking for the right compact for my property. I have about 1.5 acres of lawn (more accurately field), and plan on a .25 to .35 acre garden, along with other odd...

Hi all, After reading PDe's post about his Woods BH6000 hoe on the JD 2210 I am about sold on one for my 2210. I live in NH and called my local dealer and got a quote for $ 7000. Got another...

Hello, I just got my mid mount mower today for my 2210 John Deere. I put it on and everything. And i have a couple questions. First off, are the wheels on that thing supposed to be locked ridgidly...

Although I have been reading these discussions for some time and have found them very useful and informative, I am a newly registered user and this is my first post. Unfortunately, my...

I presently have a JD 455 with 40 loader and 47" snowblower with quick hitch.Dealer offered me a 2210 with fel quick hitch and rear hydralics as I plan to put a woods backhoe on it.My tractor and...

buyjd-ML-650277-ML- Brand specific. Moved to JD Buying/Pricing forum.

Hi, I'm new here and have been lurking around reading the posts. I have a level 2.5 acres (1.75 pasture) and a 750' gravel drive. I dont need a mower but do need a FEL, box scraper and...

Here's what I'm looking at: 2003 John Deere 2210 Tractor/Loader 74 hours 54" MMM Loader (not positive on loader size) Asking price is $11,900 Any thoughts, comments on the price?

I am looking to purchase CUT to take care of 6+ acres of land. 3ac need bush hogged, 2ac mowed and the rest tilled. Looking at spending no more 17k for whole enchilada. I am looking to get the...

Thanks to all of you I have now have a 2210 with a FEL Have to read all the literature, but am more than ready to put er to work. Any special precautions on break in period, fluids ect. Rather...

I’m new to this forum so have mercy on me. I’m desperate for advice and the 0%/36 month financing deals are soon coming to an end, not to mention the grass already needs mowed. Keep in mind that...

<font color="green"> I am going to buy a four foot rotary cutter to attach to my JD 2210. An LX4 from JD is out of my price range so I have looked at the Woods Brushbull 48 and a Bush Hog...

I'm very disapointed in the 54 blade that i have for my JD 2210. I was thinking about getting a FEL mounted Curtis Plow but i decided that i'm going to build my own plow that has a longer with and...

I recently found this site and a huge thanks for all the information you folks post. For a rookie like me, it's awesome. Looks I may be coming down the home stretch on making the commitment to...

For a while I was set on the JD2210 but as I've been working on the price quotes I'm surprised the 2210 costs so much more. A BX2230 with FEL, 54" mower, bagger delivered is $14K. The 2210 with...

\"new\" backhoe for JD 2210 I just recieved info on a 5'6" backhoe for the JD 2210. Made by EMB Wallenstein, it prices out for somewhere around $5k, with the subframe kit. here is the link to...

Does anyone know who might make a "rock grappler" attachment for the bucket or 3 point hitch on my new JD 2210. If the rocks are below ground level the are hard to get a hold of with the bucket...

Looking for a back (box) blade for my JD2210. What width/weight would work for a gravel drive way thats 150 yards long. Any recommendation would be great. Sorry if this has been talked about Thanks

I have installed XM Satellite Radio on my JD 2210 Tractor. First I had to install a 12 Volt outlet in the Dash. Next week I will probably hard wire the XM Receiver into the electrical system...

I just thought that i'd post some pictures of my JD 2210 with the curtis cab, heater and console in there just incase anyone was interested in any of that stuff and wanted to see it. This is a...

Hi, i have a JD 2210 with a curtis cab and the new curtis console. I also have 4 of curtis' work lights. Two on front and two on back. I was driveing the tracor at night the other day and i was...

Hi guys...getting ready to buy a 48" tiller and am looking at Ken Sweets line and also at TSC. Ken's shipping is very resonable and comes in competitive for what TSC wants. I just wished I could...

Hi, i was plowing with my 2210 and the FEL when i noticed some hydrolic fluid comming out of the transaxle i saw it in the snow. I took to into the garage and on the left side right above the axle...

Who here has been plowing snow with their John Deere front blade and Front Quick Hitch? I was plowing our road and driveway during the 1st big storm this year (yeah, I know it is March). Wouldn't...

I posted this also in the attachment forum. I know that some were wondering if the standard SpeeCo PHD would work on the JD 2210. I finally had time Friday to put it together and try it. I had to...

I know that some were wondering if the standard SpeeCo PHD would work on the JD 2210. I finally had time Friday to put it together and try it. I had to use the farthest hole and got 6" of...

Spring will be here soon and I'm looking for suggestions on a landscape rake and box blade make and model for some upcoming projects I've got in mind. I have a 900 ft gravel drive to keep level...

Hey everyone, i have a JD 2210 wiht the 210 loader and 61" bucket and the front blade. I came across the Curtis loader mount blades and have been thinking that i would like to get rid of my front...

Which is better B7510, JD2210, JD4010 or CK20?

Hey everyone, i was just wondering if anyone knew if i could use forks for a 410 loader on my 210 loader becuase the dealer told me for the forks its 1200$. and i found someone who can get me some...

Hi, I just got my 2210 yesterday and i got it with the front blade and the loader with a 61inch bucket. The problem is that when I lift up the blade while on the tractor it only lifts 4 or so...

Thanks to Jim Wilson who, in another Kubota thread, mentioned that someone over in the JD section was running a thread about a Woods BH6000 being put on a JD2210. The thing is pretty; just too...

Has anyone had any issues with their oil light coming on a zero degrees and below? When I start my 2210 at 80 hours, with the engine heater on, the oil light comes on for 3 seconds or so. I have...

My wife and I are considering upgrading our lawn tractor but the sub-CUTs we are considering may be too big. Our property slopes away from the road and our little Husqvarna 1542XP gets worn-out...

I posted this question on the JD forum and I'll include it here. We recently bought 52 acres and we are building a new house. I have looked at both the NH TZ24DA and the JD 2210. Both have...

Recently bought 52 acres and we are building a new house. I have looked at the JD 2210 and the NH TZ24DA. I will need a tractor for mowing about 6 acres of lawn, snowblowing a driveway that is...

Well, I took delivery of the 2210 complete with the snow blower installed. While waiting for snow to arrive, I have been doing some dry runs! A couple of questions: (1) I seem to get some...

Last week the John Deere dealer dropped off a 2210 with a 54" mid-mount deck for us to try. We've not yet purchased it, but after spending the summer looking at all the competitors, we thought...

My needs are mowing an acre of lawn and a mile of walking trails around my farm; clearing much snow from a 100 yard driveway and a high snow berm caused by highway plows; occasional moving of...

I hate to be the one to re-open a thread but... Maybe someone out there has done this by now. Just to refresh, The only major option I am missing on my 2210 is the Steer-able Dual Rear Brakes...

Has anyone out there purchased Horst Welding attachments? I am looking into the #LD35 Pallet Forks attachment? I have a <font color="green">Deere 2210</font> and am considering some pallet forks...

What are the pros and cons here? I am leaning strongly towards the Kubota- after all: 1. Both tractors are Japanese anyway!! 2.Kubota is $2000 cheaper! 3. I always liked John Deere; that is...

Next time you get on your <font color="green">2210</font>, could you turn your key to the "<font color="purple">ON</font>" position (not running) and see if your <font color="red">Water...

I have been looking for several months and have gotten several quotes from nice dealers around the area. I am looking for a loader to these machines along with a box blade and MM 60"ish finish...

Hi Everyone, I'm a new owner of a JD2210 with FEL and 62" mid-mower with a couple of questions... Since the tractor is new (< 3 weeks and < 8 hours) I am not yet familiar with "normal" tractor...

How\'s Deere 2210 compared to Cub Cadet 5254 Newbie here, I am in the process of finding the tractor I want to buy next spring. Cub Cadet and Deere are the only ones that are handled fairly close...

I am starting to compare the Deere 2210 with the Kubota 2230 both with a front loader and 54"-60" belly mower. I have owned two smaller Cub Cadet mowers, but this will be my first "at bat" in the...

Greetings, I'm new to this sub-compact tractor market and need advise. I have 5 acres, most of which will just need finish mowing, but I also need to plant a few dozen trees, do some minor...

I have a John Deere 2210. The only 2 things I want are " <font color="blue"> Cruse Control </font> " and " <font color="blue"> Dual Rear Brakes </font> ". Other than that... I am very pleased ...

This is my first post, but have been reading for a while and decided on the JD 2210. Got a lot of good info and ideas from this forum and the posts before I bought. Bought the JD 2210 in June...

I am looking into either the JD or Kubota (would prefer the JD). It is going to come down to price. I am getting it with front loader and box scraper (already have the JD mower). What have some...

Trying to figure which way to go I got the samr price quoted for each . Any coments will be very helpfull.

Sorry the pics are mixed in with shots of my property and pole barn progress. So far I have 68 hours on it. Most made up of digging and using the box blade. This clay is like cement...

My need for a CUT w/loader is probably only 200 hours spread over the summer and fall. Rather than rent a machine for hundreds per week, I'm thinking I'd be better off buying one of these...

Need your help . . . I was at the Massey Ferguson dealer, and he was very professional and polite when I asked him for difference among these three tractors. The obvious were a single bucket...

I am buying a new JD 2210 with a 62c mower deck and would like to put on a grass bagger. JD does not offer a bagger kit for this tractor although they do offer a system for the X models which use...

I have 8 acres that I need to rough cut. I've been looking at the 2210 but just noticed the 790 on the JD web site. I know the 2210 is small but the price is sure right. I think I can get the...

I had only 10 hours on my JD 2210 when the hydrostatic cooling fan broke. I was using the rotary cutter mowing down 1/2 inch diameter sapling when I heard a slapping noise. I stopped the tractor...

Powerful little machine and with the right tires she can put that power to the ground too. I have the HDAP tires from the X-series tractors and they bite hard in dirt. Blading with the frontier...

Gonna take delivery on my 2210 next week. 54 inch deck, 54 inch loader and imatch. I also have the cleat tires-ag tires. Trading my 1979 YM155D Yanmar w/loader and rear deck along with 8100...

Last evening after mowing I decided to clean the underside of the mower deck. Wet mowing conditions so far this spring had caused the mower to take on quite a bit of dirt/mud/grass residue. The...

Sorry for the BH in my post. It is not a backhoe nor is it a brush hog. It is a Block heater to get that thing started on our col winter days in the great white north. Sorry

Hi I've been looking for a tiller for the 2210. I think JD reccomends a 48 inch. I thought I'd check here and see what some of you guys are running for tillers. Anyone try one larger then 48? I'm...

Please help. I am looking at purchasing a new JD 2210 with FEL and 54"MMM. I have price that I think is very competetive. My concern is that it won't be big enough to do all of the work I want it...

I am trying to decide between a JD 2210 w/mower and box blade and a Kubota BX2200. I went to deere.com and was able to get a list pirce on the 2210 using their product configurator but I did not...

JD 2210 review. Had \'er for a couple weeks now... My baby is a 2210 with 2 speed Hydro, 4x4, mid and rear pto, 3 point hitch, 23 hp yanmar diesel, Imatch hitch, HDAP tires and grill guard, 62"...

these units were priced each with FEL, MMM, rear tiller and blade; JD 2210 -$15300, Kub $18500, Farmall- $20000

Mow 5 acres but use a 620ztrac for yard. Move some dirt around and getting rid of my old 8N that I used for rough mowing and bushoging. 4100 w/410 loader 60"mid deck is $14,000 used but perfect...

I need a tiller for my new JD2210. Any recommendations on size and brand would be appreciated.

<font color="green"> Seems like it wasn't too long ago this forum contained a posting about an unbelievable price for a John Deere 5220 tractor that had scam written all over it. Use the below...

Hi folks, I originally posted in lildozers' "2210 or BX2230" thread - because I felt I had similar needs - but GregJ suggested that I start a new thread - so here I am...

Thanks to everyone on this forum for all the info. I finally took the plunge today. New JD2210 to be delivered next week. I feel like a 16 year old about to get his drivers license. I can't wait!

I have also been lurking on the forum for a while and have made a few posts and am still amazed at the great source of information. Thanks again. I am just about ready to make the deal on the...

Well, I'm trying to decide on a BX2200 or the Deere 2210. I expect to get a deck and FEL What are your experiences? Which would you buy? Any idea on price in the Toronto area? Thanks in advance

Folks, I have 2 acres of property with 1 acre of fine manicured lawn in MA. I'm looking for a machine that can be used for mowing, bagging, snow blowing and possibly a tiller and a small...

I have a 5ft KK rear blade. This past week I had my first opportunity to "play in the snow" on my gravel drive. Since 3ph height control is somewhat lacking with the JD2210, I was wondering if...

I hope it's okay to post this, I have couple of items for a JD2210 listed on ebay: Rear tire chains (these probably would fit a Kubota BX too, but I'm not positive)...

Does anyone know if the 2210 is set up to add a rear remote or not? Or, does anyone have this installed on their 2210? Chuck

Just got my 62C deck delivered and I am about to install the attaching kit. Noticed on the parts list that it calls out for (2) Lift Rod Assemblies (item E the part with a yoke on each end). Is...

I have a JD 2210. I wish it had cuise control on it, but it doesn't. And JD doesn't offer it as an option. Is there any after market cruise controls that would work on this hydrostatic transmission?

Hi Was looking at a few snowblowers for the 2210. Seems most dealers around here have the Buhler Allied or FarmKing, same blower as far as I know. Any coments on the Buhler brand and would a 50...

Has anyone ordered the parts and technical manuals for their 2210 tractor? I beliveve the cost with shipping is $126.55 for both manuals. Are they worth it? Hopefully they are better than the...