mahindra 6000

Does the drain valve screw in and out, or does it just pull out. I have operator and service manuals, and neither tell how to open it. The manuals just say to open. It also says there is a second drain on the "left side of the crank." No idea where that on is to drain the block. Thanks

Hello All! I am new here and relatively new to tractors. We have a 2005 Mahindra 6000di with a ML260 front end loader/bucket. Recently the bucket started to slow when lowering. Raises, curls, and tilts normally but lowering very slowly. I removed the dry rotted rubber boot on the joystick and...

For starters, the only implement I generally run off the PTO is a 6' shredder. We've owned this 6000 for several years (purchased used). During that time, the PTO has occasionally disengaged seemingly randomly. Sometimes you could run for hours without issue, other times, it would disengage...

Greetings, My father in law is looking for a new tractor for his farm 160 acres in upstate NY. He currently has a small Yanmar LX590 ( I believe) which is too small for the task of lifting large round bales everyday and traveling to the fields. He will be keeping this tractor as a backup and...

This sounds crazy even to me...I've had this 6000 since new in early 2003....as you sit in the seat on the left side down and back from the "power beyond" lever is a second lever that goes into the trans/differential...To my knowledge, I've never used that lever at all...I've looked it up in the...

So this may be long thread but I need help diagnosing a problem and a little backstory may help. I poked a hole in radiator and didn't realize it until tractor overheated (temp gauge not working). Replaced the radiator and all was well. After about 15 hours on the tractor with a 10' bushhog...

I'm changing the hydraulic fluid and I'm having trouble removing the suction strainer pipe. I've removed the retaining tab and I'm able to rotate the pipe but I can't pull it out. What could be preventing me from pulling it out? :confused::confused:

Hello All, I recently purchased a Mahindra 6000 and love the tractor, but am having starter issues. When I got it, it was having a few issues starting. I bought a new battery, and it would periodically click at starter after the new battery. I ordered a new solenoid and it would start...

Does anyone know who manufactured the older (around '03) starter motors for the Mahindra "00" series tractors? Mine works fine if its above 40degrees, but doesn't quite have the guts to turn it over fast enough to start now that its about 6 degrees outside....the 6000 is a 195 CI 4 cyl direct...

I have been clearing large trees from my wooded areas. A couple days ago when I came back from lunch the tractor would not start. When I turn the starter switch there is no power to the dash or injector heater. The starter doesn't click or turn. The battery is charged and I replaced the...

Recently clearing woods and stopped for an hour break. When I came back there was no power to the switch. Gages are dead, no starter click even. I have looked for a few hours on the forum but no luck on finding a fix. I replaced the starter relay switch no help there. Fuses seen ok. any...

Question for the group - if I were to purchase an aux hyrdaulic kit from a dealer, how difficult would it be to do the install myself? I'm pretty comfortable twisting wrenches, etc., and would like to get a top/tilt set up on my tractor. It does not have a FEL or I could just add in there...

Could use some help. My 6000's clutch is getting harder to engage. It got so hard that I even had to pull up on the clutch after depressing it. After cleaning out a barn it got somewhat easier but the next day was hard engaging again. Thanks for any help I only have 800 hours on tractor and the...

Could use some help. My 6000's clutch is getting harder to engage. It got so hard that I even had to pull up on the clutch after depressing it. After cleaning out a barn it got somewhat easier but the next day was hard engaging again. Thanks for any help I only have 800 hours on tractor and the...

Can anyone tell me where the air bleed screw is located on the fuel pump? Mahindra 6000 2wd...

Can anyone tell me where the air bleed screw is located on the fuel pump? Mahindra 6000 2wd...

Could someone one give me the bolt hole measurements for a mahindra 6000 4wd? I have a 6000 2wd and trying to see if the loader attachment is the same for both. Thanks

Does anyone know if there's anyway I can make a ML 264 loader work with my 2004 Mahindra 6000 2wd? It calls for a ML 260 but I've found a very good deal on the ML 264. Thanks

Does anyone know if there's anyway I can make a ML 264 loader work with my 2004 Mahindra 6000 2wd? It calls for a ML 260 but I've found a very good deal on the ML 264. Thanks

Yesterday out bush hogging, I stopped and shifted into first to weave in out and around a few trees. Now it won't come out of gear. I can shift between high and low, the PTO and clutch work fine. I even tried reaching through the fill hole to see if I could pry it out of gear. No luck. I...

Good evening. I recently had a run in with a stump while I was bush hogging and it messed up the front power steering cylinder. After waiting two weeks to get one in, it arrived and this Saturday I installed it. I now have the tractor back up and running. The problem is before the...

I need to change power steering filter and fluid on a Mahindra 6000 4wd--series I. How do I drain the system. I have looked at owners manual and service manual and see steps for refilling and bleeding system, but none of the diagrams show how to drain the reservoir. I will also be changing the...

Could anybody that has a service manual for a Mahindra 6000 possibly send me the teardown of the power steering pump. Went out and were right in the middle of hay and can't wait to order a service book. Sure would appreciate it. Atbellbuckletn@aol.com Thanks.

Hi, I need to move my tractor and need to know the weight and also what size trailer do i need. Thanks.

I have a problem with air in my fuel system that causes the tractor to lose power and eventually shut down. We have tried bleeding by activating the manual pump and bleeding air from both of the relief screws on the filters. We can get the tractor running again for up to 20 minutes. Are we doing...

Looking for information on what the last digits make in a model, spotted a 6000 for sale but most of the ones on the forum have something in place of the last 2 zeros. does not having something mean that it is a stripped down model? Looking for some info on this tractor, it has a loader with...

Great combination!! Put her in 4th gear and let it go! Hay season is a great time of year.

My Mahindra 6000 2wd leak steering fluid at the steering column, right under the steering wheel. Any body have/had this problem before??? Thanks in advance for any infor on this.

Just a note on my '02 Mahindra 6000 4 WD.....no problems in the last 250hrs....yeah, I know, we seem to be listing Mahindras' that have "issues"...sorry, don't have any. How 'bout the rest of you Indian Mahindra owners that have no problems...time for little a different slant on these tractors...

Looking at a used (less than 200 hrs) 6000 (2 wheel drive) with MH loader. What is it worth ( please give a range from great deal to good deal)? It's in good condition. How reliable a machine are they? Would you recommend one? Thanks in advance.

Hi Folks, I was piling some brush this afternoon and my brake light came on and stayed on. My first thought was a wire had pulled loose under the foot board but didn't see any evidence of that. Any thoughts, ideas, etc. Thanks for your help.

It is time to replace my battery. It has an Exide 31 in it, but have not been able to find that battery around here. Have found Exide dealers but they don't have that battery. Always thought Interstate batteries were good. The top of the batter is some what worn off, but seems to be either a...

Has anyone removed their back rest on a Mahindra 6000? Does one take the trim off and then the pad to access the bolts or does one dismantle part of the seat adjustment mechanism from behind to access the bolts? A couple of pictures are attached.

Been pulling my 5410 Rebel baler with the Mahindra 6000 and it does a great job. Even on the hills it does fine, not even pushy. Would like to have a cab on it though. On a windy day the hay dust is ugly. It will pull it as fast as the baler can take it. Usually in low range 2nd or 3rd...

Just a note here...I woke up yesterday morning about 0630 with a pretty good pain in my stomach/abdomen area. I got up and the pain progressively got worse untill it was somewhere around an 8 on 10 point scale (to me a 10 being shot thru the groin--trying to keep it clean here...). Started to...

Hi all, I have asked this question before and I thought I fixed the problem but recently the problem reappeared. Ihave a 6000 2WD and recently tractoc acts like it runing out of fuel. The engine will mis and the does not how hard I push on the gas pedal, the engine will eventually dies. I have...

Some of you may be aware through other posts of mine that I have been working on changing over my 6000 pin on loader to a QA for months. I want to say a special thanks to Galen, who, although I did not purchase from him, really helped my through getting the right product. I got prices as...

Hello, I have been a long time reader on this site and a first time poster. I would like to thanks everyone for all the helpful info that helped me out countless times in the past with my 2002 6000 2wd. I have a question and hope someone can help me out. I have a 2wd 6000 and I would like to get...

Finally made my mind up and got a 2wd mahindra 6000 . .VERY pleased with my purchase.

I've been trying to figure out what tractor to buy for a couple of months and I cant seem ti make my mind up on which to buy. I have used dads old David Brown 990 for a couple of years and a Case 1190 to do all the work around the farm and it's time to buy a new tractor but what? I like the...

I've been trying to figure out what tractor to buy for a couple of months and I cant seem ti make my mind up on which to buy. I have used dads old David Brown 990 for a couple of years and a Case 1190 to do all the work around the farm and it's time to buy a new tractor but what? I like the...

I've been trying to figure out what tractor to buy for a couple of months and I cant seem ti make my mind up on which to buy. I have used dads old David Brown 990 for a couple of years and a Case 1190 to do all the work around the farm and it's time to buy a new tractor but what? I like the...

I have a 6000 that is having a problem pulling it's own weight in high gear. One of the helpers was on it a few days ago, and he said it just "quit on him". The problem only seems to occur while in high gear - in low gear the thing goes just fine, but of course its very slow. Also, the tractor...

Mahindra 6000 \"Music\" Electrical Connector The wiring diagram for my 6000 shows a 3-prong electrical connector labeled "Music." I've located a connector under the seat with corresponding wire color codes and voltage/switch status. It is a female connector capped with a blank. Anyone know...

I've got a new Mahindra 6000 and it "surges" at certain rpm's. That is, it doesn't hold a steady rpm but the rpm's go up and down about 50 rpm's. Anybody have this problem? It sounds like the governer to me but I don't have a service manual so don't know what to do other than return it to the...

my clutch is starting to slip again. only has 219 hours and tractor has not been abused, does mahindra make a shotty clutch assembly or what?

Sorry for the newbie question. I bought a used 6000 4wd with 200hrs and I'm not sure if I have clutch problems or not. When you depress the foot clutch should the PTO stop turning? Also when you use IPTO lever, should the lever stay up by itself to keep the clutch disengaged while you...

I sent 4 digital pictures of the 511 with the hydraulic tank/backhoe connectors to Mahindra in GA last nite. Got a call at lunchtime today from Bradco that the tank that Mahindra sent is not the correct one for the 6000. He gave me the correct part number. I called my dealer who was going to...

Well, I pulled the trigger today and ordered a 511 BH with both the 18" and 24" buckets and frame mount. Also ordered the PTO pump. Should be here in a couple of weeks. Anything I should be wary of????Anyone had any problems on break-in with the Bradco? thanks. BobG in VA

Saw a used Mahindra the other day and am struggling with the value. 4WD, FEL, a little damage on the front grille headlights, tires worn on the back sides(dealer says this is from running on pavement), was used primarily for contract grass cutting, approx 200hrs. 2002(?) model. With new...

There is a Mahindra 6000 4x4 in the classified section for sale due to divorce forced sale. It was bought last fall, FEL included. $18K. Found it this morning. IH3444

Almost time for my 50 hour service, any oil filter choices besides the dealer? Thanks, Chuck

Looking for recommendations for hydraulic system oil for my 6000. The book indicates I should use 30 grade non foaming mineral oil above 32 degrees F or 20wt/10wt below 32 degrees F. Anyone have any recommendations as to brand preference?

I'm considering a 2001 used 6000 2wd with about 450hrs on it. The chassis appears to be clean, but I did notice a little oil on the underside of the engine. When I crawled under it, there are a few small spots where the oil was forming a drop or two. The unit has been sitting idle for a while...

I just purchased a 10' rotary cutter made by Internationl Machine Corp. When I picked it up and they loaded it on my trailer, they told me it weighed 2400lbs. I was also told it weighs 1980lbs. At any rate, I had to load it long ways on my trailer for obvious reasons. It had all the parts...

I've been reading alot for a week or so. I am near pulling the trigger on the Mahindra 6000 2wd, 6' box blade, 6'disc, and 6' cutter. Package price after $500 rebate is $15,620, without any negotiation. 4500 is $13,520 (same implements). Kubota M4900 (same package, less HP) was around...

Mahindra 6000 Personal Review My Mahindra 6000 4X4 now has about 70 hours on it. It is equipped with a Front End Loader and it is used here on the ranch to do anything a tractor should be able to do and more. I have pulled portable out buildings and even pulled a friends Chevy 1-ton 4X4 out...

mahindra-ML-251794-ML- Moved to Mahindra Forum.

IF your looking for one ausome piece of equipment, put the Mahindra 511 (made by Bradco) backhoe on a 6000 4wd. Just got mine back and WOW! Very impressive. Speed control on the swing, two lock downs, on or off in a matter of minutes...and is it slick. It will take me a while to learn how to...

mahindra-ML-238683-ML- Moved to Mahindra Forum.

other-ML-238683-ML- Only non-brand specific and comparison questions should be posted here.

What is the going price for a new Mahindra 6000 4wd with a loader? Does anybody have a cab with their Mahindra? Are there any other frequently requested options which Mahindra offers? Do they make their own engines? I just learned that one of the local used car dealers is now the regional...

mahindra-ML-200551-ML- Moved to Mahindra Forum.

I have posted requesting information on the Mahindra 6000 4wd and some of you responded. Thank you. Today I purchased my new Mahindra 6000. I was able to pick up a demo with a few hours on it and 50 hour service already done ($500 value). It came with a fel, which is made by Great Bend for...

mahindra-ML-196571-ML- Moved to Mahindra Forum.

I am located in Ohio and looking for information about the Mahindra 6000 4wd tractor. I have owned JD in the past, but really like the Mahindra. Has anyone bought one? Loader? How do you like it? Problems? Price? Will it pull a 10 ft rotary cutter? Thanks for your help on any of these topics.

Looking for information regarding the Mahindra 6000. I have been looking at the Kabota M6800 and the JD 5320. I had just about decided on one of these when I looked at the Mahindra. Seems to be very well built, does not have all the niceites of the green and orange, but a good looking, very...