jd2320 has been idle for a month or so. Starts good, run’s smoothly, but when I try to engage the transmission range lever into either high or low range the engine stalls and quits, Any...

Hey all, I’ve got a JD2320 that won’t start. I had a friend stop by who checked a few things and when he pulled the fuel cutoff solenoid found that the fuel cutoff is stuck in the off position...

I recently replaced drive shaft and output shaft for second time from dreaded u joint failure. All seemed fine after. Today using brush hog… all good, but after period of time cutter was...

Hello all, It's been a LONG time since I posted on it. I am selling my 2011 2320 (which I think I have sold already for $15,750) which includes a 54D mower deck and a 200CX loader with a 4'...

Does anyone have info on replacement for the steering cylinder on JD 2320. I can’t believe John Deere said it’s discontinued.

I was wondering if anyone uses a JD 2320 for snow blowing and mowing? I just purchased a house on 8 acres with about 3 acres of mowable yard and a 572ft paved driveway. Does the tractor have...

Any suggestions

I replaced my alternator on my 2320 and the new alternator that was compatible doesn't have a wire coming out the back. It has the female connector built in the back causing the male in...

Finally got around to replacing the Original Tractor Cab soft cab that came with my 2320. Used 1-1/4 square tube for the frame, safety glass from and rear and lexan on the sides. Retained the top...

I have a Deere 2320 tractor. I'm wondering why the U joints are all non sealed unit's? When was the last time we had to grease the U joints on an automobile? This tractor also has a U joint that...

I started my JD2320 this morning and it ran fine. Went away for a couple of hours and now it fires but won't run after I stop the starter. I've checked all fuses, hoses, fuel filter, etc. I have...

I purchased this tractor last summer without a mid-mower. This summer I purchased a 2015 model year 62D mower deck. I purchased the linkage system and installed the mower deck. It all seemed to...

Under the principle that you should share your mistakes in case others are as careless as you, I just did a little unexpected work on my 2010 JD 2320. Those of you who have these machines know...

Looking at a 2013 John Deere 2320 with loader - no other attachments - no mower - It has less than 80 hrs on it and it very clean and well kept. Ive done my research and see the front u joint can...

Hi, I'm hoping someone may be able to help me. About 5 weeks ago I went to start up the 2320 to mow my lawn, but when I turned the key, I was met with no dash lights and no response from the...

I don't see a leak when operating but when I put it away I get fluid on the floor from one of the connectors. I ordered some Pioneer O rings which may solve the issue. My question- Why would a...

Hello I'm sure this has been discussed numerous times on this forum but I can't find it. I want to install a power beyond for my tractor. Deere wants over 500 dollars for a kit. Just the kit...

I wonder if anyone out there has had a similar problem? The john Deere was bought second hand and has no books with it. I'd like to hear from someone who has had to change the sensor for the...

Here is a link to a short video of a few modifications I made to our 2007 John Deere 2320. Also just testing the new Garmin VIRB X camera I received for Christmas. We have not received very much...

Morning all. Tried to hook up the box blade yesterday, I couldn't get the 3pt lever to move. Messed with it and got the lever to move but the hitch itself won't go down now. Messed with the...

This past winter while removing snow from the driveway I noticed the rear axle locker stopped engaging. I could depress the locker pedal, but no dice as one wheel spins freely. I致e lived without...

I am considering purchasing a 27' airstream that weights 6000 lbs, and I was looking for thoughts on using my John Deere 2320 to move the trailer around in my yard. The hitch weight is 791 lbs for...

Anyone ever have to replace the rear output shaft for the MFWD on a JD2320? The front looks pretty easy but the rear may be more difficult.I have alot of mechanical and electronic experience.(Just...

A friend asked me to diagnose his tractor that he let migrant workers use on his property. The tractor starts, runs and moves but it has no hydraulic power to the FEL or the 3 pt. hitch. He...

Debating 48" or 54". Leaning toward Everything Attachments or Land Pride. Some previous threads touched on this subject but I thought I would post since 54" blades are becoming more widely...

Changed my hydraulic/transmission oil today. The manual said I would find 4 magnets inside the strainer. There were only 2 and they were stuck together. Checked inside the cavity to see if they...

I am now the owner of a 2008 JD 2320. 1 owner with 98 hours. came with a CX200 loader and 5' blade. I will use it for driveway maintenance, hauling firewood, making trails with the use of my...

Morning guy's the output shaft to the front wheels just snaped off the transmission on my 2320. Anyone have this happen and have any repair info? thanx...

Hey Everybody, I am in the process of installing a two spool valve on my JD 2320 so I can have two sets of coupler's at the rear of my tractor for attachments. I know that I need to attach the...

Folks I am trying to find a John Deere 2420 manual. The manual number is OMLVU16740. I purchased my unit used and it did not have one. It used to be available on line from deere to look at but...

Hello, I'm new to this forum. Just wondering what weight and brand synthetic oil everyone would suggest to use for my john deere 2320 compact tractor? I live in North Carolina. Summers are hot...

We have two properties and one JD 2320 tractor. We want to remove our t-posts and put in wood posts for a electric fence. One property has sloped ground in places with hard pack and rock. The...

Hi All, I have the opportunity to purchase a set of fairly new used turf tires and wheels off a John Deere 2720. Would these work on my tractor. I know the clearance my be close, but I have...

I have a JD 2320 with 400 hours on it. Purchased in 2008. Recently the drive shaft U joint failed, snapped the drive shaft off inside the rear end. John Deere and my dealer don't want to know...

Looking for some pointers if anyone can help... I've got a 2320 tractor that won't start. It had overheated earlier in the day when the grille plugged up and I shut it down to let it cool off...

I've just noticed that this spring my 2013 Deere 2320's hydraulics seem weak. I noticed it first when I was moving some dirt, but just thought maybe the dirt was wet and heavier than it was last...

I'm looking at getting a new PTO-driven wood chipper (probably one of the Wood Maxx chippers) and I got to thinking about the PTO HP of my Deere 2320. On a lot of the TractorData.com pages, there...

I'm building a custom plow for my 2320. I have the quick-tach hitch that I will fab a bracket on the plow to mount on the hitch. I need to know how high on the plow the bracket I fab will need to...

I'm building a custom plow for my 2320. I have the quick-tach hitch that I will fab a bracket on the plow to mount on the hitch. I need to know how high on the plow the bracket I fab will need...

Hi everybody. I found a front quick hitch and plow on craigslist. The owner can't find any model numbers on the quick hitch. He bought it for a 455 and said it doesn't fit. The only info he was...

Couple questions. 1. Does anyone else leave the quick hitch mounting "box" on the tractor during loader use? Or mmm mowing? 2. Do I have to remove my quick hitch mounting "box" to mount my front...

John Deere 2320 .....300hrs But had a battery go bad awhile back. After that ....the gremlins came out!!! The tractor doesn't keep battery charged and the glow plug light stays on. Now I have...

The front u-joint on my 2320 main drive shaft is failing, and needs replaced. Has anyone done this before or can give helpful hints on how to dissemble and replace the u-joint? I can see it with a...

My next maintenance task on my 2320 is to change the coolant. Looking at it I can't see a radiator drain plug or petcock. Looks like I just have to pull the lower radiator hose. Am I overlooking a...

Anyone have suggestions? Everything I find is for a skid steer and I don't have tools to make one. Pics wound be great

I don't have a service manual and local JD dealer has no idea when they can fit tractor in shop for repairs. When cutting grass with belly mower , the PTO select lever pops out of detent whenever...

Hey guys, new to the forum. I purchased a used 2320 with 700 hours on it last fall. To say the least I got screwed. While tilling in the fall the rear pto stopped working...after opening it up...

This past Sunday, after mowing the lawn for 3.5 hours, letting the tractor cool while I did some trimming, I blew the grass and dust off. When I tried to start the tractor to put it in the barn...

I have a 2010 John Deere 2320 with a Onramp 54" mid mount mower. I am having problems adjusting the height of the mower. The max cutting height is 3 1/2" when the mower is all the way up in the...

Can my compact tractor pull a 14" two bottom plow through very loose soil?

Hi all, just picked up a new to me single bottom plow and was plowing up my garden spot when I heard some popping noises coming from the front left wheel when going backwards. Took a look at the...

HELLO ALL i have a 2011 jd 2320 175 hrs on it i noticed a small coolant leak under the fan, hard to tell were it is coming from,mite be from a allen head cap screw i tried to tighten it but it was...

Help! Just changed the fluid & filters - according to the manual it said it holds 3.9 gallons - first I couldn't see it in the window, and now it looks over full??? Any ideas? Should I drain...

HI All,, I need some help with understanding my tractors transmission needs this winter. When cold, 20s or teens my sight window shows no fluid at all. If I operate it for a while it returns...

Hi all and Happy Thanksgiving, Has anyone had a problem with the 3 pt hitch on a JD2320 . Mine won't go down. Worked a week ago when I dropped off an attachment! The lever won't even move! I...

Is there an "easy" way of replacing the RPM cable on a 2023? Me hands seem to fat to fit in behind the fan to get to the cable end. Thanks for any info/help, WiskeyJaR

My newer 2320 (only 275 hours) developed a huge antifreeze leak, my big mistake. Engine overheated while I was mowing some tall grass with the 62D belly deck for about 20 minutes. Radiator...

My battery has failed after 4 years, so time for a new battery. The JD battery is 600 CA, side flange mount with vent tube - 22NF group. All the local auto stores and Tractor Supply have the 22NF...

I've had requests for pics of my home made cab.I pretty much used these idea's for my cab. It was on my 2320. When I purchased the 2720 I installed the cab on it. Front mounts had to be reworked...

Hello all. I am brand new to the forum, and this is my first post. I bought a used JD 2320 2 years ago at about 225 hours from a JD dealer, with bucket and 62D belly mower. Tractor now has 357...

I don't think I have posted here much; if at all; but, I wanted to put this up as my way of saying thanks to everyone for all the info you have posted here on the forums. The ideas for the...

I can get both of these for about the same price. I have a 10 acre horse property and would use the tractor for pasture mowing, manure spreading and moving stuff around. Both should meet my...

Hi all-I purchased my 2320 in April 2010. At 195 hours last week I just did oil, transmission/hydro fluid, all filters and full lube on machine, bucket and 62" Mower. Mowed my lawn once-2 hrs and...

Hello Dealer is selling this combo for $16000 which includes 7% sales tax. I drove it around the lot and every thing seems to be working. Is this a good(reasonable) price? Thanks

Hello and thanks, I am not only a new forum member but also a new tractor owner. Since moving to this amazing piece of property here on the Tennessee River, my wife and I have labored to improve...

i have found a Danuser 18P chipper for about $2k, but can find very little info about it. seems to be set up for a cat-0 3pt and has the shortest PTO shaft i have seen, barely 2ft colapsed. I...

The best add on was the easiest. I found an old drill and stole the handle off it. It really helps when getting up from the seat to get off. This is the best mod by far and easiest. Now I just...

Good Day, Would like to adjust the brakes on my 2320. Where and how do I do this? anyone have details? any pics? procedure? Thanks in advance...

Hello and good day to all. I joined because I just purchased a JD 2320 with a 54D deck, 200cx loader and quick hitch on the rear. It only has 117 hours but was kept outdoors. The PO hit something...

Good day , hoping you all with your vast knowledge can help me with sourcing some items... looking for a thumb for my 46 back hoe... looking for cheap place online to ordwer parts for my tractor...

I am currently looking to purchase a 2007, JD 2320 with a 200CX FEL and a 64D MMM. It has 418hrs on it. It is in excellent shape with manuals, service records and extra blades. It's owned by an...

I just bought a new to me (front mount)47 snow blower with quick hitch. How do I mount the "box" part of the quick hitch to the tractor frame. Obviously I'm missing a mounting kit. Part number...

Noticed this oil leaking down on left front rim. The pic is the inside part or rim. It apears to be clean motor oil from what I can tell. Anyone have any ideas on what is causing this? I noticed...

i have a 2320 and am preparing for the storm that we are going to be getting in the north east tomorrow. I have a 200cx loader and jd backhoe attachment. I was planning to remove the backhoe...

Just Curious, I have been doing some looking at the specs of the 2320 and have noticed that JD list the engine at 24.1 HP. When you look at the Yanmar site for details on the 3tnv76, it lists...

Has or does anyone hear a slight ticking sound in their Yanmar diesel engine. Almost like a valve lifter noise. I always wear hearing protection when running the tractor. Recently I have been...

Re: JD 2320 Idle For those 2320 owners out there, when you pull the throttle back to the idle position, what RPM does your machine idle at? Cheers,

I would say the hard part of the fabrication work is over. Lots of little details left to do. I have the cylinder mounted and the rest of the work is cross supports, gussets, cylinder guard...

I have been looking at the possibility of going green with a 2320 for my property and have 2 different JD dealers selling me a 2320 package with one having a 54" Frontier Rear Blower and the other...

Re: John Deere 2320 Hydrostatic Tractor w/loader and backhoe. After being run for 15-20 minutes, the tractor will no longer go up a moderate slope in 2 wheel drive in either Lo or Hi range. (It...

Re: John Deere 2320 Hydrostatic Tractor w/loader and backhoe. After being run for 15-20 minutes, the tractor will no longer go up a moderate slope in 2 wheel drive in either Lo or Hi range. (It...

Hello to all, I'm new here and am sure glad this forum exists. I own a 2008 JD 2320 and have had no problems with this machine untill yesterday. I was mowing and the engine quit. My fuel gage...

Found this site by researching the JD 2320 I just bought. This is the first tractor I have bought that wasn't a project.

Some features of the JD 2320 sold me over the Kubota model in the same catagory/ price range, JD is truely lacking a snow blade that meets my standers for a tractor with this power and size...

I bought this product on ebay, just search Renew Blak if ya interested. (I orderd the Blak and the Satn from seller. he sent me the Satn and Glos, I emailed him and he quickly sent out the...

I have a 4 yr. old 2320 with 120hours on it. I've owned it since it was new and have never had a major problem with it until now. This morning I fired her up for the first time in 2 weeks. I was...

I recently made some wheel spacers for my JD 2320. The front spacers were needed for tire chain clearance. 1" aluminum with pass thru holes for the lug bolts gives good clearance for the chains...

I recently traded in a 4100 for a 2320. My mid pto shaft to the front quick hitch is two short. Does any know the correct length from end to end. I was going to have lengthened and add a cv joint...

Just received my independent mower lift kit for my John Deere 2320, but the installation instructions were missing from the box. I have an idea as to where it goes, but looking to see if anyone...

looking to buy a rear bagger for my 2320.... if you are selling one, please let me know- saleenlimited@yahoo.com thanks!

I have JD 2320. I was woundering if I can move round bales with it. I was looking at a bale spear for the tph. It would be on a small scale, enough to feed a couple of head. Next option would be...

What's the right Engine oil for this tractor? It's a 2011 with 58 hous on it and of course it is a diesel. Thanks.

I'm looking to pick up a JD 2320 and have a couple questions. Here's what I'm looking to pick up: 2320, 200cx FEL, 54D MMM, R3 Turf tires. First, my thought process and needs are as follows...

I am looking for a mid mount (belly) mower for my JD2320. I would prefer the 62D but would also consider the 54D. I am in the Houston, TX area. Thanks

JD 2320 floorboard and accessories removal to access power shaft front u-joint zerk

Hi All, My JD2320 has a park brake indicator (idiot light - named after me), that seems to hide behind the steering wheel, at least when I need to see it. To make matters worse, the brake does...

hey, my 2320 has a hitch set up for a model 46 backhoe, this changes the set up for my other attachments. since i do not have one solid pin going thru with the turnbuckles. can someone show me an...

Have a JD 2320 with 200cx loader, need to move some ledge stone and logs. Frontier has pf10 clamp on forks, but saw pfl20 forks that appear could be used in place of bucket/clamp ons- forks with...

Have JD 2320 with 200cx FEL, but need to move some ledgestone and logs. Any experience with clamp on forks (frontier PF10) vs frontier PFL 20 or something in lieu of the bucket? sounds like the...

Here's the scoop. My dad is looking for a new tractor. This is most likely going to be the last one he buys. So he wants to get something special, even a bit overkill. The primary function is...

I got my New tractor today!!! Man was I susprised!!! I didnt think I didnt think i would get it till the first of next week. Dealer didnt have the hood guard in stock but he said I could come and...

Well I did it. I bought a new tractor today. Dealer is going to call me when its ready to be picked up. I bought a 2012 2320, 200cx loader, hood gard, 62D drive over deck. Should be ready on...

Hello! I have a JD 2320, and I am shopping for a rear finish mower. I already have a rotary cutter (Frontier 2048). I found a used Land Pride FDR1648 on criagslist for $500 OBO (so I could pick...

I have a Kubota 2360 and looked at John Deere 2320 really liked John Deere for many reasons ground clearance and better 3 point hitch that would better suit my needs over what i have. I would...

Hi, Is $11,500 a reasonable price for a 2008 JD 2320 with FEL and 80 hours? This is a private sale in Maine. Thanks, Jason

I need to replace the block heater on my 2320. Is there a way of not draining all the antifreeze or am I SOL? :confused:

What is a really good price that I should try to get a new 2320 with 200cx FEL and 54Dmmm for? I would be buying it in either Georgia or Alabama, and would be financing it through the 0% 48 month...

Hey Everybody, I'm thinking about purchasing a used 2008 JD 2320 with a 200cx loader. My only question is if this loader has the quick attach/detach capability? Is there anything I should be...

My 2320 is losing power under load dropping to a low rpm that would fluxuate between 1500-2500. If i would stop the mower it would recover but would act up again when i begin to drive. If i would...

I am fairly new owner of a JD2320. I have done some modifications (rear spacers) recently to put chains on the rear wheels for the upcoming plow season. I only have 24hrs on the machine and so...

Is there anything left hanging down after the deck is removed?? I'm looking hard at this tractor and trying to decide on a MMM or finishing mower. Thanks

After looking all over Internet for good pricing for R4 tires an rims to fit my 2320, I talked to a very helpful JD Dealer in Vermont. This guy named Scotty I believe explained to me what I was...

Hi All. This is a first post after some weeks of reading good stuff here. I must say I am impressed with the quality of exchanges in this forum. I just completed the financing of a new 2320...

fellow members i have a jd2320 with power beyond that i want to attach a woods tgs50 to but the dealer says that i will need a special valve to do this and want 1700.00 for it. what will i need to...

Does anyone know where I can find front and rear rims to fit my 2320 compact tractor other than John Deere dealer, their price is unGodly. Looking for an extra set for AG tires.

In response to Deere 2520's post last week regarding installation of a rocker switch for an electric actuator, I thought I would finally post how I handled this task. I completed this task in...

Hello all, My big little tractor arrived yesterday, right now she's hanging out in the garage with the car until the barn gets built. We've got two acres to work with here in NC and I think she'll...

Tractor running fine. After approx 2 hours i shut off and got no crank on restart. No lights either . .just a weak whine behind the instrument panel. Thought maybe alternator died and somehow...

I was just operating a 2320 yesterday. The machine ran great however when starting, it jars the whole machine once it starts and then it stops once at idle. This isn't a very big concern however...

2320 starts fine but is running off the battery. Alternator output voltage is correct at low and high idle. Battery ground connection is clean and tight. Battery voltage is 12.8 running or not...

Just got a PTO Chipper for my JD 2320. Problem is, I can't keep the tractor running with the PTO on unless my rear is in the seat. I'm tired of putting a 100lb sack of feed on the seat to chip all...

I am considering buying a used 2010 2320. How much should i expect to pay for this tractor? Also, What are the differences between the 2010 and 2011 models? Thanks!

Hi, I am trying to get a new 2320 within the next couple of days. I want to also get a front end loader and 62 inch belly mower. My dealer is saying the best he can do with a 18% discount from the...

What size box blade to get for a JD2320 4' or 5' ? Found a good deal on a 5' Woods box blade but wondering if thats to big for the JD2320.

I was washing the tractor down with the garden hose when I realized what looks like a rubber coating on the cooling line in front of the radiator and also just below where the battery sits has...

I was washing the tractor down with the garden hose when I realized what looks like a rubber coating on the cooling line in front of the radiator and also just below where the battery sits has...

Hi all! Looking at a JD 2320 (might buy tomorrow) with a 200cx fel and a 54" drive over mower deck. Dealer is adding filled tires and a ballast box. Best cash price I have got was $15,964 +...

Finally took the plunge and got a 2320. Looked at Kubota, but after driving 2320 and 2520, I much prefered the Deere for quiet smooth operation. Did some shopping in So. NH and No. MA and got...

Hi, We had a late season snowstorm, and i wanted to reattach my front mount blower. However, I am finding it very difficult to reattach the front PTO inside the quick hitch mount. It was also very...

Will be getting a JD2320 with FEL and ballast box shortly. I'm estimating it will be around 3000 lbs total. Wondering if it's a bad idea to store it in my shed (8' x 16'). Floor is framed with...

Mowed the yard, moved a fallen tree to the burn pile, graded a low spot and dug a hole. Oops! Time to pick up the kiddo from grandmas.

I just bought some mirrors from Curtis Cab, and want to mount them on my JD 2320 tractor, which has a curtis soft sided cab.I am wondering how to mount these to the tractor cab, so that in the...

does 16,000 sound like a good price with 200cx loader and 54d mmm with independent lift?

Price with 54 inch mower deck, 200cx few, and frontier box blade for $18,325. Seems good? 0% 48 months.

Hi, I'm going to buy a new compact. My first choice is a JD 2320 with FEL, MMM and snow bl. But in Europe this one is far to expensive. I think I'll pay appox 22000 US$ for this one in US, but in...

I am looking at my first and only real tractor for my house. I have 5 acres. Will be mowing, tilling, snowblowing and maintaining lane mostly. i need some advise on what the better tractor for my...

Hello All, Wanted to say thanks to all who helped me make the decision, looking forward to getting to work or playing around not sure which.

I went shopping for a new tractor. I like the size and looks of the 2520, priced a new 2011 it with 200CX FEL and JD46 Backhoe at $23,500 ($6700 for backhoe WOW!) Anyway dealer called me and he...

With thanks to Kennyd's post and links provided here to posts from lt220, jimgerken and lincolnvt (thanks all for sharing your knowledge)...

Thinking about buying a JD 2320 or 2520. Leaning toward 2520 for an additional 2 Grand +/-. Will mow about 4 acres and raise large garden. Your thought on weakness or advantage on both Please.

The John Deere power beyond kit for my tractor lists for $304 CDN. Looking at the kit and reading and gathering knowledge from the expert members here I think one can build their own PB kit at...

For any 2320 owners out there. I received pricing from a local dealer. Any input if pricing listed below sounds too high or not? I haven't tried haggling with them yet. They listed options on the...

Hi all hydraulic experts. I've searched and not found a direct match to my idea to split the SCV hard lines. My thought is to remove/somehow use/replumb the factory JD 2320 SCV hard lines through...

Here are a few pics of the Heavy Hitch my CFO had delivered as a late Christmas gift:

Just a price check on a jd 2320 with a 62" mmm, BH, and a BH. I live in upstate ny about 20 miles from binghamton. Also can the 2320 run full size implements like a brush hog or post hole auger or...

I am debating between the kubota bx 25 and the jd 2320. The kabota is nice because it comes with a FEL and BH for a good price. The only thing holding me back is the ground clearance and that the...

My new 2320 with FEL- and advice about type, size and methodology of trailering and transporting?

New to the forum- my new 2320 is coming next Monday...feel like an excited kid who can't wait to play with his new toy!

Well, I mentioned in another thread that I'd outline the reasons why I traded my B2920 Kubota in for a Deere 2320. And at the risk of criticism, I'm writing this up to save someone in my position...

Here are a few shots of my 2320. I've got 9 hrs on it so far. Just finished blowing snow in Winnipeg, Manitoba. A beautiful sunny cold day at -21 Celcius.

I am in the process of picking out a new tractor either the 2320 or the 2520, I am trying to sell my 2008 Cub Cadet GT 2544 on craigslist but have had no bites yet.... I hate to loose that extra...

My 2320 is in the locked differential mode and won't release. That is the lever is down and won't rise to indicate unlocked. This is making it difficult to steer while plowing. Any ideas?

I found last winter while doing snow removal with my 2320 that the battery would get very cold and I would often have problems restarting the machine without jump starting it when going back out...

Does anyone know if making a wider wheel base on a JD2320 is possible ? I have many steep hills and need more stability. Any manufacturer/kit recommendations would be appreciated.

So, A guy (named Joe) from this forum asked me to build a custom plow setup for his new 2320. As some of you know the 54" plow that JD offers for the 2x20 series machines is a joke on many...

It's a really nice day so I figured I'd try to mount the 62" mower under my new 2320. I quickly realized I do not have the front bracket to mount the mower. The salesman told me all the stuff I...

Just curious if there is any available rubber floor mat for a 2 series JD. My plastic "floor" is very slippery. Maybe it's the particular shoes I wear too but thought I'd ask.

Hey guys, I read nearly everyday topics listed here and enjoy it alot. I'm new to the site and hopefully someone here can assist me with a problem. I have a JD 2320 and I'm installing a 2 spool...

I am thinking about adding hydraulic rotation and deflection to my snow blower for this winter. JD has the 3rd scv kit available now, but since I want to add both I need 2 sets of ports. I know...

Hi gang, First time poster here. I am a Lawn Care Professional and am strongly thinking of ordering a 2320 mostly to drag a Ryan 48" Lawnaire Core Aerator around my customers lawns. At some...

I'm having some problems trying to figure out how to mount chains on the rear wheels of my John Deere 2320 tractor. First of all, to clarify why I even think of chains, I live on the side of a...

I have a John Deere 2320 with about 220 hours on it. About 20 hours ago the hydro fluid started getting milky and not pumping correctly so I changed the filter and replaced the fluid. Everything...

I was at the dealer earlier this week picking up some supplies when I happened so see a 47" snowblower sitting next to the new ones still in the crate. When I inquired, the salesman informed me...

I was sold on green and yellow paint, but everyone I speak with tells me I should get something orange - mainly a Kubota that is orange. See - the people that are telling me this seem to know...

I'm thinking about buying a new 2320 with a 62" mower, a snowblower, and a tiller. I called the local JD dealer today and told him what I wanted and he told me they have a slightly used 2320 with...

Hi, I have 10.5 mostly flat acres of property - with about 6.5 acres being forested. The rest is about and acre of cleared land for building (barn, house, vehicle turnaround etc.) and then there...

I ordered the 2320, 200cx FEL , and the 54D but from what I read here its (54D) tight to edge with and some are advising to go with the 62D because it sticks out farther to get in tight around...

For any tractor salesman or other experts out there, can you toss out a ballapark figure on a 2007 JD 2320, 120 hours, FEL and Land Pride 48" mower? I'm looking to get a bigger tractor and I need...

I've been comparing a Kubota B2320 to a John Deere 2320. I felt this was a fair model match up. Here are some of the key differences I found: Kubota B2320 - LA304 loader has a pinned non quick...

I had one JD dealer spec a Woods BH70x for a 2320/2520. Another told me it would be too big, he recommended the JD backhoe. Anyone with any experience with this combo?

They delivered the tractor today. Yippee! I may have to call in sick tomorrow. Teaser pics, click link below for the rest.. Tractor Stuff

I have be thinking about purchasing a dump trailer for awhile now. I'm in the middle of a project where it would be really nice to have one. I have found a good deal on a 6X12, but I am...

Funny how it came about, really. Had my mind set on a used tractor and FEL. I'm really cheap. The 0% financing offers from all the manufacturers had gotten my attention though. I had actually...

Got a favor to ask if someone in the Denver Colorado area has a Deere 2320, 2520, or 2720 tractor. Drop me a PM or Email please. Chad

I think I found a great deal but this is my first tractor. I was pondering between a brand new JD 2305 and JD 2320, then not a mile from my house a guy is selling a 2007 BX24 loader-backhoe, 60...

Hi all-looking at purchasing a JD 2320 with FEL and 62"mmm. The snow plow available from JD is a 54" front-mounted bade that many TBN'er's say is not wide enough when the blade is angled-the blade...

I am new to this but have viewed this site and found it very helpful with the information in concern of my future purchase it even swayed me from the 2305 to look at the 2320, I shopped at other...

Hi all, Have been lurking for awhile. I have been to all the local dealers and have decided it is between these two. I will have a FEL and RMSB to start. Eventually I will want a roto tiller. Any...

I've finally decided on the 2320 over the 2520 (this site is great and full of great reviews BTW). Now I need to decide on the options/add-ons and would like some feed back. Here are the...

Will a 2320 handle a 72" finishing mower or would I be better off getting a 60"

I really need to put a small bend in the 4WD lever on my 2320. The way it is now is driving me nuts and more so in the winter with a big set of gloves on. I will need to heat the lever and would...

First time on TBN, I just sold my BX2200 with FEL and mowing deck looking to get a little bit longer and wider tractor for stability and of course some more power wouldn't hurt either. I landed on...

I am in the process of building a backhoe for my 2320. I would like to build the subframe as well and attach it to the tractor the same way as the JD subframe designed for the 46 BH on a 2320...

Hi All, I noticed in the Fall that I had some red drippings coming from the 4 hydraulic quick-connects (not sure which one, or if more than one). The FEL was connected. Not huge puddles...

Finally got the ok from the wife to get a real tractor. Torn between B2620 vs. the JD2320. Tractor will be primarily used for mowing about 3 acres of lawn. Looking at the 60" MMM. FEL work will...

Finally got the ok from the wife to get a real tractor. Torn between B2620 vs. the JD2320. Tractor will be primarily used for mowing about 3 acres of lawn. Looking at the 60" MMM. FEL work will...

Does this seem right? My manual says the 2320 weighs 1,660 lbs. If you want to tow a trailer with brakes it can tow 4.5 times it痴 weight 7,470 lbs. Trailer with no brakes 1.5 times it痴 weight...

Hi All, thanks for great forum. I am looking to purchase a used 2006 JD 2320, with a 200CX loader. Time is higher , at 550hrs. best price I can get dealer to is $9400 Is this a reasonable price ...

I just visited my local John Deere dealer, and wanted to buy a quart of oil for my 2320, After checking the level I found that it was down a little bit. It probably was never quite full when I...

Hi guys, well snow has finally come to northern maine, and I just took out my tractor and front mount 47" snowblower for the first time. I used to own a x485 with this same snowblower setup and it...

Racing against the boss with my 2320...

Hello all -- I will start shopping for a new CUT in the next few weeks, armed with the knowledge I've gained by browsing this forum for some time. Thanks for the resource!:D I think I have a...

Hey guys I found this seller on ebay. it might not be pretty but it would keep you out of the blowing wind in the dead of january. I might pick one up because it's not too expensive and i don't...

I'm new to this and looking to purchase a nice CUT. I have about 3 rolling acres to mow with various landscaping, and snow plowing. I've got my choices down to a John Deere 2320 and Kubota 2320...

I'm looking at CUTs and this one caught my eye in MI. Drove it today, really liked the way it handled, controls, etc. I'm new to this but liked the machine. Anyway, here's the deal: a 2007 model...

I am looking to buy a brush hog for my John Deere 2320, I was wondering how well the tractor handles a 4 foot rotary cutter, but I was also wondering if anyone has used a 5 footer behind a 2320...

OK, so after the past winter using my 2320 with a rear mounted Farm King snowblower, it became very obvious that I needed a cab! When that ol' wind catches the stream just the wrong way and hits...

Recently brought the JD 2320 TLB from my family "camp" to my home. I borrowed a buddies 20 foot 12K trailer, a little overkill I know, but what can you do. Of course after spending a couple...

New 2320 being delivered tomorrow and I'd like to get a 3ph log splitter in the next few weeks. Does anyone have experience with the Northern Tool 3ph Splitter powered by the tractor's...

All, I'm looking at both the JD 2320 and 2520, trying to decide if I spend more for the 2520? I have quote for both with FEL (slightly bigger bucket with 2520) and both with 62D ramp MMM...

Hi. I'm new to the forum and tractors as well. I have a big dilemma. I have a 125 acre hobby farm in north central missouri made up of about 50% woods/ 50% open fields. 25 acres are in row...

On a JD 2320 after you change the transmission / hydraulic fluid, filter, clean the internal filter and magnets. Once you fill the system do you have to bleed the system in anyway? Thanks

On a JD 2320 can you leave the loader on and drive on and off the 62 mmm deck with out breaking it? Or should you take the loader off?:D

Is this a deal or not? $13,750 for a spanking new 2320 with cx200 loader and weight box + R4 industrial tires?

I've been tractor shopping for a few weeks and have narrowed my choices to the two Deeres and the old style Kubota. I can buy the 2520 and the B7800 comparably equipped with FEL and 60" MMM for...

Hi, Could someone please give me the length of the JD 2320 with 200CX loader to the back of the 3PT arms. Also the length of JD 2320 with a 60" box blade attached. Thanks, Mario

Installed the fender extensions today, and when I was looking for threads on them here I couldn't find any so I thought I'd post some pics for future searches.

http://i182.photobucket.com/albums/x247/kvjohndeere/100_0892.jpg http://i182.photobucket.com/albums/x247/kvjohndeere/100_0896.jpg

Here's a few pics of the new 2320. I'm lovin' it so far... I'm actually looking forward to doing some work around the yard this summer!

We finally got our 2320 Thanksgiving weekend and immediately got it covered in mud doing various pre winter chores. YAH! I moved the skid shoes on the blower all the way up as I only blow snow on...

WHY DOES MY JOHN DEERE 2320 BONCE WHEN IN HI GEAR ? IT IS BRAND NEW WITH ONLY 5.6 HOURS AND HAS A 54 INCH ON RAMP DECK :confused: :confused: :confused:

Took delivery on a new 2320 last Friday. The info in many discussion threads was invaluable as I tried to decide between the 2305, 2320, and Kubota 7610 Main reasons I went with 2320 were ground...

I am looking at purchasing a compact utility tractor. Have looked at the JD2320 and the New Holland TC30 - price comparison is about $1000 difference between the two. The NH TC30 is manual...

Howdy everyone. My wife and I just bought a new 2320 w/ 200cx FEL and 62d MMM last week. With much help from the posts we read here we feel we bought the right tractor. So, I wanted to share a...

These 2 tractors are almost the exact price. The B7800 has more hp 30/22 vs the john Deere 24/18. The John Deere has position control vs 1/4 inching on Kubota. Would there be much noticable...

I have been looking at the JD 790's on the Deere website. It has a footprint the same as my current tractor and 27 HP vs. 19. However, I went to the JD dealer today and saw them, a 790 and a 2320...

On a previous thread, you guys advised me to 'float' the 3ph by moving the rockshaft control lever full forwards. I haven't tested that because I now have my BH on and I'm reluctant to take it...

I'm doing a first time, by myself, hookup of the BH and I don't want hydraulic fluid squirting out when I disconnect that line. Along the same line, after I shut down I understand that I should...

I'm asking for it here because the minimum RW rake is 6 feet and the RS is 5 feet. I'm not sure if a six footer may be overly big for the 2320. Other considerations the RS + wheels + blade +...

When I first started looking at tractors about 2 months ago the JD website showed all the 2000 series tractors it currently does as well as the 2210. I knew the 2210 was an older model and after...

I had almost given up on purchasing a John Deere this time around and had my mind made up to go with a B7610 but then a Local dealer started to compete and we are now at $14800. for Kubota and...

Nevermind...I see that there is already an excellent discussion on this topic. My bad.

I read here awhile back that if you put a backhoe on a 2520 you have to remove the subframe to use a MMM but on the 2320 you can leave the subframe on. That was awhile ago and wondering if it has...

I am early in my search yet, but if I had to buy today I would either buy a JD2320 or a Massey 1528. I know I am not exactly comparing apples to apples, but I think either would meet my needs...

Is this a fair deal ? JD2305 to a JD2320 2 month old JD2305, 30 hours on it, 200cx loader 53” bucket, ballast box, 62” mmm, lx4 rotary cutter. Paid $14,325 for the package. I put down $2,895...

I have a JD 2320 that I just got (loving every minute of it:D ) and now realize that I am going to need the rotary cutter a little sooner than expected. With the latest rains the fields are...

I listed this on eBay and I was wondering if this looks like a fair price? "NEW JOHN DEERE GRASS CATCHER - 2210 2305 2320 2520 4115 PART #'s 1402GX & BM21495 MATERIAL COLLECTION SYSTEM" Ebay...

I called my dealer today, and told him to put a 2320 in the mail for me.. While I was at one of the dealers, I sat on one and noticed the Hydro Pedals are higher than I would like (I'm 6'3".)...

Okay...so my fiance and I moved to Upstate NY from Hawaii (no jokes) and we purchased 40 acres up here. We are building a house and we needed a tractor so we decided on the 2320 with 200CX FEL...

Since posting this, I have decided to look into the JD 2520, not the 2320. Does anyone know how the NH TC24D and the JD 2520 compare? The NH was a 2003 with a 12LA loader and a 756 hoe. A tree...

I was wondering what the JD 2320 is compaired to, a Kubota BX or B? I am guessing the B series and the JD 2305 is compared to a BX?

The new 2320 came last night. Could just about photo it. 10 minutes later it was in the mud cleaning up around the barn after all the rainfall we've had lately.

Hello all, I've been monitoring this site for awhile and now can finally post. I'm waiting for my 2320 (R4 tires) to come. Ordered on the 16th. Here are my attachments: FEL (200CX) BH (13”...

Hello all, Just thought I would post some pictures of my toys. I have never posted anything here before so I hope it works. Flickr: Photos from aesanders71 I just added a bumper hitch to the...

I wanted to thank you guys for your help. I just ordered a new 2320. Here’s the breakdown 2320 $11,800 200cx Loader $2400 62D mowing deck $2375 Loaded tires $240...

A shot of my new 2320, FEL w/ 61" bucket and 62" MMM. :D