kubota l35

I have a Kubota L35 I just purchased, went to try the PTO and it does not work. It seems as though it is locked up or what I would call frozen as I would call it, not from cold, lol. When I shift the pto, by the mechanical lever, with the clutch pushed in, and then release the clutch it will not...

Looking for a pin on bucket for an L35. Located in massachusetts. Bucket has been discontinued. Not a quick connect.

All the hoses on my 28 year old L35 are original. The long hose from the valve box at the bucket joy stick to the back of the tractor is leaking at the quick connect fitting. Does anyone happen to know the "hose assembly length"? I would prefer to have the new hose on hand before taking the...

It would be real handy if it is a product I can get through amazon.

I have a 2003 Kubota L35 tractor with the FEL and backhoe, it has 2100 hours on it. My power steering started being a little hard every once in a while but for the most part worked ok, then it got progressively worse over the last week, until it went completely out and when it did the...

I suspect I have a plugged filter screen in my suction line for the Transmission and Power Steering. I can't find any information on how to access and replace it. Anyone know anything about replacing the filter screen on a Kubota L35? It looks like you may have to remove major parts on the side...

I would like to put a block heater in my tractor. I won't do this until the weather gets warmer when I want to flush and drain the antifreeze. Just looking online to see which one it is and every website seems to show different sizes for the freeze plug. My tractor has freeze plugs that measure...

I live on a lake and I'm planning on using my Kubota L35 to launch and pull out boat trailers. I've installed a towing ball on the front bucket and I'm wondering if immersing the front wheel hubs will allow water to infiltrate the 4 wheel drive system in the front end and damage the bearings or...

2000 Kubota L35. 2136 hrs. Hours may go up slightly since I still use it a little occasionally. Runs and operates great. Comes with a 16 inch toothed bucket and a 10 inch smooth edge ditching bucket. Original pin on loader bucket has a straight, unbent edge. The main cylinder on the backhoe...

G'Day All, Any input appreciated to give me some direction. Whilst re-enforcing my bushfire containment line I had the hydraulics fail, not great timing but with some good advise via the forums I have replaced the coupling that connects into the hydraulic pump. When I went to start the...

I finally broke down and picked up a third function kit and a grapple for my Kubota L35. I bought this kit from Summit Hydraulics summit-hydraulics.com/product/hydraulic-third-function-valve-kit-w-joystick-handle-for-tractor-loader-21-gpm/ And I got this grapple...

Went to look at an L35 today. :) It has 2400 hrs on it, and supposedly $4k of recent work (waiting to see documentation). Inlcuded are turf tires, a set of forks, a dual grapple mounted on a large bucket with third function installed, and a regular bucket. :thumbsup: They are offering...

New to the site, but have been reading for years. Hopefully someone can learn from my personal experience. I had owned a 2004 L35 TLB for 12 years and used it with basically problem free. (only real issue was a rear wheel had been loose for years - one of those sounds you just got used to and...

I have a Kubota L37 (1993 production) with GST. The clutch died; I bought a new case clutch, plate, o-rings. I dissasambled the clutch, replace the broken pieces and reasambled. Also, when i dissassamble the clutch I** dissambled the GST valve and rotary valve. *I reasembled all and...

picked up a 02 l35 Kubota recently and noticed that when you move the shuttle lever to fwd or rev there is a slight chirp as the clutch pack engages? no delays in shifting or any other issues with the trans just seems like an odd noise for a wet clutch to make upon engagment. will do it more...

G'Day All, I need some help understanding the best and most economic option for replacing a hose that has sprung a leak. It is a hose associated with the FEL, it is 24 inches long with a straight fitting at each end. Am I best to find a Kubota dealer and get the factory item, or is one of...

How difficult is it to rebuild a leaky cylinder? What is everyone痴 thoughts here?

The lift arms on my L-35 won't move. with nothing hooked up they dont even try, I can move them by hand but nothing on there own. I have the diverter pulled out in the 3pt position and they don't move I tried it in the backhoe position and no differance. I checked all the linkage and everything...

Hi! I bought a used L35 and it appears the backhoe has never been taking off. For the love of all creatures big and small!!!!! Why will my backhoe not come off? I have followed the directions on the actual backhoe to a T (and tried other suggestions with information I found on the Internet) and...

Good Day I am on the point of purchasing a L35 for some landscaping work around the house. I need some help understanding the different types of backhoes I have seen on these machines and maybe this is just something different for the L35逞ｴ sold in Australia. The backhoe on the machine I am...

My Kubota L35 will not go forward, or into reverse and there is no steering. Hydraulic oil level is full. Bucket and Backhoe work fine. I do notice that when I check the hydraulic oil level after running the tractor, it appears to be "foamy" (don't know if that is normal). Any thoughts on...

I am about to order a 22 ton DirtyHandTools (DHT) 3-point log splitter ($899 woodsplitterdirect, free ship). The plan is to run this splitter by taking the backhoe off my tractor and connecting the backhoe hydralics to the splitter. To do that I need to buy two hoses. Any advice on what I need...

I have a Kubota L35 35hp TLB that I recently removed the backhoe to use the 3 point hitch for the first time in many years. There is a Backhoe/3pt diverter (it runs on hydraulics on this model, not PTO) valve that I have moved to the correct position and I have turned the 3pt lowering speed...

I have a Kubota L35 loader problem that would appreciate some help with. Was bought second hand at 950 Hrs and has only done 20 hours since. Problem I have is it only has 1 low gear and 1 high gear fwd rev works OK but it's only crawling or at full speed. All filters changed and oil is the...

I am in the market for a TLB and looking at a Kubota L35 at an estate auction this weekend. It is a 1995 L35 with backhoe and looks like it has been used by a private party to maintain their property. Hours are about 1800 and looks like it has been stored inside. The auctioneer says they are...

Hello I just purchased a Kubota L35. It will not crank over wth the key, I was able to put in a push bottom start to get it to run. I am in need of a wiring schematic for the machine so I can trace the wires . Also the hour meter is not currently working. What drives the hour meter? Any help is...

Anyone with an L35 willing to do me a favor? I need to know width of loader arm at the pins on the bucket. Looking for an inside ear to inside ear measurement. Thanks!

Hi all, I've been poking around with the idea of a tractor for a couple of years and I think it is time. After looking I am pretty set on Kubota L35, backhoe attaches to the frame, but still has 3 point, 4x4, dependable like a Toyota?, rugged from what I have read and is about as small as you...

Hello! I was wondering if someone could tell me how to check the pressure on a Kubota L35. The GST pressure, The GST Relief Valve Setting Pressure, The GST pilot pressure, and The GST Clutch Pack Pressure. I don't know where to check these and I don't (as of yet) have a service manual. The...

Okay. I'm back again. LOL Different piece of equipment now and the same problem. Would like chains on rear tires. LOL Can I put tire chains on the rear tires of my Kubota L35? I have seen in a couple different places where people say there is a space issue. ? Has anyone put chains on the rears...

Can anyone direct me to a website where I can purchase an OEM bucket level indicator for an L35 fel? I have been all over the internet looking without success--Some sites show how to make one, but I thought they have them already made for sale too. Thanks-------- mmm1inmt

I want to convert my TL720 loader from a pin-on to a quick attach configuration. Then I will need to rework my standard Kubota bucket and W.R. Long forks from pin-on to coupler configuration. Any advice or recommendations for products would be appreciated. I'm tired of the messy change-overs...

My Kubota L35 is in need of a new battery. I have the battery type from the Operators Manual (75D26R-MF) but I was wondering about where to buy or what brands to go with or stay away from. Would any of the large auto suppliers have dependable industrial replacements or should I just go to a...

I'm looking at my first 4wd compact tractor - I've owned a Farmall Super A in the past. I've got it narrowed down to two local tractors: 1. Kubota L35 with FEL and backhoe - 1850 hrs, $15k (front tires need replaced, rears are worn) 2. John Deere 870 with FEL and 8B backhoe attachment on...

About to pull the trigger on a metal garage as I need to get something in for my new L35 before the winter and that seems to be the most cost effective and I'm running out of time. Can anyone confirm if this machine will fit through an 8' high door? Searching around it looks to be spec'd at 94"...

Greetings: I need to do some dirt work and my tractor is way undersized. I have a 2010 Kubota BX2660. Tough little tractor but way undersized for it is 26 hp and FEL. I need to buy a new tractor that will handle slightly heavier loads, have a backhoe for digging trenches, and one that is...

New to the forum here and looking for some help. I have a 1997 L35 and want to improve the lighting. Two main questions: 1) the headlights are original and very weak. Is there a good aftermarket light that would be an easy replacement? 2) I plan on putting front and rear lights on the ROPS...

Hello... I have a kubota l35 with a wobbling front end. tore the entire top end apart to show the steering ram itself. unbolted the steering ram but have no way of getting the assy lever steering out. if anyone has any ideas or suggestions it would be greatly appriciated..thanks

hi. the problem is the tractor runs fine in 2wd then switch to 4wd and the prob starts .1st and 2nd gear seem fine 3rd and up not so good worse when under a load.kinda sounds like a dozer lug.lug.lug and so on.in the trans.or transfre case?maybe not enguaging fully in gear.help would be...

I am looking at buying an L35 Kubota TLB and would like to hear likes, dislikes, problems etc. I am choosing between two machines both of which have 1500 to 1800 hours. I will be using it to clear approx 3 Acres of Alder, Poplar etc and add post hole digger to fence approx 5 acres. If anyone is...

I am looking at buying an L35 Kubota TLB and would like to hear likes, dislikes, problems etc. I am choosing between two machines both of which have 1500 to 1800 hours. If anyone is willing to share PDF of the Operators Manual and Service Manuals I would be very appreciative so that I can go...

Hi I have a L35 Kubota, which is a awesome machine in my opinion, and I have a question on the function of the backhoe controls. I've owned it for 7 years and I have done some impressive work with this little machine and have been using it like this and never ran across another one that I could...

Just pulled the trigger on a Kubota L35 with 500 hours, to be delivered in about 6 weeks. Since I will be needing to use a grapple to clear a lot of brush piles, I need to convert the front loader to a quick-attach ( it doesn't presently have that feature). I would appreciate suggestions on...

About a month ago my left stabilizers started to slowly drop down, not only when the machine was off but running as well. I talked several friends and they said it is probably a value in the control box. So yesterday I took the lockout valve and switched them from the left stabilizer to the...

I have a L35, but no operator manual, and need to take the backkhoe off. What steps should I take? Joe

Hi Everybody We have an L35 stuck in 4wd. The lever is still attached to the shift shaft going into the transmission, the shaft is turning but it does not contact anything. We're assuming that the L-shaped shaft is broken inside the case. Does anyone know if the shift shaft can be changed from...

Hey all you L35r's, do you find a lack of power when trying to load up from a dense pile of process or 2" stone? I have read recently that it is a little short on power. I plan on working a mile of wood road up many levels. Should I be looking at an L39. The problem there would be cost.

What's a 2000 L35 with a loader and backhoe worth @ 4000hrs?

What's a 2000 L35 with a loader and backhoe worth?

Does anyone have a good source for a service manual for an L35 Kubota? Either a downloadable or book would be fine. I was trying to find one cheaper than the dealer if possible. I am also looking for a hydraulic diagram for this tractor and am not sure if this is in the service manual or not...

I am fairly new to hydraulics but am learning a lot through this forum, so any help would be appreciated. I am going to add a set of remotes to the rear of my L35 and have a valve that I want to mount beside of the FEL control. I am trying to figure out the best way to tap into for the in port...

I am fairly new to hydraulics but am learning a lot through this forum, so any help would be appreciated. I am going to add a set of remotes to the rear of my L35 and have a valve that I want to mount beside of the FEL control. I am trying to figure out the best way to tap into for the in port...

Hi, I'm new to this forum and recently got a Kubota L35. The swing cylinders bushings in the comp rods that swing the backhoe (BT900) are worn. I removed the pins but can't drive out the bushings. Tried a big pulley puller pushing against a slightly smaller dia. socket--no luck. I've heard...

I currently have a Kubota L35 TLB, that is a great little machine. I've recently got a new Kioti DK50SE HST with root grapple. I've been thinking of trading the L35 for a Mini Excuvator and the Kubota dealer near the house has this one 2007 Kubota KX91-3: 700 Hours, Hydraulic Thumb, 18"...

looking for homemade thumb ideas for my Kubota L35

Hi I am new to this site and just bought a kubota L35. I would like to change the hydrolic oil and the manual says 39 liters of transmision fluid. Any recomendations on what kind of oil to use? Hydrolic oil or transmission fluid? is it the same? Also the engine oil says to use 10-30. but it dose...

Can anyone tell me where I would look to find the Serial Number and year of my L35 TLB? :confused: I've owned it for over 8 years but I've never seen them and haven't needed them before now. I will need to buy some parts for leaking oil seals and there are parts based on S/N. TIA

Can anyone tell me where I would find the procedure to replace the oil seal on the front wheel of an L35 TLB? I am a newby to this forum stuff so I don't have a clue what I'm doing. I have oil leaking around the left front wheel of my tractor. When I go out to start it up there is oil that has...

I just purchase my first used Kubota. It's a 1995 L35 TLB and is in great shape it only has 390 hrs and spent most if it's life inside. They were asking $17'000 and I offered $16'000 and they accepted. It's pretty old...do you guys think it's an ok price?

The Woods RB72 back blade is listed as a standard duty unit for 12-40 hp tractors. My Kubota L35 is 35hp and fits into the higher end of this range and I have a few questions: Is this blade too light duty for dirt work with my 4 wheel drive tractor? It's listed as 272lbs and I'm not sure if it...

New to site , wanting to buy a orange tractor with loader , but now after looking at factory backhoe kits , I WANT one on those !!! The backhoe comes off then you have a 3 point hitch !! Thinking about buying a L35 backhoe . Its a 2000 model L35 ft end / backhoe unit , it was a rental unit...

I'm thinking of mounting a winch on either the front loader or the backhoe. I'd be using it to pull docks and boat hoists out of the lake in the fall. Also for logs etc. Any suggestions on where to mount it? My first thought was the front loader on top of the bucket. However, that might put too...

Hello, my L35 tractor will turn on, but the clutch will not engage into a gear so the tractor can move. Can anyone confirm that this is an issue with the clutch that has to be replaced/repaired? Has anyone had any experience with similar issues of a tractor not moving? Also, does anyone know...

my father and i are looking for a loader/backhoe and found this on a local website. ive operated a few in my time, but never bought or maintained one. $19,50000 1995 Kubota L35 UT - May 15, 2010 1995 Kubota L35 tractor backhoe full cab with 1613 hours. Accessories are 48 in. brush mower...

I am trying to decide between a L35 with a 4 way bucket, 1200 hours and a L3010 Has the forward reverse shifter with bushhog backhoe, Auger,5 foot bushhog,box balde 400 hours. Either one can be bought For $12000. My main purpse will be bushhogging 6 acres couple of times a year. Landscape work...

Hi I have a kubota L35 it has 1300hrs on it. When I drive it on long trams maybe half a mile the front wheels lock up. I have to put it in reverse and drive it home in four wheel drive. Any ideas what the problem is? Thanks in advance.

I feel like an idiot. My laptop was acting up for a few days and I didn't take it seriously. I knew better..I was lazy. I had downloaded all the parts manuals for my L35tlb off the web and did not save it on a removable medium, it's no longer available free (at least I can't find it). :( I'm...

Hi guys, I'd like to thank everyone for the advice that was provided, it was very helpful in my search for a tractor. I was looking for something in the 30-35 horsepower range with a loader and backhoe. I soon realized that if I bought new, I'd probably couldn't afford one with a backone. I...

The gear shift selector is hard to move from gear to gear. Noticed that the cables were damaged. Must need replacement? I am about to order from Messiks, a cable shift assembly, 34076-64803 ( Kubota L35 Parts Diagrams go to SPEED CHANGE LEVER, select ,MAIN GEAR SHIFT LEVER, to view diagram...

I would like to purchase a Root Grapple for my Kubota L35. The company I am considering purchasing this through is telling me not to purchase the specific Grapple hydraulic control, the solenoid opperated valve set up that converts the bucket joy stick to the Grapple control with a push of a...

I replaced some Hydro lines, and then drove the tractor up to my driveway. I noticed the gear selector was hard to move/shift. I added hydro/tran fluid, due to loosing fluid during the Hydro lines change, and tried to start and it will not turn over. Forward/reverse selector is in neutral. I...

I've been looking for a used 7 foot wide landscape rake for my 35hp, Kubota L35. The Kubota has 4 wheel drive and the tires are foamed. I'm going to be using the rake to maintain crushed stone drives and parking areas. I've found a used Woods LR800 that's 8 feet wide and weighs in at around...

Hello all, I've done a lot of reading, but never posted on here. There seems be a lot very intelligent users on this site so I picked it as the place to come for some answers. I currently have a '75 Ford 3000, and want to go to a kubota with a loader and backhoe. I have found a L35 for sale...

I have a Kubota L35 with 610 hours. Its in good shape, garage kept and always maintained. Only two private owners, never used commercially. Comes with 12" and 24" bh buckets. I'm thinking of parting with it because I need something that is more geared toward ag rather than construction. What do...

I'm somewhat new to this site and not sure if this topic belongs here or in the hydraulics section. If I'm posted in the wrong area I apologize. I recently picked up a real clean L35 (122 hrs) from an individual. Now that I'm hooked on the new toy, I'm thinking of implements and auxilary...

I bought a used L35 and I got a manual for the tractor but there isn't any information on connecting and disconnecting the (BT900) backhoe attachment. I see there is a seperate operation manual available for the BT900 backhoe but from the price, Kubota is sure proud of their manuals. Can anyone...

My dad bought a used Kubota L35 tractor with backhoe, and I used it on the job sites, well anyway i clear land and its pretty usefull, but Im getting a bigger one and want to sell this one, it guess while pushing brush, my serial sticker got riped and I never wrote any of it down and my dad lost...

I just bought a used Kubota L35 & I'm thinking of buying a used York rake with scarifiers and blade. I'm trying to find out how wide a rake and blade combo an L35 can handle. The tractor is 4 wheel drive, 35 horse power and fitted with tractor tread tires. The manual says it will handle a box...

I just got a price for a Kubota Loader TL720 cutting edge. The bolt-on, 60 inch, reversable edge was $320, including bolts! I must be living or pricing in the Old Days. I know you get what you pay for but doesn't that seem high. I'm checking with another dealer. Do any of you know of a quality...

Hi there. new to compact tractors - been shopping for a bit. What does everyone think about this tractor? Thought I was getting a deere but I find a lot more Kubota's out there '96 Kubota L35 TLB 35hp 1845hrs 5 out of 10 cosmetically- stored outside so some surface rust and paint oxidized...

I can't get the backhoe off my new L35. The top connection unhooks OK per the instructions. The bottom connection is weird. The instruction manual shows a mounting bar that you raise up until it hits a guide stopper. In the manual picture the bar is kind of small and would come out of the...

My gear shift lever has been a little tight for a week or so. Yesterday it suddenly loosened up & now the Tractor won't move. I'm hoping this is a broken cable or pin in the shifting assbly? The shift lever actuates 2 cables which go down to a small housing bolted to the side of the trans. I...

Anyone have a recommendation for a manufacturer that makes a Thumb to fit a Kubota L35 TLB? The backhoe on this unit is the BT900. Thanks.

:confused: My L35 has developed a leak in one of the hydraulic lines for the backhoe bucket. After disconnecting the line form the fittings, I find that I can’t get the hose through the frame by the boom cylinder connection. It is the fitting on the hose that won’t fit, I can cut the fitting...

I have a pretty ignorant question for you folks who may be familiar with this unit. I purchased the unit about a month ago to do some land improvements around my property. The tractor had no manual or documentation at the time. The dealer I purchased in from does have a service manual on order...

I found a 1999 TBL 35 with 1200 hours on it. Rubber is very good. It also has a clam shell for the front bucket (about a $4K extra) Service records included. Is $25K too much? Many thanks.

I would like to get the Kubota BT900 quick-attach backhoe for my Kubota L35. Any leads where I might find one? Thanks!

I would like to get the Kubota BT900 quick-attach backhoe for my Kubota L35. Any leads where I might find one? Thanks!

I recently bought a 1997 L35 with a 4 post ROPS & canopy. Front right post was missing & I would like to replace it. Dealer will only sell me a complete new ROPS b/c of liability issues. I would prefer to just replace the post in liew of having sombody fab one up. Anyone know of a source...

I have an opportunity to purchase a tractor that has been stored in my garage for a couple of months. It's a Kubota 4x4 L35 with TL720 FEL and BT900 Backhoe. I do not know what he wants for it yet but I've been considering a tractor to mow some horse pasture (10 acres) and do some land...

Hello, I am in the market for a small TLB that also has a small price tag. (Im the first one Im sure). I found a 1996 L35 with 2345 hours for 16k here in CA. Its the cheapest (and of course the oldest) I have found so far. Can some of ya'll give me your thoughts on this price tag? Looks good in...

Ok, I have sold my skidsteer and I'm getting ready to take the plunge and buy a TLB, either a L35 or B21. Looked at a L35 today with 1700 hrs, started up fine, everything ran well, FEL and BH were fairly tight, had a hose that probably needs replacing on the BH and it had some dings in the...

this tractor/backhoe looks pretty good, has 1500 hours, and the guy is asking $17,000 for it. that really seems high to me?? but what do i know..what do you think?? heehaw

Can anyone tell me how much bigger the L39 is versus the L35? Is the L39 frame size the same as the L35? Maybe one of the dealers who have seen the L39 can comment. I would appreciate your comments! : Jon

Is there a grey market version of the L35 TLB? I am looking at a 2000 L35. It has a serial number of 71137 (but I don't know where to lookup Kubota S/N,s). I am just a little concerned because the decals are off and there is no Operator manual. I saw on a list of grey market Kubotas a L33...

WHAT\'S A GOOD TRAILER FOR KUBOTA L35 ??? After looking at several different 10k trailers for my L35 I'm confused on which would be best. One thing I've noticed is that the axle placement on a 18' trailer varies from makers. In order to get proper tong weight I'm sure this makes a difference if...

Looking to purchase one of these but can find little feedback on the Bobcat. Any help

Question for RaT. Assuming a fellow didn't need the finishing mower capability, would the L35 worked for you instead of the L48? I think once I get my place parked out, the L35 would be a perfect size for my needs. Bush hogging and loading. Thx, David...

I have a neighbor who has a L35. I have an L3130 with loader and frame mounted backhoe. I'm in one of those "who has the bigger one" discussions. My neighbor claims the L35 is a MUCH beefier machine than the Grand L series. But to look at his machine and mine I don't see many differences...

Looking for anyone who has had experience or knowledge of bleeding air from the bucket circuit on an L35. My machine was built in 1999. It has about 900 hrs. and the bucket flops badly when trying to backdrag. I don't have a service manual but I believe there is an air bleed fitting somewhere...

A friend of mine was out clearing brush and noticed that the side of the 24in bucket was splitting. Upon further inspection we discovered that the other side was splitting the same way. It's amazing that it would fail this way. He is heading off to the dealer tomorrow to see what can be done...

Hello, Your advice is much appreciated on helping me make the best decision given the challenge of price vs. performance. I have 12 acres of land, mostly forested with trees 12" diameter or less. I'm on a ridge, so the land slopes gently to moderately on all sides. I reside in the Granite State...

Has anyone purchased or inquired about new L35 prices? If anyone has any price info, would you please post it!! Please include whether your price is list or out the door. Thanks......Jon

Hello, Have not been here in a while, we are STILL shopping for a Tractor.... Hubby had a problem giving Uncle Sam hundreds of dollars in sales tax, so we decided to look for a used Tractor. Of course every time hubby decides to buy the model we last looked at, when we go to buy we end up...

Hi I am a new member with a quick question.My Kubota dealer has been watching for a used L35 for me. I just checked out a 2000 with 166hrs. The bucket edge and backhoe teeth barely have a scratch. It also has a Curtis cab and heater. I was quoted what sounded like a fair price, does $26k sound...

I recently purchased an L35 Tractor/Loader/Backhoe with all the goodies (4in1 bucket, top-n-tilt boxscraper, 60" 3pt mower, and, of course, a 75 bushel manure spreader ! ! :-) It's like being a proud Pa Pa again...showing off to anybody who'll listen and look. Great machine! I've run heavy...

I've not noticed much if any commentary on similarities/differences between the two. Are they essentially the same machine with the L48 having the hydro tranny?? I understand maybe subtle differences in loader/hoe but those not withstanding, is the tranny the significant difference? If they...

Does anybody know what a reasonable rental rate would be for an L35 Tractor/Loader/Backhoe (new)? Per hour? Per day? Minimum charges? Thanks, Dave

Used L35 --- on sale 2200hrs Steve@carverequipment.com