Not really a comparison thread. But I now own both these machines. Just picked up a '17 3550 with R4's, cab, loader, 4wd ~600hrs Some may remember my quest a few years ago saying I wished a mfg...

Hi I'm going to look at a Kubota MX5100 geared, loader, it has a small leak from rear PTO, roughly 5500 hrs. Is there anything I need to look for, sounds, etc besides the normal, clutch, engine...

I'd like to put a loader on my MX5100. The dealer said he can get the loader but not the front setup so I can have the SSQA on the loader. I can get the loader but it has to be a pin-on bucket and...

Did kubota make an MX5100 with a cab? I haven't come across any in my searches.... Thanks!

So....I've had a 3-14 plow for several years. Never had an issue with pulling it with the MX. But being a smaller, older, Ferguson plow, and no trash/cover boards, or even a good way to attach...

I’m not sure if this is a problem or not.. But my hst L2501, the pto shaft turns when tractor is shut off. The MX doesn’t. It makes 1/2 a revolution or so, and then stops…. It doesn’t matter if...

Bought new 5 years ago, 215 hours logged. Filters and maintenance performed as required. Now it has a failure with the fuel injection pump. Dealer wants $2400 to repair it. Is there a place...

Don’t know the name of the part. Looking for a detailed drawing for hydrolics of Kabota MX5100.

I need to find the electrical wire for a 12V connection on an MX5100 or M7040. I know there's one under the fender on the M7040 but used those for work lights. Not sure on the MX. I'm hoping...

Looking for advise on how to install the Land Pride 380-166A 3rd function valve kit on my MX5100 with a backhoe. The directions are very confusing that comes with the kit. Trying to find out...

Everything You Need to Know About a Kubota MX51 - YouTube

Hello, first post and looking for my first tractor. Have 22 acres. 2/3 wooded and 1/3 open. Lots of trees and hilly. I've got a 60" zero turn for the finish cutting, but want a bush hog for...

So like many, I am getting tired of getting cold and wet when blowing my drive. I have a 2011 MX5100 that I love and it痴 my second Kubota. I just received a quote for a hard cab for $4k FOB US...

Bought this tractor yesterday and it's a significant size upgrade from my previous tractor. St some point in time I will buy a larger Bush hog. How large a cutter would this tractor operate?

All of the sudden my 5100 is overheating every time I mow with my 6 House rotary mower

Can anyone tell me what size the tire lugs (front and rear) are on a 2012 MX5100 series tractor?

thinking about getting a suspension seat for my tractor, anyone have one or something similar on their kubota tractor?

looking for a Hydraulic top link for my Kubota MX5100 that will be used for rear blade, box blade and landscape rake. I'm not sure what size would best fit my tractor. Thanks , D

Anyone have any experience with this tractor. Looking for an utility tractor, with loader for yard clean up, fence posts, some light farm work like a manure spreader. Don’t think it would be...

Recently got my new MX5100HD-AU, only 15 hours up, mostly chipping pruned ornamental branches with the Woodland Mills WC88. Very happy so far with the MX and the chipper. My other main use will be...

Also, I found a part that's leaking fuel. Not sure if the problem and the leak is related. I'm not sure what part this is. Any thoughts on the running rough / not staying running problem? Has...

I want to work on some hog damage in our lower pasture (around 5 acres) as well as disc some mounds in a couple other fields to break up the dirt to scoop up with my FEL to use to set several...

Anyone ever found an aftermarket source for the inner tie rod boots? Probably the same as several other kubota models but its on a MX5100 OEM # is 35080-44680 In the ~1-1/2 years I have had the...

Looking at getting a little bigger tractor. With DPF and other emissions, I don't want new. Looking at a used MX5100, any pros/cons to this model ? I haven't gone to look at it yet. Dealer is...

Tractor is a 4wd, hst with 275 hrs. 2 hydraulics on the back and skid steer type disconnects on the bucket Has the LA844 bucket and comes with a bush hog sq720. Firm price at 23,000. Tractor looks...

Does anyone know if anyone makes an oversized radiator for a mx5100HST? I pull a landpride batwing and although the tractor does not overheat, when I stop and cut the machine off it will boil out...

I'm looking to add 2 rear remotes and T-N-T to a MX5100 HST that already has FEL and true 3rd function. I was wondering if you guys could confirm that I have the correct idea of the flow of the...

I have a ten year old M5400 two wheel drive. I am looking at a newish 2013 MX5100DT (49hp) four wheel drive with a front end loader. My question is simple. Do yall think that the newer smaller...

Need the assistance of the TBN brain trust. Got a weeping hose on my mx5100. Weeping several places through the hose. The hose ends are labeled SF-PF-04-14. Googling seems to lead me to...

So yesterday, I took delivery of my new (to me) MX5100 with loader. I had the dealer I bought it from add a third function valve and two rear remotes. After playing with the tractor a bit, I...

Hi I have the choice between a kioti rx 6010 with 4and 1 bucket and cab 2 years old excellent condition 500 hrs 30,000 Or Kubota mx 5100 4 and 1 bucket And slasher New 40,000 Go...... First...

Got my new-to-me disc. Overall not too bad. The bearings need replaced in one rear gang thats locked up. But the MX pulled it with no issues at all, both up and down hill in the corn field, then...

Hello, I have been looking for a tractor to do general chores (brush removal, 3/4 mile gravel drive maintenance, log moving, etc) around our wooded, rocky and hilly 250 acre property for some...

I've got 62 hours on my MX5100 now. Two days ago when I parked it, my float function on the FEL worked properly. I push it all of the way forward, it drops down to the ground, and then I release...

We're building a house on 50+ acres so I felt I needed a tractor for around the house for mowing, maintaining a gravel drive, and fighting the ever invasive Yaupon. I was thinking about 30-40 hp...

Does anyone know if the MX 5100 wheels/tires might fit on a a L4150. I found the whole set for sale "AG tires" for $1400. Only have 257 hrs on them. Was just wondering seems to me that the tires...

What is the biggest you guys have ran? I am in need of a disc. Dad always had a disc, and we always used it quite a bit. He actually just had a couple, and always see these little 6-8' discs...

As promised, a new thread detailing the 3 remotes and TNT build. Here are the parts used. For most of the fittings and adapters and hoses, I'll quote DHH or Surplus center prices, allthough I...

After beating my head against the wall for the past week, trying to decide how to do the hydraulics. Stackable valve? monoblock, single valve + selectors, etc etc, I have finally ordered parts...

Pics today of mowing with the new-to-me Woods DS96. Its a nice cutter for sure. And these next pics are of two different lots that I do 3 times a year. Lucky if I can stay on the seat much over...

Started the research today. Still not in a hurry as I don't have any uses at the moment. Dang stuff is expensive. Haven't really found a "kit" that has all that is needed. Rather a valve (l8304...

Got to really test her out today. Havent done much other than pilfer around the house with it since I got it. Had a 6 acre mowing job to do today Real thick grass. Was a retired hay field. So I...

Does anyone know how to tighten up the cruise control on the MX5100, mine won't hold at all. It work for about 1 year now won't hold. Thanks:confused:

My lift arm has slid off the spline at the end that attaches to the tractor. What keeps it in place. I have looked at Messicks diagram but still do not find anything that holds it on.

I have a Kubota MX5100 4x4 gear drive and I would like to add some wheel weights to it. I was thinking around 1k (500lbs to each tire). I have a source to get some 1" plate just slightly above...

Last weekend I did some grease and lube work around the tractor. Greased the front pivot, taking out the relief plug and pumping grease in until it came out the relief and then a little more to...

Good morning all, I'm trying to take advantage of the "Black Friday" special and get my Pats Quick Connect ordered, but am not certain just which one I need. I have an MX5100, which I...

Was out brush cutting, happened to stop for a minute and when I went to continue bota had no power. Only movement is in low gear 1st-3rd and it's basically creeeeping. Fluids all seem fine. Any...

I have an MX5100 HST that has been very reliable. It has developed what seems to be a bearing noise when in mid range or high range. the noise doesnt occur when loaded at lower speeds and not at...

I can get wheel weights quite a bit cheaper at Everything Attachment than I can from a Kubota dealer but I can't find out the bolt requirements for the weights. According to Everything Attachments...

I was wondering if anyone is running a flail mower on a MX5100 (or close to it) and wondering how it does with whatever size you are using. I found an 90" Motts/Alamo flail I am interested in and...

Thought I would post a pic or two of my brush guard. I used the bottom of the factory brush guard and made a new top for it.

I need some help on my MX5100 loader. I built a work platform for use on the forks on my front end loader. I also use the bucket on the loader on a regular basis. My problem is that the hydraulics...

My MX5100 is 3 years old and I have had this problem 3 or 4 times before. It is HST drive and something happens with the forward / reverse pedal and it doesn't make home position which won't...

This one has me baffled. I started my MX5100 this morning without issue. It ran approximately 45 minutes. I hooked up a new-to-me finish mower - without shutting off the tractor - and climbed...

I have an MX5100, tractor is great except the cruise control lever wont hold. I place it where I want to speed to be, it holds for a few minutes then slowly returns to stop position. It starts out...

I've just bought a slightly used MX5100 from a friend. The brush forks were connected to the front loader. My friend told me that the bucket was very hard to hook up, so I expected to have some...

Looking at a MX5100 and a MX5200, both with HST 4wd and loader. I thought the main difference was the tier 4 exhaust stuff and from what I've read and heard I prefer to go with the MX5100...

Paint finally showed up in the mail so I could tackle this project I've been meaning to do it forever now. The paint was way too cold to use from sitting out in the shop. Gonna let this...

Anyone out there installed a circulating engine heater on their tractor? (MX5100HST) Wondering where to install hose port connections for best results. Any info would be appreciated. thanks, in...

Looking to maybe purchase a Wr long 4 in 1 bucket, according to their fitment chart my LA844 loader has an avg lift capacity of 2145 lbs. which means an ultra jaw 2 would be almost too light but a...

Drove through water hit a deep pocket, sucked in some water through breather, tractor shut down . What is proper procedure to restart ? Have not tried to re start it yet . Any advice would be...

I bought the MX5100 the other day and I am want to add some rear remote to the tractor. I would like to have at lease two float valve installed for the TnT setup. Does any one know or have any...

Ammo can tool box, 3 point trailer hitch, bucket hooks, clamp on pallet forks, clamp on trailer hitch. Thanx for looking

This is my first post on your site, thanks for the oppotunity to join in! I own a small acreage, and purchased a new 2012 MX5100HST with loader, backhoe, 72" rough cut, 72" tiller, and 84"...

I have a mx5100 with loaded tires. I read post where people have to have loaded tires, wheel weights and a ballist box in order to keep there tires on the ground when using there FEL. On my...

I've recently purchased a 40 acre block of land that is mostly pasture, but has about 5 acres of bush or woodland. There is a lot of fallen timber in the wooded area and some quite large fallen...

I have an L4300 as well s an MX5100 and use them for seeding and tilling things. Both are rated to lift 2860 lbs at link ends or 2310 lbs at 24 inches back. Usually, I lift 1300 lbs and it's no...

Nope, not looking at which one to buy but just some thoughts. We recently purchased a BX25D to help with small chores around the house and take care of things the MX5100 does not do as well...

Finally had my tractor delivered and it was a little sad to watch them leave with my L3400. First thing was to lift a 5x4 hay roll with no ballast to see difference promised by the dealer. All I...

I am signing papers in the morning for a new 2013 mx5100 gear model with 844 loader. Paying 26,500 with rim gaurd filled rears and bale spear for the front. They are giving me 11k for my 2006...

pushin some snow banks back because of the weather comin... the shoulder of the road was frozen with water running underneath. nothing like 4wd and kubota horsepower.

This is my first tractor. Other than clearing the driveway, I don't know exactly what I'll be using it for yet, but I have plans. FEL's are very useful, I may get a snow blower, I definitely...

Greetings. After several months of lurking , I have finally registered. This week I will be ordering a new MX5100HST. I think I have the options I want all figured out. But let me run it...

So I have been thinking about upgrading to a larger tractor from my MX5100, but not sure how far to go. The 2 main reason I want to increase size is for more lift capacity and the ability to run a...

I own a Kubota MX5100 w/hydrostatic transmission. I suspect I have a "safety switch" problem, because as of yesterday it won't start. Basically, when I turn the key there is no response. The...

All 4x4, all with FEL, and all HST. I have a rough quote of $25k for the L4600 and haven't checked on the MX's yet. Website build price is within $300 for the L4600 and MX5100 and the MX4700 is...

I have a new mx5100, my top link appears to be too short. To get the top link out level with the lower hitch arms it is around 3/4 of the way extended out. And when using my box blade, if I adjust...

Decided to get out and clear the driveway around 3pm today and the tractor would not initially start. It had power and I had used it earlier in the day no troubles. I thought perhaps it was the...

Looking at purchase of MX5100 with a front end lift. From what I have been told really need the 4 wheel drive to fully use front lift. Adds a good bit to price of tractor so wanted to get thoughts...

So far I have logged roughly 5 hrs seat time. Mainly mowing with a six foot rotary cutter and clearing dead cedar trees with the FEL. After spending years operating older machines I can say it is...

As a bonus at work I was told to go buy myself a new tractor. I said OK... But as an engineer I am spending way too much time analyzing the options. Here is roughly what I do with a tractor...

I started my 2012 MX5100 today. It ran fine for the first 45 minutes. I let it idle in the yard for about 15 minutes then went back to pushing snow. made about 100 foot pass under load and the...

I was finally able to get my MX5100HST on a trailer and move it with my own truck. I blew the motor in this same truck about a month and a half ago towing an unloaded trailer (large injectors +...

On this picture, are the holes circled in yellow used for the Kubota frame mounted backhoes? This is at the base of the ROPS on both sides.

Folks, new to the forum, but have been a follower and reader for some time. I have a farming background, mostly john deere 125+ hp tractors. I ended up with a Kubota MX5100 tractor about a year...

Changed fuel filter today on my MX5100, following the steps in the Op Manual for bleeding. But the engine shut down just before I closed the bleed valve and will not restart. Apparently the...

What's the biggest disk my tractor will pull without over-working it? Also, will this tractor pull a 4 row planter? Appreciate any help/advice.

Does anyone have experience using Rotella T in a Kubota MX5100? The manual seems to say that you shouldn't use it because one of the many Rotella T specs is CJ4. The manual, if I'm understanding...

I am the new owner of a mx510 0, 4hrs on odometer. I really enjoy the tractor and am getting used to the controls gradually. I already know about the jerky 3pt hitch thing. I just found another...

Hi all, I'm looking at buying a M6040 or MX5100 and need some width info. The product brochures for both machines state the minimum width, but I need to know the max width to determine if either...

I had heard it both ways before i purchased. It won't lift that. or It'll lift that no sweat. The "that" in question is 2000lbs of heating pellets. I have 5 tons delivered every year and was tired...

Is that a decent price for this tractor

Just did my 50 hour oil change. It seems the MX5100 has 2 oil drains on the bottom of the pan, one on each side. Wonder why come this is??

Mx5100HST OR DK50HST OR 5035 MAHINDRA HST can't make up my mind. I currently have a kubota L3200 HST I need more hp. The mahindra is huge and heavy The kioti seems ok, I like the fact that the...

Im looking to add some rear work lights to the tractor and Im wondering if any of you out there have completed any such mods before. Im havin trouble to find rear power.... any tips.hints or...

Hi guys, new to the forum. Im looking at tractors, I think I have settled on a Kubota MX5100 HST, FEL, R4 tires. Ive had quotes of 26200-25000. Does this sound like a good ball park? Im in Ga...

well folks, i bought my first tractor ever. its a mx5100 hst with grill guard, calcium loaded r4s, LA884 fel and one set of remotes.i bought a landpride 2760 rotary cutter with chains. i...

My MX 5100 (about 200 hours on it) quit after about 30 minutes of bush hogging. The only other time it quit, I cleaned the fuel filter element, bled the fuel system (as described in the...

Bought new four years ago, used it hard in the woods. 200 hours now and it's needing TLC.

Just got my '12 MX5100DT with LA844, QA bucket, grill guard, and Rim Guard. For me, the power and size are perfect. I'm ordering a tooth bar tonight and leaning toward the WR Long "TB." The QA...

LA844, quick detach, grill guard, 1.6hrs, $24,600

DT, LA844, quick detach, grill guard, 1.6hrs, $24,600

Hey guys I'm looking at a new MX5100 HST 4x4 with FEL, R1 tires. A nearby salesman gave me a price of $27150 out the door which includes farm tax of 1.5%, loaded tires, and full tank of fuel. I...

I'd appreciate any tips you guys have on finding replacement wheels and tires (R4 or R1) for an MX5100. I'm looking at one that has turfs on it, and I would want to replace them with R4s or R1s...

I have a Kubota MX 5100 with hydrostatic transmission. When I get off the tractor while the engine is running the engine shuts off as the shuttle ignition shut-off switch senses that the tractor...

Just wanted to see what you guys think.... 2004 Chevy 1500 extended cab Z71 5.3 3.73 gears 40,000 miles No WD hitch, just 2 5/16 ball- Trailer 20 ft 5200lbs axels both with brakes. Tractor- Kubota...

well my sweet mx5100 hst is gone.i traded her for the 7040 HD SU 4x4 ROPS with 1153 loader.shes in the shop getting the 2nd remote put on her.so itll be sometime next week before i get her home.i...

What is the difference between a Kubota MX5100hst and their L5040?

Here's a couple shots of my MX bringing out some Poplar that last years drought killed.

Does anyone know what a 50hr would cost parts/labor?Reside in Ct

I think I am going to buy a mx5100 dt. I want to rig it with a quick attach root grapple. I would appreciate any advice on options that will facilitate rigging and operations. Thanks, Bill

Just got a mx5100 and want to add a grill guard. Haven't checked with dealer yet, there's one on ebay for $249+. Making my own probably not an option. Any other suggestions?

Hey Guys, I'm looking at a used 2011 Kubota MX5100 4x4 with La844 FEL, less than 100 hours, Ag tires. It hasn't been garaged kept but has been kept in a location that doesn't receive much...

Hi Guys, great site, helped me choose my soon to be tractor - a mx5100 hst. I have one problem, the backhoe. In australia, there is some standard that the mx5100 bh92 combo doesnt meet (ROPS...

Just noticed on Sunday that while bush hogging along the road with the left side on the edge of the pavement the tractor wouldn't hold it's line. What I mean is that it requires steering pressure...

I bought a "new" used MX5100 w/FEL almost two weeks ago. Apparently, a guy bought it, took it home and barely scraped the paint of the cutting edge of the bucket and decided he wanted a bigger...

I have a new mx5100 set up with wr long 3rd function and grapple.Looking for step by step instructions for once my bucket is off,and my grapple is on what do i have to do to get the grapple...

Got price of new MX5100 4x4 with fel and industrial tires of $25600.00. With 0% finance. Is this a good price? That was from my dealer that is less than 5 miles from my home

So i finally pulled the trigger price/v.s. needs.That being said,heres the purchase:2013 mx5100,844 fel,qa 72"bucket,R4 tires,rimguard,block heater,1 rear remote,rod level,grill guard.26k.With 4...

Does 8 foot plow sound about right for a Kubota MX5100, mounted on FEL? I have a 7ft rear blade, and the machine does fine with that if chained up.

I have been reading n learning from tbn for a couple of months.Narrowed my choice of tractors down too mx5100 kubota.My concern is im doing mainly grapple work on 200 acres of woods and it seems...

Purchased a new MX5100 a couple of weeks ago and want to know if any other MX5100 owners have experienced a jerky 3pt hitch? With a box blade on the 3pt, it is smooth when lowering and when...

Just took delivery of a new MX5100 HST. Only been able to put about 3 hours on it so far, but really like the power on this tractor. The HST has been great. Only complaint so far is the 3pt...

Lots of threads on the forum relating to pallet forks, but I was interested in learning specifically what brand of pallet forks the MX5100 owners have purchased, reasons for purchasing, and how...

went to a farm yesterday thats selling most everything they have an picked up 3 good feed troughs an 2 mineral feeders.noticed he had a batwing shredder sitting there.so asked if it was for sale...

Looking for any advice and comparison between the MX5100HST and the M5140 hydro-shuttle in terms of performance and fit for doing grapple work clearing brush and trees. Will be using tractor to...

OK, this is small potatoes from the get-go. i love my MX5100 and, all things considered, is perfect. Except for the small item that the distance between the throttle foot pedal and the lever on...

Hi guys this is my first post, I just purchased a 2012 MX5100 2wd and geared last week. My family own a Dairy farming back in the 60's and 70's. They had to sell when I was 13. My farther kept...

Hello to all. Finally pulled the trigger today on my dream machine. An MX5100 4wd, quick connect fel, and gear driven. Kubota is giving a $2,000 discount for cash, and I couldn't pass it up. Not...

Hello to all. Finally pulled the trigger today on my dream machine. An MX5100 4wd, quick connect fel, and gear driven. Kubota is giving a $2,000 discount for cash, and I couldn't pass it up. Not...

Just took delivery of a new MX5100 this past week (thanks again to all who helped me to pick the tractor out). I'm having one curious issue which I thought I might ask opinions of here before...

Reading my owner's manual again, I noticed it says that you are supposed to come to a complete stop before engaging the 4WD. I guess I do that most of the time but there have been occasions when i...

Looking for pics or instructions of a block heater on this tractor or one similar. Thanks

If you have an MX5100 with Kubota rear remotes, would you be so kind as to post or PM me with pictures of the rear remote hydraulic valves? Just tilt the seat up and take a couple of picture of...

Tying to work through all the pros and cons for each of these machines and which one would make the most sense for my needs. Primary use will be cutting 20 acres of fairly hilly pasture land, not...

well i camehome to a heifer laying by the flatbed trailer.didnt think much about it till i turned the water trough off.then i checked her an she had got her head neck an front legs wedged in the...

Narrowed down to either a slightly used kubota mx5100 or a new mahindra 5530. Both have FELs and gears. I really liked the 5530 when I test drove it and the lay out of its controls. I also like...

In July 2012 I bought a new Kubota MX5100DT tractor, manual transmission, no cab, with 844 loader. This tractor replaces my 1947 Ford 8N that I have used for the last 33 years. I have used the...

Anyone ever had problems with their hood latch? Been brush cutting some tall/seedy grass & need to clean the radiator screen every so often to keep the engine temp in normal range. Only way I...

When towing a turbocharged tractor it is common practice to tape an upright exhaust stack shut to avoid having the wind blow in the exhaust and spin the turbo bearing without oil and burn it up...

This might be a silly question but I'm a novice tractor guy and need to lubricate the loader for the first time on a Kubota MX5100. Read the instructions but it only tells you where to lubricte...

After kicking it around for a while, a chance encounter with the dealer led to my buying a unit that had been demo'd at a county fair for all of five hours. It's a gear drive MX5100 with R-1 ag...

a buddy came over yesterday morning an we gave the MX5100 HST a complete service.we greased the tractor from top to bottom.then we drained the engine oil an changed the oil filter.then it was on...

MX5100DT with gear trans and ag tires. Is new at a dealer and has 5 hours on it from county fair use. It has front weight bracket and 5 weights as well as one set of remotes in the back. My...

I have an L4300DT with ag tires that i use for landscaping purposes. I do not have a loader on it and don't want one. But I need a little more power and have been thinking of going up a notch to a...

for those of you wondering if a mx5100 can handle a 3pt 6ft shredder in heavy shredding the answer is yes.i run in low at 1800 to 2000rpms.an the shredder goes through anything i ask it to.you...

I'm new to owning a tractor and just bought a new mx5100. Most of the tractor usage has been using a tiller or a 6ft brush hog. We have 10 hrs on it and have used over 20 gal of fuel, Does this...

i`ve searched but can`t find any info. on how to make a vertical exhaust thru the hood with a 3" chrome stack. has anyone done this or can tell me how to. thanks candyman

Does anyone know how many tonnes an MX5100 Tractor with FEL can tow easily including a trailer?

I'm trying to decide on an appropriate 42 inch pallet fork for MX5100 (quick attach). We want to handle pallets and building materials which typically will be less than 1000lbs, but there will...

Hi All, I read on the forums recently of someone disconnecting the clutch pedal switch to permit starting the tractor without depressing the pedal, having to climb aboard to start is a pain...

I have a mx5100 can someone tell me , draw a picture , take picture , of how the hydraulic lines come off of tractor for the bh90 backhoe .I am wanting to make me a set of remotes set up like...

It' here! After almost buying the L4600 I decided to step up to the Mx 5100. I saw where too many wished they had went with a bigger tractor. I may not be able to eat, but I got the bigger...

Anyone know what the difference between an MX4700 4 / Naturally aspirated and an MX5100 4 / Turbocharged?

Hi All, Got my MX5100 HST yesterday, NICE rig, I traded my L4400 gear tractor in on the new beast, it is a little bigger, more power , love the HST, R4's loaded, QA bucket, canopy, 3 rear remotes...

Finalized a deal today with my favorite local dealer (Phil's Sales and Service in Columbiana, Ohio) for a new B2620 with a 60" MMM. This will be my fifth Kubota in 5 years. I just love getting new...

im going saturday to drive the mx5100 and the m5640. I have finally narrowed it down to these two models. over half of the tractors use will be in the woods with my wallenstein fx90 skidding winch...

Hello to all! I ve been looking on here for awhile and finally signed up. I want to replace my old 3600 ford with a new MX5100 here in the next month. it will see a lot of time in the woods with...

I can seem to find a 3rd function for the tractor and kubota doesn't make one for it. Any info is appreciated

I have price checked two dealerships and have a $1500 price difference. The latter dealer told me he checked with his distributor and his competitions unit is already 2 years old! What kind of...

I am very excited.... going to pick up the new one Friday morning. :thumbsup: I made the mistake of just riding in a M6040 cab tractor 2 weeks ago ..just around the lot. But decided on the...

OK, so you might say I put the cart before the horse, so here is what I need advice on. I own a L3400, great tractor I used it for bush hog, and disk. I bought a new place (41 Acre) soil is more...

OK, so you might say I put the cart before the horse, so here is what I need advice on. I own a L3400, great tractor I used it for bush hog, and disk. I bought a new place (41 Acre) soil is more...

I'm leaning toward the MX5100 for purchase in the near future. I will eventually want a grapple -- and it looks like the most common opinion here is to go with the WR Long one -- and not the...

I just wanted to introduce myself. We would appreciate any advice about getting rocks out of the plowed field. Right now we are stopping the tractor and loading up the front end loader. We took...

A limb got pushed up into the underside of my Kubota MX5100 today and broke off the lower radiator hose connection port. The broken port remained dutifully clamped to the inside of the hose, but...

My buddy at work lives down the road called and ask if I could bring my tractor down and offload a woodstove from a trailer. I said no problem, I'll be right down. Even though it was raining a...

This was done a couple of years back but things have changed since then. The MX5100 now comes with a Hydrostatic option and 2 or 4wd select. Does the L4400 have any advantages over the MX5100...

I cannot decide which to buy. I currently own a bx2360 hst, a New Holland tl80 mech shuttle, and an older MF 255. I want a good midsize tractor to brush hog with, run a box blade, do fel work...

First off, what a great site! Can hardly pry myself away from here at times. I Plan to purchase a new MX5100 this week, and am also looking to purchase a rotary cutter to match the tractor. I...

HI ANYONE KNOW WHETHER IMPLEMENTS USED ON A fORD 3000 tRACTOR COULD BE EASILY COMPATABLE FOR USE BY kubota mx5100 ? I'm thinking of buying used tractor implements when i buy a new tractor...i...

As most know, the MX4700/5100 doesn't come with a rubberized floor mat so I decided to add one before all the paint was worn off the steel deck. This is a 3'x4' stall mat which can be purchased...

I suppose that Im looking for a multi-use tractor that will do all tasks very well. I don't know if that tractor exists. I curently run an old IH 1066, and it's great for shredding the 10 acres...

Does anyone know of any safety and stability issues with using the BH on both these models as in Australia KUBOTA are not permitted to sell the BH 92 on both machines as its regarded as unsafe...

wildkat grapple 48" got the 3rd. function valve from ted installed it myself. got the grapple 3 weeks ago, man this thing is nice have moved logs, brush, rocks & can even pickup pop cans, i don`t...

Howdy all. I'm a new member of the forum but have been looking for info here for several years. We are getting ready to get our first tractor and think we have it narrowed down to the MX4700HST...

well I have been looking at tractors for about a year now since I bought the ranch.. no pun intended. I had my eyes and heart set on the L4240, there just happened to be an AG show these week in...

Does anyone know the price or part numbers for a 2ND set of rear remotes for the MX5100. I asked 3 dealers and have 3 totally different answers. Also the price is over $400 different. Seeing...

i want to install 4 rear remotes has anyone installed there own. what to get & how to install. ? thanks, candyman

Courtesy of Fit Rite Hydraulics! I have to say how easy it was to communicate to Brain any and all questions I had during the research stage. He answered everything within a short time period...

How can I get my hands on a KUBOTA MX5100 HST 4 WD with loader and BH OPERATING MANUAL before I actually order it? I'd like to know more about it before I put the order in, yet it seems to be...

A few weeks ago I posted on here that I was a first time tractor buyer and I thought I had narrowed my choice down to the kubota 7040... Well after scratching my head for a few weeks I am now...

SUMMARY: I have questions about the backhoe bucket width (18" or 24"), what length trailer, tire selection (R-1 or R-4), and backhoe thumb (hydro or mechanical) ME: I own a BX2230 with Woods...

Since i searched and searched for any pictures shoeing the way the hoses are ran and the machine looks with ill post my pics here when I'm done. Should be interesting. Today I will be adding 2...

Hi, I have a 2005 MX5000 and the book says it is category I/II. I am in the process of making a tipping box and need to know how wide to make the lower links. Cat 1 is 26" wide, Cat 2 is 32.5"...

If price was no object (I think there's about a $5,000 premium for the L5240 over the MX5100) is there any reason why I should buy the MX5100 instead of the Grand L5240. Both would be HST and open...

Im trying to decide if I buy an 8ft blade for the 3pt is gonna be to big if I ever need to rotate the blade 180 Degrees (from pulling with it to pushing with it). Or is the 7ft the better fit?

I am trying to determine whats the advantage of a turbocharged tractor ( which I have never owned ) vs naturally aspirated. I have an L2500 now I am selling and trying to move up to something...

Well I have all of 3 hours on my machine in one weekend and managed to hit something on the cover that is suppose to protect the tie rod/power steering rod. Put a nice dent in it which proceeded...

My new MX5100 is category 1 and 2 rated. The three point hitch has category 2 mounting links in the lower arms, but the top link swedge tube has a category 1 mounting hole. I have three bushings...

my tractor is 1yr old today,an it has close to 90hrs on it.an the tractor has been great trouble free service.an it has done everything ive asked of it an more.the loader handles the 5 by 6 bales...

So I have finally done it. I purchased a 3 bottom plough about a week or so ago from a local guy who resells old used farm machinery and other items. I was about to give up finding a used one as...

My new MX5100 finally arrived late this afternoon. I did two laps around the orchard with the FEL on, and then did two more laps with the FEL off. All total I put one hour on her. Didn't go above...

Thinking about this unit with cutter only for 10 acres. Not needing a FEL until I build on the property at least 3 yrs from now. Best price I have gotten is around $22,100 with a canopy and...

Just a short update on my first weekend with the new tractor. First things I noticed: - size...a lot longer than my B20 and have to watch the loader doesn't hit anything - power...plenty of it...

Thought I would do a little contributing here... Sold my B3030 last year and picked up a new MX5100. I really liked the B3030, but found that it just didn't weigh enough for what I was using it...

It was delivered today. Unfortunately they forgot the BB and I'm currently awaiting delivery for that anytime now. Yes I know pictures are required and so far have only taken this one: It will...

I closed a deal today on a new MX5100. I'm going with R1 tires, QA bucket, and an FFC 84" Hyd. Angle front blade. This thing caught my eye at the local fair in early September. It was love at...

maybe i`m in the wrong place i searched for the above & found nothing. i want to install it on my tactor i have a loader on it. don`t have a clue what or whos equipment to get & also i want to get...

So Monday is the day I sign for my MX5100 with BH96, R4's, toothbar and Bushhog MBX72 BB. I've sold my B20 and should have the MX by Friday. Can't wait, should be an interesting day and I'll be...

I purchased an new MX5100 HST, 4WD, with loader from my local dealer August 16th of this year. I love the tractor and the way it performs, but it is so noisy I am forced to wear ear plugs when I...

looking at renting a notill drill to put in some winter pasture.my tractor salesmen is looking into a 6ft 3pt notill drill since he wants me to pull it with the MX5100.will it be to heavy for the...

I sure underestimated the size of tractor I needed back a few years ago when I bought my first Kubota (BX2350) I just turned over 500 hours on my L3700 to find out I will need a larger tractor...

I have a lead on a 2011 MX5100 which is the model I have been planning to upgrade to since the Spring. It has only 134 hours on it and was used solely to pull a wagon/trailer at a garden centre...

Hi everyone. Need some help from u guys. Today I have an BX24 which Im very happy with. But sometimes it too small. For example I need to get a "trailer" with a hydralic crane to do some work in...

Hi everyone. Need some help from u guys. Today I have an BX24 which Im very happy with. But sometimes it too small. For example I need to get a "trailer" with a hydralic crane to do some work in...

IM buying a mx5100 this week and am thinking about remote hydraulics. How hard are they to install later? there expensive from kubota and i'm not going to need them right away. Eventually i want...

Hello Just wondering if any mx5100 owners have pulled a mower/conditioner (haybine) or any disc mower? I imagine a small sq baler is no problem any one do any small rounds? I still trying to talk...

Hey guys, I've never owned a tractor, but we just bought an RV Park and need a tractor to do the following things around the park: 1) Spread Mulch 2) Spread Pea Gravel 3) Spread Gravel for Roads...

After all the rain here in Indiana finely got my hay baled 13 acres . This was the first time for me it was clover and grass mix thick . Long dry time ground was still damp under hay but got it...

A couple of questions for those that have gone from a Lxx40 to a MX. I'm wanting/needing to go to a larger brushcutter. How much do you miss the features of the Grand when going to a MX5100 HST...

I was at the dealer today pricing a grand L 3940 and the dealer wanted to show me the MX5100 saying it was more tractor for about the same money. Can you offer me comparisons as to what I'd be...

Just a quick introduction from Tennessee... Recently got 100 acres to play around with. After shopping tractors ended up buying a Kubota Mx5100 4WD with FEL and backhoe. Not sure how much I'll use...

Hey folks....I bought a new MX5100 back in Feb.It has the LA844 loader.I need to pull it to the deer lease and my trailer is only 16ft long.My dad left it to me when he passed away.I plan on...

After borrowing my sisters John Deere 870 for the last few years I decided it was time to pick up my own tractor. After researching for a couple of months I decided the tractor for me was an...

I know there are a number of members who have the MX5100 and I am currently targeting the MX4700 just because it's near the top I want to spend. I know the differences between the two are: - 4...

Good afternoon guy's, I just joined this forum looking for some feedback/opinions on these two tractors. My dad is currently in the market for a Kubota tractor and has narrowed it down to these...

It was a few months ago.. but took delivery of a MX5100 4x4 hst with FEL, draft control and 1 rear remote, 6 ft shredder, 6 ft disk, 6 ft box blade and front hay fork. Upgraded from a almost new...

I have 75 acres that is mostly flat, dry and woods. I use a tractor for bushhogging, planting food plots, etc. I currently have a IH 384 and it handles all of my work but seems a little under...

My MX5100 with FEL arrived 3/19. I also purchased the HD bucket. I put about 3.5 hours on it Saturday, I cleaned-out part of the barn, and cut some brush. So far, so good.

After considering a L3800 (or deal on a L3400), I think I've decided on a 2011 MX5100. I have 50 acres of both field, pasture and wood and a 1,000 foot drive and decided the 5100 is generally a...

In 25 words or less: what is the difference in these two machines? Simple answers like "$5K" is not what I am looking for. I want to know how important the "deluxe" features are. Any insight...

I'm planning on buying the MX5100DT, 4wd with FEL and AG tires. The dealer says they usually fill the rear tires with methanol/water, but if I want the front filled they will do that as well. I...

Interested in the opinion of others on this tractor. 2008 Mx5100 gear drive with FEL. 221 hours. Single owner. At the local JD store. They are asking 19,500. Is this a good price? Seems a...

Trying to decide if this is a good enough tractor for me. I have 86 acres with 15 acres of woods. I will use the tractor to haul wood to the house with the FEL and the 3 point hitch. I have...

I've been lurking for awhile, trying to figure out a few things before purchasing a tractor. The tractor will be used for clearing snow out my 1/2 mile driveway in the winter, some brush (grass...

I have read were the mx5100 is a fuel drinker. Is this true and if so how do the l4400 and mx4700 do. I'm real close to pulling the trigger on one of these models. Please advice. I dn't wanna...

I'm getting closer to choosing a tractor here. I started looking at the Deere 4105, but because of weight, only 2 range, no independent brakes, and no folding ROP's, I got away from that one. I...

Simple question. Should I get a 6ft or 7ft box blade for the MX5100? It's got R4 tires that are filled and it's got a loader. Just wondering if 7ft. will be too heavy to pull. I've got the...

What should I look to pay for an MX5100HST with FEL and loaded rears? I would be using the special finance offer and not cash. - Dave

Hi everyone. My head is spinning here from all the information. I have a horse farm that I need to do some loader work, mow 5 acres with a finish mower, drag a horse arena, and plow some snow with...

Just purchased a MX5100 HST 4x4. While searching around the last couple of months, I have been debating on Hydraulic top link. I am having 2 sets of rear remotes added. I opted for one, then...

I went back to Kubota dealer and this is what I may be getting. MX5100 HST 4x4 FEL Box Grater Rear Remote Tires filled(Some Kind of...

i just bought a new MX 5100 HST 4x4 with 855 loader.an i was wondering who here has 1,an your thoughts on it.i use mine as a back up tractor.an itll lift 5 by 6 bales with no prob.an itll also...

I just dropped my tractor off today for a single set of rear remotes. Dealer price installed is $750. I looked at some different options, but decided to go the factory route. Who has the best...

with a kubota 74" snow blower, ice chains, 351 farmi winch, and Wallenstein BXM42. With promised delivery before the new year. Thanks for all the info from you people, it helped in my decisions...

I've a new MX5100, but bought it with no frills. Now that snow removal season is here, I need to add a rear light so I can see to run the snow blower after dark. Any suggestions/experiences...

I have a relatively new (1 month old) MX5100 with front end loader and a 3rd function remote installed for a future grapple or thumb. A friend of mine has a 3ph hydrolic log splitter that he...

I have a relatively new (1 month old) MX5100 with front end loader and a 3rd function remote installed for a future grapple or thumb. A friend of mine has a 3ph hydrolic log splitter that he...

So I put together what I would consider a sizable package deal. It consists of the tractor with a Q.A. H.D. F.E.L. with replaceable cutting edge , extra valve and plumbing, ice chains, logging...

I'm looking at a new MX5100DT with the FEL, Ag tires, 4WD. I am looking at a price of 25,600. With the $1000 off cash incentive program from Kubota it comes to 24,600. I'm told MSRP is 28,310...

I've been posing some scenarios here on TBN for a few days with some great responses and I'm getting a little closer to making a purchase. I'm hoping to get the same quantity and quality of...

Can someone tell me if you can get floor mat for the MX5100:confused: I haven't asked my dealer yet. I know it would probably be more expensive getting it from the dealer. Any ideas would be...

Well I took delivery this morning of my new 2010 MX5100 HST. I got the quick attach FEL, and bucket, and 4X4. I got the R4 tires and had the rears loaded. It has the grille guard and best of...

Can a Kubota MX5100 (50hp) handle a 7 foot rear grader blade? Will be used for snow removal. Manual says 72 inch maximum! Kind of surprised! You would think a 50 hp tractor could handle more...

I normally use Shell Rotella T. The manual that came with my new MX5100 states: The CJ-4 engine oil is intended for DPF (Diesel Particulate Filter) type engines, and cannot be used on this...

Hi Everyone! I'm the proud new owner of a MX5100 HST. I will need to get a wood chipper and am looking for recommendations on brand and type. I will be using it a lot since I have 107 acres of...

I'm in the market for a 50 hp tractor, four wheel drive, with a loader for my farm. Will be used only for mowing, dirt, gravel moving, etc. No hay bales or such. Leaning towards a new 2010...

Which would you choose? Same tractor. 5100 has turbo and 50 hp and the 4700 non turbo and 46 hp. Telescoping 3 point links on the 5100 and non telescoping on the 4700. 4700 $1k cheaper. Thanks...

I'm new to the tractor world and purchased a MX5100 with FEL, Ind Tires and Canopy. I also got a Land Pride Cutter RCR 1872. I have about 100 acres of mostly wooded land, about 15 acres to bush...

Dose any one use a 7' a three point bush hog with a mx5100 if so how dose it do ? I'm going to mow a grass field about 12" to 18' high . If it works what gear do you use

I really like it, it has plenty of power. It did great with the bush hog and the 8' disc. Some of my buddies looked at the smaller stature of the tractor and said that there was no way that it...

I just bought a new mx5100. I need to know witch tires to get R4 or ag tires? I have 50 acres and 12 acres at my house lots of hills and rocks. I don't have alot of snow to plow. I live in the...

Trying to sell my setup mentioned above for 22,000. I think it is a very good price, but have been getting a lot of folks saying it is too expensive for them. The tractor has 83 hours and in...

Coming up on the 100 hour service for my mx5100. Any idea what the local Kubota shop may charge for it?

Well, I finally ditched my old tractor and bought a spanking new MX5100 out of necessity. I have a 2.5 mile driveway that winds up over a mountain to our property. I was totally snowed in (over 60...

Stop at the local NH dealer who recently picked up Kubota, for parts for my haybine and took a look at a MX5100. Was impressed at it's simplicity. I am curious if anybody uses one for carring...

I got a new MX5100 with a LA844 loader yesterday. Only had 30 minutes on it so far but am not impressed with the lifting power. The loader will not raise if very full of dirt. I also tried pushing...

I have a new (50 hours) mx5100, and so far its a great tractor. However, I keep reading mention of hearing the turbo spinning down, and I don't think I'm hearing it. How obvious is it? Also, the...

My fiance is looking for a tractor. He is going to do alot of landscaping type work and will be using a front loader, a box blade, an auger, a scraper blade and a tiller. He will be doing this for...

I am new to this website and very "Green" with respect to tractors as well. I am specifying a new Kabota MX5100 with a FEL, rotary cutter, disc, post hole digger and box blade scraper. I was...

I am new to this website and very "Green" with respect to tractors as well. I am specifying a new Kabota MX5100 with a FEL, rotary cutter, disc, post hole digger and box blade scraper. I was...

I finally decided to buy the Kubota Mx5100 Dt with ind. tires, Fel, and 1 hydralic remote. I bought it for about $24,600. now im wondering which brushhog would be the best for me. I have to do...

I'm looking for an additional tractor for bush hogging the pastures. I want 40-50 PTO HP. I currently have a 6' brush mower, I might consider upgrading to something a bit larger but will...

I'm looking for a new 2WD tractor primarily for bushhogging pastures. Something to run a 7' mower. I've had good experience with Kubota over the years and have been looking at the MX5100...

I have narrowed my first tractor down to a M5040 (2wd) with FEL and the MX5100 (4WD) with FEL. I have received a quote on the M5040 for $23,700.00 and $22,900.00 on the MX5100. Both quotes...

I am looking to purchase a MX5100 (4WD) with FEL. Looking for any opinions, experience, or problems with this tractor.

I was pushing some underbrush with my FEL a few days ago and managed to knock my fan blade belt off with a limb. I am not sure how long it was off but I noticed it right before the temp gauge...

I'm looking for input between 2 tractors. The L4400HST and MX5100, I will be mowing roads and acreage. The MX5100 is $985.00 more but I think it for the extra HP it is a better deal. Any input...

Bought a mx5100 last year and so far it works great. This year I need to find the largest cutter that the mx5100 can safely pull. Looking at 10' cutters but curious if that is to big of a...

I have been looking into upgrading tractors and have come across the MX5100 with loaded R-4's. I would mainly use it for property maintenance on 50 acres of woodland and snow removal. In time I...

I've been shopping for a 45-50 horse 4wd utility tractor for a few months. I'm new to tractors and Kubota, so I could use some help. I'll be using it in the woods a lot, planning to buy a 3ph...

I've been shopping for a 45-50 horse 4wd utility tractor for a few months. I'm new to tractors and Kubota, so I could use some help. I'll be using it in the woods a lot, planning to buy a 3ph...

I'm getting lost in the specs and finding it difficult to compare these tractors. I do lots of loader work and bush hogging. also comparing 400cx loader to la854. To anyone that owns a mx5100 is...

I have a 4 acre field I am going to plant hay in and harvest it myself, then there is the neighbors field that is 8 acres that I am going to try to lease to grow hay. I know I have to prep the...

My new tractor (one of the above, as of yet undecided, buy bought early this week!), will require turf tires for some commercial landscaping work once per year. It sounds like there are a handful...

As mentioned in my other thread regarding round bales- I am 2 days away from putting money down on a new tractor. I'll be getting a gear, 4WD with ag tires. The main job for this tractor is farm...

I'm 2 days from putting money down on my first new tractor. I'm still caught up on the L4400 vs MX5100, (5100 is on backorder while 4400 is on a good discount being a 2007 model)... With either...

are there Hydralic remotes for the mx5100dt

We have 20 acres we have to grade a 600ft driveway,some heavy brushoging,and move about 60 5 by 5 round bales in the winter.Would the Kubota MX5100DT be good foe our situation?

I'm in the market for a box scraper for my Kubota MX5100DT to repair and maintain about 1400 feet of gravel driveway. Any suggestions on what brand and model would be a good fit for this usage...

Hi, I'm looking to make a purchase this week and its basically narrowed down to the New Holland TT60A and the Kubota MX5100, both 2WD, mostly to be used for 72 inch bush hog and FEL (light to...

Continuing the tradition here, I thought I'd share some pictures of my recent purchase, an MX5100. Having never owned or sat on a tractor before, I was a bit intimidated when it was delivered and...

I've looked at (and driven) these three tractors that are in stock at a local dealer. All are about 45 PTO HP and any of them would do what I need (bushhogging, moving dirt/stone/snow...

Yesterday was a great day, we became the proud owners of a MX5100 What a nice tractor for the money! It's equiped with 4wd, LA844 FEL, grill guard, dual rear hyd, work light. Our local dealer...

Buying my first tractor is becoming more stressful than buying my house. I have looked and read and been to every dealer around. I think a couple of tractor salesmen are actually tired of seeing...

I am lucky to have two Kubota dealers within 30 miles of me. Have been looking at the MX5100 Dealer A gave me a written price proposal for the one on his lot. It has 1 remote, LA844 loader...