Search results

Not able to post pictures and getting message that file is too large for server. After resizing is still getting the same message. I see others posting pictures so what is up??

The thumb will clamp down but will not retract. Wondering if someone could help with best way to trouble shoot?

Considering updating our wood stove to a Vermont Casting or Woodstock soapstone stove using catalytic combustion. Using an older non catalytic Jotul stove at the moment and it works fine but uses a lot wood and is not quite big enough on cold days. So we would consider upgrading to a larger and...

The safety valve on the oxygen regulator started to blow. Wondering if it is a faulty regulator or faulty safety valve? Anyone with experience on this?

There has been several discussions here about boots and what are the best boots to buy. Most of the boots recommended do not necessarily fit your foot in the best way but is a way of selling boots with a fit that hopefully can sell them. One aspect that is not talked about much is the arch under...

I have many old 35 mm color slides that I would like to save in a digital format. There are several hundred of them and I may want to save perhaps a hundred of those. What is the best way to do this and what is your experience with buying a copier or using a service to convert them?

The brakes on the 10,000 lbs equipment trailer are not working. I do not use it often and the F350 dually has enough brake power when lightly loaded but would want to make it legal without a lot of expense. First problem was the connections on the wiring were twist on types or crimp types and no...

I was going to use the winter down time to retrofit an air suspension seat to the 331. The stock suspension seat is not very good and it slows me down during mowing. I am working on getting a Grammer seat base functional and using it on the mower. Turns out a wire was pinched inside the seat and...

The heater in the cab is blowing cold air. Checking further into it seems that the actuator that turns the coolant valve to open is not operating. Messicks parts site show it as a 400 dollar item but believe it is for the assembly including the water valve. Will call them on Monday to check on...

Just trying out filing picture of the minix

The old M7040 comes in handy. It is surprising in the power and utility around here

Trying to post

The old MF 203 industrial tractor was sitting for a few years. Wanted to bring it back to life and it would not start. Changed the fuel filters and the fuel lift pump and bled the system and checked for fuel flow at the inlet to the injection pump. Next loosened the inlet to the fuel injectors...

I have an issue with neighbor mowing on my side of the property line for a distance of about 2000 ft. I guess he wants it to look more manicured like his estate is. This is a rural farm with a tree planting along the property line on my side. Told him to stop and I put up tee stakes and fence...

Out driving today saw someone building with two 40 ft shipping containers and a roof on top between the containers. Looks like the spacing between the containers was 30 or so ft and the roof was prefabricated tubing. Not sure what the plan is for the roof covering. Would love to hear from others...

The transmission slips badly when the oil gets warmed up. There must be some internal leak inside the transmission when the oil gets warm. At cold temperatures the transmissions performs normally. I may have over stressed it pulling a trailer because it was after that it became evident. Before...

Have been looking to get a mini x such as the Kubota KX033-4. Would like a new one if possible to use on the small farm here in Maryland. The list with a few buckets is about 60 K. Not sure what a realistic selling price would be. Kubota has 60 months with Zero interest or discounts for cash...

I have an old Massey Ferguson tractor where the hydraulic system for the loader as well as the power steering calls for type A transmission fluid according to the original manuals. Can it be substituted with Dexdron III fluid?

Got this trailer mounted welder with an air cooled diesel engine about 10 years ago and have not started it since. So decided to see if it would start. Installed a fresh battery and pushed the start button. Wouldn't you know it barely turn over the engine before it started. Runs like a top with...

Hi, wanted to know if you have some suggestions about how to go about selling my Woods 15 batwing finish mower. It has been used two seasons on about 10 acres and has somewhere around 300 hrs on it. Live in Maryland close to the town of frederick. Any suggestions are welcome Thanks

Used one season approximately 300 hours in new condition. Located in Frederick Maryland. Make me an offer.

I want to sharpen the cutter blades on my 72 inch Landpride bush hog but the blades mount on a large stud attached to a disk about 24 inch diameter. There is no visible way to unscrew the blades that I can see. Do I unbolt the center hub and take the whole assemly off or is there another way?

here is how I mounted the wheel weights without having a forklift like the dealers. Very simple to do and saves a lot on the back. All about leverage

I am trying to mount the three wheel weights on each wheel but find that they are too heavy to lift by myself. Wondering if someone has devised a way to handle this via some simple rigging device?

Rocks are like icebergs you dont know how big it is until you dig it out. This one was huge and the FEL could not lift it so had to push it out of the hole on a ramp and then over to where it is now. Not that I used a 4-one bucket for excavation and pushing the rock

this is what a hard working M7040 looks like after a long day of dirt moving

anyone have experience with the Plew 18 volt rechargeable grease gun as sold by Northern? A little more expensive than Lincoln but looks very nice and comes with two batteries.

Talked to the dealer about where to hook up the hydraulic winch and he showed me where there is a short hose that continues from the FEL valve back to the three point valve on the right lower side of the tractor. He recommended to take this hose off and install the new spool valve in that loop...

Attached is a pic of the 12 volt electrical outlet behind the seat in the cab of my M7040. The outlet is for accessories and one terminal is hot all the time, one is ground, and one is hot when the key is turned. May be this is a common outlet in Japan but no one here knows where to get the...

I am going to install the Mile Marker Hydraulic winch on the 7040. It will come with a spool valve that will protect for full pressure from the pump as recommended by Winchplus. Will install it on the front instead of the brush guard and high enough to be able to use the FEL bucket as a wedge to...

Here are a couple of pictures of the Golight search light that I mounted on the tractor cab corner instead of the regular worklight. It works off the remote control shown in the second pictures and can swivel in all directions at two speeds. It is quite a focussed beam at 500,000 lumens...

what do you think is this the biggest tractor tool box??

I have a a Deere 8B BH that has some of the grease nipples torn out of the housings and the treads are stripped to the point that inserting a new nipple will not work. Any experience anyone in a simple fix? Welding a nut on the outside will that work as a fix?

Installed the poly cutting edge for the snow plow. It is 8 ft by 8 inches wide and 1.5 iches thick and blots on top of the existing cutting edge. Forecast is for snow tomorrow so will be ready to test it out. Should be preserve the pavement and minimize plow damage to the grounds

This is the biggest Rock I have managed to dig out with the FEL. Had to move a lot of dirt on three sides to push it out. Then push it a little and backfill behind it to get a better angle of attack. Damaged the brush guard in the process when the tractor slipped down in the hole and hit the...

There has hardly been any snow this year to be able to test the 8 ft snowplow on the tractor. Tried it once and it is scraping the pavement pretty hard. Figured out to place the FEL in the float position to let it follow the road but still scrapes hard. Next used the curl to tilt it to ride on...

http://www.tractorbynet.com/forums/jd-owning-operating/93545-4-one-bucket-other-pics.html

Here are a few pics. The first two are of the Bradco 4-in-one bucket that I picked up yesterday. Pics 3 and 4 are of the top hydraulic link and also showing the bend tines on the box blade. The tractor has too much HP for this bucket but it sure ripped up a lot rocks in the process and was able...

Noticed that the M7040 new owners got cast iron rear wheels with their tractors where mine was delivered with plate wheels. Asked the dealer today and he responded "that is an option that I did not purchase but he could look into this and tell me how much money it would cost to backfit"...

received it yesterday and just welded it on and installed hoses

There have been many posts on this over time. Wanted to get a rock/root grapple from WR Long but now I am thinking that a 4-in-one bucket will be more useful overall. Most of my work will be moving dirt and rocks, leveling, lifting things. The 4-in-one bucket can clamp and lift as well so may be...

wondering if I have enough clearance for chains since looks like with the ag tires very little clearance is left between the tires and fenders? Has someone looked into this?

Just installed one of Mark Carter's toplinks this weekend. Works like a charm. Now this cylinder has check valves built in to prevent drift in position. Question: Is it possible to backfit check valves to the loader cylinders and has someone out there done this??

not surprisingly the TSC carry all broke when loaded up with a pallet of firewood. It was 6 ft by 3 ft and 6 ft high. Too much weight. So now I am looking for a three point quick attach bracket so I can use my FEL pallet forks in the rear. Anyone know where i can get a Cat 2 quick attach bracket??

Anyone know where I can get a 3pt cat two quick attach bracket so I can mount my pallet forks on the rear of the tractor??

Have been looking for a ballast box for a while and the available boxes were too small and costly for my taste. So this weekend I used some two by lumber laying around and a chainsaw and a framing nailer to fabricate a large box filled with crushed rocks. Purchased a carry all from TSC and now...

Anyone know where I can get new rims for the rear wheels other that the dealer. Are there generic rims available or how does that work?

I was thinking about mounting a hydaulic winch on my tractor hooked in to the the FEL outlets in the front. Looking at the website it states that they operate at 1500 psi and 3.5 gpm. My system is 2500 and 11 gpm. Does anyone know if it will work reliable in this system?

Looking at the M series it is noted that the engine displacement is the same 203 Cubic inches for M7040, M8540 and M9540. The higher output of 85 hp and 95 hp is achieved via the added turbo charger on those models. The M7040 is a normally aspirated engine. So in theory we should be able to...

Have an MF 203 industrial loader tractor that I have rebuilt and improved on over the years. Wondering about the history of this tractor? There are many accounts of the history for older models but they all seem to stop at the 200 series. The 203 was made in a farm model and the industrial...

this is the JD backhoe mounted on a 50 HP MF203 tractor. Works really well and operates usually at only 1200 rpm which is plenty fast since it has 17 gpm hydraulics.

this is the underground fuel tank that I dug up today. Note that the holes that the teeth on the bucket made in the side. Stinks very heavily of gas. Will leave it to dry out before doing anything more with it.

Here is a pic of the air seat with the swivel plate. Very comfortable with for and aft dampening as well. Also note the spot light that is attached to the arm on the left door

this is pic of the snow plow for the M7040. Is it big enough?

hope this works trying to attach files and learned about resizing the pic first

repaired the swing cylinders this weekend and replaced the seals. Took several hours to get them out cleaned and replace the seal. Most difficult part was to get the links off the chain that the cylinders were connected to. Also stripped several treads on the tie rods and had to weld on the nut...

yesterday wile digging ot an old gas tank on the farm I busted a hydraulic hose for the FEL curl function. Lots of oil spray before I could shut it off. Is that one of the hazards that needs to be cautioned against? Think that slamming into the dirt with the bucket tilted caused too much...

I have still not figured out how to attach photos to the Threads. I have the photos on my computer and wanted to copy and paste but apparently that is not the way to do it. Can someone help explain this for me?

Still bugs me that there is an auxilliary 12 volt outlet in the M7040 behind the seat and no one knows where to go and get a matching plug so I can actually use it. It has a black screwed cover on it about 1 1/2 inch dia and it has three prongs. Middle prong side to side and the other two up and...

-------------------------------------------------------------------------------- My tractor has the new hydraulic PTO engagement system that will not allow turning the PTO shaft on the tractor to line up the splines. So the only way is to turn the PTO shaft of the attachment implement to get it...

Want to add a ballast to the M7040 for when doing loader work with full bucket (72 inch). Seems like the stability without is Ok at least it did not feel unstable when I did a couple of hours of digging with it. However I think the traction with 2000 pounds of ballast would be much improved...

Have an old MF203 industrial model with FEL. Are there other MF203 owners out there? Seems to be a model that there are very few of?

Wonder where to get a grapple for my loader on M7040. Seen a few thum types but they look light duty the 72 inch FEL bucket Any recommendations??