kubota bx24

Stopped by the nearby dealer today and asked about the price for a 60" MMM for my BX24. Is $2500 a high price or right on? I thought they were $2000. Are there any other brands of MMMs that fit the BX24 or are their just aftermarket PTO mowers? I was told the MMM is by far the best way to cut...

Hi folks, new to the forum, but read threads often... I'm looking for a small TLB for landscaping work I do for my customers, but it has to be light enough not to tear up the lawns. Settling on a used BX24 with 100 hours vs. a used B2620 with LA364 loader and 50 hours. I would then buy a BH77...

Is there a way to "lock" my MMM in the up position so I can use the 3pt hitch without raising/lowering the deck at the same time?

Has anyone ever installed a trailer plug on there bx24. I'm thinking of adding one but not sure if I should go with a 4 pin flat or a 7 pin. I would use it when I'm pulling my 2 trailers, also if I go with 7 pin I couild use it to power some rear mounted atachments. If anyone installed one on...

I purchased my BX24 three years ago to perform many duties on our small horse farm. One of the duties I had hoped to never have to do was to dig a grave for one of our horses. Unfortunately, this past Thursday evening, one of my wife's horses had a severe case of colic and she had to put her...

I love my BX, in fact I pretty much love just about everything....Except when I mow I just am too far from the seat so I can lean back and be really comfortable. It is adjusted all the way up, and im 5'10 but 30" leg so maybe thats the issue or my arms are too short :) Not really sure, but is...

I love my BX, in fact I pretty much love just about everything....Except when I mow I just am too far from the seat so I can lean back and be really comfortable. It is adjusted all the way up, and im 5'10 but 30" leg so maybe thats the issue or my arms are too short :) Not really sure, but is...

My BX24 is coming up on 4 years old. Yesterday I went to clean some pine sap off the seat that dripped from a tree it was parked under, and noticed cracks in the seat material in several places. This tractor has always been stored indoors. Just turned over 200 hours. Wondering if this is...

I have a leaking hydraulic line on my backhoe, and am hoping someone can provide a schematic to tell me where the line goes once it's inside the BH arm? Thanks.

I am guessing there may be many ways to do this, but tonight I had to lift a 450# container and I basically used chains rates for well over this with tow hooks. I just clipped them on the backhoe bucket and gently lifted and it seemed to work ok. Is there a smart way to do this, or things...

I noticed without my BH on that there is a hole on the bottom which seems to fit a ball for a trailer just right. Is this OK to do? I haven't tried to put my BH back on but am concerned it will interfere?

On my BX24 the backhoe model#BT 601. The control valve is leaking and I think it is from one of the fittings. It is hard to tell which one since you need to operate the backhoe and look at the same time. So I tried tightening the fitting(s). The outside fitting was not leaking but was...

Hi everyone! Like some other threads, my BX24 just recently started doing this, rpms drop down to 800 or so, it struggles but I'm usually able to recover (thank goodness, I've got *steep* hills around here). 310 hrs on the machine. I just now changed the fuel filters, and 2 of the clamps broke...

Did a search but didn't come up with anything. This is my first issue with this tractor after owning it for 3 years. After restarting my tractor in my garage, after removing my FEL, I backed out and noticed a trail of fluid. My HST dip stick was gone. I found the dip stick in the horse paddock...

So I finally acquired a BX24 this season and I just picked up and installed myself the fine cut mower. Every dealers I called had a different story between the fine cut and regular. The bottom line seemed to be that they both cut well, the fine cut is sold to be provide a better cut, at least...

My BX24 (270 hours) has developed an intermittent engine power loss. The engine revs suddenly drop, say from 2800 during normal operation, down to below 1500 and it seems the engine is about to stall. If I let up on the hydrostatic pedal, and/or disengage the mower if it was running, the...

:(My 2007 BX24 began haveing transmission problems at about 450 hrs. After working for an hour or so, it will not reverse under any load, including up-hill, over small rocks, with a load in the FEL etc. I took it to the Kubota dealer, but he could not duplicate the problem. (cost $70 for...

Does anyone have a 60" MMM deck that they would like to trade for the narrower 53" deck? My 53" deck is about 4 years old, in good shape and located in southeastern NY. Bigger lawn calls for a bigger deck....

Anyone had the backhoe post break free of the floor? Mine has completely seperated - seems there are two small backets on either side of the post - and they have simply cracked off - pretty flimsy design it seems?

I have decided to get a SCUT TBL w/ MMM. My two options seem to be: 1) A brand new 2010/2011 23hP BX24 TBL, w/60" MMM and Box scraper for a 'best price' of $20,555 (out the door [tax, delivery, everything]) financed at 0% for 60 months through Kubota. (a $342.58 payment for 60 payments) 2)...

I was using my bx24 backhoe today to dig a trench when all of a sudden the hoe was making a squealing noise when moving the hoe from left to right and right to left. I shut the machine down and let it sit for a few and tried it again same noise. After about ten minutes the noise stopped but it...

I am finally getting around to hooking up my new 3 point hitch and the Landpride RTR0550 that came with the used tractor I bought. Pictures I have seen show the lower arms hooked up to the outside two clevis positions on the tiller, but when I did this....nothing wanted to line up. The manual...

I finally put together a modification so that I can get a good amount of firewood in my Kubota Tractor. The tractor only lifts 600 lbs, so super green stuff could be too heavy: Harbor Freight for the aluminum rack for $95. $50 for the Aluminum sleeve and aluminum sides. No Welding or drilling...

I am getting ready to use my 3 point hitch with a rototiller soon so I thought I would practice the BH removal. After watching all the video, reading the manual, I was ready. I went out tonight, hoisted it with the dipper and.....one pin comes right out, the other won't budge. I dropped it...

I was taking care of my neighbors horses last weekend and his BX24 is not running good. When you give it throttle (typically about 2500 rpm) it runs strong then almost dies goes to half throttle, back up and down and so fourth. I have heard that when the throttle control gets loose on the in the...

Has anyone ever rented out their BX24?? I had a request yesterday and I'm all for it. I am just not sure how much to charge. Anyone have any thoughts?? I believe it will be needed for about three days. I figured I would just charge by the day. The backhoe will be used to dig about five holes...

My 5 year old Kubota BX24 has an LCD display that is 90% all black when power is applied, I can't read anything. I had it tarped through the winter, but it fell off and I think snow melted on it. :ashamed: I can't seem to find the part online. If I replace it will it reset my hours? I...

I'm in the final stages of a decision to upgrade BX24 to L3800 loader/BH. I see the Hydraulic pump capacity is 6.3 gpm/3.8 gpm (PS). This looks lower when compared to others in the same hp range. (L3240 is 8.3/4.9) Any thoughts if this will impact performance in any way? or not to worry as it's...

I have a Woods GTC 52-2 Tiller, and need to change the oil. Does anyone know how to 1, check the oil, and 2 how much oil is takes? There is a plug on the gear box, a plastic plug with a gasket on the top of the transmission, and a drain plug on the bottom of the transmission, neither have a...

Hellow All! New to the site.

Can anyone help me understand the differences between the bx24 and the bx25? Is the bx25 merely a newer model?

Made set of Brush Forks today for a BX24, they work great. Dropped into the bucket with 2 pins, one on each side and ready to go. The forks extend out 42 inches from the front edge of the bucket and the rest remains in the bucket to the back for support. The forks will lift up in the bucket...

Anyone know if the bagger in the link below will fit a BX24 (60" deck)? KUBOTA MOWER DECK RC60-30B GRASS BAGGER SYSTEM BOOT KIT - eBay (item 140509563983 end time Mar-08-11 10:23:05 PST) Price seems as high as new....:(

Here's the story, when I originally bought my bx I had planned on buying a mower deck for it when my current riding mower died. Well now my mower died so I checked into pricing for the mower/bagger for the bx and it's in the ballpark of $4000. So now I am thinking maybe I should buy a zero...

I need to replace a thermostat on my bx24 do to a small leak. How do I drain the radiator?

Hey everybody I got a call from a friend that told me about this bx with 250hrs. I went and took a look at it and from the looks it needs a front seal and hst fan. The bucket is a complete mess the hood is cracked the seat is torn the front bumper is pushed back. The guy is asking $6,500. I did...

HI, I have a BX24. I was working in the woods and sheared off all the fins on the transmission cooling fan. A stick got caught up there while it was running and took care of it. Fan is cheap, said it is time consuming putting it on. Has anyone ever put one on, looks like need to break a...

I have the chance to buy a bx24 with loader ,bh ,and 3point balde for around 13000 with 168 hours any input

I was out yest moving some snow down the street when all of a suddon the machine started to loose power and died. Eventually i got a tow home and began the diagnosis. I had no dash lights no gagues and the fuel pump was dead; i had the emerg. flashers thats it. Wherever the short was it was a...

I'm thinking of selling my 2763A plow and replace it with a front mounted snowthrower. I have a few questions before I do this: 1) Which model snowthrower should I be looking for? 2) Should I hang onto the hitch, or let it go with the plow? 3) Is there another brand available beside the Kubota?

Today after a hard days use pushing snow around the yard I went to put the machine away, well being in low gear from pushing i went to switch into hi. Being on a hill i went to apply the brake to safely change gears when much to my dismay the pedal went to the floor ???????? Long story short i...

Folks Here is my situation, this year in the N.E we have had a good amount of snow fall. I have always had a dedicated snow blowing tractor (simplicity sovereign with cab) the tractor is only 8yo but the blower is 43plus years. That being said there is not much more that can be done to...

It stopped snowing, and the sun came out, so I decided to post a short onboard video of my BX24 with the 2763A plow in action. BX24 plowing video

I am going to change the anti freeze in my BX24 from what I have read almost any kind will do. I am putting in the green stuff. Question is: does anyone know if there is a block drain plug on the BX 24 engine or only the radiaton drain?

Does anyone out there know the bore and rod size on Bx24 backhoe cyls.? Thanks.

I wanted information on what the hydraulic pressure on a Kubota BX24. Having problems digging with the backhoe, thought pressures may be low. I cannot seem to find manufactures specs for it. Thanks, Reed :)

I'm looking at options to replace my BX24 with a machine next stage up. The backhoe is fine on the BX and given the option, could I use / transfer the BH on B2620 or even a B3200? I'd rather that then buy a new BH for a new machine (lots of coin). As stated, I'm just looking at options...

There are a couple of threads that talk about the brake shoes for a BX costing around $75, but I did not see any total costs for having the dealer do the whole job. Has anyone had this done? (and what did it end of costing?) From the way it looks, it seems like a fairly consuming project that...

Hi, I have read this forum since buying a secondhand BX24 about 2 years ago. First time posting though. There's lot of good information on here - very grateful to all those who post. I wonder if I can call on your help for a problem I have, before I decide whether to call in the mechanic and...

Hello everyone, I have a bx24 with about 200 hours on it. The other day it would not start and after a quick inspection it was apparant that there was no fuel. I looked on the forum and saw some discussion on changing the fuel filters. I replaced them today and it fired right up. The filter on...

My neighbors were kind of snickering when I bought the BX24 this fall. We live on a 1/2 acre residential lot and got the tractor for the long driveway and some landscaping next spring. This weekend we had a major snow fall....about 12" of really wet stuff. Snowblower and shovels were out, but...

In the 4 years I have owned (and enjoyed) my BX24, I have spent more than a dozen hours total (on several different occations) measuring, calculating and generally trying to figure out the best way to enable my BX24 with a quick connect connection for the loader bucket on the FEL. The two links...

Hello all I've had my new-to-me 2005 BX24 since Feb of this year. We recently moved to a different home on 4.2ac ...the reason I bought the BX. I`m a pretty handy kinda guy and this thing works awesome for my needs around here , it`s more than paid for itself in my opinion. Now to my question...

I just got this used tractor and I do not have a manual for it. I have ordered a manual. I have run the tractor several times, with no problem. Today I started it and drove it around to a spot to pick up some stuff. When I went to get off, the engine quit. I am guessing I did not have some...

I just got this used tractor and I do not have a manual for it. I have ordered a manual. I have run the tractor several times, with no problem. Today I started it and drove it around to a spot to pick up some stuff. When I went to get off, the engine quit. I am guessing I did not have some...

I am trying to replace the steering shaft and seals on my BX24. I have removed the steering assembly from the machine and can not figure out how to replace the seals. I know that several guys on here have done it, I just cant find detail directions. Can anyone help me here? Thanks

my BX24 acts like its running out of fuel when i go up a steep hill.it just started doing this 2 days ago .its not instant it take about 5 to 10 seconds facing up hill before it starts to die..

I was thinking about putting a Racor Fuel water seperating filter on my bx24. I was wondering If any of you have done this and if so which model/size you used. I have seen a few different sizes on ebay. I was also wondering what a sufficient micron rating would be for a bx-engine, I have seen...

I need to fix a slow leak on rear tire bx24. What tool do I use to remove lug nuts?

Looking to find a smaller tractor with FEL & back hoe for small contruction projects. The big stuff will be done by my sitework guys. I have found a 2006 BX24 with FEL, 60" mid mower deck and backhoe that has 97 hours. Privately owned and garaged with the 100 hour service just completed so they...

well the mice got in, and my dog decided to rip off the cover under the dash the metal screen, the bracket and ripped all the wires out from under the dash. I lost all dash display and was told that the wire harness is available ONLY as one complete strand (i.e, i can't just replace the dash...

To the you-plural of this group, If you have a snowblower for a BX24 (or 22, 23, 25), would you share the price he paid for it, and whether you bought it new or used, if you don't mind? Also, is it powered hydraulically or by some front PTO output? Thanks.

I found a 2006 bx24 with less than 100 hrs. Includes a 48" Bush Hog. What would be a excellent price for this machine? It appears to be in very good condition. I was hoping to pay less than $12k. Thanks

Made this for holding logs to cut firewood. Picture is before I painted it.

Hi all, I noticed today that my differential lock pedal on my BX24 felt as though it was attached to nothing but a spring. So, I popped off the wheel to take a look, and it appears that some linkage is missing. Would anyone happen to have a parts diagram or parts number of the missing...

Hi just want to post some pics how I did to solve the problem with no extra hydralic on my BX. Now I have two dubble acting circuts and one single acting. Please excuse bad spellling (I from the other side of the Atlantic). Now I can run my Dumper trailer:thumbsup:

Hi everyone. Its been some time since I was here, been working to much...with my BX24;) Ok this is the problem and solution (at least I think) I ordered some things for my 2007 BX24, 4month later it turned up a my yard, (please notice that I live in Sweden and ordered my stuff in US) So far so...

As usual took my inspiration from many great posts here on TBN >.. After 225 hrs decided to remove the backhoe to fab a rear carrier as we have 6 big (16" +) red & white oaks to drop & buck this fall - wacked by the gypsies 2 years ago. Carrier fab I will post in a couple of weeks, here is the...

Ok...took delivery of my used BX24 last night and since I won't really be able to use if for a few days, I have spent some time getting familiar with this unusual and beautiful creature while it sits in the garage and I sit on it with owners manual making tractor noises. Essentially, I don't...

I have been grabbing all the information I could from your site for the last several months as I made my decision on whether to buy a sub-compact tractor and which one. I just cut a deal on a repossessed BX24 with clamp on forks, land pride tiller and 391 hours. I bought it sight unseen, but...

I have a question, dumb as it might be but I want to buy an aerator for the rear of my BX24. Will the hitch provide down pressure on the aerator or will weight be needed. Now I know this may be simple to most but I have only had my BH off once and it was just to see how easy it was to remove...

I've noticed that over the past few days that the parking brake on my BX24 will sometimes disengage between the time I park it and the next time I return to the tractor. It seems that the pedal is extra sensitive lately, and if a grasshopper hops onto the pedal, it's enough to make the pedal...

I believe that my BX24 has 24 horses at the rear PTO. I am looking at a PTO generator and the one I really want requires 30. Do you think it will work OK?? What say everyone.

Hello guys , I recently bought a used `05 BX24 with the FEL and BH...I want to purchase a box blade for it. I`m thinking of going with the KK as it`s readily available from TSC for around $500 . My question is , and this is probably a stupid one :confused2: , but do I need the top links once I...

Does anyone know that thread size (not bolt head) on the Bx24 (D902) engine?

Yesterday afternoon I started digging out the poplar tree stump. Last month I cut down the tree since it was getting too big, and I hated the white cotton crap pluggin up the skimmer in my pool. I only spent maybe 3 hours just chipping away the dirt between the roots so I can cut them away later...

The tires that come on a BX24 suck. That's all I can conclude. After getting flats all the time, I put tubes in the front tires. One of the tubes went flat the other day (which I think was my fault from the tube installation, so I take the blame for that), so I said screw it and went and...

The manual for the BX24 states that the front axle holds 5 quarts of gear oil. This didn't seem possible, but I got 5 quarts anyway. At about the 3rd quart, it started overflowing. Is the manual wrong here, or is there something I'm not getting? I drained the old oil out of both drain plugs...

My BX24 has started to no longer run perfectly. The engine starts running as though it is starving for fuel, usually when it's under a load such as driving into a pile of dirt, but not always. It seems that it also happens when I'm on a slope, sideways. I'm not talking about the normal...

Hi all, I'm a first-timer here. I hope I didn't just miss this issue in the search tool. I have a 2-year old BX24 that I enjoy a lot. It has been trouble-free for all of its 77 hours. It doesn't get used a lot. Some irrigation trench digging, general pushing stuff around, but mostly just...

On hot days when running the engine at speed, the oil temp gets pretty hot on this little machine. It does not show any signs of problems, but I would like it to run a bit cooler. I was thinking of adding a coil and fan to the hydraulic circuit to directly dump some of the heat. On the rear...

I am building a subsoiler to go on my 3 point trailer hitch. I plan on running wire underground with it. The problem: I am in SLC building it, and my tractor got left behind at the cabin, so I have nothing to measure off of. If you have a BX24/25, and your 3 pt. arms are currently on it, could...

I received a post card from Kubota indicating my warranty was about to expire but that I could obtain extended warranty by contacting my dealer for a quote. I did and the dealer told me a 2 year extended warranty was $1300 or $725 for one year. Have TBN members been quoted pricing at this...

I have a BX24, bought with in the last year. Over the weekend while using the front end loader I noticed a hydraulic leak. I believe the hydraulic oil is coming from one of the metal lines that run from the connector in the front on the right side to the pump in the rear. The line runs...

Well I bought a Bro-Tek rear skid plate back in Dec. but never got around to installing it due to the fact that it was snow season. So yesterday I decide to break it out and install it. After removing the BH, which had never been removed (no fun the pins were so tight I had to pry them out), I...

Well with all the speculation about the Kubota BX7326 rear remotes fitting the BX24 or 25. I really wanted to try this. I purchased a kit and went to install it. I already knew I would be fabricating lines to reroute the backhoe return and also power beyond into the tractor. I was also going to...

The fuel gauge on my 2007 BX24 (110 hrs.) reads erratically. Most often it just pegs at empty, regardless of the fuel level. Once in a while it will comes back to life and reads correctly. The plug to the instrument cluster is tight. I checked the WorkShop Manual -- it lists Ohm specs for the...

I want to add T & T on the BX24. I am assuming I can use a two spool tandem center Joystick valve(like a Loader valve). Use a hose with a female ISO 7241-1 "B" series coupling for the "P" port and a hose with a male coupler on the "T" port and connect them where I would connect the BH hoses...

Does anyone know if they are "Industrial" interchange or "Safeway" interchange... or are they special?

Hey! I'm new to this forum, and to tractor ownership! I bought a used bx24 at an auction a week ago. I then bought a tiller and rear mower for it. Thing is, there's a backhoe where the tiller and mower go. I ordered a manual, but it hasn't arrived yet, and I have a tilling itch that needs...

What a great site. I own a BX24 with 260 hours. I noticed what seems like a slight grinding noise or some sort of clicking coming from the front axle area. It only happens when I fully turn either left or right. If I back-off slightly from fully turning the steering wheel in either direction...

Hello, I've been a member for a while now, just has never posted anything until now. I was wondering if someone would answer what's probality a dumb question. I bought a 2007 Kubota BX-24 with a LA-240( i think) Loader and a BT-601 Backhoe. Later I got a mid-mount mower deck. I'm over all happy...

Yesterday, I was BBing a horse pasture that had plenty of rocks in it. It was a pretty rough job, with lots of jolts as the teeth would hit a rock and pull it out of the ground. After I got done, while loading the tractor on the trailer, I noticed that the brake pedal felt odd. Normally, the...

today is a good day ,i tried to move a log with the backhoe.well the title says it all .it started smoking black and ran on when i took out the key.this ran for a 30-40 sec .when i flip it back up it didnt want to start ,like it was locked . i let it sit for about 15 min and it started.but now...

I have posted before about the blowing fuses on the BX24 and other random electrical issues... well - had a new one the other day. Started up the tractor - did a little moving around with the FEL - and when backing it in to park - it just dies. Instant stall. Humm - well - wonder what that...

BX24 will not turn off, had to stall it, can you help me with problem? Jim

I was adding some 55 watt work lights on the ROPS. I tied them in to the tail lights so they would come on with the headlights. Put two on facing rearward... No problem... Added a third one facing forward... and poof... they went out... about ten to fifteen seconds later... the engine died...

Hi all. Thanks for looking. My brother just bought a BX24 at an auction and it has no manual. Forgive my ignorance, but how in the heck do you turn the seat around to use the BH? Having a hard time figuring that one out. Or is it possible there is supposed to be another seat for the BH that...

Has anybody done the backhoe pivot move over a trench with a BX24? This a move in which the backhoe is used to raise the back wheels off the ground, and, using the FEL as a pivot point, move the raised back wheels over a trench. Once the lower BH pivot point is over the trench then the...

As many on here know, my neighbor lost his shop in a fire and got a BX24 to replace his burned tractor. On occasions, ive borrowed the tractor to dig out stumps and such but the common problem ive had and many other people have had was the tractor is really hard to start. Switches, lights, and...

I posted a while back that according to the specs there is not a big difference in capacities (loader etc) between the two. After using it for a full day the difference seems pretty big. Here are some early impressions My general impression is obvious - just that this is a much bigger tractor...

I was wondering if a GCK60-BX will fit Ok on a BX24. The catcher for the BX24 is recomended as gck60-23BX. Any help would be great.

Hi. Had a look at BX Panded website, nice one! Found a interesting thing, a hydralic pressure meter "get the most out of your BX". Has anyone change the factory setup (hyd pressure) ? Kubota has some kind of safety zone. I would really like to be able to lift more. It feels that Kubota arent up...

Hi. Now I will need to buy a snowblower to fit my BX24. Kubota has an org. 50inc front mounted one. Anyone has experience of this? 50inc. sound quite wide for 17hp on the PTO....? Thanks for your input on this subject! /Sam

I need to replace my BX24 tail light bulb. Messicks site list the part # K2581-62740. Does anyone know the generic bulb # ? (for example 194 ) Thanks- John

Made a deal with Barlows - great experience! I am getting a B2920 TLB unloaded turfs, loaded ags, thumb, front hydro blade and hitch, wheel spacers, rear light, QA, forks, 50" & 60" buckets with welded hooks, 16" BH bucket and a BX42 chipper. I really like the BX24 and was always amazed at...

I want to add a rear hydraulic hook up on my BX24. It will be used to make my rear blade hydraulic angle and other things eventually .I know that the backhoe has power beyond but do I have to have a control valve with power beyond? I was looking at Prince valve RD2575T4ESA1. Will the valve work...

I ordered chains for the rear wheels of my BX24. I probably should have asked the question here first, because the inner part of the front of the rear fender does not have sufficient clearance for normal chains, with just a little twisting the chains would tear up the plastic. There were...

I am really considering this. Both TLB with unloaded turfs. I love the looks of the B and the increased ground clearance. Here is what I use a tractor for on my 6 acres: 1. on grass for aeration, fert and lime. leaf removal after I get a vac. it seems like the 2 tractors weigh virtually the...

I am shocked at what this thing did with the rear chains on it. Almost 3 feet of snow and it was unstoppable. I angled the blade and kept it about 10 inches above the surface. I could plow in reverse for a pretty long stretch and then go back and lower then blade. This was MUCH more effective...

I own a BX24 with 220 hours on it. I bought it used with 200 hours on it. Note: This tractor has always beed stored in a garage. My garage is heated to around 70 degree's. None of the recalls had been done on it prior to me buying it. So I brought it to the dealer and had the back deck...

Hello everyone, I have a BX24 and am looking to purchase a BX2763A Blade. I may be able to get one with a B2733 Quick Hitch which was made for the B7500. My question is does anyone know if that quickhitch is compatible or do I absolutely need the B2751? Thanks for the responses. Pierre

I have the ability to purchase from a Kubota dealer a BX24 (LA243 loader & BT600 backhoe) that has the updated plastic and between a BX23 (LA210 loader and BT600 BH). Both tractors are under 100 hours and in very good condition. Price is about a $1000 difference. This will be my first tractor...

(cross post) I'm thinking about leaving the grass collector off this mowing season, and going with the mulching kit. Has anyone installed this kit on their existing 54" standard deck? How hard is it to change back to the rear collector? I was told there is some drilling involved to install it...

I'm thinking about leaving the grass collector off this mowing season, and going with the mulching kit. Has anyone installed this kit on their existing 54" standard deck? How hard is it to change back to the standard rear collecter? I was told there is some drilling involved to install it...

Thanks to reading all the posts here over the last couple of years I am realizing that I want a bigger tractor. I don't really know why except for tractors are kind of like TVs - why not have a bigger one? Anything new coming out on the B series? Would be a TLB no MMM- what other options...

I was wondering. Will the folding ROPS on a BX24 fit a BX2660 and if so has anyone made the change? What would the cost be? I would like to put one on mine if it can be done.

I have a quick question for those who have used the setup in the title. Once the blower is unhooked can the mid PTO kit and quickhitch stay on the tractor?? What about with the loader and BH on?? I dont have a mower anymore so thats not an issue. I'm due to pick it up this weekend from...

I am hoping I can buy these through the whole goods program. Is the only fit problem with the mower? it is an 08 if it matters. Thanks

I've been scouring craigslist and ebay looking for a used small to mid-sized tractor (20-30hp) with a hydro tranny to replace my B5200 so I can get out of the road faster when clearing snow. I also want a tractor that either already has, or can handle a small backhoe. I'm coming across A LOT...

Is anyone using a 60" rear snow blower on a BX24. I am looking at a 60" Meteor rear mount snow blower. The specs. call for 20hp at pto. The BX24 is only rated at 17.7hp. They make a 51" model, but I can't find one in stock anywhere. So I was just wondering if anybody has had success using...

Okay...this has probably been discussed before but I thought I would ask again to see if anyone has good ideas on how resolve this. I have to tap on the reverse pedal to disengage the forward drive all the time now. Brought it to the dealer to have them check/fix it...got slapped with a $60...

Does anyone have photos of the wiring plan under the instrument panel?? Bird dogs are great, until a mouse nests in your BX24 Radiator. He tore off the panel under the dash, ripped every wire and still did not get the mouse. a mess of 20gauge wires, i tried soldering what i could. seems like...

Just saw it today at my local dealer new for the bx24-25 nice and wide ,a little tall but fits nice. about time i've been waiting!!

if you're running a 2750 snowblower be sure to check the set screws on the quick hitch drive shaft. Cost me a $300. main drive shaft.My set screws fell out all of them.The quick hitch shaft sild foward and the main shaft slipped out .It broke the yoke in half at the rear ujoint and bent the...

I recently purchased a Wallenstein BX42 Chipper for my BX24. It dawned on me that the drive line protection on the PTO shaft that came with the chipper is really only protecting a device rated at 50HP with a shear pin. Would I be better off adding a slip clutch on the chipper versus just...

I'm thinking about putting a King Kutter landscape rake on my Christmas list, but I came across this comment about it (below). I don't really give it much credence, considering the person who wrote it doesn't come off as the most intelligent person around. But, it still made me pause to ask...

Never seen one myself. Are they worth having?? Have the opportunity to pick one up for 55.00. What do you guys think??

Does anyone have experience or info on mounting a snow plow on to the front end loader. I am not interested in buying a quick hitch system. Photos, cost and brands would be appreciated.

On my BX24, I need to adjust the contact on the switch that tells the machine that the PTO is engaged. It is set up to kill the engine if you have the PTO on and you get up from the seat. The problem I have had lately is that the engine will kill if I get up from the seat even with the PTO...

I've had my BX for almost two years(180 hrs) and have about 20 hours on the deck. I've had the bolts that hold the spindle in place pop out twice. I check them before every use now. The belt has slipped off a couple of times. I ran the deck with the plastic cover plates off and noticed alot...

I read recently some discussions on here about people using rear finish mowers rather than the belly mower. I was curious about what sizes people are using behind a bx. I have a rough cut rear mower now but am thinking of switching to a finish mower now that the property is under control. I...

I was digging and moving graval to untill i lost power and motor died all within a minute. Every thing checks out OK undee hood oil water and so on and now it trun over but will not start can any one tell soming about this??:confused: Thanks TTS 2007 BX24 230hr on it one service at Dealer....

Anyone have experience with these wheel spacers? Seem to be sturdy enough and significantly less expensive than some of the alternatives. Wheel Spacers Kubota BX24 Compact Tractor, Others :eBay Motors (item 120461828112 end time Sep-21-09 20:28:30 PDT) Note you can get spacers in three...

Any idea what the plastic hood costs for a 2007 BX24 and who has one. I got up close and personal with a log. The crappy hood didn't take the hit well. Next time I'll avoid sling loading anything as I know this is gonna cost me some bucks. Thanks

Good Morning, I have just imported a second hand BX24 from USA to Italy via UK (and am therefore a new member to this forum-This site is packed with some great stuff-thank you all). Unfortunately BX24 is not a usual model for Italy (I think it's primarily USA) and English Manuals don't exist. I...

I seem to have broken some linkage (I'm hoping that's all) for my differential lock pedal on my BX24. The pedal just freely travels up and down now without actually locking the differential. So, I'm assuming some part of the linkage broke off, or perhaps I just lost a cotter pin. Didn't...

TSC has a 10% off sale and this weekend is Tax-free in VT. Perfect time to buy an implement, or so I thought. I really need a box blade but none of the stores around me has a 4'. I could get the 5' for $499-16.5% off = $416. Not sure if a BX24 will pull it though.

I'm trying to learn more about my tractor and get somewhat of a baseline. I have a question for all you fine folks on here that has a BX23, BX24, or BX25. Do you notice any vibration on the driveshaft? My BX24 normally has very rough idling at low rpm's but generally smoothes itself out at...

I'm thinking about taking on the task in order to save some money (closest shop is 50 minutes and they quoted $550 for the $10 fan). I'm not an expert but am somewhat handy with tools and very willing to learn. I have attempted slitting the fan in half and epoxying it to the old fan hub but...

Not isn't this grand? What he teaches his techs to do is slice the fan and epoxy the seam back after bolting so to save the customer some money. The problem is that the bolts cannot be accessed (easily). The regional service rep is at a lost when it comes to replacement of the HST fan on a...

OK, this is a continuation of my post of me tearing up the fan by driving over a twig after about a year of use (I guess you can say that I got a little comfortable with it and forgot to pursue the skid plate addition). I did ask the dealer about any kid of protection for that fan back when I...

I live on the side of a hill and had a 70 year old silver fir cut down as it was dying. The next day we cut it up and loaded it on the tractor and hauled it to the top of the hill. The little BX24 can climb some pretty steep hills. I accidentally unloaded the bucket with the log in the back hoe...

To me this was simply a bad design. I backed up into a little stick it and took out all the plastic blades. Anyone ever had that happened? How easy is it to replace the fan (directions please) and how much for the part and also labor if I were to have it done. I'm fairly new to tractors but...

My BX24 MMM lift is not working the way it should. I can raise and lower the MMM with no problem. I just can't get it to lift all the way to top so i can turn the knob to TOP . I also noticed that when driving with the MMM lifted as high as it will go, it bounces against the stops and it drives...

In the attached photo, I'm pointing to a bracket that is on the back of my BX24. There's one on each side. What are these for? They look like good tie-down points for transporting, but is that what they're there for? Thanks

Folks I have had my bx24 for about a month now, I have finally sold the other tractors I had and now find myself in the position of needing to purchase a MMM either a 54 or a 60". I have searched the forums and am trying to find a list of compatable model numbers that would fit my machine...

I have a bx 24 and have a question; sitting on the tractor on the left is the controls for mid,rear pto's.However the lever to engage the pto touch eachother,therefore you can't pass the levers past eachother.I don't have a mid mounted mower ,it's a TLB set up.

Does anyone know the critical grade where a BX24 is likely to tip over? I've been thinking about some sort of pendulem mounted on the front end loader that would indicate when approaching that danger zone.

Hi. I just did my 300hours service. My BX24 lives a hard life but well maintanied live. Please check your BX,s so you dont have this potential breakage as I find out. I have to order a new waterhose on monday. /Sam

I did not notice the gauge. Saw a little smoke and the temp needle was in the red. I shut the motor off...what else should I do? The reservoir cap was open and it looks like most of the coolant is gone. Should I put some in and run the motor or should I let it cool down first?

Here are some pics of my back yard. After I move all the wood and branches out I have about 30 2ft+ stumps to remove then topsoil and seed in the fall. I am also going to rent a chipper to get rid of all the crap 4" and under on my property. I removed about 50 trees then paid someone to do the...

Just got a used 10,000lbs GVWR tailer for hauling wood/hay/tractors. Trailer load can go up to around 7500lbs and I've got it attached to a GMC 2500HD with tow package that can tow 10,000lbs, so all weight restriction bases are covered. Drawbar and hitch are rated for 12,000lbs. So, I tried...

I was reversing the seat on my BX24 today and at some point I noticed the lever that is lifted to release the seat had come off and there were three parts on the tractor deck: a spring with a couple of tangs on either side, a washer, and what looks to be a curly cue pin that probably goes...

I have a 16' tandem axle trailer with ramps; and bought both DOT chains and binders. I would like to secure my BX24 without damaging the paint. I thought I could put a clevis through the drawbar pin hole and chain the rear there but haven't found a good place to chain the front of the...

I came across an almost new BX24 TLB which also comes with a 50 inch snowblower and 54 inch mid mower, only 41 hours on it and it looks nice. He's asking $16500 for it. Sounds like a deal to me...

I've owned my BX24 for over a year now and have experienced no problems... until recently. First is the hour meter. I typically don't look at the hour meter every time I start it, but last week, I wanted to check the # of hours for possible servicing and noticed the hour meter read 67287.5...

My son and I need to get firewood where a trailer can't go, so I am curious as to how much wood you can put in the bucket. A pallet on the front takes up too much room. Tight in the trees and steep. (I don't sidehill at all) Here are some pics of my first successfull trip climbing out of the...

My front tires on my BX24 are always losing air pressure after sitting several days & I would like to put tubes in them problem is I cannot find tubes to fit a 18 x 8.50 - 10 tire, anyone know where I could find them in this size or a size tube that would work ok Thanks, Glenn

Having moved to a new development with many young families wanting to put sweat equity into their new homes, I figured I could make a buck or two with my Kubota BX24. Yes sir... I was right. Why sling clay for hours and hours when you can hire someone ($50/hr) for an hour or less to get it...

I have a mowing deck on my bx24. When I start the PTO for the mower it takes forever to come on. Is there something that I am overlooking when I start the mowing deck???

I was planning on using my boxblade yesterday and removed the BH. When I grabbed the 3 pt hitch assembly, I started installing it and noticed one of the threaded adjusters was bent. I could probably bend it back in a vise, but suspect the structural integrity is compromised. It's the 8-10"...

I'm looking to get a 48 inch brushcutter and was wondering what brand people are using and if they had to do any mods to the 3pt ot get it all working properly. Trying to avoid that. Thanks

Has anyone ever replaced the transmission cooling fan on the propeller shaft of a Kubota BX24?. I got the parts blow up, but it does not tell me the steps to remove it....thanks for any help.

The first one was fun, but after about 75 I thought I'd share the pleasure... Here's a video of my BX24 digging out a posthole using a 12inch auger. The soil is mostly heavy clay/loam. I hit just a couple of rocks so far. The little beast does pretty good. YouTube - bx24 posthole Also included...

I have been thinking about purchasing a 60"MMM for my bx24 now before i wait longer and prices go up. I have a scotts S2554 garden tractor, which was made by deere, that i use now for cutting the lawn. Its in great condition and runs great, but eventually when i get most of the main work around...

Today I found what appears to be a broken o-ring on a path that I drive my tractor down on the way to my dock. Nothing else mechanical goes down it. If unbroken the o-ring would be approx 4.25" in diameter and the rubber is .095" thick. Does anyone know if this sounds like a part off a BX24? I...

If so, what implement is the correct tool for this task? I have a mowing account client that has a couple acres of field he would like mowed 1 or 2 times a season...It is fairly level and wide open...only a couple of brush "islands" here and there. Was wondering if the income from the mowing...

Found in CL DC What not to put in your FEL /edit - sorry should have put it in safety

I really like my BX24 but I never use the back hoe. I bought the tractor for two main purposes. Along with other random duties. Maintaining a dirt road to and around my property with a box blade. It's done quite well at this but it wouldn't hurt to be bigger and faster. Second pulling my boat...

I am considering a bx24 and the b26 kubota`s I would like to use this to brush hog and box scrape my driveway. I will be digging some pine stumps and general clean up around my cabin. My question is which machine would be the better choice ? And why is there such a large price differance in...

Was 20 miles from home and 3 miles from the nearest Kubota dealer when I noticed a trail of fluid on the ground where I was taking a few inches off an old deck base (1 inch stone). I had no tools with me and couldn't see where the fluid was coming from because of my Brotek skid plate (front and...

Hi. I need to fit a "kit" for my bx24 to get two extra hydralic couplers at the rear. I cant find the kubota part number for this kit. If I remember you can buy this as an option. Over here in Sweden the BX24 doesnt exist, but the BX2350 exits here. So if I order a this kit for an BX2350 is...

I just came home with some diesel as the bx24 was thirsty. I hopped on after it's feeding and it was fine. Unfortunately after a 6 point turn I pressed the forward pedal and it barely went down and I was going sooooo slow even though throttle set near maximum. I used the reverse pedal and it...

After feeling uncomfy driving my BX24 on some of the slopes on my property, I read about and bought a 25C tilt meter. I figure I'm not the first, so I was wondering how other BX2x owners have mounted their tilt meters so they can both be vertical and easily seen from the seat. I also am...

Has anyone had experience with hydraulic post driver attachments? I'm looking at purchasing a post driver for my BX24 - a Shaver PD8. Weight is fine since my machine has the backhoe. According to the manual and the latest check by the dealer, the hydraulics are at minimum for operating the...

i've read the threads i could find on TBN. seems like the consensus is generally: - good performance of the bagger - need to empty (too) frequently - pita to attach and take off just priced it at the dealer for $1820. he told me there are two different attachment types and i need the type...

I just received a postcard in mail about my warranty is about to expire soon. It also has a statement about calling to get a extended warranty. I havent needed to use my warranty at all, but Wanted to touch base with you guys and see what you think? How much would it be ? I am afriad to call to...

Does anyone notice any difference in speed from 3/4 throttle to wide open throttle?

Houston based listing for only a few thousand bucks.

Does anyone know if the BX24 & 25 'skin' parts are interchangeable? Like the hood, rear fender, deck, etc. I was going to contact Kubota direct but did not want to call China. I have the BX24 and was looking to possibly replace the hood and deck from a BX25 since they are steel and the BX24 is...

It has taken me a week to get up enough nerve to tell you guys this... I was working on breaking down my last pile of trees (see pictures) that the excavators made when I had some land cleared. I am using a chain to pull apart the pile and burning a small pile about every week. One pull with...

I have had my BX24 for about 1 1/2 years now and one of the reoccurring problems that I have noticed with the machine is when you put the outriggers down to use the back hoe they sink into the ground very easily. Then when you start digging, and tugging on a stump or large rock they again don't...

After almost a year of my tractor sitting under a make shift roof and sorta getting wet, I finally purchased a new 12'X24' garage. Now I need a proper ramp (couldn't wait to put it inside, so I used car ramps) and shelving to put inside. The first picture was it's former home. Now I can finally...

A while back I asked about tool boxes for a BX24. I finally made one today after reviewing what others have done. The following is a link to my original post. http://www.tractorbynet.com/forums/kubota-owning-operating/132288-bx24-toolbox.html Also, I attached some pictures. Thanks to all who...

I have a long dirt road I maintain with the BX24 and 4' box blade. It's been working fantastic. Sometimes I put it in high gear to speed the job up. It doesn't seem to phase the tractor and I only do it if the box blade is lightly filled or I'm polishing it off. But when I do this I do smell a...

I was wondering how well the backhoe works on the BX24. For instance, how long might it take to dig a 100 foot trench 3 feet deep in soil that is mostly clay with mixed in shale and stone, etc. (no boulders) One day? One weekend? One week? I'd be using it primarily for digging trenches to...

Hi, A little help please. What are the differences between the BX23 and the BX24. Thanks, RTJ49

Anyone rent a uhaul trailer to tote their BX24? I don't have the need to buy a trailer, but would like to take my tractor to my cabin to do some yard work, once in a while. About 150 mi trip. Any suggestions? Car carrier perhaps? I live in MA.

I mainly lurk here as I have little to add to the expertise. But I had to say thanks to all for two things. First was when I ran across the thread about low fluid levels in the front axles of BX24's. I went out and sure enough mine was low. Not a lot of hours so I don't think any damage was...

I think If I had it to do over again I think I would have bought a BX23 or slightly bigger with no back hoe. It's nice having the back hoe but I rarely ever use it but I constantly need the 3 pt hitch. Is it ok to just leave the back hoe off for months at time. Will it collapse? Since the...

I have a 08 BX24. The hyraulic pump seems to be a little noisy. It is especially noticeable when then a piston is fully extended or retracted -relief valve is operating. I changed the hyro fluid last fall and have not really used the machine very much during the winter. The fluid level is good...

I recently bought a canopy for my RTV900 and I am surprised at how much I enjoy it. Now I see the value and plan to add a canopy/sunshade for my BX24. In searching through past threads, here are the ones I found: Kubota Tractor Canopies | Kubota Tractor Canopy Sunshades | Sun Guard LLC Wells...

I'm in the process of purchasing a used BX24 and will be picking it up Tuesday. I also found a snowblower being sold that fits a BX23 but am not sure it will fit a BX24. We (snowblower owner and me) checked with two Kubota dealers and got different answers. One said yes, the other said it would...

Does anyone know why the BX24 is not available with R1 tires? I thought I've read that it was a compatibility issue with the MMM. What if I never put on a MMM? Would love to get Ags on if possible.

I am in the buying process and plan on picking up a 2008 BX24 on Friday. I was told buy my local dealer that the BX24 and BX25 are basically the same machine and the BX25 is just the new model. I asked if the BX25 was replacingthe BX24 and he said no. I called Barlow's and Steve said they are...

Ok, we've recently borrowed a BX23 to dig some asparagus trenches, and it was great. We used it for other small odd jobs as well. We think we may get one. Here's what I came up with: John Deere 2305---$16,718 Kubota BX24-------$16,673 Kubota BX25-------$18,445 All TLB with R4s and 12"...

I did a search and got some threads with some opinions, but no definitive answers. Can someone provide the actual size(s) of all zerks installed on a BX24? I have one on my FEL I need to replace, and would like to get a set to have on hand in case any others become faulty.

Has anyone had any experience with an LMC clipper 400? It looks like a good match for my tractor without FEL as ballast.

i was wondering if the bx 24 has down pressure on its 3 point hitch