kioti

Hello, new member here. I've got a Kioti K9 2400 bought new in Spring of 2022 that has 35 hours on it. When I start it up cold and back it out of the barn, the CVT belt often squeals loudly. Once underway, it stops making noise after a moment. If I stop and shut down for a minute, upon starting...

The hood latch/release mechanism isn't engaging. I.E. When I close the hood, the latch doesn't work to keep the hood closed. I've lubricated but the issue doesn't resolve. Advice?

nx5510 hst Got a deal on a 3-point fencepost driver. You raise it hydraulically, when you release, it goes down as fast as possible. To vent that fluid ASAP, it's got a 1" dia return line. Wondering if there's a place on the 5510 to add a port to dump directly into the hydraulic reservoir?

looking at adding a TB-Max to my tractor. Dealer says I can use existing hydraulics and dump the fluid straight back into the return, no pto pump needed. I don't know enough about the hydraulics to know if it will cause issues in the long run (foaming, overheating, etc.) to be worth not...

Let's just say things happened, just can't have nice things and now I need a new bucket curl cylinder for a bobcat ct2025 with the fl7. I'm not sure how to measure to get an aftermarket but if I can figure it out I know it would be about 1/4 the price of bobcat, also my local dealer isn't great...

This is Aaron's new Orange Ultimate Rack on his Kioti out of West Virginia, as you can see even the pups are loving it! Don't miss out on any deals, sign up for our email list and check out our site! Check it out HERE Learn More

This is the first tractor I've owned with the electric PTO engagement. HST (no clutch), no mid PTO just rear and no neutral or disengagement lever for PTO. Just the round yellow engage/disengage switch. Is it something I've missed or is it no longer possible to turn the tractor PTO output shaft...

I'm considering buying a used (27hrs) Kioti CS2210 with the SB2410L and a backhoe. It also has the cab enclosure with heater. I looked up weight and with the loader its almost 2000lbs but couldn't find the weight for one with the backhoe and enclosure. First question is will my 2012 Ram 1500...

Just taken ownership of a new EX5310 tractor in Tasmania First impressions were generally positive however i have a slight issue with the gear shifts being very finnicky/stiff/tight to change. Similarly the shuttle shift and accelerator lever are very tight and don't seamlessly glide or move...

I have a 2006 Kioti DK 45 with 1,000 hours. It is currently in the shop due to a broken gear in the front axle. The specific part is: T4682-43441, Gear 16 Bevel. This part is listed as obsolete when I try to order it from my dealer. I went directly to Customer Relations at Kioti Corporate in...

Buy an Ultimate Rack Combo and Save $300! Our best selling Ultimate Rack Combos just got better! Order a combo and enter code: QH2023 at checkout to save $300 off your order, we'll even throw in a free 5n1 Tool Holder! That's over $500 in savings when you include free shipping ORDER HERE .

In the process of replacing the clutch in my LK 3054. The hour meter reads 430.0. My buddy gave it to me because it would lose forward power while going up hill and he is not a mechanic. When i got it, the situation got even worse and the tractor got to the point where it could not move while...

Seeing the post this morning about the decline of the new tractor market made me think. What is the expected deprecation of used tractors? How much per year or per hour can you expect your equipment to lose in sale value on the used market? I'm sure it matters if you are picking up a JD or...

Hi, I have a 3 1/2 year old Kioti DK2510 with about 120 hrs and been having cold weather starting issues for about a year. I used the tractor all summer and no problems, but now that the temp dropped below 25 deg and the symptoms are back. Symptom: When attempting to crank, get only "click...

We almost never have any discounts/coupons/sales, but heeeere we go! www.EverythingAttachments.com Travis

We have a Kioti CK30HST with a KB2375 backhoe. The other day, the bottom pin for the boom fell out, and lots of damage occurred. Right/left swing hydraulic pistons busted (and have since been repaired), but the current damage is the bent upper pin. I'm looking for some advice as to how to...

I just discovered this after doing some heavy bush hogging with my 2610 - this is the left stabilizer arm, and both that U-shaped joint was bent and the pin was snapped off. Any idea what these parts are called so I can order them? I looked at Michigan Iron's website under the hitch section, but...

I am most likely buying a used 2021 Kioti DK6010. I can get a new Kioti backhoe with a $1000 rebate bringing the price down to $9000. I am wondering, is this the best way to go? Is there a really good aftermarket backhoe that I should consider that will save me a decent chunk of change? The 2021...

I'm still relatively new to tractors and implements, and my dealer is closed till Monday so I figured hey, I'd ask here in case this is a serious thing. The dealer got my RC1060 in Wednesday, delivered it yesterday. I ran it for ~30 minutes yesterday, then an hour today. When I got it out...

The last couple of weeks I have heard quite a few radio ads by Bobcat of North Texas (DFW area) specifically about their tractor line. Got me wondering if they have inventory. For those outside north Texas, they have 9 dealerships from Longview (about an hour west of Shreveport,LA) to...

I have a Kioti Compact Tractor With a KB2475L backhoe. It came with a pretty wide bucket. I want to buy a narrow bucket, about 8” wide. Do they all fit the same? This is my first Tractor, so I’m still learning. Unfortunately, I did not get the backhoe manual with my tractor. I just want to make...

Hi everyone, newbie here. Thought a 1025R is all the tractor I ever need but want to get a new and reasonably priced heated/AC cab, bigger size for bigger root grapple (66-72"), and more lifting capacity to move a 2500 lb scissor lift over lawn/gravel. Was ready to buy a DK4210SE HST Cab but a...

I've never owned a tractor before, and it's been a learning curve. Got this thing less than a year ago, and put about 65 hours on it, mostly mowing with a flail. Yesterday, I had occasion to fire it up to rescue the 4x4 pickup my son managed to get buried in the mud. I didn't mind--figured it...

new proud owner of d45 with kb2085 backhoe found other threads that said was same as 85, but found lots of differences any help with sourcing parts and manuals for this old girl? thanks in advance

I am 90% going to buy a grapple next spring. So am considering adding the factory 3rd function before the tractor is delivered. It's about $1200 installed (2/3 parts, 1/3 labor). I'm pretty mechanical and can install my own (although given reviews of the CKA162 instructions its worth the...

Hey guys, just bought my first tractor, KIOTI CK3510 HST and wanted to see if anyone has any better ideas to resolve problems with KIOTI. I bought it brand new off the dealer lot. Started it up for just a minute and drove it on my trailer. Got it home and the unit shut off and check engine light...

Just bought (due in November :( ) a new ck2610 (woot). I will use a snow blower, but haven't decided front or rear, yet, and since i won't take delivery until winter, I probably won't be able to make up my mind this year. Rear leaves the bucket (helpful) but requires taking off the backhoe...

I have a co-worker that ows a 2013 Kioti RC 6010, 59 Horsepower tractor. I was using it and the curl function on the stick seemed to just lose pressure and function. Even with the tractor off, when I push it to the left, it feels like there is nothing there. No resistance and won't come back...

Just bought a ck2610; thanks for all the TBN threads that helped me make the call on that. Haven't "owned" a tractor since using my dad's in the woods growing up, couldn't be more excited :) anyway ... I ordered it with the kl4030 (standard loader on the ck2610) with the quick-release 66"...

Just bout a slightly used kioti. I got my hands on a nice Woods PRD8400. I’ve got it all hooked up and even when my stabilizers are shortened all the way I still have tons of slop. Probably 6-8 inches each way. I’m beating my head against the wall trying to figure this out. Help!