mahindra

I have a 22' Mahindra 1626 I just purchased on Wednesday. The only thing wrong with it is a little chipping paint on the rim that id like to fix. Problem is I can't seem to find the paint code for that grey for the life of me online. I was wondering if anyone had a paint code or something close.

I have everything but the front protective glass lens. Can't seem to find one. thoughts?

I have a 2022 Mahindra 6075 that has been impossible to grease the main loader pins on the loader. Has anyone else had the same problems ? if so what was the fix ?

Hey gang, my father has a KTST6 tiller that he's had for 7 years now and of course I'm responsible for the servicing. I'm trying to find a parts diagram / breakdown of the top gearbox. I need to replace the double lip output seal that Mahindra is calling a "non-serviceable part". It's leaking...

I’m hoping someone can tell me where the hydraulic filter is located on this tractor. It is Chinese tractor

Anyone give me some information on this issue? When one wheel is straight the other is turned. I looked to see if I could adjust the arms and straighten them out, however they are bolted straight trough with no adjustment that I can find. Also it looks like it would need to be adjusted in not...

l have a mahindra 4035 HST and don't know where to find the location of the hydraulic suction filter Can anyone help?

1526 not getting power to the solenoid wire on the starter, works when jumped across. Anyone seen or have a wiring diagram for this Tractor? Thanks!

Hi, I bought a Mahindra 1626 HST in May of 2024. I live In Central NY on the shore of Lake Ontario where we’ve been getting a lot of snow. Last week I was pushing snow around with the bucket, and the front Axle locked up on me. The tractor was in 4wD when this happened. When taking it out of...

Can anyone help identify the part number for a 2016 Mahindra 1526 Lower Dash Panel? marked in red in the pic. MahindraUSA site is junk and the dealership has the part listed at a price out of my price range. Where does everyone shop for Mahindra parts online? I have a 4530 and a 1526 and finding...

Any help with detail instructions how to do is appreciated. Under tracor I can hear clicking into gear same as fwd. Fwd works fine. So I feel must be inside trans. So must split tractor Instructions would be much appreciated Hal Woodville Tx

Shuttle will not go into reverse, fwd works Ok. From under tractor, I can hear reverse click as if going into position, just as same clicking into position in fwd. I feel I must split tractor to find problem. Hope someone can give some insite And step by steps to split tractor Thanks in...

I just bought a Mahindra 6075 and I have been told that the dry clutch should have a weep hole on the bottom of it and I can't seem to find it. The mechanic told me that I should drill one myself, but I'm confused because wouldn't Mahindra have put one in if it needed it? I understand that...

I have a Mahindra 4530 with a ML245 FEL. Probably made around 2010. One of the the bucket/tilt cylinders is leaking so I took it off and took it to have the seals replaced. The shop told me it wouldn't do much good to repair it because there is some pitting on the shaft and the new seals...

Looking at a 2022 Mahindra 5155 /<100 hrs. Is the 5155 made in Inda by Mahindra? Can owners give me the good, bad and ugly?

Just saw a Mahindra sale ad 1/22/25 0% finance 84 months $5k back

December 3, 2024, The local Mahindra dealer picked up my Mahindra 1126 tractor with M1160 Mid Mount Mower to do the fifty hour service. I had several other complaints about the tractor & mower. I had previously talked to the dealer where I bought the tractor and they told me that everything I...

I want to add a grapple to my 4035. If anyone has installed a WR Long third function unit, any input would be greatly appreciated. If possible, any pics you could share would be helpful too! Thanks much!

Hi everyone, I recently purchased a new house on 5 acres, and we’ve decided to invest in a tractor for property maintenance. After shopping around and visiting a few dealers, we’ve narrowed our choice down to Mahindra, specifically the 1126 and 2126 models. I’m hoping to get some advice from...

Today I was out leveling a piece of my property when all or a sudden my left front wheel came off. At first, I thought it might have been the lug nuts that came loose, and the wheel came off the rim, but when I looked at the inside of the tire, I saw a splined shaft still attached to the rim. I...

I have a 2019 Mahindra Emax 20s I bought used a few years ago. Has ran like a top until the other day. I cranked it up and started to back it under the shed to install wheel spacers on it. After installing them I went to start the tractor and move it back out from under the shed and it will not...

Have loosened/removed the retaining plate around my 2008 Mahindra 4110 rear brake boot (where the brake rod goes into the rear axle), but don't know how to "break" the rod apart to get the old boot off the rod and the new one on. Anyone done this and have any advice?

Need information on removing and inspecting drive shaft (from rear drive to front axle). Any and all information is appreciated. I suspect either shaft gears or collars are damaged. TIA

Seasons greetings all. Was swapping out my loaders bucket for my snowblade as is sop this time of year. Before doing so I flattened some small saplings to make room for snow movement in the event of some heavy snow fall this winter. I noticed one of the front wheels seemed to be...

Not really a comparison thread. But I now own both these machines. Just picked up a '17 3550 with R4's, cab, loader, 4wd ~600hrs Some may remember my quest a few years ago saying I wished a mfg would produce a tractor...HST.....with something larger than 9.5x16 or 12-16.5 front wheels/tires...

Make property management 10X easier with the Ultimate Rack®. Replace Your UTV / Pickup Truck - 600 lbs. load capacity + tow up to a 2,000 lb. trailer (With load on the wheels.) Doubles As A Ballast Box - Built with 300 lbs. of 11 Gauge Steel. Increase ballast up to 1152 lbs. with suitcase...

I am looking to upgrade my JD 3032E, mainly using it for logging / firewood with some brush hogging and trail maintenance as well. I built a log trailer to haul 10' logs out from the woods, it works well but the 3032E is definitely getting pushed past it's limits. The 3032E is certainly nice for...

Has anyone reversed the rear wheels on the emax 20 for more width ? If so did it make a difference, and is it recommended ? Thanks in advance.

My 3316 tipping cylinder is leaking and I was able to get the new seal kit but I am having trouble figuring out how to disassemble. The cylinder is a KMW 3150-2113 that does not have a gland seal that is threaded. There is a clip that can be removed on the outside and that is all. I found a...

This tractor is a 2016 model Not even enough power to pull itself up a hill . Wondering if anyone has had a similar problem?

I have a 2018 Mahindra 4540, with the Mahindra 4550=4L loader. One of the loader tubings failed this past weekend. Blew out the side wall of one of the tubing runs that run under the removable protection plate across the front crossmember of the loader. I thought it was 3/8" tubing but I was...

Does any know if you can put the Mitsubishi s313 from a 3316 in a 3510 that had a Mahindra 3A135? Thanks

Hello, Does anyone know where I can get a cab to fit my 2810? Thanks

well i finally got my tractor back this afternoon after 2 months - mostly waiting for glowplugs and gowpluge timer or some such thing. the driver told me that mahindra was boughten from the Indian manufacturer by some US company. anyone hear of this or have any details. He also said the US...

it appears that my PTO lever has disconnected from inside the PTO if anybody has any suggestions I would appreciate it. I pulled the cover on the side of the tractor and tried to remove the lever itself but it would not come out all the way but it's not engaging at all feels as if nothing is...

years ago i had an issue and tried my damndest to get the dealer to help fix or get the part i needed, and basically that was a 7 week joke. Too complicated to explain the whole scenario. so i ended up gettin a part from Bill.s in TX, cheaper and shipped for half price in 2 days shipping. 3...

Working on a friends tractor. It sat for a while and got water in the bell housing The clutch stuck to the flywheel , I assume it got hot, the throw out bearing is stuck and the fingers on the pressure plate were destroyed. Every single finger broke and scattered around the bell housing...

I have a 4540 mahindra tractor and I just put a new PTO oil seal in the rear and in about 2 hours it pulled out and I lost most of my hydraulic fluid. Anyone else having this problem? Would love some help on how to fix it. In the illustration its part number 20. I replaced the gasket and also...

Where on the tractor is the fuel Solenoid cutoff

I have removed the fuel tank filter from bottom of tank. I have replaced the filter from bottom of fuel primer. I have let out the fuel from the fuel tank, ran more fuel in/out of the fuel tank for a cleaning method. Added more new fuel in the fuel tank. restarted the tractor back up, again it...

I recently purchased this mower used, and I found some side play in the spindles, which may indicate they need to be rebuilt with new bearings. Has anyone on here ever rebuilt spindles on this model mower? They have a 4 bolt square pattern housing. A thin 25 mm slotted self locking nut is on...

Wondering if I can use Castrol UTF in my hydrostatic transmission for the transmission / hydraulics in my Emax 25? Manual says to use API GL-4 grade, 80w gear oil. Can't find these specs with the castrol. Thanks!

Anybody have one of these or know how they are performing as well as any problems. They look the part and have some great features.

Looking at the 1120, has anybody had one long enough to form an opinion. Local dealer only recently got some and has none of them out long enough to get any real feedback as to how they are performing. Dealer provides great service and mostly services larger farm equipment so no issue on that...

Anyone know where I could find an engine hood replacement for my 3505-DI?

I helped out my neighbor install 3 rear remotes. He bought a Stinger Attachments Grapple CCG-56 from me and needed a way to control it. He also wanted to add a hydraulic top link so I suggested going with 3 SCV's so he would have a spare for future use. We used 1/2" couplers as the loader uses...

I have a mahindra 2638 hst with around 500hrs on it. Tractor sat for 2 weeks. Went to start it and cranks but no start. Fuel filter was leak at the top by the gasket. Replaced that. Loosened injectors and bled air out. Tractor will run on ether and has plenty of fuel getting to the injectors...

I have a Mahindra 3616 HST tractor and I was using it to rip some dirt up with box blade and I put it in 4wd for this for the most traction and all the sudden a horn like beep noise came on it was solid only stopped once I turned the tractor off and all the warning lights on my tractor have been...

Thank you all the is my first post. I drove the Mahindra 3525 diesel tractor to dump some limbs, and it just started dying. I had to tow it back up and charge up the battery. It cranks good and there is diesel at the fuel rail, I drained them to check for water. I also checked the fuses, and I...

My Mahindra 2545 HST will not move under it's own power. Almost seems like the clutch went out. What can I do to troubleshoot this before taking it in to a mechanic and finding out I need a new clutch? It has 85 hours on it and I bought it a few months ago with 75 hours on it. I do not know...

Have a 2015 Mahindra, has 630 hours, clutch stuck but got it freed up. Checking into this further, found the plug in trans for condensation still in place. Hope this will help others to check that there’s was removed when tractor was sold. About a cup of water came out when removed

I bought a county line 3.0 auger attachment for my Mahindra 1538 l and was wondering how big of a auger can I use with this tractor. Any help is appreciated...

I been seeing auctions for Mahindra tractors auctions in Houston. Cab tractors, 70 horse, most selling around $20,000-$25,000. They are new, less than 5 hours, they have loaders. I wonder if they been in floods. I email auctions and ask but got no reply.

I hate the lifting arm on my Mahindra 2638. I whish it was longer so I could reach it better. I have read a post on how to loosen the tension spring and I plan to try that but has anyone ever extended the length of it to make it easier to use?

Looking at a 2019 mahindra 6075 with cab and loader. 2500 hours, dealer asking $25k. Good price? Things to look out for?

hey fellas, a few weeks ago I bought a new 5155 and in 8 hours of running it, the tractor performed flawlessly with a Mahindra Bush Hog. I mean it has been a beast. today I went to run and it started the PTO just fine and I was mowing about 5 minutes and noticed it wasn't really mowing...

I recently purchased a 2014 Mahindra max 28xl with 150 hours. New to owning a tractor. The front in loader is really slow to dump all other functions work fine. I purchased a gauge and check the pressure. All is at specs 2100. Now here is the strange thing I disconnected the dump hydraulics and...

I recently purchased a 2014 Mahindra max 28xl with 150 hours. New to owning a tractor. The front in loader is really slow to dump all other functions work fine. I purchased a gauge and check the pressure. All is at specs 2100. Now here is the strange thing I disconnected the dump hydraulics...

Anyone know valve clearance on mahindra 2415 tractor

I’m looking for the bolts and that cover when I bought it it didn’t come with it i need numbers or a name for it

MY Mahindra 4500 2wd primer not priming. Primer head will not pull up. Plus pressing the fuel paddle/rpm arm does nothing. What wrong???

I have a Mahindra 3510 3cyl, 34hp. After setting for a month we started it and it smokes out the exhaust and makes a loud popping noise near the back of the engine on the right side. It does quit smoking for a while the starts smoking again. Drained fuel and add 5 gal new with a fuel additive...

I think my transmission might be going out when I drive it for a while about an hour or two it just will not roll after that I appreciate it somebody give me some help

I'm pretty sure it's hydraulic fluid - It's not engine oil and it isn't diesel fuel. Seems to be coming from behind the plate. Tractor is low hours, I haven't looked lately but I'm guessing 300. Any ideas what it is and can I run it (while monitoring the hyd fluid level) while it's leaking? I'm...

i was using it to move some dirt and rock in my driveway and then i put it in reverse and it would not move i put it back into forward and it would not go forward either I've changed the Hydraulic Fuel and Filter and it still wouldn't go forward or backwards

I'm new to Mahindra. Just purchased a 3510 with FEL serial # Y03 so I guess it's either 2005 or 2006. When I got it home PTO worked fine. I removed the FEL for easier access and replaced all the fluids, front end, engine oil and hydralic oil. After all the fluids were replaced with the FEL...

I was drilling beans and had made a couple passes I started to make the next pass and when I dropped the drill the temp gauge went from normal immediately to hot so I quickly reached up to shut the tractor down it kept running a bit puffed black smoke and shut off. I got out and noticed fluid on...

Does anyone own a Mahindra 1126 sub Compact Tractor? If so, does it have the mid mount mower installed? Mule

Bought my 2538 HST CAB new in Dec. 2016 - on our weekend ranch (garaged) so gets very little use, so only have 110 hours I noted the other day. While changing the battery last Dec (2023) l noticed the A/C belt was shredded/gone, which explains why the A/C was not working. Since its not an easy...

Does the drain valve screw in and out, or does it just pull out. I have operator and service manuals, and neither tell how to open it. The manuals just say to open. It also says there is a second drain on the "left side of the crank." No idea where that on is to drain the block. Thanks

I'm 5'6" tall and have trouble climbing onto the backhoe on my Mahindra 4540. Does anyone know if there is an OEM or aftermarket step I could install to help me climb into the backhoe seating area?

Went to adjust clutch on mahindra 3505 di. Lossened 2 bolts turned the adjuster 1/4 inch completely lost the clutch. Tractor has a duel clutch system. I'm doing something wrong and don't know what it is. The adjuster rod would only turn one way counter clockwise and only 1/4 inch. Anyhelp would...

I have a 2023 Mahindra 5155 with FEL, Grapple, Bucket and box blade. Now I am shopping for a bush hog / pto style mower, for brush and other areas around my property that my Gravely ZT HD can't handle. Needs to be fairly robust, but no need for a forestry mower. What would you all suggest me...

Ideas needed. I have a 65hp Mahndria. I think it is the largest they make. Has almost 800 hours. Ran my mower/conditioner in the hay field for about three hours. I figured that I should put the rotary rake on it as I would be needing it the next day. Problem was the PTO shaft was so hot I...

I just bought a Mahindra 2538 hst in an online auction recently, and it was just delivered yesterday. I noticed the Check Engine light is on. I thought it might be because I found the plugs for the air intake indicator were unplugged. I also wondered if maybe the Check Engine light could be on...

With the topic of a STUMP BUCKET, is the FEL on the 5155 strong enough to use a stumb bucket, as long as you keep the size of the stump reasonable? I rented a Skid Steer (CTL) with a stump bucket and a grapple, and it was amazing. Thinking about a stump bucket for my 5155, but don't know if...

My floating vavle not working. Why .

Has anyone had any experience trying to get to the bearing on the hydraulic pulley out? We believe it is out. We are not sure how to go about getting to it what parts need to be taken off in order to get to it.

I purchased this from Mahindra Auction failed dealer inventory and I knew it had a few parts missing the dealer had robbed w 118hrs never titled. My hand throttle control roll dial is dead no response and i suspect they robbed a part. The foot throttle is working fine. I can tell the cover has...

The Mitsubishi diesel in the 3316 HST Turbo seized up at 500 hours. The tractor has been sitting at the dealer for nine months and they claim to be unable to get parts from Mahindra to rebuild the motor. Has anyone had any experience with a motor malfunctioning with such low hours? Can anyone...

My Mahindra 4510 loses transmission fluid regularly. As much as a couple quarts in a week or so. Cannot find a leak or a drip or a wet area anywhere, parked or running. Curious as to where this fluid could be going without a trace that I can find. Thoughts. Thanks.

It was delivered June 14, 2024 @ 3:15 PM. The dealer installed a summit third function. I am waiting on Mahindra to send the mid mount mower to the dealer.

Hello TractorByNet community! I have a 2016 Mahindra 1533 HST. I'm having trouble starting it. Beginning a year ago (roughly) I was unable to start it at all. After trailering it to the dealer they: Showed me where the manual pressure pump is and how to use it Replaced much of the fuel...

I am having a problem with the nimco cv 112 controller when I move the joystick left and right to control the bucket I get absolutely no respons at all and the joystick acts like there is no load at all on it.

Hello All, First Post here although I've lurked for advice many times. I've been looking all over forums and google to see if I can troubleshoot an issue I ran across last weekend and so far I haven't had any luck. I was Bush Hogging with my Mahindra 3016 and after about 5 hours the...

when i turn ignition on, you can here the glow plugs - but will not run over, no lights on dash. battery is fine -have cleaned and re-grounded; have checked safety switches; can jump start at solenoid but does not keep running. have power to ignition, no power to fuel pump, no power to stop...

It cranks fine but doesn't start. I tried to check the codes and have no communication with ecu using the factory scanner. I then checked for power and ground on the DLC, it was good. I checked continuity on all the dlc wires to the ecu and they were perfect so I replaced the ecu. Now the new...

I did something dumb, put too much load on my loader with the cylinders fully extended. I bent both of the lifting cylinders, to the point that they are spewing oil around the seals when they retract. What are my options here? I was going to see if I could get a generic cylinder replacement but...

My Mahindra 5500 was running as if it had water in the fuel (it had done this before). So, I emptied the fuel tank and put in new fuel. Loosened one of the injectors and turn over engine to pump our air. But the fuel pump is not pumping fuel. I checked by using the hand fuel pump that comes...

Hi! I would like to add rear hydraulics and controls for top and tilt. Tractor has a FEL. What do I need to accomplish this and where do I pipe (or) hose it too? Thanks in advance for any advice! Gary

Considering buying a Mahindra tractor. Any thoughts?

Hey folks need some help trouble shooting. Parked my Mahindra 3525 last week after mowing the grass and now it won't start. The battery & heating coil lights come on like normal but nothing happens when turning the key. The PTO is off and I replaced the battery at end of last season. Also...

i need to replace gaskets on the back of the fuel injector pump. Is there a special tool that I need to use to remove it.

2655 Mahindra for sale- 55HP with loader. 300 hrs total.Shuttle shift gear model. Cab with heat, A/C, Kenwood AM/FM/Bluetooth radio. WR Long 3rd function valve. Skid steer quick disconnect bucket. 45 HP at the PTO, which is independent and button-operated from the dash. Rear tire chains...

I am very interested in a Mahindra 1126 with loader and 60" mid mount mower. I am told that the Emax and Max series has been discontinued. I went looking to possibly buy an Emax 20s. It did not make me happy because of the rocker pedal for the HST. My right ankle is not flexible. My gut size...

I am attempting to determine if my eMax 25 has a vent plug. I can find no reference to one in the owner's manual. If there is a vent plug where is it located? Any advice would be helpful and appreciated.

Does anyone know the clutch adjustments for a mahindra 2525? Just replaced drive and pto clutch plates and need to know clearances. Thanks

The 3 point lever has been getting progressively harder to move over the years, now requiring dismounting from the tractor and pushing with two hands. I sprayed what I could reach with some PB Blaster lubricant, but even then I ended up bending the lever pushing too hard on it tonight. There...

Hi there Gents, Helping my elderly neighbor out with his 4550. Bought a service manual, but the electrical schematic page is illegible as it's tiny. Can anyone help me out with that? That being said... Tractor does not charge. Alternator is good, but my experience tells me there is an issue...

Hooked up the backhoe attachment on my Mahindra 1538L tractor today. It worked just fine for a minute or two, just long enough to begin to position it for the mechanical connection. Before I got it lined up to put the pins in, I lost all hydraulic pressure to the backhoe. I’ve verified fluid...

i got a 2018 5570 2wd the brakes are dragging when you push down the brake peddle you can hear the brakes sqeaking real loud like metal to metal and when i push in the clutch the tractor just stops by itself it sat up for a couple years i tryed driving it in reverse and forward and they just...

I have a great 2016 2555 with 250 hours. I am looking for a backhoe for this machine. OEM at the time of manufacturing was a Model 75. Of course none of those around. Curious if any owners have any luck with aftermarkets on this tractor understanding if it doesn't match the subframe it...

Unfortunately, it had a low coolant meltdown engine locked. Electrical- main fuse blows instantly when key turned to ON. Have removed all other fuses, still the same. What's next?

Last year I bought a used 2015 2565 and the AC wasnt working. The dealer was nice enough to replace the expansion vale (2 times) and the compressor. However, the AC still does not blow below 60F. I called them back and asked the tech what was done to the tractor and he mentioned they flushed...

Inherited my Dad's 3510 had it serviced. Should've asked them if it is full time 4x4 and what the shift patterns are on the two shifters. It seems to not pull with the front axle.

Hi everyone - this is my first post here, I hope I can learn from some of your knowledge! My wife's most prized possession is her Mahindra eMax25L HST. About a week ago it started blowing the 40amp fuse that is in front by the battery and radiator when we go to start it. We've been through half...

Finally finished, barely fit even with their smallest option the Single BOGL, will test it in a bit Used a diverter kit from Artilian.

Hello, just joined. I recently traded my 1982 Kubota M4050 for the 2002 Mahindra 5005 with a ML214 Loader (plus a few $). Had the Kubota for a few years and did a good bit of work to get it right, but it was long in the tooth (3,500+ hrs) and did not have a loader. The 5005 popped up from a...

I've searched a lot, can't find if Mitsubishi S3L2-Turbo has iron or alum head.

I was moving some logs with the grapple and i went to raise the FEL and nothing. All other functions work as normal but when i pull the control back to raise it doesn't raise and feel very limp. I took the cover off of the controls and it looks like 2 cables going down under the tractor to...

Hello tractor peeps, I have recently purchased a non-US sold Mitsubishi MT25C and was on the hunt for some manuals to be able to figure things out and get some stuff hopefully fixed. I decided to scrub the interwebs and figured "Well, it's a Japanese tractor and it wasn't sold in the US so I...

Have a 3016hst using it the other day getting garden ready was running fine went and put fuel in it and shut off, once done fueling went to start and acted like battery was dead, tested battery and it was on the weaker side so replaced with new, still the same thing maybe crank one or 2...

Howdy I have a 3550 and the throttle slowly lets off while driving so have to continuously give more throttle then lets off slowly or have to hold the lever to correct speed. Any idea where to start to correct this thanks

Is there a lever for the locker i keep hitting or is it mechanical and locks when it feels spinning?

I have been working on and off on my Mahindra 2555 for months now. I had a bad knock and a lot of white smoke. Could not determine the problem. Finally, this week I removed the engine and found that cylinder 2 and 3 the connecting rod bearings were totally gone. Cylinder 1 was fine. To my...

Good afternoon everyone, I recently purchased a Mahindra 5500, the tractor will only start and run by bleeding the 4 injectors. Once you crack the lines and bleed the air it starts and runs like a dream, I haven't hooked anything to it to do work with, but it seems to run fine with no lack of...

New member here. I’m trying to diagnose a glow plug circuit issue. My glow plug light only comes on for 1 second before it goes out regardless of what the coolant temperature is. I have the service manual for the tractor but it’s not very helpful. It says it should have a go relay, gp timer and...

I have a 05 Mahindra 3505. Looking into the wiring friar it shows black, red, and blue wire going into a “e.t.g.” Can someone explain what a etg is? I searched all over the manual and it does not explain

I was using the loader to move gravel the other day and the tractor stalled out. I tried restarting it, but it would not turn over. The starter was turning, but it would not catch. Since it was close to dark, I left it where it was in the yard. I went out this morning to try to get it to...

I am a dealer in the Northeast. Currently I am a Yanmar dealer (great machines, but not great dealer surport from Yanmar). I also have my Bad Boy mower dealer pestering to bring on their tractors. I am opening a new store around 30 miles away in which I would have access to bring in a new...

I have read a lot about greasing the bucket on my tractor… I have been told you can’t grease it too much when using the bucket pretty much exclusively with my current project - what are others thoughts?

Hi all: I have a 2615HST that is as dead as can be. It's likely a wiring issue, but I don't have a manual or a wiring diagram. The issue is that even with a freshly charged battery, nothing happens when I turn the key. No dashboard lights, no solenoid clicking. Nothing. I've looked for...

Mahindra Max-24 This seems a silly question, but I am missing 2 bolts that hold down what appears to be a spring-tensioned-band, located underneath the seat pan cover plate, and behind and above the rear PTO assembly. The band when unbolted sits at a 45-degree angle and requires a bit of...

2021 Mihandra EMAX 20S with only 87 hours - the Joystick lever is already stripped and came out into my hand!!!! Has anyone else has this issue?

I have Mahindra 475 DI and when driving below 900 rpm it starts to have problems, the rpm is unstable and the tractor have uneven power, the tractor shakes forward-backwards forward-backwards, but the engine works fine when tractor is not moving( it sounds like problem with delivering fuel when...

I wanted to do a write up of my experience with my 2021 Mahindra 4540 here on the forums to hopefully give other owners who may be Googling the same issues with their tractor. The General Situation: If you haven't seen my other posts, I purchased my 4540 4wd FEL in October of 2021 brand new. I...

Buy an Ultimate Rack Combo and Save $300! Our best selling Ultimate Rack Combos just got better! Order a combo and enter code: QH2023 at checkout to save $300 off your order, we'll even throw in a free 5n1 Tool Holder! That's over $500 in savings when you include free shipping ORDER HERE .

Hey folks, pulling the trigger on my tractor in March. That's when I'm actually moving onto my land. I've narrowed it down to the Mahindra 5145 Pros: -Heavy heavy tank -400 pounds stronger loader -Test drove and really like it -4 dealers within two hours Cons: -Shuttle only -MCRD -ECU ran...

Next summer we are planning on moving from south Georgia to Maine.. yes, Maine.. yes, we know, it's cold there.. lol... We bought 26 acres off-grid and I will need to do a lot of clearing.. making roads.. a lot of digging.. fel work.. grapple (trees, limbs, rocks) and snow plowing as the...

Hello, I am new to tractors and have just purchased a used Mahindra 5500 with a bit less than 500 hours on it. I'm trying to figure out what all the gears and knobs and pedals do and it would be very helpful if someone had a manual for this series. I can figure out how to go backwards and...

I purchased a Max 26 without the belly mower. I will get a 3pt finish mower for it. The dealer said the recommended implement size is 48" for basically everything except a rake. I find it hard to believe this 26hp machine can't handle at least a 60" 3pt finish mower. Does anyone have real world...

We almost never have any discounts/coupons/sales, but heeeere we go! www.(Temporarily blocked due to reports of company closure) Travis

Hi. Just recently bought a new 2022 Mahindra 5155 4x4. I’ve put 12 hours on it so far. About 1 out of every 4 reverse shifts on the synchro lever it kicks out of gear and horrible grinding sound. Hasn’t done it in forward at all only reverse. I messaged the dealer I bought it from and he says “I...

I have a 2005 TYM HST330 which has mostly served me well. Made by TYM, it was also sold as the Mahindra 3510 (so you Mahindra owners might have a suggestion here). I bought it used in 2010 with 191 hours on it and recently passed 700. It has an SCV (secondary control valve) and its control...

All-- I have a Mahindra 5545, 4wd. Today, it ran very well earlier, but when I started it to do a little backhoe work it began smoking from the exhaust and running very rough and would not produce any power. This happened a couple of years ago, as well. Back then, I had made up my mind to haul...

Ok I wanted to write this up partially to inform others as well as to vent a bit with this experience. First as a Disclaimer, I have had no problems out of my Mahindra for the 50hr I have owned it. I have been used to running various JD compacts and the main thing I realized about this tractor...

I just bought a Mahindra 4540 a couple weeks ago. We have about 17hrs on it. It blew a 40a fuse after about 15hrs. Blew it again a day or two later. Now at it’s blowing just about every time we turn it off. The dealer we bought it from said to just swap the 40a for a 60a. We didn’t feel...

I recently got a pretty good deal on a Mahindra 3525. I want to add a backhoe but can not find what backhoe to look for or if it is even possible

I have a 2017 Mahindra E25. My water pump has been leaking for a bit now and I have one on order. So up till now I have just been filling the tank with water before I use it and it would get me a few hours of use before getting too hot. I was using it the ither night and it got hot on me and...

Probably a dumb question, but where is the main engine oil dipstick located on an older model Mahindra 4500 2-wheel drive tractor? I've looked everywhere for that sucker. thanks in advance.

Hello, Mahindra 1533 HST won't start, sounds like it isn't getting fuel. Turns over strong. Please see video linked below. I'm trying to highlight that when the key is in the on position, the relay shown makes a buzzing sound but I'm not positive if it is abnormal. Also, the temperature gauge...

Is there a trenching bucket compatible with the 60B backhoe on my 2638 HST? thanks Keith

Mahendra 4035 shuttle won't shift out of neutral unless transmission is in neutral. And, transmission won't shift out of neutral if shuttle is in forward or reverse. Any help would be appreciated. Thanks, Jeff