fluid

I just purchased a Bobcat MT120. The owner of the Bobcat shop warned me that if there were any warranty issues related to hydraulics, Bobcat would take a sample of the fluid and that using any rental equipment would have the possibility of voiding warranty since attachment fluids mix. Has this...

I have a New Holland TC40D. I was pushing a large tree that had fallen with the 16LA loader and blew two hoses. I changed them out but have a large leak coming from somewhere mid-point on the tractor. Oil is dripping constantly. It appears to be in the area of the manifold diverter box...

Is there a way to run chemical diagnostics on hydraulic fluid similar to what is done for engine oil? Or actually the automatic transmission fluid in the truck. If so, who does it? Just wondering if I can pull samples and have them analyzed to check for wear of components, and remaining life...

I bought this tractor (2021) used, about 1 year ago with 175 hours on it. Today I was adding some rear remotes and had to undo hoses connecting to the power beyond port on the tractor. This fluid looks way too dark for 315 hours, right? The oil smells fine... should I be worried? The manual...

I recently acquired a Case IH 454. Mostly been good but has given intermittent hydraulic issues e.g. bucket won't lift. The guy before me changed (or got someone to change) the hydraulic fluid and (I assume) put the right stuff in there. When I purchased it I thought it was low on hydraulic...

I'm having trouble with my L370Grand losing oil from the HST vent. I mean it flows out in a steady stream. I pulled the filter off and all 10.5 gallons ran out. Is this normal?

Hello You'll, I noticed that my 4WD Shift Lever is leaking (pouring) Hyd Fluid from where it enters the Sump. After consulting with my local Mahindra Dealership Service Dept, I was informed of their backlog and the lead-time to get it looked at/worked on. One of the Serviced Technicians...

Kubota wants an arm and a leg for their hydro fluid! Is there a comparable fluid I can use?

The FEL is using the normal place you would fill the hydraulic as a return. Is removing the return the only way to fill the tractor hydraulics?

I somehow lost the dip stick at the rear for checking hydraulic fluid level. I ordered a new one from local dealer but it has been on backorder since last January. I'm to the point that I will make my own. If anyone could provide a picture showing the length I'd be all set. Would be greatly...

I have a 2000 L3710 Grand HST that suddenly started blowing all of the fluid out of the transmission breather. I mean it pours out. Everything, FEL and PTOs and drive work fine. I changed the hydro filter and that didn't help. I did recently change all of the loader lines but that was 10 hours...

My brother has a Case 580c backhoe with no brakes. The master cylinder is empty of fluids. There is some dispute if DOT 3 or hydraulic fluid is needed on certain years. Nothing in his manuals and nothing on the master cylinder caps. The serial number on a tag on the engine is...

In my Rural King RK37SC, I've always used the Rural King Providence store brand of "Premium Trans-Hydraulic Oil, Multi-Trac Formula for Use In Most Applications" which meets the John Deere J20C spec and many other specs, and costs about $15 per gallon. But they also sell "CAM2 PROMAX Premium...

In my RK37SC, I've always used the Rural King Providence store brand of "Premium Trans-Hydraulic Oil, Multi-Trac Formula for Use In Most Applications" which meets the John Deere J20C spec, and costs about $15 per gallon. But they also sell "CAM2 PROMAX Premium Universal Tractor Hydraulic...

I bought a new 1526 last year, time for 50 hr. service. The OM says after changing hydraulic fluid and front axle fluid the systems must be bled. Here is my problem...the pictures showing the location of the bleed screws in my OM looks nothing like my engine and I'm not at all sure where the...

Hi all. This is my first post here. I recently replaced all the hydraulic fluids in this tractor, except the rear axle. I think I found the drain but can’t find a fill. Does it get the fluid from the same place as the main gearbox or is it separate. If it’s the same then I guess I already...

Will the tractor supply traveler brand universal transmission fluid work in a 2010-11 mahindra 5530 4x4?

Earlier this week I decided to change the transmission/hydraulic oil in my Zetor 5211 and do a filter change/screen cleaning. After draining it out and cleaning the screen and doing the filter change, I went to town to buy a bucket of 80w90 and a little extra. Well, the local tractor supply...

I hit 600 hours, and my hydraulic filters were due, fluid was coming up and I've been wanting to swap the fluid to synthetic for a while, so all that happened today. Draining it was pretty straight forward. I used an oil extractor through the fill port and pulled out almost 5 gallons. Then...

Our 333G calls for John Deere Hydrau, not hyguard. Part number TY27366, but I wondered if anyone uses a different brand. Our machine still has a year warranty left on it, and I was worried about voiding it if I use off-brand, because 2.5 gallons is about $90.00. I'm open to using other brands...

I have a New Holland 640 hay roller. I had to repack the bale density cylinder. Does anyone know what kind of oil I need to use to refill it. It is a closed system with no reservoir.

I have a handy dandy bucket with a hydraulically belt driven unloader. I use it for single handedly putting mulch around plants and bushes. Anyway, I put it on the FEL and when I connected the hose all seemed fine until I tested the action. One direction it works great. WHen I try the...

The bushings on each end of the drive shaft was shot so I replaced them also and charged fluid in transmission and filter then I let it set for a year or longer before I started it up transmission took off like it's suppose to but after a few minutes it slows down pulling

So I got recently 2 pails of amsoil hydraulic fluid. https://www.amsoil.com/p/amsoil-iso-32-100-synthetic-multi-viscosity-hydraulic-oil-hvh/ Got it in iso32 because I use my tractor in the winter too and it gets pretty cold up here. Paid $500 for the 2 pails, but now starting to have doubts is...

I have a Kubota B6100 w/ front loader I just bought. Trying to change/ fill the hydraulic fluid but the loader hose is attached where the fill plug is. What’s the best way to do this? New to tractors.

I see Summit recommends a VG 32 or VG 56 hydraulic oil in the owner's manual. I will be using VG 56 because of the warm climate. Does Summit recommend a particular brand or brands, or certain additives? Thank you -Andrew

Hi, All: I just removed a blown hydraulic hose and should add back what was removed from the hose, so, I am asking: 1) What type of fluid to use (is it 80W90)? 2) Where to add the fluid? Is it one of the top bolts on top of the transfer case? I see a dipstick there but no idea what that...

The shaft for the 4 wheel drive is leaking fluid at the rear of the tractor. The shaft is loose and I can slow down the leak by pushing the shaft back and or rotating it. I am wondering if there is a seal that I can replace. I am trying to find a diagram with part numbers so I can repair this...

So I buy a new Massey Ferguson you tell me I have to replace all the hydraulic fluids in all my accessories my plows my discs and everything else that hook directly to the tractor. Because it uses powertrain 827xl semi synthetic fluid, and my disc and plow from 1940 used conventional oil I can't...

Lost all Hydraulics after changing fluids

So I have some stuff in my fuel ( Kubota L3540) , I tried to siphon it out to no avail and I really dont want to pull the tank so I was wondering of I could vacuum it out with my shop vac??? What do you think?

OK,so here is what is going on Yesterday I GO TO START TRACTOR ,I NOTIC A STEADY DRIP COMING FROM THE LEFT SIDE OF TRACTOR,I LOOK AND IT SEEMS TO BE COMING OUT OF TIMING COVER. (SORRY ABOUT THE CAPS LOCK BUT EYES ARE NOT THAT GOOD) I UNSCREW COVER WITHOUT IT RUNNING NOTHING,ZILCH. SO I START IT...

Hey all. Would anyone have any ideas why I seem to be moving fluid from the hydraulic system (tank under the seat) to the main gearbox (yellow dipstick aft of the engine?). Seems to be happening this time of year when I have the Kubota v plow on it and using it. Didn’t seem to do it over the...

Hello to all, Does anyone know who makes this for Kubota? Obviously, Kubota is not in the refining business and has someone make it for them. Your help is greatly appreciated. Thank you in-advance, tstex

I am working on a ym180d , Can you tell me what type of oil is used in the gear box?

I have a 4630 93 two wheel drive and want to change the fluid can somebody tell me where the drain plug is

Can the HST fluid level be too high or is it just a fluid reservoir for the hydraulic system?

I just finished completely draining and replacing hydraulic fluid and filters on my ck 25 kioti. Now it is not engaging . Barely moves and a whining sound.Looking for any idea's.

I have a mid 2000s Kubota R520s that I bought used and is kind of a clunker. Since I’ve owned it, hydraulic fluid overflows out of the brake fluid reservoir while operating it after a short period of time. The LST oil pressure light stays on during operation and despite that, the tractor still...

I bought a used Yanmar SA424 and immediately changed all fluids and filters. The tractor ran great all summer, but I was slow to address a small leak in one of the backhoe lines. I topped up the fluid in the fall, and noticed that the steering was stiff initially when cold, but would return to...

The book states this goes in the trans., and front differential, that's all it states, any ideas? I found trans. fluid and hydraulic fluid. Thanks in advance.

I have read condensation can do this . would putting air vent on top trans help this. any body try this

I guess I have three questions: What gear and shuttle shift position should it be in when I check fluid? Should it be running or not running when I check the fluid level? If running, at what RPM?

New to the chat. My 2006 Kubota Transmission fill port has a hydraulic return line attached to it. How do I fill the transmission with fluid when I’m changing the fluid? Any advice would be appreciated

I don't see anything in the little window so I called the service department where I bought my tractor. He told me the fluid is clear and unless I know it leaks it should be fine. No dipstick, why is there just a 'window' if the fluid is clear? Pictures for your perusal.

The attached photo is of my transmission sight gauge and I'm trying to determine if it's overfilled or is low. I don't remember if there's an interior tube within the square acrylic outer tube (or case) or if the golden trans fluid is supposed to fill the entire square case. I had a cylinder...

Does anyone have a source for a cheaper cap for a kioti windshield washer fluid reservoir cap. Mine didn’t fit when I bought the tractor and now it’s completely missing. The only one on line was around $18 for something that shouldn’t be more than $5.

How does one go about changing the filters with out changing the hy fluid? It seems this would be a huge mess when taking the filters off. Or is it a matter of draining the fluid first in to a bucket or two. 2003 NH TC45D Thanks

Gotta clean this up before the misses gets back home, yikes! Was using BY85 backhoe on my TYM T574H and afterward, scooping up the spoil pile with the loader bucket. Going to check levels, but I don’t see anything on the fittings up front, could this be from the backhoe? Any easy way to find...

Can anyone tell me where the hydraulic fluid is checked and added in a Kioti CX2510....I think I found it but just not 100% sure. Thanks in advance guys. sheldon pinsent

Wondering if I can use Castrol UTF in my hydrostatic transmission for the transmission / hydraulics in my Emax 25? Manual says to use API GL-4 grade, 80w gear oil. Can't find these specs with the castrol. Thanks!

I never have really understood what the hole in the bottom of the tractor was for. It has a pin in there to keep it open and occasionally fluid / oil drips a bit, but the other day, fluid just started spewing from there. I shut the tractor down but more than a gallon of milky oily fluid was...

Ive got a new to me 2008 branson 2910i and am going to do a hyd fluid & filter change but not sure what to use in the front axle. Do it take the same fluid or do you use gear oil? Would like to find an owners manual but no luck so far.

In researching hydraulic fluid levels for this tractor am I correct in that I check 2 different places. 1). The transmission level for transmission and 3 point at plug next to clutch pedal. 2). The hydraulic reservoir at the controls for the loader with dipstick. Thanks.

Yesterday I was bush hogging a hilly pasture and had a brake system failure… luckily I had just reached the bottom of a hill when the anomaly happened! I’m trying to wrap my head around what happened, how to prevent it, and any advice or insight the forum may have to offer. some things about...

Hey, love the forum, first time poster, long time lurker. I recently picked up a 2006 GC2300, reading 395 hours (I don't think its 1395... the last hydraulic filter read 2017 and 195 hours). Its in pretty good shape, looks well enough cared for. I went through and changed all of the critical...

Good morning, new member first post… i got my first tractor almost two years ago, ita a Kioti LB2214 and i think the year model is somewhere around 1989. It’s mainly used for mowing certain areas at my family hunting property! Great tractor for what i need, zero issues and has never not started...

Hi, I need to top off my hydraulic transmission fluid in my Mahindra max 25 HST and I was wondering if this fluid is OK to use. Thanks!

i own a bolens with hydrostatic drive it also has a hydraulic ram for lifting the blade, it seems as if the rearend has a thicker fluid in it than the ram can anyone tell me if the fluid in the rearend is different than the fluid in the lift? i thought it was 90 wgt but its red and smells like...

Will low hrdraulic fluid keep the PTO from engauging?

2024 TYM T25 with about 15 hrs. I bought it new last October(ish). It came with the front grapple installed and I used it a bit last fall. Then the snow came and I went to the bucket which hadn't been installed until then. At some point I learned how to check the TDH fluid level through the site...

I bought a new-to-me older diesel Ford pickup. It's in great shape but has some frame rust I would like to neutralize. Could I just get a couple gallons of fluid film, a gallon garden sprayer and spray the underside myself? Has anyone done this? Is the viscosity thin enough on a hot summer's...

fluid leak down front right tire on 4 X 4 NH Ford 445C? Does anyone have any suggestions to help me get started? Thanks, Fred PS I'll post a photo tomorrow.

I have a 1961 Ford 641 with no dip stick to check the hydraulic fluid. How do you check this fluid. Thank you

I have a new to me 2008 MF1528 HST with 1520 FEL. I want to do a complete fluid change. However, there are no close dealers near my area. What would be the best hydraulic fluid for my machine? It will take about 8+ gallons of fluid. I do not know the history of the machine, so no idea what...

I just did a fluid change (100 hrs.) and I had to add red dye to make the hydraulic fluid visible. I had overfilled it and had to syphon some out. Now I am a little confused - with loader and 3pt arms up I have nothing in the sight glass. With them down the sight glass shows full with just a...

What is the correct hydraulic fluid for the kubota l185dt

I have a manual transmission tractor. It loses about 2 quarts of hytran fluid in 10 days or so. There are no visible leaks, drips, wet spots that I can see whether it is running, parked or just sitting there. There is nothing attached to the rear remotes. It has a front end loader and...

My Mahindra 4510 loses transmission fluid regularly. As much as a couple quarts in a week or so. Cannot find a leak or a drip or a wet area anywhere, parked or running. Curious as to where this fluid could be going without a trace that I can find. Thoughts. Thanks.

I have a small single axle 4X8 dump trailer. The pump, hydraulics, and battery are under the bed. How do you check the hydraulic fluid? To get to the pump and tank I have to raise the bed. Normally you want all hydraulics relaxed to check fluid level. There is a dip stick on the cap for the...

Looking over the names of the New Holand UTF. None I Recognize, Currently have New Holland Mastertran Ultaction in now. Has been in tractor around 5 years so going to do a fluid change sometime this year. seems like this is the right choice but it mentions designed for CVT. Mine is HST also wet...

I have a 2016 NH Workmaster 55 w/900 hrs and recently the Hi/Lo shifter started getting very stiff/hard to shift. It was low on HD fluid so I changed fluid/filter and it seems to be slowly getting a little easier, but nothing like normal. I have a couple of questions I hope someone can help...

I have a 2000 TC33D New Holland and want to change the antifreeze. A google search does not tell me how nor what anti freeze to use. Older woman DIY so any help appreciated.

Time to change the HST filter on the M62 and the Owner's Manual sez to drain the fluid first. Big PITA to do so, and I'm wondering, if I work fast, how much fluid will I lose if I don't drain the fluid first? Anybody done it?

Need to change Mitsubishi MT 320 I just purchased. Is best 80/90 oil or what else. I know 80/90 is suggested.

I just performed a Cub Cadet Zero Force SZ Hydro-Gear transmission fluid change. This was no fun! I found a great 26 minute detailed "how to" video on YouTube - - and tackled the job on my 540 hour mower. Never been done before, although I've done regular engine oil and filter changes. In a...

Hi, I made a post about purchasing a 2610 and we finally agreed upon a price and brought it home this past weekend. Any good recommendations for fluids? I wanted to change all of the filters and fluids to start off on the right foot. It has about 106 hours and I wanted to give it the 50/100...

I have a Century 3035, the same one that I just had the PTO issue with. After getting it going, I was brush cutting when a steering hose popped apart at the crimp. After a couple of weeks of waiting on a local hydraulics shop to make a new hose, it is back together again. I have a separate...

Hello 1900hrs on my 08 1547 had all new engine oil filter trans fluid and filters. He out April tdh in it. I see it says meets some massey specs. Started it hot was on a slight incline in high range and when i went to take off it had a delay. Got to checking fluid and it maybe down a little...

does the transmission hydraulic fluid operate the rear hydraulic lift on a 2200D Yanmar tractor?

What kind of hydraulic fluid will work in my mahindra 6500 besides mahindra brand

After I disked the garden a few days ago I rinsed the polled off the tractor and then backed it into the carport to tighten a loose bolt on the disk. I did and pulled it back to the shed. There was some mud and water as I expected. I swept the dirt up and saw the "wet spot" . Later that night...

just purchased a tractor and the hydro/tranny fluid was milky I also notice the glass eye was milky. I changed fluid and the glass eye is still milking is there anyway to clean it or replace? I tried to slide something down next to the gears and clean it but failed

So this may be something someone might be able to point me to the right folks on finding parts on the BH 7600 Korean backhoe. I am leaking fluid from one of the Hydraulic level control plungers. Need to find a repair kit for a new upper o-ring and upper white flat plastic washer. I am pretty...

I changed my hydrolic pump and now hydrolic fluid is going to the case and spewing out any ideas on what is causing this?

Hello all, Anyone with any exp with Iseki tractor ? I have a slow leak in a few spots, anyway need to top up hydraulic fluid. Seems there is a dipstick in centre console area behind shifter and a bolt type plug nearby, however the tube you can fit in there is a bout a quarter inch ...

The manual says: KUBOTA SUPER UDT-2 SAE 80-SAE 90 gear oil Why specify 2 options? From what I've read it ships with UDT. Recommendations? I'm looking at buying the AMSOIL SEVERE GEAR® 80W-90 100% Synthetic Gear Lube for it.

So, I’m gearing up for the first service this year on the 4820H. It may be a smidge early in hours, but 2 years in I feel like doing it. So, I have Rotella T6 for the motor, but I came across Triax Agra UTTO XL fluid for the transmission. Also considered the Shell Rotella HD oil. Does it...

I was looking at a 2023 Kioti 4210 se, I noticed there was green fluid dripping down from the clear hose (picture enclosed and highlighted of the hose), what is it? This clear hose is on the back of the tractor underneath (running down) the enclosed cab area.

Curious as to what the typical charge for having a dealer do the 50 hour maintenance on a T474HC would likely be? I have watched videos of this service, and it doesn't seem too tough, but some did comment on some difficulties with some drain plugs and the hydraulic fluid filter because of...

Looking to change all the fluids in Ford 2600. I can not seem to find where all the drain plugs are. I have a IT Ford Shop manual but cant find where they explain where to change it. Im sure its something simple. Any help would be great.

Hi folks, I am changing fluids at 50hrs. Front axle no problem 80/90w Engine 10w40 Rear axle expeled like 21lts of what I think is gear oil.(is this right?) Rear axle, transmission and transfer are all together?? and do they use 80-90W gear oil. Can´t find drain plug for tractor hydraulics at...

i cant find what this part is in the mahindra catalog it just shows a square hole where this goes on the center case. my haudralics drained out of it. like a plug was released, not under pressure. it is on a 2015 gear series. thanks

Any one ever use Traveller hydraulic fluid for their Hst kioti ? Can’t find the Mobil orr a couple of the other brands in stock https://www.tractorsupply.com/tsc/product/traveller-premium-tractor-hydraulic-fluid-5-gal-t806391 thanks

Hello, I have a hydraulic leak and I think the culprit is the shaft which is used to open and close (what I believe is) the hydraulic lines. Something has caused the shaft to have an oblong rotation and it also seems like it has more wiggle than it should. I've included a couple pictures. I've...