Search results

First it was suction control valve now replacing clogged injectors. Does anybody know of a 5 micron spin fuel filter to replace the Kubota. Nobody can tell me the rating on the kubota. Anybody done a add-on

My M7060 has been having trouble with power loss. Diagnosed and fixed as contaminated fuel. The suction control valve had to be replace along with fuel filter change and water seperator. It is acting up again.. Does anybody know what rating is on fuel filter, micron size. Was reading that...

Sadly I've had to use my KTAC twice with just over 60 hours on my M7060 HDC 12. The adjusters worked with me and unlike most insurance companies I feel that KTAC actually have customers interest at heart. I highly recommend buying it. My dealer has also been exceptional Gatorland Kubota. I'm...

Anybody know if there is such a thing

I trying to see if my problem has been shared. How many have a service for a SCV suction control valve solenoid. It could cause high pressure in the fuel rail

Now that I've had my first problem that produce the check engine light and discovered that nobody has access to computer. I'm upset I've always used my error codes to find and fix problems on my Ford's, how is that Kubota has kept it hidden? Has anybody hacked a reader yet.

This morning I got my notice a package delivery, along with the follow the delivery truck updating map and promise of a 9am delivery. By 11am is was now saying 12:30pm delivery, by 2pm it was saying 9PM delivery. About 6pm it was saying bad address, please update. The address was correct and UPS...

Already lost my 3rd function FEL valve to a stick, ripped wiring out $2300. Ktac Now I've got a check engine light, back to shop, think regen problem Was under it again and now the fuel tank skid plate bent, really flimsy and they didn't roll the front edge up. So it just traps sticks. Upon...

Happened after a parked regeneration cycle, it speeded up for about 20 minutes then came back down and we went back to work. engine warning blink a few times now stays on reduced power 50% no buzzer Dealer says they have to pick it up

I'm planning a skid plate for my M7060 cab tractor. The two things to protect are the plastic fuel tank and the FEL valve both are easily damaged by sticks. While I'm at it I'd like some bigger steps into the cab. Right now I'm looking at Grip Strut 7.5" deep step material. One step would be...

My 50 year old Sidewinder had a rough life, the front edge had rusted through, the front beam cracked from striking the PTO shaft, the whole right corner had struck something and fallen off. But it would still cut however when I got my new tractor you couldn't get much travel and ground...

Planning on using some stainless 3/8x16 rivet nuts to hang some skid plates under my Kubota M7060. From my research the two handle pop rivet like guns, fail when using the larger sizes, mandrels break and rivets get crushed unevenly. I found some simple wrench driven setter that looks like it...

Anybody built any guards for the valves pics please

Today we did tree and stump removal, the wicked 66" grapple did good job pushed over 6 to 8 inch oaks and ripped up root balls from chain sawed trees. Got my old 6x6 sidewinder bush hog rebuilt, new blades, clutch plates, reworked cat 1 pin bars to work with bush hog flex link and cat2 pins...

So something got in that poorly shielded FEL 3rd function solenoid area and ripped a connector off the solenoid. Dealer will pick and return and I filed KTAC insurance claim, supposedly will have to pay $250 deductible. So now I going to have build some skid plates for that valve area and the...

Runs AC & Waterpump less than 100 hours, anybody else have trouble with AC belt slip

I migrated from a 1966 Ford 3000 diesel to a Kubota M7060 with 30" radials. When I hooked up to my old FMC Sidewinder G720 6' bush hog cat1 to my M70 cat 2 I couldn't raise the deck much at all, even with control arms on the short lift holes. Also naturally the PTO shaft was higher off the...

Today was first day with my new driver and a box scraper on my m7060. It was drive way repair, one of my rain runoff spots had gotten lower, than the area it was supposed to drain too, held water and the dually deliver trucks had made it into a mess. So I had him mount the box blade with all...

Part number and where to buy THANKS

So this very tall pine tree grew enough to block one of the Three satellite's my dish uses. It was too big for my chain saw, and I didn't really want drop it, because the woods are thick and will crash into lots of stuff on the way down. So we plunge cut it all the way around it, and drove...

got a M7060 with 3rd function on the FEL dealer didn't install dust covers, asked for a pair, but female plug is too small, what sizes do they go buy

Had to tighten belt pretty tight to get to stop squealing about 1600 rpm

What have you done to protect the fuel tank and the valve assemble. A stick bent my protection plate over valves got bent down about 8 inches

My sometimes is difficult to get into snail mode, any tricks anybody has learned

So here is what I've got a harbor freight hand pump, golden rod fuel filter 1", 20' of fuel hose, Goez 3/4' locking fuel nozzle. chain fall drum lifter. The output tube from pump is 1" od thin wall tube. Planning on a 1" male npt to 3/4 pvc glue with a piece of 1 inch heater hose and clamps to...

I don't like leaving attachments on the ground outside but have limited amount of space under the pole barn and don't want to move stuff to get to the one I want. My FEL has quick attach, has anybody built racks for storing grapple or buckets?

Sometimes I can shift easily between creep, lo, hi. Other times it is just stuck. I put the shuttle in neutral, tranny in neutral and press the clutch. When it is shifting you can feel movement of the large gear sets, and it takes little force. When not shifting you feel springy brackets...

In the cab there is aux plug up on the right apron. Its got two circuit 25amp hot all the time and a 15 amp hot on run. The 15 amp is already shared with 3rd function power, and air seat. Two things I want hook up, cameras front and rear and cab monitor, going to use the 15 amp hot on run...

GRAMMER MSG97/741 450lbs rating and oversize seat with depth and tilt control. Adapted to fit Kubota seat mounting plate using 1x3 tubing

Installed my fit right hydraulics on my M7060, It went perfectly smooth, the quality of the fittings, the flow restrictors, heavy duty cylinders, the hanger for the top link, hooked to two aux valves with float. Killer

So today I put my piranha bar on my 84" bucket and went out and found a 4.5" 5" diameter pine tree. Put bucket on float with heel on the ground and bar up an inch, backed up about 2 feet then rolled forward into the tree with some momentum. Raised and curled and popped that pine out root and...

To make getting off the tractor unnecessary to change implements. Does somebody sell this?

You find them in blue, yellow, red. All from China have cast frame threaded to screw into 55 gal drum, adj pickup tube, and gas station type nozzle around $170. Anybody own one? Comments?

Had to drive about 20 miles with tractor, no trailer. So top speed is limited to 25MPH, top gear the speed limit light comes on yellow in the dash and sets the top rpm at 2k. Had my new air seat installed, turned all the lights and flashers on. Road very nicely, got to the site had to lift a...

Pretty stuff getting into creep, neutral and clutch in helps. I know some people say park is stuff but mine is fine.

Has anybody found a plug for the rather strange looking 3 pin plug next to the cig lighter. It has 25 amp hot all the time and a 15 amp hot on run circuit

so have good credit score. 2017 I buy a new Ford finance for 60 months PNC gives me best rate, credit score climbed a few points. 2018 I use the car again to buy a Kubota rtv because I could get the best rate on car loan and had paid PNC off. This time used my credit union for best rate credit...

Ready to mount my new air seat but need 12vdc. Tthe aux power connector has two circuits 15A on during run, and 30A on all times. Want get to the 15A for air seat and front/rear camera/monitor. So WSM schematics show a unused plug behind right side liner. Anybody know any easy way in, maybe you...

Worked with Nick at Toughseats.com they built me a Custom Grammer model Air seat. I will have make adapter for the different bolt pattern to mount it but the M7060 just has flat plate with 4 bolts over the AC. Model MSG97HD/741 in 12vdc, with right armrest only, cloth black, rated 440lbs, has...

My WSM shows no wiring for the compressor, or any mention of the air seat, any body know?

Construction Attachments $656 10 teeth 120lbs W. R. Long standard $532 9 teeth 78lbs From EA web site Any other choices and why or experiences Thanks in Advance

Since I'm old and fat maybe somebody can save me some time with routing the wiring into my cab from the FEL. After spending a little time with pallet fork it is kind of obvious a second person is needed because you can't see what you're doing. So I bought a backup system with two camera's. My...

Saw a video of the rocking action front to rear, is that caused by too much water in the rears, a wave cresting over in the tires. Or air pressure in tires? I've got radial tires soft side walls.

Found the radio bracket and fuse, cat 2 to 1 bushings, A U SHAPED 1/2" HYD LINE WITH TWO DIFFERENT SIZE FITTINGS ON THE ENDS about 3 inches by 4 inches looks like bypass for something?

During today's walk through we test the hyd pressure at 2100rpm at third function connect on the FEL, and it read just hair under 3000 psi, factory spec says 2770 psi, now the rear hyd valves were all about 300psi lower? Why? Also after looking at the 72" bucket it was obviously too narrow for...

First off a $47.00 set up fee, next it is based on total cash price of property and mine was setup for 5 years to match my 0% loan. Your discounts are not considered. So paper work shows total cost for 5years plus the $47.00. So subtract the $47 from total and divide the result by 5 years and...

Any way of making advance find whole phrase like torque wrench comes back with any instance of either word, can you do things put quotes around to find total phrases, advance search seems pretty dumb

Mine is now in hand, If you need section let me know I'll scan and post, just don't ask for everything.

Nothing to do with tractors but very fascinating Einstein's Quantum Riddle | NOVA | KPBS It also explains our dispute with China

Everything works on it does have any collector value?

It fairly expensive $1800 on M7060, is hyd not mechanical, found a picture of the kit on eBay, loader valve gets changed and more lines and another control level. Two rumors it slows down the bucket curls and limits the upward curl, and makes it hard to bump the bucket to get dirt out. But I...

What you built for, or added on, to your quick connect pallet fork hanger. Pics please. Just any kind of improvements or add functionality ideas

Planning on adding some weld on chain hooks on my bucket and pallet frame, but has anybody done that on their grapples?

I couldn't get them to match my cash price when I switched at the last minute to 0% loan, discount went from 15.5 to 12.87 and you had to buy Ktac at 1.3%. I didn't mind Ktac after I found what it covers. What have you seen?

Read cat1 2500psi~ cat2 4000psi~ I've only read about one regulator for FEL and 2500psi~ is normal

I've always kept a flapper on my exhaust for water and mud dobber wasp, what do the new tractors have to keep the annoying mud dobbers out?

Watch several videos on adding rear valves. From what I could tell valves are castings that bolt directly to what looks to be the rear diff and you stack them and bolt them together with cap on top to block supply and return hand brake style of cables from the cab activates them. Could anybody...

options, creep, guard, 3 LINES 2FD, Loader 3rd, Indus tires, 72 buck, pallet, wsm, 200hr supplies, later TNT, Wicked 66, toothbar

1. Constant on valve for post hole digger 2. Two way valve with float detent, top link in out hold and float 3. goes to end of stroke and shuts off remains closed no float What is the proper name for these valves

HYD LEAK DOWN since I'm ordering TNT, I think a FEL and 3pt hitch bleed down test. How long should they hold with box scraper on rear and HD bucket up front. Hyd pressure test would like it at max for heavy pallet say 2750# at least Any quick test for draft control? Set tire width just...

So which style of blade heavy dense mowing, and can the same blade serve underbrush, small tree under 1 inch. Kubota vs Woodridge in 72 " group. Front Mount vs rear. thanks for experienced opinions.

As part of tractor research I watched a lot videos. What I find funny is American ones mostly you can tell the drivers either little experience or are afraid to scratch their tractors, watch the once from third world countries much more entertaining and if tractor works for them it is tough.

Should I add it? Can't think of any use for me, don't need a snow blower, but only $377.00, or can you add later easily. Watch all those messick videos about snowblowing for a loaded grand l5460, I've put almost ever option it.

I'm looking for a backup camera with nice size monitor that will let me see my three point hitch but also let see my brush hog 6 feet so that I don't have to stay turned around when I'm working backing up to clear brush around buildings and trees. I usually raise it up back over under brush and...

I'm in Florida and maybe will the owner of new grand l6060 so I'm concerned that antifreeze won't do much for rust on rims. From experience of using empty oil drums filled with water the sloshing oil left in the drums floating on the water kept them from rusting would that work in tires?

KUBOTA RTV-X1100C WSM HST & WIRING Thought some might find helpful Kubota Postimage.org

Monday afternoon picking up a new unit, think I should do the rear wheel neutral inspection anything else? Tx