Hi All! Noticed I had a headlight out. I rebuilt my grill over a decade ago, and I remembered the bezel was held on by an odd spring clip. I managed to pop the bezel off, but can’t figure out...

Hi All! First off, forgive my long-winded ramble. Just trying to give as much info as I can. I went out to do my pre-snowstorm check on the Ford 1700, and discovered the battery was dead. It...

I need help sourcing cylinder seals to rebuild all 3 boom cylinders, Can't find replacement seals online. Any suggestions are appreciated.

Hello. Have a Ford 1700. Not in any way, shape or form a mechanic but thanks to this forum have kept it going 15 years now. Have a new issue which has me stumped. Unable to start tractor. It...

Hi! I have an old Ford 1700. Recently, the control arm for the 3pt lift has been "slipping" up. Messing around with it, it goes down with resistance, but when I pull on it, it moves pretty...

Hello, Hello, i have you ever ran across s 1979 ford 1700 will not move and stalls when clutch is released, I was connecting to an when I tried to take off, the tractor would not move. When I let...

Hey guys, first post. I've been googling and searching this for months and I'm still at a loss, so finally decided to just pose the question outright and see what folks more...

And how did the snow get in there, you ask??? Well, because I'm a STOOPID - that's how. Battery was dead so I went to change it - took air/oil filter vent stack off to open hood ....... and...

Hey guys, So I did create a post about this before. At that time I did not have all information. So there is a neighbor that lives nearby that said he may be interested in selling his Ford 1700...

Anyone know of a steering assist kit or power steering kit for a 1700? I’m aware of the Jackson but $1900 is a hard pill to swallow. My new box that I got from kumar bros last 4 months and broke.

Was out doing my normal brush hogging, all going fine/normal, when I went over a section of raise up dirt that bogged down the machine. I assumed it was just a small mound and after restarting...

I recently picked up a 1980 Ford 1700 2wd with nearly 3300 hours to mess around with. The sound of the 2-cyl diesel is unique! It seem to run and shift fine. Some questions: 1. The turnbuckles on...

the radiator screen on my 1980 Ford 1700 is rotten and trying to pry the metal frame a part to just replace the screen is not working. I have found a couple of complete screens on line but at 120...

I've just inherited a 1980 Ford 1700 4WD and I have a couple of issues that I'm hoping someone can help me with. This one is about the diff lock. I just noticed that the lever for engaging the...

I've just inherited a 1980 Ford 1700 4WD and I have a couple of issues that I'm hoping someone can help me with. The first is the cooling system. It seemed to be fine when I was plowing snow, but...

Anyone have experience with replacing rubber mounts/spacers for the step plates; or have suggestions on alternatives to secure the step plates. Will appreciate any thoughts.

Can anyone tell me the difference between a Ford 758 758a 758b and 758c backhoes attachments. Thanks

Hey guys, So this community has been awesome so far and things are getting more complicated. As some of you may know my neighbor just gifted me an old 2WD Ford 1210 and I am deciding what to do...

Hi, Very inexperienced old tractor owner. Trying to get the rim off the center piece of the rear wheel to replace it. I am not familiar with the kind of nuts holding the piece on. I know it's...

Ford 1700 tractor stopped I drained gas put new cleaned glow plugs turns over won't start notice no smoke not coming out of stack at all...can ya help me out.

I managed to bust the sump casing assembly (SBA322010100) on the front drive axle, which led to cascading failures within. Found replacements for the casing and bearings, but the drive pinion...

Good morning. I got a new safety switch in last week, but went away for a long weekend. I opened up the trans cover this AM, and I believe I knocked a spring in the tranny well. Going to try...

Seemingly overnight, my awesome 1700: Had a harder time than normal starting Actually seemed to 'catch' and run okay, but, just wouldn't get it's idle or rpms up It surged for a minute or two and...

Hi everyone I have a ford 1700 that I use in comerical service for my sawmilling and custom farming operation. Recently while brush cutting I noticed that the pto shaft had some in/ out play...

Crossing over from my starter/ignition getting sorted out, tracing wires and finding loose ends. I'm at the fuse block and finding some things that I'd like to make sure they get plugged in...

Hi All, I have a 1979 Ford 1700 4wd. Was bush-hogging and tractor began to lose power and eventually stopped. I was low on diesel and may have run out, but not sure. I did refill, but when i turn...

Hi All, I have a 1979 Ford 1700 4wd. Was bush-hogging and tractor began to lose power and eventually stopped. I was low on diesel and may have run out, but not sure. I did refill, but when i...

Hi. New to site. Had to replAce a shift spring. Drained fluid,inspected gears ok. Replaced all spring’s and balls and fluid. Gears shift without clutch. When startedruns great hydraulics work and...

I have owned my Ford 1700 since 1972. Today the check engine light came on for the first time. (not the battery light). The engine oil is full. Any ideas on what the problem might be? I realize...

I bought a Ford 1700 with around 850 hours about ten years ago. About four years ago the water pump went out on me. I replaced it and decided to do a top to bottom service on it. I found that...

I have a Ford 1700 Farm tractor 4X4 that I bought to repair and use. The previous owner told me the clutch went out on the tractor. I started looking for anything else that could be the problem. I...

I have a 1980 Ford 1700 tractor. I just acquired a 3 Point Hitch Tractor Supply Log Splitter. On my tractor if you are facing it from the back, on the right hand side under the seat, there is a...

Hey everyone. I have an 1981 ford 1700 that is very hard to start. At -2 degree celcius it can take me about an hour of cranking to start. With 2 magnetic block heater and the in line pipe heater...

I have a 1980 Ford 1700. I am having a hard time locating a rear rim. 10x24. Is there any type of interchangeable rim ( single piece) or combination with center that is easier to find. I...

I hope someone can help! I have a ford 1700 2cylinder diesel tractor that has sat up nearly 10 years. After installing a new battery and freed up a cam inside the injector pump, I was able to get...

Hi, Had a question. I have an old Ford 1700 tractor. I let it set for a year after the battery died. Been trying to get it started. Found out the starter was shot. Replaced it. After...

Is there a spec for the head bolt that goes into the block on the 1700. I know the nuts get torqued to 107 lbs but what about the bolts into the head.

Hopefully finishing up a rebuild on my ford 1700. All timing marks are right on. Had fuel injector rebuilt also. Before l put the head on l wanted to see when the fuel is injected to the...

Hi all! I'm considering a local 1985 Ford 1700 w/ loader and augur and 1300 hours as a first tractor for my 10 acre plot that needs some light clearing and maintenance. I'm just completely lost...

I was changing the headlight bulb in my 79 1700 ford. The retaining clips fell out. How does it go back together? Anyone have a diagram ?

Continuing my big "tune up" maintenance, and today is oil change day, but not finding this oil filter noted above. A regional tractor parts shop says there's a New Holland number (but they didn't...

Hi all, I'm about to replace many of the hydro hoses on my Ford 1700 and, especially on the shorter ones, am noticing that when I try to loosen the securing threads ...the hose resists mightily...

Well its been a long road with this tractor, through many glow plugs, a rebuilt fuel injector pump, rebuilt injectors, fixed crack in head and reground valves, motor taken out and rebuilt and new...

How do you get the bulb out of the headlight on a Ford 1700? the headlights are kinda fragile. The I can twist the bulb and feel it click, but it doesn't come out. Do you have to take the front...

So this happened out in the field the other day after I turned the tractor off to brush of the radiator. When I went to get back on, the tractor wouldn't start. Didn't even try to crank, but...

Some may remember me talking about my neighbors tractor that belonged to her father and I had tried to buy, well back in Dec 2020 she decided to take me up on my 2 year old offer and sale it to...

Hello all. I've got a Ford 1700 with no lift on the 3pt hitch. My grandfather bought it new and I've used it for the last 20 years and has been a great tractor. Anyway, It went from working...

So after mowing for about 4 hours this weekend, my 1700 began to develop a 3point problem. The 3-pt was no longer holding up the bush hog. If I fiddled with the controls a bit, it would lift...

I need a rim for a Ford 1700 in Southern Michigan

Looking for a rim for a Ford 1700, 1977 in Southern Michigan . It is a six lug on the center piece, and 4 bolt from rim to center piece, has 12.4 - 24 turf tire on it now.

Anyone here ever had their (3pt) lift control spool valve apart? After replacing my 3pt lift cylinder seal and then redoing the seals in the hydraulic pump to no avail, the only place left to turn...

I am looking for a couple of front axle parts for my Ford 1700 4wd. New or used Coupler: SBA398380020 joint Assy. SBA326240240 drive pinion Please reply if you might know where I can purchase...

Replacing the seal on my 3pt cylinder piston, old one came off in pieces. Noticed the piston head that moves in the cylinder has a couple deep scores in it. Before the seal entirely failed the 3pt...

Hi Everyone, I recently purchased my first tractor, a Ford 1700 with about 2100 hours. The engine oil looked very dirty so I decided to go through and do all the maintenance items assuming the...

I am helping a friend of mine get a Ford 1700 he recently purchased up and running. Its a 2 cylinder diesel, the previous owners bypassed the fuel filter (it's missing the filter cup and element)...

Good afternoon, had my head sent out to be welded due to cracks around the combustion chamber. looked real nice when I got it back . I installed it with the service manual so it should be right...

Installed new head due to cracks, installed in cold temp,just my luck. The install went great, got the motor warmed up with a torpedo heater. Started up for about 30 seconds and stopped, let it...

Looks like my head gasket is leaking before the thermostat opens. After it opens the lead stops. How hard a repair is this for an average person? I just replaced the water pump, the thermostat...

Hi All, First, I'm a complete diesel tractor noob, but I'm handy! This tractor hasn't been in use for 5-6 years. I've drained the gas, changed the oil, new glow plugs, new battery and drained the...

I've read the other posts on this topic. I changed the seals on the piston and tried adjusting the position control link. The pump makes hydraulic pressure. When I move the lever for the auxiliary...

Hi All! So, New tractor, replaced the clutch, got the loader back on and hooked up the battery backwards (oops!). Let the smoke out of the alternator, so bought a new one. Replaced the...

I am looking for a couple of front axle parts for my Ford 1700 4wd, used would be nice! SBA398380020 Joint Assembly SBA326240240 Drive Pinion Could you please let me know if you know of anyone...

Any problem with using rubber fuel line to replace the leak off line between the two injectors? If I replace this line, will I have to bleed the system? Will appreciate any information. JLW

looked at all of the threads i could find on the hydraulics, very informative. another lift problem i am afraid. usually the lifts on all my tractors have blocked screens. not this time. so after...

I had to remove my injector pump to send away to rebuild. While the pump was away the tractor was moved and the engine was turned over. I re-installed the pump but now the engine will not start...

Trying to tinker with a 1980 Ford 1700 I'm looking to pick up from a friend. Replaced the starter solenoid and got it turning over. Fluids and all that changed already, injector pump oil as well...

I am looking at a Ford 1700 that has a FEL, structurally everything seems solid although most of the paint is gone but it looks like a Ford 770. The loader needs hooked up and the lines need...

Looking at a Ford 1700 that a friend is selling. It was his father-in-laws, he is helping his mother in law clean the place up and get rid of stuff. Engine is free, needs a bit of wiring redone...

Inside the pressure relief valve on my ford 1700, what all parts are supposed to be in there? Specifically, is the little cone shaped piece on the end of the spring supposed to seat in something...

Can anybody tell me what type of hydraulic fluid my Ford 1700 takes? I see some that says its compatible to 10w30, and some "Ford tractor hydraulic/ transmission fluid" that says its 90w.

I found out that I need a new rebuilt engine does anyone know of a company that has reasonable prices for rebuilt engines? The crankshaft is bad.

Hi Again! Planning on the clutch split this weekend, and figured I'd redo all the oil while I'm at it. I picked up 2.5gal 14w30 Rotella T4 (I THINK that will work?) And I have 5 gal of Napa...

I have checked the injector pump and can see that the throttle is moving freely but it does not move the cams in the injector pump. I have taken the side cover off and can see the spring looks ok...

Hi All! I was running my 1983 Ford 1700 the other day, when I heard a crashing noise. I shut the tractor off immediately, and discovered the Crankshaft pulley had lost it's retaining bolt, and...

Good morning l sure hope everyone is doing well, l own a Ford 1700 that takes 15w40 shell Rotella, that's what the previous owner did also. Would it hurt to use Shell 10w30 synthetic blend instead...

sorry for the double post. I posted this in the hydraulics forum with no response. Figured I'd try here. First let me say that this is my brothers tractor. I borrow it from time to time to mow...

First let me say that this is my brothers tractor. I borrow it from time to time to mow our (mine and his)hunting property. I'm working on it because I'm more motivated to get it done and I need...

Any easy way to check injection pump timing on the ford 1700. Found some good info on here but can anyone explain how to open up a thumbnails to see the picture on this site

Hello, getting cooped up at home and making work for myself. Decide to do some p.ms on the Ford 1700. Anyone know what is a good compression number for the cylinders. I tested them and they are...

Hello, since we are stuck at home trying not to catch the coronavirus decided to do some pm work on the 1700. In the process had to remove the hydraulic pump to get at the fuel injector pump. Now...

Hello, l own a Ford 1700 tractor, nice tractor but its eating glow plugs. I get about 4 uses out of them and they burned out. All electrical is good and ignition switch checks out. Would there be...

Use tractor and starting to notice when going up a very slight upgrade or pushing snow tractor tires crawl to a stop in 2and3rd gear. I dont notice the engine working harder. This tractor was like...

I bought my ford 1700 last year. I'm starting to think the battery is undersized. Its the size of a car battery but the battery stand is way bigger. Seems when l use the glow plugs at first it...

Hello From snowy Green bay. Having issues with glow plugs burning out after a couple of starts. I did some looking around and l have about 9to10 volts going to the plugs when turning the key to...

Hi All, I'm a little confused as to what type of oil to put in my machine. Reading owners manual shows 10w30, 10w40 for year round use OR 10W for severe cold below 32, 20W for winter use between...

Hello. First time post, Starting to have an issue with my Ford 1700 starting. Temp is 60 degrees out. Engine cranks over good and have exaust coming from the stack when Turning it over but don't...

Anyone have a problem with tractor not turning over. New starter, solenoid, and battery. When trying to turn over the solenoid smokes as well as the positive battery terminal? Anyone have this...

Similar models per the FO-44 manual, may include 1100, 1110, 1200, 1210, 1300, 1310, 1500, 1510, 1700, 1710, 1900, 1910, 2110. I have a Ford 1700 with a power steering option by duBro, a...

My first post y'all, hopefully I manage to do it correctly. I've got a Ford 1700 with a 2 cylinder diesel, firing order 2-1, with 2 marks on the pulley, the first for injection timing, the second...

I have a 2wd 1700 with rear diamond tread tires (13.6-16), and I would like to get increased traction when pulling, plowing, and similar. I have no steep inclines/declines, but the ground is quite...

My Ford 1700 is equipped with remote port but will only operate when the 3 point is raised. I need to be able to operate the 3 point and the remote separately. I have debated between installing a...

Hi All- I have a 4WD Ford 1700 that I need to replace the clutch on. This is my first time doing a clutch split on a tractor. I have the I and T manual and followed all the steps and have all...

I managed to grind up the steering shaft and ball nut assembly on my Ford 1700. Anyone parting one out who would be willing to get me either these two internal parts, or if more convenient, the...

My hydraulic pump quit and I got the rebuild kit from NH. I put some witness marks so it goes together the same. Everything looks worn. I'm not sure how it goes back together as the plastic pieces...

My hydraulic pump quit and I got the rebuild kit from NH. I put some witness marks so it goes together the same. Everything looks worn. Im not sure how it goes back together as the plastic...

i need a front rim for my tractor mine was broken and reweld an its not straight

I have 1700 Ford with black oil coming out one of the exhaust ports, no smoke, changed valve seals, still coming out. I read on the forum before I became a member. someone had this same problem...

I just got my 1700 back together and now it boges down when I go in to the top gear of the trans and when I us the pro and hit a big clump of grass is it the injector or injection pump

I replaced my shifter assembly due to a broken shifter. The knob broke off. When I removed the assembly the detent springs fell out and I didn't realize it until later. I bought 4 new...

I've got a Ford 1700 that drains the battery when it sits. (I've actually got two Ford 1700's, one is for parts. The wiring is similar between the two, so I can compare the wiring and/or swap...

Hi All, Lately I have been very busy at work and constantly traveling and very little time to check the forum. Just saw several PMs that I did not see early enough to respond. Sorry for the late...

I have just recently purchased a 1979 Ford 1700 tractor with 1680 hours . It's in good condition but I want to service it before using it this summer for bush hogging etc. My question for you...

I have just recently purchased a 1979 Ford 1700 tractor with 1680 hours . It's in good condition but I want to service it before using it this summer for bush hogging etc. My question for you...

Hi all, My great ol' 1983 Ford 1700 is telling me I should be in the market for a new Hydro control "lever" setup. I have the "2 lever" control today (boom - up/down, bucket - roll up/down) and...

The mounting bracket where the FEL attaches to the body of the trailer (New Holland (19SW1814) - FORD LOADER 15 & 17 TRACTOR (1/79-12/84) Parts Diagrams - see part 6 in the diagram) is cracked...

I have a Compact Ford 1700 4x4 needing new rear tires. It came with 4 ply AG tires. I had them filled with fluid and the rims are badly rusted. Need suggestions about ply ratings for...

i was wondering do i have to buy a used block cause mine broke the bottom of the skirt out on one side

Hi, I am in need of some advice about where to purchase pieces for the voltage regulator/help identifying what I need. I am new to being in charge of caring for a fleet of tractors. We have a...

Anyone have a reliable source for an aftermarket muffler for a Ford 1700(North American). OEM ones are over $300.00

was wondering if a backhoe from a ford 1300 would fit on the 1700 ford for sure. under the attachments on tractor specs it lists the 757 on the 1300 ford and the 757 and 758 for the 1700 ford the...

i ran out of hydraulics on my 3 pt lift system,i don't remember what brand to use what would be the best hydraulic oil to put back into the 3 pt system tank,i looked at the old manual it says 5.3...

need some help finding parts for my ford 1700 i need a block, crankshaft, and one rod or i just need a short block

Hello, I just bought a Ford 1700 4wd, with a loader. After getting it home and running it for awhile I noticed a leak from the power steering cylinder. I have been looking for information to fix...

Okay guys here we go again, posted a while back about my son's 1939 Ford 9N that he inherited and turned out it has a cracked block. I was telling my neighbor about it and they have a 1980 Ford...

I purchased a 1978 Ford 1700 tractor 4wd. I need a radiator cap for it. I found plenty of caps for ford tractors but I could not locate one for the 1700. I don't even know what PSi cap to...

Greetings JC, I have a Ford 1700. The tractor has 560 hours and has been sitting for the past 10 years. I bought it at an estate auction. The hydraulics worked very sporadically. I drained the...

Greeting Forum members. I have a Ford 1700 tractor that has been sitting for approx. 10 years or so. 550 hours on meter. It starts up nicely and is very dependable. The hydraulics on the other...

Hi Folks, Just bought my first tractor ! Bucket list thing :) I live in upstate New York, just North of Albany by about 15 miles. Originally from the UK from 20 years back. Could never of had a...

I have a ford 1700 with 1300 hours on it. I changed the oil the other day and started the engine to fill the filter then shut it off to check level and when I pulled the dip stick I heard a rush...

My 1700 3pt will not raise I'm assuming it's the pump we already took the screen out and cleaned it and put new fluid and that didn't help when it's cold out it'll work some when the oil is thick...

HELLO, I am starting another thread on this because the old link seems to be a dead end. Does anyone have a source for the 1700 axle fix?? (machine shop new) I saw a listing on Ebay a couple...

I am looking for left and possibly right lower kingpins for my 1980 Ford 1700 4wd tractor. I believe these are the correct part numbers: SBA330300471 kingpin L/H lower SBA330300491...

I have a Ag-Tech AT-720 FEL for 1982 Ford 1700 and I'm trying to rebuild the lift and bucket hydraulic cylinders. I took the cylinders to a local hydraulic shop and they noticed that one of the...

Team Looking at a local Ford 1700 for some small work I have to do on my place. Currently has turf tires in the front. Can I swap out ag rims and tires or is there actually a differant hub /...

Have a 1700 4x4 with loader, and one of the front (badly weather-checked) tires gave out this past weekend. Was surprised to see they are only 4 ply rated around 750 lbs load. Am hoping to...

Does anyone know where I can find a manual steering gearbox that will fit my ford 1700 (Japanese model)? I bought one several months back that I believe came off of some other type of compact...

Where is the best place to get good deal on loader bucked assembly for Ford 1700 tractor? Have looked locally (Sarasota Fl) area, to no avail. Any ideas much appreciated. Ron

I am looking for a couple of front axle parts for my Ford 1700 4wd CUT. New or used Coupler: SBA398380020 joint Assy. SBA326240240 drive pinion Please reply if you might know where I...

Thought I would toss this out in hopes one of you can see what I am overlooking. I installed a 10 micron hydraulic filter on my tractor and it proceeded to blow the filters within doing 6 lifts...

I had recently looked at a new Kubota and liked the additional step offered on newer tractors. My knees aren't what they used to be, so I added the step below to my 1700. I put it at 13" vs 20"of...

I was going to replace the springs on the shift levers, so was looking at the parts diagram below from Messicks. I noticed the part #47 shown as a seal. I've had hydraulic fluid issues with this...

I am seriously considering using a power beyond valve on my tractor so that the front end loader and the three-point can be used at the same time. My loader is using the accessory port under the...

Greetings gentlemen, My pastor bought a used Ford 1700 or 1710 tractor (I'm not sure which model exactly) about three years ago. This past summer he started having issues with his 3 point hitch...

I worked on this about five years ago, have a leak, and can't remember the details unfortunately. I have a basic question for anyone familiar with the adjusting components. ITT shop manual says...

I have a ford 1700 tractor 770 front end loader. My controls for the loader started acting up so I looked into getting mine rebuilt or buying a new one. From past experience buying parts for my...

I thought of selling my Ford 1700 for no other reason than accessibility. With size 14 boots and a gut to match, it is not the easiest thing to get in and out of. It has plenty of horsepower for...

Ford 1700 4wd manual steering, 770 front end loader Does anyone know of any places that sells a steering gearbox rebuild kit and / or sells an already rebuilt gearbox? Also looking for left side...

Hello All, I am considering purchasing a Ford 1700 that is listed for $3,000 obro. I don't know a lot about it yet but wanted to see what the general feeling was concerning price. It is 4wd but...

I know im new and yes ive searched for my exact problem and haven't had any luck. so ive hard my tractor for prolly a year now and its became very hard to start within the past 6 months even when...

I am the 2nd owner of this tractor for the past 20 years and have been able to do my own repairs(starter,water pump, fuel system etc.) Now this steering system is leaking and I assume it is...

WONT RAISE DISC OR LIFTS WHEN IT FEELS LIKE IT. NEED TO KNOW WHERE FILTER IS AND HOW TO RE PLACE IT?THANKS ANY HELPS IS APPRECIATED

Hi there, I just picked up a Ford 1700 not sure what year (79-82?) 4x4 with duall 155 front loader. I also found a good by on a Land Pride 1248 rotary cutter and 48" Henry j rotavator. I'm hoping...

Having some problems, 3 point that will raise and lower but when it is stopped I hear the relief valve. no matter where its stopped. After a short while 5 min. or less it is real bad and just...

Hello fellow tractor folks! Im looking for help locating the seal for my PTO. Does anyone know where to purchase this? Also what oil to refill with. Thank you in advance.

I am trying to change the oil in my Ford 1700 fuel injector pump, but can't remove the fill plug/breather cap to pour in the oil. The cap does not screw off--it just spins when I twist it. I...

Greetings all! Long time guest reader, first, well, second time poster. I have been reading about Ford 1700's in various capacities over the last 8+ months. My wife and I have built our dream...

I'm getting ready to fab up a subframe for my Ford 1700 / LW-6 backhoe. Thinking about 2x2 or 2x3 tubing with 5/16 wall. Seen some where it was flat plate but tubing might weld better. Thanks! Brian

I've got a adapter block on my 1700 that I have hooked to a backhoe. Well I drug home a front loader and need another circuit. I was hoping to be able to 'stack' the adapter blocks to have two...

My 79 1700's loader is working very very slowly and only if I give it a little gas. So far I cleaned hydraulic filter and changed fluid, replaced the seals in the hydraulic pump and checked the...

I have a 1700 tractor that has evidence of having a front loader installed at one time. I just picked up a LW-6 backhoe and I was thinking about tapping into the 1700 hydraulics. But exactly...

How much weight can I carry on the back end / 3 point on my 1700 4wd? I would like to get a small backhoe attachment but I'm concerned about the weight. Brian

Hello Forum, I bought a Ford 1700 tractor with 550 hours on the meter. It has been sitting for around 10 years per sellers family. The engine started up fairly easy and runs great. The problem...

Howdy, Just picked up a 1700(4WD) and it needs front tires. I have ag tires on my 1600(2WD) and the wife won't left me go any where off the dirt. So the 1700 with turfs should allow me more...

Hello Everyone I am another new guy, with all kinds of questions. I have posted a short intro in the introduction forum for those who are interested. I own a 1983 Ford 1700 tractor for the past...

Has anyone tried using automotive tires for the front tires on the Ford 1700 tractor? If so, what size tire/rim, any modifications necessary?

Happy Thanksgiving! While plowing the 15" of snow that fell in New England last night, the Ford 1700 died quickly with no notice and no load. I thought it may be fuel, but after review, that was...

First time buyer & found a Ford 1700 with roll over gannon box, loader, & the 757 back hoe attachment that he says works but needs some attention, not sure of the year or the hours just yet as I...

Had this thing for about 4 years. I has taken a little work but I've kept it running till now. When I turn the key I get a little rotation on the motor ~30 to 60 degrees or less. I've charged...

Well I had my first experience with a stuck clutch. I had my tractor over at my mothers doing a little work and I had to leave it outside uncovered. It rained and was a week later before I got...

I'm a novice. I was trying to hook up a three point backhoe to which I've extended the lines 10 feet to help get it into position. I'm standing there and hear the sound of the tractor change. I...

I have a Ford 1700 and I cleaned the filter changed the fluid. 3pt does not work at all no movement or anything. Pulled the cylinder out and turned tractor over and all the fluid empties back into...

I recently picked up a Ford 1700 which had been sitting. New fluids and a hot battery fired it right up. The older gentleman I bought it from told me they hydraulic lift worked fine until his son...

The water pump went out on my Ford 1700 and while I had it in the shop, I decided to change all of the fluids and filters. I drained the hydraulic fluid/gear oil and it was a little dirty but not...

Hi I am new to tractors. I have a decent knowledge of motors but am totally new to diesel. I just picked up a 1700 2wd that's in decent shape. It starts up perfectly has no smoke from the exhaust...

I need a new bucket for my Ford 770 loader. What is quick attach all about,what all is involved welding ect.:)

The hydraulics on my Ford 1700 tractor work fine when I first start it up but after it warms up they slow down and quit working. Every thing was ok one day and the next day I drove the tractor...

I sold my 1979 Ford 1700 4WD. I had broken an axle and after looking for parts and the cost I decided I would make it myself. I made two axles at the time. I still have one and would like to sell...

I been reading posts as a guest for years (this site is great!) but finally decided to join and post for myself. I have read several posts about this problem but I had a few questions I hope you...

Hi all, I searched and couldn't find any posts about this issue: My '83 Ford 1700 has been great since I inherited it about a year ago. GREAT machine. Occasionally, it would be a challenge to...

I purchased a new water pump and was hoping to replace the thermostat, but when I took old pump and radiator hoses off, including port between upper hose and block, there was no thermostat...

This tractor only has the warning light, no oil pressure gauge, but light seems to be operating correctly. Goes out immediately when tractor is started cold and stays out at even lowest idle...

Has anyone added power steering to a ford 1700 4 wd Tractor?

Oil was coming out the top of the steering column. I am attempting to replace the seal at the bottom of the steering column. I have everything loose I think but the outer tube will not come up off...

Can someone please educate me on the following? When you grease the front king pins, do you keep adding grease until is squeezes out near the ball? I've put at least a tube and half of grease, so...

Hello Everyone, I have been using TBN for research for several months now and this place is awesome. I am currently looking at a Ford 1700 4WD with FEL, 4' shredder, galvanized box blade and 16'...

My ford 1700 started leaking Hydraulic oil from the top of the steering column. I took off the steering wheel disconnected the dash wiring and removed the 3 bolts holding the column down. The...

Hi everyone, I am new to the forum....thank you all in advance for any wisdom or advice you can pass along. Last fall I bought a very nice low hour (550hr) 1980 Ford 1700 4wd. It's in great...

I have a ford 1700 with a 770 loader. I would like to know the GPM for the hydraulic valve ( 2 spool ) that came with that model tractor. Had the old one rebuilt but it still leaks. now I am...

After 960 hours and over 30 years my super Ford 1700 tractor's electrical warning light has started a steady flashing, on and off. The batery is fine, fully charged, all connections sound and...

I have a ford 1700 4 * 4 iso 68 hydraulic oil is hot and not lenvanta well and do not get the trans fluid 80w90 I place him?

nesecito help I have a 1700 ford tractor recently installed by hydraulic steering rear linkage and now 3 pts up which can be very slow please help?

Looks like I have to replace my clutch. I have looked all over this site to find out how to tell if this tractor has a single or double clutch but have not found. It is a 1982 model, Ford 1700...

I am trying to help a friend with a Ford 1700 diesel tractor. I know it was built by Shibaura. He says it has issues with the wiring being bad behind the dash. Can anyone post a wiring diagram...

Hi, I new to the site but very interested in tractors. I have a small farm in PEI Canada and I'm looking for a compact tractor to basically play around with. What do you think of the Ford...

Alright guys. I have read some forums on this site and other sites online about the axle hubs on this particular year tractor having a design flaw and being too small from the factory. I have...

The valve that works my loader also runs the 3 point hitch. It's leaking hydraulic fluid and I can't read the brand or part number. Northern Tool has some valves but I'm not sure if any of them...

My hydraulics are not working correctly (very slow) and from the past I know it needs the filter and fluid changed in the hydraulics. Can anyone tell me where to do this on the Ford 1700?

Hi Everyone I am after a bit of advice I am looking at buying a Ford 1700 tractor, it however has a sticking clutch. Am I crazy for even considering it or is the fix not to hard or expensive...

Hey guys, Going to start fabricating a snow plow setup for my Ford 1700 and am interested how some of you guys have done yours. I have a loader setup and am wondering whether it is better to use...

FORD 1700 TRACTOR FOR PARTS Not mine for sale, just something I saw on craigslist. Steve

Gannon cylinder for 3pt. Hitch

Any idea what is a reasonable price to put on a Ford 1700 tractor? Has not run in some time, has 4WD, bucket loader with good hoses and solid metal. Wheels rusted bigtime. Rubber shot. 3 pt...

Hey guys, Last year I purchased my first home and piece of property. Figured that I needed a tractor to start working my property, plow snow, mow my huge yard, and to just have a useful tool and...

i have a ford 1700 series 2 wd. my clutch linkage rod has started vibrating in and out from the engine/tranny block. it moves about 3/8 of an inch either way. it does weather th clucth is engaged...

Tractor has been running absolutely perfect, and I decided to do some preventive maintenance by replacing the oil in the fuel injection pump. This 1700 only has 400 hours on it. I have one of...

Hi all, This is a repost in the Ford section of the original post I placed in the repairs section. Ford 1700 starting problems I just bought a "slightly" used 1979 Ford 1700 tractor. It had some...

Hi all, I just bought a "slightly" used 1979 Ford 1700 tractor. It had some obvious things wrong and some not so obvious. I've had to replace the battery and will have to put all four tires on...

Has anyone looked-for/found a "close enough" replacement radiator for a Ford 1700? I see them on e-bay, but don't really want to pay $475+ for one (last radiator I bought was for a Pontiac...

Tractor was running great today with no issues whatsoever.Turned it off to do some yard work and then went to restart it nothing would happen. Battery is good, horn,lights and engine block heater...

Hi All, My hydraulic fluid is pretty low - is it typical to "lose" fluid over time, does it kindof cook away? (this 1983 Ford 1700 is new to me so I don't know it intimately yet). Anyhow...

Has anyone out there attempted to add power steering to a Ford 1700? I saw an old thread from 2007 asking as well, but it didn't appear to go anywhere. Just curious what the recommended specs...

Does anyone know how to remove the shifter to replace the seal? I removed the boot and shifter pin, but the shifter won't come out. Obviously in need of a manual. Thanks, Mack

If you have a manual or just know, please tell what oil is recommended for the fuel pump. Thanks

Just bought a house and inherited a 1982 Ford 1700 with 1500 hours on it. It actually runs great, but when climbing any kind of incline or running my 5 foot finish mower at has absolutely no get...

Hi all, I recently inherited an '83 Ford 1700 and love it. What a great yard tractor. While doing light work the other day, I thought I noticed steam coming up from the front of the tractor. I...

hi guys Broke my front LH axle the other day, was wondering if any one has had any luck having one repaired or fabricated by a machine shop. I have searched all over at salvage yards with no...

Hello I was driving to tractor fixing some spots in my long driveway when the front wheel broke off.....have looked everywhere to find a replacement. Has anyone ever had on repaired or fabricated...

Just a quick question on the differential lock pedal on the Ford 1700. Had 17 inches of wet heavy snow last week and used the 1700 (4x4 with loader) to clear the 3' drift covering the neighbors...

i tried to search for how to rebuild a fuel injector pump on my 1984 ford 1700 tractor. would like to find someone that can email to me or tell me where i can find the insturctions to rebuild it ...

Hello, I've only owned this tractor for a week now, already I have benifited from the post in the forums. Thanks to all

I have a ford 1700 2wd with fel. The hydraulics were fin but milky so i changed the fluid and cleaned the screen and refilled. Now the rear arms are fast and strong as it always is but my loader...

hello all. i have purchased my very first tractor a ford 1700 4wd with 770 loader and meteor blower. my question is about the 3 pth .should this have down pressure? i find that the blower will...

I opened the bleeders and cleaned the filter, helped a bit, but still not as powerful as it once was. Any ideas on what could be causing this? Any help appreciated.

Would like some information on how to remove the drive line on my ford 1700 4x4. Don't want to screw it up.:confused2:

I need to replace the clutch on my Ford 1700 Tractor. It is stuck and will not disengage. I have lots of experience on clutch and transmission repair on cars and trucks, but have never split a...

All, I have the above tractor and need the sway control parts to prevent my 3 point bars from swinging causing the implements to hit the tires. Messicks has the parts but are really expensive...

Haven't used the 3 point in about 6 weeks and when I went to put on a sprayer I find I have no function on the hydraulics. The gauge installed by the up down speed control dial thing shows 0. I...

Does anyone out there have a 1700 with a cab? Was hoping that if someone has one, they might be able to provide some pictures. Searched the internet and saw one canvas cab and maybe two steel...

Hello all,I am looking for a creeper gear kit for my Ford 1700 4x4,NH does'nt supply it anymore but hopefully someone out there might have one or know where to find one.Thanks

I have a 1700 that I noticed does not have an inline fuel filter which I know is a bad thing for diesels to not have. Can someone recommend a fuel filter assembly and maybe even a link? I would...

Hello there,just hooked up my new snowblower to my tractor to clean a path down to the barn and realized that 1st gear reverse is too fast,2 shear bolts later.In my jensale manual I see that a...

Fired up the 1700 today and was letting it warm up a bit when I noticed a puddle of red fluid forming beneath it. Freaked out when it appeared to be spraying out of the back plate on the injector...

Curious how the float position is expected to act on a 770 loader. I've noticed when using the loader that raising and lowering it is a bit scary because the float position can easily be...

Hi All, My girlfriend has a Ford 1700 with a 770 FEL. This tractor has been a winter workhorse for the three years she has owned it. This year, the hydraulics failed to operate when she was...

Hello, all. First post as a new member, but i have been lurking here for a couple of years. I have learned a lot from this forum and you all have helped me to make decisions regarding my...

I'm asking this to help a computer-less friend sell his used 1700. The machine has around 1900 hours and the 3 pt hitch does not "work". The tires and rims are shot bigtime. It is 4WD and has good...

I recently purchased a 1980 ford 1700 tractor which has been sitting in a garage since the previous owner passed away (approx 11 yrs ) Is there anything special I should do as not to cause any...

Ok, I haven't used the tractor for 6 weeks. Last job was tilling and parked in garage. Tried to start today. Turn key only hear click sound comming from the right side area. Starter is on...

Have the parts machine for sale. Has a solid Ford loader and motor has 1900 hours. Good 3 pt. Rims tired, front end OK, with 4WD. Any idea what such a unit might be worth to a prospective buyer?

I need to know the lift capacity of the 3pt. (cat 1) for a Ford 1700 (23hp. tractor wt. 2326 lbs.). Tractor Supply sells a 3pt. hay spear for a cat 1, but I'm concerned about the lifting capacity...

this spring i bought a 1980 something Ford 1700 tractor with 1290 hrs. Came with FEL, 3point farmking mower and tiller (5'). This thing worked great for the first 6 hours. Cut grass in no time...

hi guys...we broke the left front axle at the hub(common problem?).found an updated axle(better,stronger,faster?)for 1200 but since money is an issue(when isnt it?)i was curious to know if anyone...

My PTO atachments don't stay steady - they move up and down a couple of inches on their own. It seems worse after running a while. Anybody have any quick and dirty ideas to try? The fluid is fine...

Hello would anyone know if a cab from A ford 3910. Could be fitted to a ford 1700. Tractor. Thanks I'm advance.

How does the fan pulley mount to the water pump? The pulley assembly on my tractor has some lateral slack. Is there a way to correct this? Is it an issue that I need to correct? I see what...

Hi all, I'm in the process of buying my first tractor, a 1980 ford 1700. I am knowingly buying it without working headlights. The seller seems to think the headlight switch is burned out, seems...

I have a Ford 1700 diesel tractor that will crank but won't start. My neighbor told me that he thought the "fuel solenoid" was bad. He showed me where it was at and said it costs about $120 to...

I am working on a 1980 Ford 1700 4WD steering box. I am trrying to make sure of which sector shaft it takes. I see that they list a couple different sizes.

Hi, everyone. I have looked at this site and forum sence i bought a Ford 1700 off ebay for $2500. The tractor has. New paint and looks very good with 3047 hr. The engne runs and everything works...

Hello, I have a ford 1700 tractor with a front end loader I am trying to get fixed up. The hydraulic 3pt lift works fine without anything on it, but my problem is even if I put as little as...

Hi everyone! I just purchased a 1 owner ford 1700 tractor with a front end loader. It had been sitting for about 2 years in a open barn. The guy I bought it form said it had a burnt valve so he...

I was looking for some help on an issue I'm having with my Ford 1700 tractor. I'm new to the tractor world and new to posting on forums so please bear with me. I've found this site to be very...

I've searched on this and haven't seen a good picture with which to compare mine. I had assumed water in the hydraulic fluid would just appear milky, and not coagulate like this. It cleans pretty...

I'm having a heck of a time finding a fuel filter that fits. I thought this to be a factory setup on a Ford 1700. I've purchased the Fram, the Baldwin, and from the Ford dealer the SBA360720130...

hi fellas, i am looking to purchase a very nice 1700 ford with bucket loader. are these good tractors and how is parts availability? thanks much

I just picked up a Ford 1700 that needed a starter. While I waited, I wanted to start it and move it around, so I tried pull starting it. However, the clutch is slipping. The clutch disk has...

I'm looking for a replacement solenoid for a starter on my Ford 1700. I think it has a Lucas replacement. Neither Napa nor the only starter rebuilding place around here were able to find a...

I have a 1700 that is running hot. I can run it for about an hour before it reaches the boiling over point (30 mins or so if I'm bush hogging). I normally use it to move hay which only takes a few...

Well i recently got a sweet deal on a beat up ford 1700 4wd. It turns out it wasnt locked up but jus has broken 4wd driveshaft. So im goin to try to start on my project of reversing controls and...

Good morning: I'm going to an auction tomorrow to check out a Ford 1700 (2WD). (I know the seller, and I know the tractor has been well cared for.) I checked out the specifications on Tractor...

Hi i recently bought a ford 1700 4wd with bradco loader. I dont need loader for my project

Thinking about adding a remote hydraulic kit for rear implements like a snowblower, woodsplitter or even modifying my rear blade and rake for angle control. Has anyone installed one of the kits...

I would like to mount an electric fan on the radiator so I can reverse it to blow the debri off the screen. The water pump shaft sticks out too far. Is there a w/p with a short shaft or flange to...

Yes a kind of dumb question. The 'label' on the front wheel drive lever (right below the seat) of my 1700 is worn off. Is power to the front wheels engaged when the lever is up, or down?

Hi all, I'm new to the site and tractors for the most part. I have ~5 acres and horses and looking for a tractor to mow, move snow, and manure. My limited budget of around $5K has led me to a...

Hello everyone - a friend has a long drive way and in need of a 4wd tractor wtih a blower. Another friend is selling his Ford 1700 4wd with a front mount blower, I think it may be a Ford 715...

Any chance of someone out there taking some measurements of their PTO guard (grabbed this pic off of the internet)? Length and flared end width/height would be greatly appreciated. Thanks -Neil

When I removed the 770 loader to fix the tractor frame on the 1700, I disconnected one hydro line from control valve and one from the tractor and looped each of them back to close the loop. Then...

Hi. I wanted to thank all of you Ford 1700 guys who have taken the time to document repair work, maintence work, and all of the many hours spent posting threads on these topics. I have recently...

Took possession of a 1700 this past weekend. Originally thought it just needed some loader repairs (broken welds) until my brother noticed the left-side frame. Is this a common break on these...

I just picked up a Ford 1700 4WD that has been sitting for about a year and a half. Story goes the PO was rototilling the neighbor's garden, brought it home, parked it in the drive and started to...

:confused2:My 1700 diesel quit working, I started to pull the pump and screwed up the timing. We got that straightened out however now it overheats about 15 minutes after putting it in gear. It...

My 1700 diesel quit working, I started to pull the pump and screwed up the timing. We got that straightened out however now it overheats about 15 minutes after putting it in gear. It can run 2...

Let me apologize up front for the length of this post. It's my first and I'm afraid I may have gone a bit overboard. I've been fixing up my dad's old 1700 4WD. It's got over 2800 hrs and has...

I am replacing the head gasket on my ford 1700 2 cly. diesel and need to know the pattern to tighten the head bolts and torque.

Any pointers (do's and dont's) when it comes to hauling a Ford 1700 4x4? Will be going to get one in the next 2 or 3 weeks. With the loader I think it will weigh in at around 3,200 lbs or so...

I was having problems with the Hyd system, intermittent, slow to respond; so I changed out the fluid and cleaned the filter. Now,..... It won't work at all. Any ideas. Ken B

My dad and I just bought a 1984 Ford 1700. It has the 2 cylinder diesel and today when we had been using it for about 30 minutes I saw that it was getting hot. We let it cool down and then checked...

My dad and I just bought a 1984 Ford 1700. It has the 2 cylinder diesel and today when we had been using it for about 30 minutes I saw that it was getting hot. We let it cool down and then checked...

Hi... This 1700 will be coming my way in the Spring and I am curious if they have auxiliary hydraulic ports on them. (as you can tell from the picture I didn't get a chance to take a good look at...

After looking around the forum and reading a great deal on the Ford 1700, I thought it would be worthwhile to sign-up and ask my burning question directly: I am in the market for my first...

Can anyone tell me what oil they use in the front differential of thier Ford 4x4 1700? I'm assuming that you use the same as the rear transmission, hydraulic oil? Thanks

I have a 1982 Ford 1700 and was in the process of overhauling the engine and painting the tractor while it's torn apart. Can anyone tell me what color of White is on the fenders and wheels? The...

Just wanted to say thanks for help I recieved on here putting my basket case Ford 1700 back together. I bought the tractor for $1500. The owner had left the head off and mice had built nests in...

Hi, I have owned this Ford 1700 for over a year and it has always has had loose streering wheel. Today I was doing the neighborly thing helping someone move some gravel and leveling it. In the...

I just got a Ford 1700 with a bucket, and would like to find a backhoe for it. Are there any backhoes other than the Ford 757 and 758 that will fit it? I have not found either of those for sale...

I have no working lights or dash gages. I checked fuses, they are ok. I found a thick red wire hanging from the back of the ignition switch. It is a short wire, but I don't know were it goes or if...

Looking at a Ford 1700 with FEL, 4WD, 5 ft ford bush hog and 5 ft blade. Guy wants $4,000, which doesn't seem too bad. Hr meter broke, but he claims it probably has about 4000 hrs on it. Used...

Howdy folks, Here I am with another battle story and associated lessons learned. Hopefully other 1700 owners will be able to avoid the pickle I got myself in:D. I have been working hard to keep...

Just wondering if the Ford 1700 circa 1980 has a live pto.

I have a 1979 Ford 1700. I bought it as a basket case and it have proven to be a real challenge getting in running shape. I managed to get it all together only to find that the hydraulic pump is...

I am trying to correct an overheating problem with my Ford 1700. What temp is the thermostat supposed to open. The radiator is free from debris and I plan to flush and tighten the belt a little...

I am trying to correct an overheating problem with my Ford 1700. What temp is the thermostat supposed to open. The radiator is free from debris and I plan to flush and tighten the belt a little...

Has anyone done this, and how hard is it to do? I have a broken steering box. Fred

Anyone know where I can find a steering box for a Ford 1700? Fred

:(The tractor stalls when the clutch is let out, even with the gearbox in neutral. What may be the cause? It just had a new clutch installed, it was doing this before. Anyone else have this...

Just found this site - looks awesome. I'm an owner of a Ford 1700 with a 770 loader. I recently had it into the dealer to have the clutch replaced. Just got a chance to try it out, and it came...

On my 1700 if you were sitting on the operators seat and look between your legs (insert comment here). There is a adjusting knob. It is mounted on the vertical and the top of it faces forward. it...

Please don't ask how it happened, I really don't know, but the little aluminum dip stick that is (was) attached to the screw plug for the hydraulic oil fell into the gear box and got chewed up...

I am looking for turf tires and rims for my Ford 1700 tractor. I currently have agriculture (AG) tires and rims on the tractor. Tires are almost new and I would be interested in trading them for...

I am tring to get a tractor running for a woman up the road .It is a ford 1700 The problem now is no brakes can they be adjusted the linkage is free and moving. was low on trans fluid filled it...