Hello, I was curious if anyone could help me find a repair manual or give me some instructions on how hard it is to fix a leak in my hydraulic system on my Kubota B7100 HST Diesel. The leak...

I recently had the chance to purchase a 1993 B7100 HST with a 60" deck and its my first time owning a Kubota. The tractor and mower run great, but I discovered a fuel leak that appears to be...

The hour meter clicks on the one second slot, but non of the other numbers change. It would appear I have power and that the meter is bad, any thoughts. A new one is 100.00 thinking of buying an...

what is a good rough cut rear mower deck match for a B7100 4X4?

My B219 loader seals were leaking so I bought the seal kits. I had previously replaced the seals on one of the lift cylinders and all was good. This time I needed to replace;ace the seals on the...

Hi all, does anyone know the approx price for a front driveshaft for a b7100 hst? I've found one online (tractor) for 3k aud but it needs a front driveshaft, and I was considering purchasing it...

Need help replacing fan belt on Kubota B7100 tractor with loader attachment. Can't seem to move PTL cylinder in order to reach fan belt pulleys.Help!

I have a B7100 HST tractor, I found a belly mower about 3 hours away, before I go, I kind of would like to know if this mower fits the Kubota B7100 ? Are the mower blades are driven top most...

As per the thread below, I ordered new filters, oil and O-rings from Messick's and began cleaning/replacement today. When reinstalling the smaller filter/strainer, the thread jammed about three...

A little history. My dad loved gardening and used a TroyBilt roto-tiller until he just couldn't manage it anymore. He then bought a B7100HST package from a rental yard; it included a front...

Have a Kubota B7100 can’t get the 3 point hitch to go up or down it’s stuck in the up position

I just bought a b7100 for a really good price that was being sold as a non runner for parts/repair. The pervious owner inherited the tractor and couldn't getting it running so he decided to sell...

So I bought an old B7100, wanted to flush all the fluids. Removed what I thought was a drain plug and it was actually a stop plug for the hydraulic control valve pump and then the bolt (plug)...

Hi. I posted this in the Kubota owning/operating section but it might be better suited for this forum - I’m putting a 304 loader on a B7100. The LA304 loader is rated for 4.4 GPM@2000psi. The...

The LA304 loader is rated for 4.4 GPM@2000psi. The hydraulic pump on the B7100 is 3 GPM and supposedly somewhere between 1500 and 1700 PSI. I only plan on using the loader for yard work, snow...

I have a diesel fuel leak where the fuel goes into the engine. How to take this apart and what do buy to seal the leak? I have the original shop manual, but it isn't much help. Picture attached...

Hi. I’m trying to shoehorn a la304 loader onto a B7100. If anyone has either a b7100 with a loader or another tractor with an La304 loader, I could really use a favour. If you could post a...

Hello I have (i hope) a pretty simple question. Where can i find the productionyear of my Kubota B7100D. Its not on the identificationplate. Greets NIels

Hi folks, This may have been covered elsewhere so forgive me if so, but I want to share an experiment I am doing. I have had trouble with my 1980's B7100 HST overheating when I'm cutting heavy...

The three point hitch on my B7100 will not "feather" when raising. As I start to raise the lift handle, it makes an awful noise (like a dead-end hydraulic circuit) until I pull it to the full up...

I ran out of fuel in my kubota not the first time. I have successfully bled it several times over the years. After that I couldn't get the tractor to run solid. I thought I must have filled with...

I'm replacing the dynamo (if I can ever get the lower center nut off, then back on), and the coolant comes out of the engine in the same housing. I'm using a new gasket and I really don't want to...

Hi all, I have a Kubota B7100HST-D 4WD with a mid-deck rotary mower RC70-71H. Three blades with the two-outer driven by a single belt and the central one off the gear box. For the past 10...

*please help* Hello all I have a Kubota B7100D that had a bearing go out in transmission. I bought the tractor already partially disassembled by previous owner. After repairing the damaged...

In a couple days I値l be picking up a new to me B7100HST with a FEL and 1800 hours on it. They are asking $6000.00 or $6500.00 with a rear Woods 48 finish mower. Is the rear finish mower worth...

I have a B7100 manual shift 4WD that needs a front axel assembly. This is an older unit -- early 80's Anyone recommending a source for parts? From Kubota locally they would be about $CAN 3,000...

My Kubota B7100 HST does not stop when releasing the pedal when going forward, I have to push the reverse pedal to make it stop. In reverse it stops as soon as the pedal is released. Is there an...

What are the advantages and disadvantages between the b7100 with and with out the hydrostatic transmission models. I have someone that want to trade me a b7100 non hydrostatic for my 53 chevy...

I am preparing my 1994 Kubota B7100 HST for sale (within the next few weeks). I am the original owner and have taken good care of it. It has complete documentation, original bill of sale, owners...

Have pre-80 B7100 with a loader and pto pump. Pump drive shaft has 2 'chain couplings', one at each end. Can these be removed without removing pump itself? Are they available?

Can anyone recommend a bracket that I might be able to retrofit onto a B7100HST that would accept the M8071 weights? I have 1000# of these M8071 weights and so I'd rather use two or three of these...

Ive got a new to me kubota b7100hst-d serial number shows 90-91 but the seller says it was a 95 model year. Anyway Im pretty sure the hydraulic pump is 1700psi at 3gpm. I really want to run a...

It's a long story. I'll keep it short. I've had trouble attaching implements (mower) to this pto for awhile. Last time we used force (tapping hammer) to get the mower attached. Anyway, it went...

I have a Kubota B7100. I was hooking up my 4 ft woods rotary mower and noticed there are (2) locking grooves on the tractor PTP shaft. One groove is about 1/2" from the end of the shaft and...

Hello I just joined the forum because I just bought my first tractor - an older B7100 hydrostatic 4x4. I don't even know what year it is yet. I have a couple of questions. Are these prone to...

I stupidly put gas in my Kubota and ran it about 45 minutes. I caught the mistake, drained the tank, removed the fuel element. I will be bleeding the lines, injector pump and injectors. The manual...

I have a Kubota B7100hst 4wd this tractor runs but the water pump is no good for 5 yrs this unit was held up in a court battle that was recently resolved. the tractor itself was not the issue it...

I posted this in Parts/ and Repairs but figured I post it here in the Kubota section too. So I changed out the head gasket on my b7100. Getting everything back together and need to adjust the...

So I changed out the head gasket on my b7100. Getting everything back together and need to adjust the valve clearance. Hope I’m getting all the terminally right. I understand how to actually...

Would anyone know what Hyd. pump would be the best for a front end loader we are fabricating for a B7100 Kubota

The tractor is the later style b7100, and the pump I am refering to is the engine mounted hydraulic pump. I have afront end loader. The loader is a woods dual. I put a pressure guage on the...

My B7100 hydraulic implement lift has stopped operating. The check rod on mine is broken. Can anyone show where this should connect to? Ive seen drawings where the control or check rod connects to...

Can it be done?

I just picked up a 1980 B7100, and am starting to go through it. When I bought it, it was known to have oil in the coolant (or something turning it black). I've noticed quite a bit of smoke coming...

I am trying to find a replacement part for the control valve operating my B219 loader on my gear driven 4wd 1978 Kubota B7100. The detent cap for the bucket float valve has sheard off and a...

Hi, my Kubota B7100 HST lost all drive and I found that the input shaft to the HST has a stripped spline where the driveshaft from the motor connects to it. That kind of ruined my day. Can...

I recently purchased a B7100 with a woods DUal 145 loader installed. I have lately been using a pto powered wood chipper for about 2 hours at a time. When I finish using it, the hydraulics seem...

HI folks, I just bought my first tractor for our 5 acres.. A b7100 4wd It has seen a LOT of neglect.. It came with a box blade and bushhog though for 400 bucks. So anyway IT didnt have a starter...

Hi all, I own an old Kubota B7100 and need parts for a damaged front wheel. The local dealer has given me a quote and it's really quite high. Does anyone have recommendations for an online used...

I bought a Country Manufacturing Inc 8500 2 ton dump trailer. I have one remote on my L3540 and need to find out how to hook up a remote on my B7100. All I have is the operating, parts, IT and WSM...

I am wondering if anyone has mounted an rc54-24b mid mount mower on a 90's B7100HST 4x4? Will this mower work on this tractor or does it need modification?

Hey guys. Discovered a small leak in my recently purchased B7100's radiator. The fins are pretty beat in several spots, and I figure it should probably just be replaced. Called a local kubota...

I've been keeping an eye on these for a year or so and price is probably in line with others. I think I've seen the tractors alone for 3000-3500 but this one may be in nicer shape, and if you...

I hate to be the guy that makes an account on a forum just to ask, but I'm agonizing over this decision and I'm looking for input. My Cub Cadet LTX1045 has become more trouble than it's worth...

I hate to be the guy that makes an account on a forum just to ask, but I'm agonizing over this decision and I'm looking for input. My Cub Cadet LTX1045 has become more trouble than it's worth...

I have a Kubota 7100 with manual transmission. The tractor make a very loud whining and screaming noise whe trying to use it. It will sit and run perfect but only when you try to move does do...

Hey guys I have an Old 1994 B7100HST 4x4 runs and works great just no FEL so after searching high and low for one built specifically for it I finally gave up, but came across a set of D100 loader...

I need to replace some hoses on the 1630 loader on my '92 B7100HST. The ones from the loader valve to the hard lines. Does anyone know the size and thread? Last time I replaced hoses I took the...

Have a recent purchase of B7100HST-D and in checking the fluid level's .The hydraulic dip stick shows no level of fluid. have looked all over and find no plug that can add fluid. on top of...

As I was researching my first tractor, I just found out there's a 1990s Kubota B7100 HST 4x4 already in the family that I can probably have for free. It's in decent condition, but sadly it...

Hey folks I just picked up a '93 Kubota B7100HST (4X4, 16 hp) and will be needing a rear mount snowblower for it. According to the owners manual the recommended max weight of the blower is...

My 1984 B7100 HST started fine, my son hooked up brushcutter and brought it to shop to grease it up. Afterwards it wouldn't start. Sounds like a weak battery. We tried different battery, jump...

1st time using my PTO.. attaching a woods mower on a Late 70s early 80s Kubota Gear driven B7100. the PTO is grinding when I engage the lever to raise mower attachment. The lift motor does work...

Hi All: I recently completed an overhaul of my B7100. The tractor was not running when I bought it, so I knew there was some work ahead. I recently completed a full rebuild. When dismantling...

Help so my b7100 has a few issues. First as soon as its put in gear it trys to go forward just a little before any forward or reverse is applied. Second low gear used to work the first day i had...

Hi all I just bought a very old Kubota B7100 HST it was used as a golf ball collector at a driving range so I don't think it was used and abused but probably neglected. The motor is super clean...

Hi I am looking for a Kubota B7100HST PTO shift lever. If you have one or know where I could acquire I would be most grateful. Thanks Dylan

Hi I was wondering if anyone knows if the front drive shaft out of a Kubota B6100 would fit into a B7100. They are both gear shift models.

Hi, I have a B7100 HST and it is a thermosiphon type, 5000+ hours, I lost the first hour meter.... I guess I blew the head gasket about 3 years ago, and figured it out about a year ago, because it...

Hello everyone, Im posting this for my dad, we were doing snow removal over the weekend and he noticed that the pedal was doing some sticking. It didnt matter if he was in forward or reverse. He...

I took my starter solenoid off to clean up the wiring and can't figure how to engage the little hook on the end of it's arm back into the starter housing. It looks like it should grab onto the...

Hello I have an older (late 70's I think) kubota B7100 with a manual transmission. I have found a great deal on a 1640a loader that was on a B6100 manual transmission. Does anyone know if this...

Hello I have an older (late 70's I think) Kubota B7100 with a manual transmission. I have found a great deal on a 1640a loader that was on a B6100 manual transmission. Does anyone know if this...

hello all. i bought a b7100 long time ago and i thought it had a b1630 loader because of the manual that came with it. well on the tag on loader it says b-219.i need to replace all the cylinder...

Hello, I have two questions, one has anyone had significant trouble with their Kubota B7100? and if I want a little bit bigger tractor, what do you think about an International 350? Jay

I don't have a manual. I have removed the radiator, fan, and all the bolts and nuts I can see. Is there another nut under the left side of the housing (right side facing the engine)? If so I...

Hello folks, Im new to the form and I am looking for some info on my 1979 B7100. Ok it seems that I had a bearing that went bad and locked down the gear spur causing it to break and come through...

Hello, I have a 1994 Kubota B7100 HST 4x4 with a Woods DuAll 145 front loader. It also has a 7 ft back blade and a middle buster as attachments. 17hp 3 cyl diesel engine with 1300 hours. Mid and...

I have an 80's model Kubota B7100, about 2800 hours. Coolant is looking brown and ugly. Today it was boiling off overflow as I drove slowly using brush cutter on heavy, tall field (I worked it...

Hi all! I just bought a very old Kubota B7100 with loader and rear weight. Unfortunately I don't think its 4WD or diff lock are working and the rear tyres are virtually bald. So I have a tractor...

I have a 1995 Kubota b7100 HST. it recently started leaking oil. Unable to tell where leak is coming from. oil is on top of drive shaft housing, behind oil pan. Anyone have any ideas how to find...

I have a B7100 4wd and 3 point linkage will not lower whilst engine running but lowers very slowly when engine not running. Lifts ok as always and oil levels all check out ok. 4wheel drive ok...

I have a 94 B7100 with FEL that I've had for a few years. I've never put much on the back other than a hitch basket and the 3 pt lift has always worked intermittently. When I bought a brush hog...

Hi, want to mount hyd supply to rear of tractor, running from diverter valve, any ideas?? mickuk

Hello to all. I am new to all of this, with a 1980 Kubota B7100HST on five acres. I hope to learn a lot.

Anyone know of any backhoes that will fit a Kubota B7100? I am looking for back hoe with sub frame, not 3-pt.

I know I am looking for a needle in a haystack, however I think this is the best forum to find what I need if it available. I am looking for a Kubota back hoe model B/L 4520B or B/L 4530B and...

I have read many articles on float positions of 3 PT hitches and all are enlightening. I have a Kubota B7100 HST. When using box blade to move soil or level areas I continually leave piles of...

Hello. In my Kubota B7100D i had knob with the print "pull to stop" on the right side. A black triangular knob It was fitted under the "off-handle" around next to the battery. But i lost it (it...

My Kubota quit being diveable in any gear or range in both 2 and 4 wd, hi or lo range, but the Pto shaft and the TPH still work WTF?? :confused::eek::confused3:

My Kubota quit being diveable in any gear or range in both 2 and 4 wd, hi or lo range, but the Pto shaft and the TPH still work WTF??

On a Kubota B7100 HST there are 2 holes on the lower link arms where the lift rods may be connected. Which hole should the lift rod be connected to? Does it make a difference in the operation of...

Greetings all, I have a number of things I want to run by those who use or have used these tractors. Previously I had been contemplating a larger B2910 for my property which would be overkill for...

Ihave a Kubota B7100 with 4x4 and HST. We have only 4 acres and I love the little tractor but have had no success, really, in using my 4 ft box blade. The blade travels up and down as the tractor...

Thought the job would be easy - NOT! Took the Right Rear Wheel, Hub, Fender, Brake, and Axle Case off Relieved the fork and clutch dog gear to be in great shape - The diff case tabs are the...

Hello I have a question i hope someone here can answer. We have a B7100, and we bought that Kubi (thats how we call him) new in 1978. Its a very fine machine, almost unbreakable. But we miss a...

Hydro foot pedal won't go back to neutral without help. Does anyone know if this is spring loaded ? maybe a lubrication problem.

I have an older(about 1986) model Kubota. It needs a cab and heater for winter snowblowing. The work is now in process at a fabrication shop. a number of problems are being solved: 1.No easy entry...

does any one have paint alternatives for the Kubota orange I believe it is kubota orange not the Kubota 2orange

I use my B7100 a lot in the winter to plow snow. Last year was especially cold and I finally broke down and bought a golf cart enclosure as shown in this thread...

I have a 7100 HST and the hydraulic pump is kaput, I want to replace it but the dealer quoted an exorbitant price. I think he wants me to buy a new tractor... I am an 80 yr old stubborn B and do...

We get a lotta snow here, My previous blower was a BERCOMAC on a 650 KAWAI 4x4 ATV. It is not satisfactory, so I picked up a used B7100D with a rear blower and a front blade. :cool::cool: I am...

I have a Kubota B7100 HST 4x4. I have a front blade set up that I can move hydraulically, and I also have a rear brush cutter. I am looking at a mid-mount mower and wondering if I need any special...

Where could I get a replacement mowing deck for my Kubota B 7100 tractor?

I am trying to rebuild the hydraulic pump on my Kubota B7100. I have the pump off but do not see an obvious way to extract the outer bushings. I don't want to start prying and damage something...

What is the correct replacement size for the mounting bolt and nut for the Kubota B7100 HST?

Hi all. Recently had the opertunity to test out a 1978 B7100, 4x4 with factory FEL and backhoe (factory frame mounted) for a day. It's got 4000 hours on the meter. Some slop in the pins, but no...

Hi everyone, the tube that protects the driveshaft from the gearbox to the front axle as long since rusted away, except for about 3". I have some pipe and it is the correct diameter, but I don't...

My B7100 HST is equipped with a hydraulic diverter valve to switch the hydraulic flow from the internal 3-point hitch cylinder to an external use. My question: is this port live or is it...

Looking for the main cylinder lift mount that attaches the the front of a b7100. Part number 70010-00090 no longer available. If you can't part with one can I get a picture of one with some...

Anyone out there have a front lift mount for a b205 Dozer blade? The part number is 70010-00090 and is no longer available. It attaches the main lift cylinder to the front of the tractor. If...

I am looking at a 1983 B7100HST-1300 hours with a belly mower. The owner said he has problems when trying to engage the mower. it makes a grinding gear noise. I talked to a Kubota service mechanic...

Hi All, This is my first post and I've searched the forums and was unable to find an answer. I have several downloaded manuals for this 1994 tractor and all seem to indicate that the front wheel...

Where can I find a schematic for the transmission breakdown on a kubota B7100 4WD

Where can I find a schematic for the transmission breakdown on a Kubota B7100 4WD

OK i have another one for you guys! We have a Kubota B7100 in the shop, the FEL is plumbed through the 3 point lift cylinder assembly. The loader only works when the 3 point raise lever is in the...

Can anyone help? I have a b7100 kubota that I purchased about 6 months ago. The 3 point worked great when purchased but now only lifts at a very low idle. Any throttle at all and it just...

Hi, My B7100D is grinding the gears when shifting from neutral in any gear. It does not grind them when going from one gear directry to another. I have adjusted the clutch and I believe it works...

Helping the neighbor replace the clutch plate, pressure plate and throwout bearing on his B7100D (manual trans) The old friction plate went to pieces. The pins that hold the spring center to the...

Was just curious as to how much it would cost to go through and rebuild a 1981 kubota b7100dt both engine and transmission wise. The tractor does not need a rebuild but just wanted to see if any...

I just got a 1984 B7100 HST. It has a left foot pedal for clutch. What is the purpose of this pedal ? HST is just push pedal fwd & Rev. Also, HST is a bit noisy. Not a grind or metal on metal...

Saturday a man told me he'd sell me his storage building and his B7100 and priced them to me. I said I'd pay his price if he got the B7100 running and moving under it's own power. He has left it...

I have a B7100 with scraper blade and 6 foot trencher. The tractor runs fine, but has a hydraulic leak. Wondering if this thing is with anything or should be scrapped.

I recently bought an older Kubota B7100HST-E (2 wheel drive) with the serial number in the older set of numbers. When I put a 40 inch category 1 bush hog on it and started clearing my lot, I hit a...

Hey Guys, My B7100 fires up and gets to idle just as expected, but as soon as I put it under much of a load (even such as climbing a hill), it acts like it's too much. It starts to bog down and...

is the ground pos or neg on the b7100d kubota

Just picked up a B7100 with a little over 900 hours and in decent shape. I spent several hours doing routine maintainence but decided to remove the radiator which was full of debris and...

steering design not heavy enough will any other steering box bolt up

Hi, all! Just bought my first tractor for my hobby farm in Oregon, and haven't even taken delivery yet. My on-scene expert tells me that the Kubota B7100HST creeps forward very, very slowly when...

Guys/Gals I hope someone can help I have an old Kubota B7100 4 wd which is an absolute work horse for me on my small holding, the trouble is a noise has appeared in recent months. The noise...

Any useful info anyone has out there for me ?

Hello , friends of mine is going to change the engine in my b 7100 kubota and I would like to know if they need to line the transmission up when they put it together ?or any other info/tips would...

Hi everyone well been awhile since I have posted anything in here so here goes.Last fall I purchased a 94 Kubota B7100 hst it has a bucket loader and its handy for doing some jobs around the...

Hello, I have a chance to buy an "old type" (serial number less than N60163) Kubota B7100 HST. It is a 4wd tractor with good tires, and the seller doesn't know the year it was manufactured, but...

I have owned this 1984ish b7100hst for about 3yrs. I have never been concerned with the charging system, the PO said it does not work. I never used and lights, and it always started good. Now I...

well the smoke came out of the factory regulator, an the battery wont charge, ok call kubota...wow, i wonder if they are smokin crack? aint no way i'm paying that for a 4 wire regulator. got...

I am in the process of installing a temp gage on my newly aquired B7100HST. I bought it around Thanksgiving and machine runs. It had showed signs of being overheated in the past with the...

HELP! I've owned my Kubota for 5 years and suddenly lost the front wheel drive while plowing snow. First time after years of farm work with my baby. I removed the front differential cover's 3...

Just bought a B7100 with 2000 hrs. Runs great but would like recommendations on what oils to use for engine, case oil, gear oil. Standing by, thanks much.

Can anyone tell me what the auxilary hydraulic capacity is when connecting to the manifold block? What is the gpm on the pump and the pressure relief valve set at? I am wondering if it would...

How do you check to see that a stator/dynamo is working properly? The machine I just picked up had the wires unplugged from the harness and I think that it may have been unplugged for a reason...

Hello, New to being a Kubota owner. I picked up a used/tradein Kubota B7100HST. The serial number puts it at a '93 model year. The meter puts it at 1054 hrs. I am planning on cleaning up...

I've checked the fuses, emergency lights work, the tractor starts, but I can't figure out what to do about the hour meter, headlights and horn. Ideas?

I recently bought a well used B7100 (70's) and after removing it from the collapsed barn it was in and got it home, I spent hours reading on this site about how to fix the steering box. It was...

Hi guys: I aquired an old Kubota B7100, that has been sadly neglected. It has a tiller mounted, but the bearing where the shaft enters the housing on the right side has dissintegrated. Got the...

I have a Kubota B7100HST I will be selling and have no idea of what is a fair price to ask for it. I have owned it from brand new and it has just shy of 1200 hours. Maintenance has been done on...

A fellow I work with has a B7100 hydro-stat that the transmission has quit, all the other hydraulics work, I would think that would rulw out the pump, any suggestions as to what to check.

Hi.. this is my first post this forum. Many thanks to the members who host this site and the members who keep it going. I've been browsing it lots and the help and advice is wonderful.. so thank...

Just bought an older b7100. I mash the forward pedal and tractor drives in reverse. I mash the reverse pedal and the tractor goes forward. Please help

I have an old (1979) B7100HST that has run beautifully for 30 some years, but over the past two years, the transmission has been increasingly hesitant, at first being slow to respond when I...

i am looking to replace my rear hubs on my b7100, does anyone know where i can find some.

I have a kubota B7100 4wd hydrostatic that keeps running hot. Its not leaking water but have to keep adding water. Where's it going and why is it running hot?

hi i just bought a Kubota B7100 diesel tractor. its a gear shift no hydro. but i changed the oil and filter as soon as i got it. when you check the oil before you start it like you should the...

I have a B7100 HST with FEL and backhoe. I have been having intermittent trouble with one valve continually popping off the valve cap. After removing the valve train and reinstalling and...

Can anyone tell me what thread size the hydraulic port, with the handle, under the seat is? I'm assuming it's metric? It leaks when the revs are high, so I'd like to get a plug for it until I...

Hello friends! So some how while moving compost I managed to lose three of the 4 bolts holding my front left wheel on to my tactor. I've swept the entire path I traveled with a field magnet but I...

I am new to the tractor world and got my hands on a Kubota B7100D. The tractors in good shape and runs great. The question I have is about the trencher on the back. After looking at it, it...

Hi i need a diagram or need instructions haw i conect hydraulics line to the hydraulic pump. I remove the pump but i forget the positions of the lines. i got a Kubota b7100 4wd hs with loader...

Just got a B7100D in bad /neglected shape. It has a B1630 loader on it and a Kubota trencher on the back. It would be real handy around here if I can get it up into shape. The story I got was that...

Hi everyone, I have just purchased a b7100 Kubota with bucket and backhoe. Anyone got any ideas on making a log splitter attachment for the backhoe?

ok, so i got an older Kubota B7100 4x4 (i think gear drive) included when I bought a new house (YAAAY) has good tires, motor starts and runs - only smokes a little at startup. thats the good...

Hello, I am looking at buying the Kubota B7100HSD. I just bought 7 acres of land that's kind of hilly and was wondering if the hydrostatic transmission on these tractors hold up well running on...

First what a great forum!! I have read every thread (i think) on the steering box failures. Now after reading I have a few questions. 1. what exactly is sleaving? and can I do that or do I have to...

So i'm headed off to look at a used B7100 w/1700 hrs on it tomorrow. No FEL (unfortunately) but comes with snow plow, swisher 44 tow behind mower, and garden plow. i dont know the year but i...

Have an older Kubota B7100 that I am very nervous using without a roll bar. Does anyone know of one that may be available near CA Central Coast or have plans for one that we can fabricate?

I have a '94 B7100HST that is new to me. It had a problem where it would not return to neutral. The opposite pedal had to be tapped to get it stop travel in that direction. Annoying to say the...

Bought the B7100HST about 2 years ago. Use it to mow a bit over 1 acre yard with a 60" deck, and have a 50-52" tiller that gets quite a bit of use. Been half heartedly looking for a replacement...

i got a b7100 with a bad rear end, it pops and grides. is there any 1 out there that has work on them or know any thing about then. just trying to figure out how to fixs it

Recently purchased a used kubota b7100 and need hydraulic lines for back hoe any information appreciated

Well the last 3 mornings have been frosty,so I have the B7100 hst,the 4' snowblower.One thing I would like is a block heater or some kind of engine heater.My garage is unheated and it gets darn...

I Have decided to put chains on the front of my B7100. I've gone back in the archives and reviewed all I could find. For my tractor, size of tires and budget I think they will work fine. So when...

I have a buddy who has a Kubota B7100, 4wd, fel, runs great but the hydraulics are in slooow motion, what are some of the things we can check, thanks for any help.

I'm not mechanical. Its a real drawback in the world of tractors but this is the fact. So when my FEL started to stagger and shake and become unresponsive to the point that i couldn't get it into...

Hi, all My "fix" broke after only 6 months Sure could use some expert advice I replaced the rubber cover, brass ring assembly and cleaned up everything last time and thought that would be the...

I recently aquired a 1977 Kubota B7100. I have a drag blade and am waiting on delivery of an after market loader. Does anyone have a line on parts and empliments that fit or can be modified to fit...

I have a B7100 that leaks antifreeze under pressure only ( during mowing) . It looked like it was coming from the bottom of the radiator. I have taken the radiator off and drained the system. I am...

Hi I have an older B7100HST. I was wondering what each bolt was for on the attached pictures. Is bolt #1 on the axle used for checking the level and filling? What are #2 and #3 used for. Does bolt...

Well after a winter cleaning, re-ringing, and honing, it's time for the ol' d750a to go back together. Just a few questions. It'd be convenient if someone knew the answers, although I know they're...

I have a B7100HST and the input shaft that goes into the HST unit has the splines sheared off. There is a coupling that goes on this shaft and a pin that holds the coupling from sliding...

my B7100 reverse pedal works fine but it won't work going forward. The rocker pedal simply bottoms ( no tension in it at all, ) out w/ o any action on the part of the tractor. I've tried...

I have two B7100 HST (one old model one new) and behind the fan is what appears to be a water pump on the old one which is frozen and needs replacing. This is stopping the fan from turning and...

I'm reassembling my Kubota b7100 Engine after a re-ring and valve hone, and I'm just wondering if I can use new heavy duty diesel oil for all parts such as valves, valve springs, rocker assembly...

Hi, New to this forum and thanks to all who provide help here. I noticed that I am losing ever so slightly coolant from behind the thermostat housing between the gasket/flange and head. It's just...

My RC60 belly mower rusted out. Looking for a new or used one. Would consider a 54" if available.

Hi, I am seeing numerous B7100 (some HST) that say the HP is 20. But according to tractordata, it's 16. Is there a 20HP b7100 out there? Or are these sellers just misinformed?

Hi, I'm a brand new member and haven't learned all the forum functions. My question is that my dynamo on my Kubota B7100D wore out and has metal chips in it. I bought a replacement one, but now...

Hi guys Looking for some help regarding the function / operation of the drive shaft cover. Take a look at the picture item#10 is a metal pipe that covers the shaft held in place by a rubber boot...

Looked at a little B7100 4x4 today showing under 400 hours on the clock. No deck. There is a BEEFY subframe attached to a very large hydraulic plow with up/down and side/side cylinders. The plow...

Just bought this B7100 over the weekend and was moving some dirt around the yard with the loader while the backhoe was on the 3pt. I started noticing some intermitent noise coming from the...

I have found one of these w/ 1100 hours. It is 4x4 w/ a Kubota FEL, 4 ft Befco PTO tiller and a Kubota 3pt backhoe (not sure of the model). I drove to look at it tonight and had a chance to run...

i have b7100 loader for $1800

i have a b7100 loader for $1800

I have a choice to purchase either of the above, the 1700 comes with a BH while the bx does not I am planning to use it mostly for tilling fields, which one would be better at that, al

I was using my B7100 HST this afternoon and suddenly the forward and reverse pedal will not go to reverse. There is plenty of play in forward but none in reverse. I am new to this forum and...

I'd like to run front chains on my B7100 with turf tires. The reason I have not up to this point is that there is a very tight clearance between the tire and the steering knuckle. I'm concerned...

Thinking of buying a Kubota B7100HST-D. The owner thinks it is a mid-90's model. How do I figure out what year it is with no paperwork or titles to go by? Thanks, B.

hey all..looking for some help with my b7100 and found this great forum. Anyhow...my kubota drives very nice on level ground but when i go to drive up a hill....it just wont move at all...it just...

I'm looking for some experienced b7100 owners here to perhaps give me a little advice. This winter I'm doing a rebuild of my b7100's engine (blowing lots of oil at idle and lots of blowby at any...

Hi, I hope someone can help me with this question. I have a B7100 hst and I am planning to build a loader for it. I have some of the parts including the steel for the arms (already fab'd) and the...

I'm in the process of removing my crakshaft in my B7100HSD with the D750-A engine because someone before me had let the throwout bearing problem linger and thereby also wiping out the pilot...

What's the best loader to put on a 1997 3 cylinder diesel B7100 Kubota...is there one that comes with it's own hydraulic pump? Folks tell me to go with the Kubota loaders..which one is the...

After several hrs surfing, I'm no further ahead in picking the best loader for a Kubota B7100 HST (1997). ...Du-al, Woods, Koyker ?....Decided to ask you folks @ TractorByNet...what's the best...

So I was cleaning out the wood shed over the weekend and notice that the old Seat for the Kubota B7100 (I sold it almost 2 years ago and now have a B3200) was up in the rafters. What would you...

Where is my engine serial number? I have a B7100 HST. Others have suggested that it is stamped on to the block behind the fuel injection pump. My fuel injection pump appears to drop into the...

i am looking for parts diagrams and cannot find them online :confused: does anyone know where i can get these? Or even have them?!? ;) Pretty new to tractors in general and will probably need...

For those that hadn't followed my previous thread, here are some before pics. Here are the completed after pics. Brian

I did a Hydraulic oil change, and for the first time i tried to clean the screens. I was able to remove the pump side but I was unable to remove the HST side. I tried some penetrating oil and...

Our B7100 has had both rear wheels fall off about 4 times over the past 2-3 years. The factory part that holds the wheel on the axle is a brass(?) pin with a small spring clip on the end. I...

So, on my "new to me" B7100HST-E (circa 1982) there is a cool little compartment that says "Tool Kit" on it. Of course, it was empty when I got it. I've had a couple of motorcycles that had...

and whoops........ So I went and got big brother to help out

My b7100 started leaking oil Near front right tire (inside). It's a 4x4 and the newer style b7100. I don't have an owners manual yet ( I need one), could someone tell me the proper weight of the...

Hi, I am the new owner of a Kubota B7100 HST-E, two wheel drive hydrostatic, with a 60 inch MMM. Tractor is about a 1982, has 1180 showing on the clock but clock seems to not work. Was mowing...

Took the wheels and tires down Saturday and had new tires installed at Les Schwab $550 later. And today I made all new hydraulic hoses for the loader. This tractor had sat for about 4 years...

Hello all, I have B7100 4WD (4100 hours) with a pto problem. I was cutting grass with a belly mower and the mower and tractor stopped dead. The pto would only turn 1 revolution then stop. Took the...

Hi I was mowing last night and the mower stopped with a bang. I disconnected the mower and tried to turn the mid pto as it is a belly mount and it turns about 1 revolution then grinds. The rear...

We need a finish mower for our old faithful B7100 for mowing weeds at the back of our horse field. No idea where to start or what to look for. Any help or advice greaty appreciated thanks!

Anybody out there ever rebuild/re-new a hst for a b7100?? Mine loses power when the ambient temp goes up.. Been changing fluid & filters cleaning screens on a regular basis.. Thanks for any...

Hi. I'm a new owner of an old tractor. I've never owned a tractor before but a couple of weeks ago I bought a Kubota B7100D. This weekend I'm going to install the ROPS I just got from the local...

Hello everyone. My name is Rick. I bought a 1990 B7100 Kubota a couple of months ago . I am looking forward to getting good info on my tractor from fellow Kubota owners.

I recently bought an older B7100 with a Kubota backhoe. The backhoe is model #629. It has a full 15" bucket and it is too much bucket for that little hoe. Anybody out there have any suggestions...

I just changed my fan belt. Old one looked tired. Outside pulley has an odd sort of 'adjuster'. It seems positioned in place; however a bolt runs through it ---apparently to adjust tension...

Just like the title says. I need one and I just can't find one! Thanks..PoorDaddy

U-joints next to block was toast, it fell out! But putting them back is a good puzzle. I'm really not in a mood to install U-Joints up inside the belly of the tractor. I'd rather do it the easy...

I'm being given this tractor by a customer of mine. It has sat for a few years so it needs stuff replaced that you would expect. Tires, hoses, seat, battery, etc. It also needs bevel case seals...

My B7100 has overheated a couple times -- radiator clogged with dirt and grass. Anyway it now puts out white smoke in the exhaust and runs poorly. BUT if I take off or loosen the radiator cap...

Can someone provide an approximate price on a Kubota B7100 4 wheel drive tractor and accessories, to be sold as a unit? The tractor has 750 hours on it, it is a diesel. No ROPS, thought to...

I am looking for a B2030 blade for my B7100 HST. I have the subframe, mounts, and hydraulics. I bought this unseen as a set, but when I got it, the blade is some made-to- fit piece that belongs...

I have a pretty well used Kubota b7100, that I'm looking to do a couple small things to in order to give it back some good looks. The material lining the headlights and grille in one area is a...

Recently I've purchased a well used Kubota b7100hst made in 1983, and among other things that could use a little work, I have some questions about the hydrostatic transmission. Please forgive my...

I PURCHASED THIS TRACTOR USED. IT WAS IN 4X4 AND IT WORKS. TRIED TO GO TO 4X2 BUT LEVER WOULD NOT COME OUT. SPRAY WITH WD40 AND TRIED WIGGING BACK AND FORTH BUT LEVER DOES NOT MOVE AT ALL. TRIED...

I have a 1970s B7100 4WD with the OEM snow thrower. The oil feed hose between the oil distribution block and the control valve blew and I've had it made twice, both times they used the wrong...

I have a older b7100 4x4 that is gear drive and I was out moving snow yesterday for acouple hours. I was in high side using 4th and reverese in high side. I want to back up one time and it made...

i have a 1983 b7100. the loader and 3PT linkage seem to work ok but i have just bought a log splitter and it is strugling to split any wood. Is there a presure adjustment at all? Any help would...

If you are looking for some parts for B7100D 4x4. Check this Craig's List ad -- Kubota B7100 4x4 Parts Tractor The manual transmission went out on me and I decided it was time to upgrade...

Does anyone know off hand what the thread size is for the auxiliary hydraulic supply is under the seat on an older style B7100 HST-D? I am at work and cant check for myself. Thanks.

I had originally wanted to get the old steering shaft rebuilt, and had taken it to a reputable machine shop. The guy was not able to do it right away due to the holidays. Yesterday, I found a new...

Kubota B7100 1100 hours. Hi Guys have had this tractor for 20 years now. Bought it used at 300 hours, and it has been well maintained,and serviced all its life. Pushing snow the other day the...

Last year I had to snowblow by moonlight twice. Today I finally installed the work light I bought. To make room in my limited electrical power supply I replaced my headlight bulbs with LED 1156...

i built a front end loader from scratch and i am on the final steps of just getting the parts to power it I need to know who makes aftermarket pumps for it or the psi and gpm. and i also would...

Looking for the serial number location on my 1980's B7100D. Can someone tell me where to locate the serial number? Thanks

Anyone have an idea where I can purchase an inline engine heater for my B7100hst? I was hoping to mount one in the lower radiator hose. I found a link from searching the archives, but it seems...

The bad news is that I have an oil leak that I"m trying to pinpoint. I guess the real question is could it be anything other than the head gasket? Tractor runs fine and there is no water in the...

Hi, new user here. I just bought a 1980 Kubota B7100DT, with loader and shredder attachments, 1100 hours. The loader bucket stays in position when raised to any point, with tractor running, the 3...

Hey All, Just a heads up. - And a plea for help/direction if anybody can assist. Steering has been out on my machine for several months. After several gyrations, my local dealer called earlier...

I have a B7100HST, the E series. The neutral holder spring on this model is held by a threaded, adjustable shaft at the top end. The old top end bracket still exists from the prior model. When...

Picked up a B7100 today. Tractor is in excellent condition. One of the nicest used tractors I've ever seen, if not THE nicest. I'm extremely happy with the purchase. I have a Kubota Shop Manual...

Hi, Just bought it 2 months ago...1100 hours. Steering went out last weekend. Pulled the upper steering box and shaft. Upper roller bearing on steering shaft disintegrated. Bearings in the...

Hello, I have a B7100 Diesel Kubota i have taken this little tractor to a couple mechanics because it has trouble starting. They are able to start it for me and give it back working great. After...

HI, I recently purchased a Kubota B7100 HST. I think it is a 1996 model. This tractor came with a non-foldable ROPS. I have an orchard that I need to mow and there are lots of tree with a...

Hi all, Hopefully the ever-useful community can help out an owner in distress once more :) I have a few questions, so please bear with me! 1) Engine oil - I have the bizarre situation, whereby...

Hello, New land owner and just bought my first tractor. Did a lot of reading on this site and ended up purchasing a '94 Kubota B7100 HST with 500 hours. The tractor shows little use and appears...

I am restoring a '78 B7100D with a B219 FEL. The FEL was repainted at some point and I need to know the correct original paint scheme on the late 70's B219. I have seen photos that indicate that...

Hello - new to the site.... I have an issue where the tractor wants to keep moving only when there is a force working against it. For example when pushing mulch backwards with my blade. The...

I recently had to take a rear tire off my 1976 B7100.. The rear wheels were only held on by the pin that positions the tire on the axle in the correct location for spacing.. I need to know what...

I would like to find out which engines will interchange with my 7100. Will a 21 horse fit?

Still working on a restoration/reconditioning on my '78 B7100DT. It looks like it has been completely repainted at some point. The orange on it is a red/orange and where it is chipped off, the...

In all my Kubota manuals, I can't seem to find anything about the proper lubricant to put in the steering box. Is it 80wt gear oil like most other things or ??? The previous owner neglected the...

I am a new owner of a B7100DT that I am restoring. I have the original factory Operators Manual and Parts List, but no shop manual. I see two offered on the web. They are "WSM" and "I&T". Can...

I got a kubota b7100, I'd like to find some attachments, as in maybe a turning plow and a set of one row cultivators, does anyone know where I can find such things.

I'm contemplating upgrading from my B7100HST. My B7100HST is a late-model (I'm told by PO '98) with a Woods DuAl 145 quick-detach loader. I have brand-new turf tires and wheels on it, plus the...

Are these Kubota specific? My 3 Point Hitch relief valve kicks in at a little below 1500 PSI, but is rated for 1700 PSI. With its anemic 400 LB lift rating, the 3PH on this tractor needs every...

TBN was an invaluable resource in this project. The control valve is currently attached to my ROPS with plywood ( easy prototyping material for me ). I'm going to make sure that I like it where...

Hello Have bought a nearly new Kubota flail mower to use with my B7100HST tractor. It was fitted to B1700 when bought new but soon taken back to the dealer in exchange for a new larger tractor...

Hello Have bought a nearly new Kubota flail mower to use with my B7100HST tractor. It was fitted to B1700 when bought new but soon taken back to the dealer in exchange for a new larger tractor...

I'm adding remotes to my B7100HST. There is a large bolt next to the HST filter, is that the plug for the tank return hole? Type size/type fitting fits this, to connect a return hose? Tanks, Jay

Are B7100 and B6100 FEL's or BH's interchangeable? Or other models that might fit the B7100 - B7200? Are there differences between manual and HST mounted as well? I don't need one enough to...

Hi all, I did a search to see if I could find this out, but the only thread that came close kinda drifted away from fuel use into hour meter theory... Anyway, I'm wondering if any B7100 owners...

Ok so this is my first tractor. Not wanting to bother anyone, I bought a user manual. But it is of no help because I have a manual transmission and it is for a HST. On the right hand side there...

Greetings all, I have a B7100, the serial number indicates it's a 1979. I found a set of AG tires that I'd like to mount on the tractor, but they are from a later model B7100 that uses a six-lug...

So I have had this unit for 13 years and it was old when I got it. Over the years it has lost the ability to lift the bucket when it is fully loaded without increasing the RPM and waiting a long...

HI ALL, Just wondering if you can put the front blade from a B6100E onto a B7100HSD. The model number on the blade is KUFD110??? Any info would be greatly appreciated! Thanks, DDL

Greetings all, I just picked up an older model Kubota B7100 (1979 I beleive) and it's a really nice machine. Very well cared for and the paint still shines! My question is this; it does not have...

I need a steering shaft assy or complete steering assy. Any ideas where I can find it?

The transmission case is broken on my b7100 and was looking for a replacement when I found Kubota B6200 HST Tractor Transaxle Assembly - eBay (item 200284418046 end time Feb-02-09 19:23:36 PST) I...

Any comments on using the following on my B7100HST? Harbor Freight Tools - Quality Tools at the Lowest Prices It is rated for a max pressure of 2500PSI. The B7100HST relief valve is set for...

Hello Everyone. I recently purchased a tractor. I think it's a B6200D but on the left of the tranny it says B7100 on a aluminium sticker as you can see in the picture it is to worn to read a model...

Hi, I am new to tractorbynet. I have a b7100hsd/hst that has been sitting in storage unused since 2004. It has 480HRS on it. The tractor came with a property we bought back in 2004 but we never...

can anyone tell me how to Install Auxiliary Hydraulics on Kubota B7100

looking for shop manual and owners operation manual for my 1993 B7100HST, has any one scanned it into a file for their computer, thanks in advance

Hi guys, I've managed to track down a FEL for my B7100, but am having trouble identifying it as it doesn't appear to be the 'usual' old B219 or newer B1630? Any ideas from the following pics...

have not been on in a while there was a guy looking for a steering wheel for a b7100. can not seem to find the post if the person is still on please reply and or pm me after cleaning out my barn...

I am in need of some steering parts for a 1979 Kubota B7100. I have checked new prices and can't afford those to be completely honest. I was curious if anyone out there has, or knows where, to get...

Hello, we have a 1994 Kubota B7100HST-D with loader. Yesterday, it decided to stop moving while driving across our property with no load. The engine starts and runs fine, but pressing on the HST...

Hi everyone, first post here, read about every one posted about the b7100. Neighbor has a 1994 b7100 with 180 hrs on it with a few implements, tractor is like new, but has no loader. Kubota...

I've noticed quite a bit of blow by coming from the engine breather tube and after read up on it a bit, this seems to be a common indication of engine wear? It has been there since I bought the...

I have a model B7100 manual transmission. The steering wheel will rotate 1.5 turns. The slack adjuster has been adjusted. What needs to be done to repair this problem?

I recently bought what was represented to me as a B2150HST. However, on the transmission is a tag designating it as a B7100HST-D, 4 cycle, 3 cylinder. The engine is a 4 cylinder. Any comments...

Does anyone make a Top-N-Tilt kit for the B7100HST, or do I need to go custom? Anyone got one for sale?