Have a BX25 with 500 hrs. I get a clunking sound from the front axle. Hard to say if it's from from changing directions or turning or a combo of the two. Fluid seems to be full in the axle. Or...

Twisted dipper stick, any suggestions on where to get a replacement, hopefully used? Anyone tried straightening?

Anyone replace the alternator/fan belt on their BX 25? Before I pull the drive line to get the old belt off and new belt on lower pulley it would be good to know if there is enough end play to...

Walked out the other day and heard the bx clicking.. constant clicking noise. Turned the key on and off and nothing changed. Turned the light switch on and it quit. Started and drove it a bit...

Finally got some time to try a new BX25 toy yesterday. WOW. I'll never use my auger again! I slammed about 25 6" posts in a few a few hours but still have a few hundred to pound. It took...

I’m looking for some advice/thoughts/anyone with experience on the following. I’d like to add rear remotes to my BX25. Looking at hydraulic valve kit options from both fitrite hydraulics and...

I was mowing last night on a slight slope, and thought my mower deck became disengaged because I felt a "rubbing". It turns out my left rear wheel fell completely off. What was especially...

I just did my spring re-mounting of the 60" cutting deck, something I only do once a year, and therefore kind of hard to get good at. This is of course the drive over deck, and in the ads they...

Is $14,000 a "good buy" for a 2017 Kubota BX25D? It has 213 hrs. on the meter, and it's equipped with the FEL, Back-Hoe and 60 inch belly mower. It looks to be immaculate, and the original owner...

After 11 years and 1100 hours later the ol workhorse has served its purpose. The dealer will be here in the morning to haul her off after dropping off the new LX2610. We are needing greater...

I've been wanting a higher steering wheel on my BX25. Does anyone know if one of the taller wheels like on the BX25D will fit the BX25? Thanks.

Has Kubota BT601 backhoe, says quick attach model, have several posts on other BX models where satisfaction with backhoe and mid mount 60 inch mower are biggest frustration for...

So found a BX25 listed for sale. Talked to the owner. Second owner and he said he bought it after first owner rolled it. Has used it about 15 to 20 hours as is. Says it puts out white smoke for...

I've had back issues for 50 of my 72 years so the lack of suspension on the BX25 is an occasional problem. This year already I've been down 4 times so I thought it was time for some suspension...

Out tilling this evening and BX25 seemed a little sluggish backing up a few times, but forward seemed to have been fine. Thought it might have been an issue with tractor being in low range so...

We are moving from California o Northern Wisconsin. I had planned to take my BX25 and and RTV900 and use the tractor for snowblowing and general property cleanup and maintenance. However, it...

Hi all, starting to put together plans for my pole barn project. Gonna build a 40x63 with 14 foot side walls. Gonna do all but the concrete myself, planning to start in July and finish before...

This is my first time posting a forum, so this is a new experience for me. So here we go, I am looking to own my first Tractor. I have been researching and studying for the last 2 years trying to...

Hi all, new here, been looking at tractors for a few weeks. I'll be doing driveway work, land leveling for pole barns, landscape gravel work and other odd jobs. I'm a auto technician by trade and...

Does anyone have a part number for a BX25 floor pan? Mine is rusted out pretty bad and I'd like to simply replace as opposed to trying to fix it... thanks

I thought I had done my research and I chose some hydraulic fluid called AW46 to use in my BX25. After I bought it, I looked online and started seeing some places selling AW46 and they said it...

The hydraulic fluid is at the full level. I have tried moving the deck up and down after removing the four backhoe lines and it does not move. I looked at the power beyond connector and inside...

what is the resin for removing mowerdeck when using backhoe on BX25

I started it up when I arrived at the cottage last night, and it was about -13 Celsius. after running it for a couple of hours, I stopped and plugged it in, and then this morning, it would not...

So I settled on a like new 2008 BX25 with 172 hours (I know, right!) backhoe, FEL, and belly mower. I spent 12 hours on it this weekend putting it to work back filling 400 feet of 3' deep trench...

Got some of the leaves up before Old Man Winter decided to snow!

While the new BX4090 cab is officially for the 80 series tractor, would it fit on a 60 series BX25? What's important is the shape and dimensions of the floorboards and rear fenders, if they are...

Hello all, I did my 400 hour service on my Kubota BX 25, but now it’s up to 765 hours, and I am thinking it is time to service it again. The question is, is $600 to $700 reasonable for complete...

2013 BX25D with apprx. 200 hrs of easy residential use. No previous FEL issues. No FEL cylinder or control valve external leaks. FEL falls under its own weight. It does stop eventually I'm...

Is anyone using a 6' blade on a BX25 (has Pat's quick connect on 3ph)?? I will only be using it for back dragging my driveway and any snow we might get. I won't be using the cutting edge but a...

This is probably old news to most readers but I’ve received lots of helpful tips over the years so thought I’d post it anyway. I removed the rubber mat on my middle aged BX and found a reasonable...

Hello all.First post for newbie here.Have enjoyed reading here for months now.Ready to pull the trigger soon on one of these units.Used 2008 kioti ck 20 hst,front loader,3 point hitch, 680...

Hi all, Another issue with my BX25 lately. The bucket will not stay up unless I keep pressure on the controls to keep it up. I have NO leaks anywhere, connected and reconnected all fittings...

Good evening, Had a little issue with my machine after plowing an hour ago, went to turn the key off, tractor kept on running. Lights also stayed on, factory lights and the LED light bar I...

My BX25 does primary duty as a dirt digger/mover and when I bought it (used) a month back I had the tires filled with Rim Guard immediately. I run the recommended 18PSI front and 22PSI rear...

The question is how big of a step up is it in loader/backhoe digging ability when moving from the SCUT BX25D to the CUT B2650? My primary use is finish mowing lawn (2.5 acres) and then the other...

My father owned a home construction for years and used large equipment, one item was a large old Case loader/backhoe that they used on job sites. So when I picked this little Kubota BX25 up, he...

We got the BX last week used with 93 hours on the clock and noted that the 50 hour service was not completed. So the start was to run to a dealer and buy all fluids for engine, front axle and rear...

I just picked up a real cherry 2013 BX25 with 92 hours on the clock, and being an older model it has a pin on loader bucket. I would like the option of dropping a SSQA bucket and mounting up a...

Okay, so yesterday I get a lead on a tractor.... because you know.... I've been talking about buying a tractor to anyone who will listen for at least 2 months and everyone knows I am looking...

I've posted a thread about the dealer saying I have gas in my diesel fuel. Still dealing with this, seems they say I need a new engine. But This is another situation. I'm hitting this engine deal...

This is a revised version of a previous quote that did not get much response. I bought the thumb on CL at a real bargain. Owner bought and never installed. No instructions. His BX 25 is same...

I have a new Kubota brand BH thumb I bought on CL cheap. Does anyone out there in TBN Land have the instructions for installing these? Has anyone installed hydraulics to one? Pictures will help...

I have a BX25 and use a rear blade and box blade. A hydraulic top link and tilt link would be great but I cant find any info specific to the BX25. I would think you could use the supply and return...

Hi - I have a BX25 and no Mid-Mount Mower - my question is - how can I keep the linkage/arms all the way up all of the time ? It was not obvious looking under there how to physically lock them in...

Some ideas please on a safe way to relieve the spring tension to remove the belt. I have had a bad experience on another mower trying to remove the spring. Messed up a finger pretty bad. When I...

Hi All, pretty new to this forum. I have a 2014 BX25 with the backhoe & the FEL. I also have a snow blade and use the tractor mainly for plowing small projects around the house. We just bought the...

Can anyone share their insights on the new BX23S backhoe capabilities? I'm strongly considering the BX23S. I don't really need tractor capabilities, more interested in the BH. I need to decide if...

Of all things, you would expect a seat belt to work flawlessly. I am beyond livid. Today I laid my BX25 on it's side, a slow plop over and I could NOT get the seat belt buckle to release. I am SO...

Hi, folks, my very first problem with my 2009 Kubota BX25. The tank was down to about 1/4 or so and I filled it up with some fresh diesel I just bought on May 19. Started it up and it warmed up...

Hello, guys, my 2009 Kubota BX25 seems to have lost a LOT of power to drive up even a slight incline, especially in reverse. For example, I was back dragging some very light, sandy soil up a VERY...

Seems something broke, as the differential lock is partially engaging. I have 1600 hours on the machine and engage the differential lock often, but before I have a traction issue. Unloaded, I...

Sorry to bug the forum on this, but being as I am out of town, I cannot measure two dimensions I need on my 54" mid mount mower deck. I just ordered a Cyclone Rake, and they are asking for the...

My kubota bx25 bucket has a lot of play. When I lift the bucket up and tilt the bucket down, I can move the bucket up and down with my hand. I am unable to use the bucket to lift I blew a hose and...

Hi All, I just discovered the new BX23S ('17 yr model) tractor, loader, backhoe package. I'd like a mid-mount mower also, and eventually a few other options ... post hole digger, pallet forks...

Hi all, I have a BX25D with about 25 hours on it. The backhoe is very fast, abrupt and "bouncy" side-to-side operation but smooth in all other axis and movements. Is there any way to adjust or...

I am looking at buying a BX25 asap. All dealers around me are at $18240 out the door NH resident(no sales tax). This is the no haggle, email through site. Anyone getting the prices lower? I...

Well, I stared working at my cab build project for my BX25 last weekend. Plan is to have a single door on the left side as well as a removable rear window to allow for use of the backhoe with...

Do any of you know of a front weight bracket for the BX25's? Maybe built one? I put a EA aerator on my BX25 and while it works great it also causes the front end (wheels) to lift about 18" off...

So I see there are 3 unused holes for mini fuses in my fuse box on my BX25. I want to add circuits utilizing these future holes. Can someone clue me in as to exactly what kind of connector I...

Hey all. As Spring approaches on our first full year on our new homestead (2 acres of lawn, 10 acres of woods, and 55 acres of pasture), I have decided that a good tiller is the next implement...

Quick question, I have a BX25 which spends most of its time as a mower without the loader and backhoe attached and with a MMM deck on. If I want to do some grading or very light work with the...

Guys I know there is a lot of incredible talent in the TBN welding section. I perhaps should have posted up what I am doing here but gray matter does what it does sometimes. If any of ya'll...

Well, a new piece of property and some new challenges. SNOW! ...and how to get rid of the stuff! Well, I have another crazy idea and hook or crook I am going to do it. I should have the ability...

Has anyone used a HD aerator on their BX25? I was wondering if the Everything Attachments 650lbs units are too heavy in real world usage. I know that is close to its lift capacity but like the...

First post here. After years of wishing for a tractor to manage and clear the yard and woods (only 2 acres) I found and bought a 2013 BX25 TLB with the 3 point linkage and an aeriator thrown in...

Incase anyone was interested, hard to find much about it. I needed more grip.

VERY upset I am at the quality of the tires on my BX25. I think I was one of the first to grab one of these jewels about 5 years ago or so now. I looked at the rear tires a couple of days ago and...

The BX25D really has caught my eye, mostly from viewing threads here. I feel I need to know more and how it compares with slightly bigger and slightly smaller models. Are those a better deal? I...

I have a 2015 Kubota BX25D that I bought used. 108 hours. I can not get the bucket to curl, pull the rake in, and boom up at the same time. (Basic Digging):confused2: I tried it at 3500rmp...

Can I put BX 25 wheel assemblies on my 2005 BX23 with no issues? Not sure I can still get them but if nothing else I need to by new front tires before he snow flies. I am running the stock AG...

Lots of posts on "What should I buy?". What I would like to hear is "What were you displeased with and what do you wish you had bought?" Yes I am shopping serious for a PHD for a BX25. Los...

I have a Kubota Bx-25 and also have an extra trenching bucket that someone cut the brackets off of. Does anyone know the hole to hole measurements of the mounting pin holes for the bt601 backhoe...

I've loved my BX25D thus far with a few exceptions. With my current project though (clearing land), I'm thinking about upgrading. I'd like to keep a MMM so that means the B series. I'd still...

My BX25 w/ custom roll cage might not fit in a shipping container. I am shopping for a pair of cheap rear rims I can swap on just to load into a container. Send pics and price and whereabouts...

I'm sure all the senior members here are tired of these posts, but I really am torn about what to buy. I just bought 5 acres and will be needing to mow, dig trenches for utilities (cable internet...

i sure picked a hot a humid day. other than that, everything went well. the front axle oil was a bit dirtier than i expected, then again it's not filtered. hydro fluid came out looking like...

hey everyone, I am in the process of working out a deal for a new bx25. I am finding a better deal at a dealer that is farther away. They are saying that the kubota insurance pays for pick up and...

Hi Everyone, I did a search of the forum on this subject and didn't find anything. I apologize if this is a repeat. I have a 2010 BX25 with about 650 hours on it and it seems to run hot when...

I am a new member. Doing a pump fan replacement and finding it hard to remove handle rubbers, deck height knob and hydro speed control knob( I already broke this one.) pulling rear fenders...

Hello everyone.. I just finished doing a complete service on my 09 bx25. Changed hyd fluid and filter, cleaned screen and filled back up, used super udt2 fluid... I checked the pressure a couple...

Hello everyone, ive been lurking on here for awhile now gathering all the info i can on bX tractors. I was intially going to buy a new bx25d with 60" mmm only as i dont need any other implement's...

I got the BX new in 2010 and it has about 650 hr. on it. When it was new, and for years after, it would start cold with a 10 second or less glow plug warm up. It would fire right off. For the...

I know that backhoes on BX2200 has been the subject of topic many times on here, and believe me, I have probably read every one. I'm aware of the pros and cons and without belaboring any points I...

The 4" septic line from my house to the septic tank is around 10ft long. From the house it starts out cast iron and about half way to the tank, switches to what we believe is terracotta pipe...

Hello all, my Wife says go ahead and upgrade!:drool: (She's a good wife, to be sure.) But is it worth it to upgrade? I have a 2009 Kubota BX25 which has served me well, doing everything from...

I was all set to buy an XJ2025 and then I noticed how far under the backhoe frame hung under the tractor. This looks like it totally negates any ground clearance the XJ2025 has. In fact it looks...

My bx25 is broken down 1000 meters from my garage can I safely tow it to my garage using another vehicle. what do I need to do to prevent damage to the engine/ tranny

Hi Guys, this is my first tractor so I don't have any idea whats normal or not. I've had a few teething issues with my BX25 so not taking anything for granted. Hoping you can tell me if your...

So here's my problem, in the middle of a snow storm. I started to clear my driveway and my Kubota was running fine and then all of a sudden it started to bog and sputter and shake. Then it would...

Been using my PHD for several weeks and went back to install the BH and after hooking up the 3 lines I can't get the stabliziers or bucket arm to raise. Unplugged the 3 lines 3-4 times to no...

Dealer wanted nearly $400 for the BH thumb on BX25D. Seems like a lot for such a thing. Any recommended alternatives? Thanks

I just mounted my BX5450 blower on my BX25 with my BH still on. Just wondering if anybody leaves theirs on also. It seems a bit tail heavy, not bad. My thought was to leave it on for better...

This is my cab for my bx25. Need some snow to try it out.

I want to make a 2 ft trencher for my bx25d. My issue is that I only have 17 inches available in order to complete the curl to put the trencher away on the backhoe. I have a quick removal for...

Hi Everyone, this is my first post to the forum but I have been studying it for a while. I am a campground owner in Nebraska and currently own a well maintained (800 hours) 2007 BX2350 with FEL...

Ok, so I scoured the net looking for ideas for a quick attach for my bucket but I liked some features of some and some features of others. I liked the 2 inch receiver built in from one I saw, but...

I bought my BX25 for my 1 acre lot and still use the belly mower, bucket, and BH regularly. I love it. When we bought our 8.5 acre property 2 miles away, I decided that the BX25 would be...

I found a used Woods LR72 (6ft) landscape rake that is in good condition. Tines are a little rusty, but the rest of rake is in great condition . The guy is asking $300. I think the price is good...

When I try to start my BX25, the starter doesn't engage and the information lights go out. After I turn the ignition switch to off, the information lights glow dimly, a little buzzing sounds goes...

Found one local in good shape, is it to much for my bx?

I have been doing some reading on trailering a BX25TLB. It seems that the perfect trailer is about a 16' car type trailer. That is fine, but its not going to work for me. I currently own a 5X10...

Gonna start looking for a deck and bagger for leaf clean up. Are all BX decks interchangable? I know theres atleast two different bagger options what parts work on the bx25? Thnaks in advance

Hi folks, Long time reader and I'm finally at the point that i've started shopping around of my very own Kubota. About this purchase: 1. The BX is the only line that will fit at my current...

Greeting, I need to move 10 yards of #57 bluestone which will be dumped on my asphalt drive with my Kubota BX25. I'm thinking I would be better off removing the Piranha bar from the bucket in...

Does anyone have an older bagger they mounted on the BX25 (or a new one setup for a BX25) they could snap a photo of the mounting system and how it works? Kubota offers a retro fit kit and I am...

I went to remove my BH bucket, with plans to install my ripper tooth. The first pin came out like expected, but the second wouldn't budge. I tapped on it lightly with a copper rod, no effect...

So I picked up a BX25 a little over a week ago and have put on bolt on bucket hooks, a Piranha tooth bar, and about 8 hours so far. Now looking for storage options and ideas with the limited room...

Greetings, anyone tried the new trencher bucket and QA bucket adaptor? Wondering if the QA changes the bucket geometry or curl in/out. I've already got a ripper tooth and am ordering both...

Hello, I bought a low hr bx25 and noticed the main cylinder on backhoe boom will sag when parked (overnight a couple of inches). Is this normal? If not , how can I address? Thanks!!

Hello all, I just bought a Landpride RCR1248 3 pt mower and I cannot get it adjusted right. Hoping someone can walk me through my troubles. I am trying to get the front of it adjusted so it...

I purchased a TS 4' Box Blade on Friday. Pulling it behind Britney. I live on a steep property. I dropped the backhoe (first time) at one of my parking spots up the hill from the house...

Looking to purchase a trailer for my bx25, whats the smallest size it will fit on and does it have to be a double axle?

I have about 80 hours on her now. Love the machine. This weekend, I was working on the property, and picked up a bucket of rock and dirt. One of the boulders was sitting out to the edge of the...

The forward and reverse speed has dropped considerably! After changing the HST fluid, filter, cleans the screen, still no change in the speed. So, I now suspect it could be the HST linkage. Has...

Hi New to the forum and new to tractors. I own 2 acres and getting ready to turn 60 so decided to get something to help with the heavy lifting. The kabota BX25 seem to fit the bill with the...

Well after having my bx25 since January 2010 an after several times removing the step mat to clean underneath an to service several items my step mat has tears an was just warn out. So after...

I'm wanting to build a dolly (wood)for my BX35 FEL and BH. Has anyone done it, ate the any suggestion, videos etc. available

What is the best valve to use for rear remotes on a BX25? I see the specs on the 60 series tractor is the max GPM is 6.3 so the valve does not to be a high GPM model I presume. What about this 8...

Here in SW Missouri we have some very rocky soil. Can anyone with experience with a BX or similar tractor share their thoughts on digging in rocky soil using either the backhoe or loader?

This is a wallnut tree stump I pulled with my BX 25 It was so big I had to roll it out of the hole after filling in half of it to make a ramp

I have a 2014 BX25D, it is leaking about 1 drop a day of hydraulic fluid a day from the bottom of rear PTO shaft housing, the same housing that the PTO guard mounts to. Yes it's under warranty and...

For those that use the vacuum cleaner while removing the transmission strainer on a BX. Do you hook the vacuum hose tightly to the dipstick hole? If so do you have any problem sucking up fluid...

I'm looking for opinions from anyone who upgraded from a BX25 to the small size B, I'm specifically looking at the new B2601. It's more money than I figured it would be to upgrade after talking...

Hi, guys, does anyone know where I can get a reasonably priced removable tooth bar for my 2009 BX25? The BXpanded one will cost me close to $400 after the shipping, 20% exchange rate, and...

Hi, all. I have the BXpanded BH dolly, thumb and bucket expander and I am VERY happy with all of them. For my b'day, I've asked my wife for the under armor and the ROPS tool kit. What I am most...

Need help with hows to measure shaft. Also I have the shaft split right now the tractor half is hooked up, the tiller half only slides over shaft about 1 inch , this cant be right am i missing...

:mad: Please forgive me in advance, but my whole tractor buying experience has been a giant exercise in frustration. I have a unique property that is very steep, and has a ton of stuff that needs...

I am digging out the hill under my deck and pouring footers then handing off to a friend for block and brick walls. This thing kicks ***, it has exceeded my expectations so far.

hi my name is woody and im a new member.i have a 2011 bx25 with 105 hrs. on the clock.i I am thinking about puting it up for sale but wasnt sure what i should ask. I bought it new.does anyone have...

Here's a few pics of what a BX25 can do. Industrial tires, no chains. Snow banks are about 7 ft tall.

Ok guys- Newbie here and these are my Choices. 1025R vs GC1720 vs BX25 vs emax 22. Personally, I know the JD and Kubota the best. I feel the Kubota is best sized for me, but least performing...

Looks like I may be getting a BX25. I have quite the to do list for it already. Wondering how capable it will be of a few things on the list. I'm looking to get a 4 foot rotary mower for it...

For those BX25 or SCUT owners, I was wondering what pressures you run in the winter for plowing. I have my rear R4 tires loaded and set the pressure by looking at the contact patch method in the...

Hello All, Today while clearing snow my BX25 (less than 50 hours) started to sputter as if it was running out of fuel under load. I shut the motor of and filled the tank with fresh diesel (fuel...

Hello, I have a BX25 that was purchased in 2011 with ~150 hours on it. It recently started to stall out and in doing some research, it appears that it could be a wire, fuel filter, or a blockage...

Figured Id post up my take on adding a couple auxillary hydraulic circuits to the back of my BX. I used an existing Prince valve left over from my firewood processor. It was way overkill for the...

Howdy All, Used up a some scrap stuff and built Breakaway light Brackets for the BX 25 ROPS, No holes drilled in the ROPS..Used Weld Mount product..Great stuff. The Weld mount studs are amazing...

Just some pics of a snow pusher that I had made for my bx25. Made it heavy duty so I could use it for dirt also. I just copied off of the one's they use to clear the parking lots at the malls.

Does anyone have links to companies that specilize and sell Kubota BX25 attachments? Below are the ones I have found so far: 1) Jari Jari USA, Home of the Jari Sickle Mower 2) BxPanded...

Well figured I would post this bucket I built for my BX25 I did about 3 weeks ago. I was tired of it taking forever to dig bigger holes. Only have few pics as I got to involved into the project...

I stumbled across a good video on Youtube. I have no idea if the person that made the video is a member here, but I doubt it since he rented the BX. Enjoy:

Been wanting a horn on the BX for a while. It will be handy for signaling especially considering the kids are usually around when the tractor is running. Not a particularly complicated install...

Hello, I have quite the conundrum. I will be a first time tractor owner, shortly. I am looking at SCUTs with a FEL, MMM, and a backhoe. Uses will be mowing my small yard, moving snow (plan to...

Hello & thanks for welcoming me to the forum. I have a 3 year old BX25 with 165 hours, that starting giving me bogging down issues when I picked up a load or accelerated. It would reduce to idle...

Found all the fittings on the backhoe and FEL but is there any grease fittings on the tractor itself?

Anyone have any recommendations on a make and model of battery for replacement. Original has been good but thought it might be cheaper to go aftermarket than to the dealer. Thoughts?

Before I order a Pat's easy change for by BX25 I was wondering if anybody else had used one on that model of Kubota and if so which category did you order. Thanks in advance!

I went to pick up my tractor from the dealer Saturday. I immediately noticed the new rear case was not painted gray. They left it aluminum without any paint. Was I wrong to question why they...

I went into my local HD last week and noticed a brand new BX25 on a trailer. Thought it may have belonged to a shopper inside. But then realized if was in the stores rental lineup. Thought it was...

Hi, does anyone make either a trailer ball mount or Receiver tube that could mount to the Quick Attach replacing the FEL on a BX25D? I'd like to use the BX for moving a trailer around and seems...

Couldn't get over my old BX25. Miss it so much that I stopped by Barlows today and bought another one. None on the lot but Steve Barlow called last week to factory provided info that Barlows...

Does anyone have experience with this? I have greased and inspected the linkages and all is free and easy. The pedal seems to come back somewhat but then stops short of the last bit and the...

Greetings, getting ready to purchase my first new tractor, a BX25. When I build/price it online it's about $21.5k. When buying locally, what is a reasonable "deal"? Is ~10% off MSRP reasonable...

I heard some clicking and thought it was a u-joint.......obviously not.......five minutes latter BAM! How did this happen?

I was using the PTO today and heard a clicking noise.....five minutes later, BAM! This cannot be good......any idea what happened here guys?

The other day I was using the bucket to lift and pile broken tree limbs. I had been using it couple hours or more doing this when all of sudden there as a high pressure spray leak of fluid from an...

Found a small nick about 4 in from the dist bloc on the boom piston extender hose. Can get at the piston fitting but how the he## do you get at the fitting on the dist bloc? Do you have to take...

Has anyone mounted a grass gobbler, accelerator, type metal side bagger on a BX25 or other SCUT tractor? If they work well on a walk behind they should work the same on a rider. The problem...

After getting my BX25 stuck in our newly discovered natural spring a few weeks ago, I got to thinking that it might be a good idea to use the groundwater for something useful. I am thinking that...

I've been searching for a trenching bucket for my BX25 that is smaller than the factory bucket. I need to run a lot of water lines and I don't want to move more dirt than neccesary. All my...

My new toy was delivered yesterday evening. It was a rainy day, so i didn't really get a chance to play (much). My first project that I had planned was the removal of some tree stumps along the...

For the last four years, I have been using the BX25 around my 1-acre property for pretty light-duty work. It's been mostly grass cutting with the 54" deck with lots of FEL work. I've also got my...

Just thought i would post my bx 25 bx 25d story. i live in north east Oklahoma and recently i have been trying to reduce my monthly bills. so i have been refinancing all of my loans and paying...

I know that there are many knowledgeable folks out there so instead of a big story of the pro's and con's of bucket size, I would just like to put forth the following: An 8" bucket would be useful...

I'm new to this forum, so apologies in advance if this is a mis-post. I purchased a new Kubota BX25D locally two months ago, and decided today to "simply" remove the backhoe, (so I could try out...

Well, my BX25 is four years old and almost paid off. The bucket with the Piranha bar and backhoe have been worth their weight in gold, and the 48" box blade I got earlier this year has been...

I found out about a used Bush Hog that has been sitting unused in a barn for some years. Don't know how old it is and haven't seen it yet. Spare used blade is with it, so thinking they must have...

I been looking at bagged options for my BX25D and am thinking hard about Kubotas bragger or a DR tow behind. I'm sort of leaning toward Kubotas rear system because it is pto powered and a bit more...

I just got my tractor back from being repaired at the dealer. They had to replace the hydraulic pump to fix a horrible screeching noise it was making (that's a whole other story...) Anyway, when...

Hello, Would anyone know if the kubota bx25 has a tpss switch option

Hello, newb here with a question. Please forgive me if this has already been asked as I couldn't find anything to answer my question when I searched. I have a BX25 and a County Line (TSC brand)...

I have a 100' driveway covered in stone. A double-wide gate opens to a stone covered path running alongside my garage and leading to my yard. Behind my garage is also covered in stone. All this...

Been building and pricing my future scut purchase for my up coming projects. I know renting or paying is the best option but I have been thinking of adding a bh to my scut purchase. I do have a...

I had a piece of 1/2" rebar laying around, so I cut it and placed it in the notch in the frame as you see in the picture. Do you think it's strong enough to act as a protector for the steering...

How the HE double hockey sticks do you get those fittings off of the distro box in the back bottom of my BX25 backhoe? The second fitting in on the right , bottom row, (when facing the box) has a...

Hi, guys, I need to figure out how much my 2008 Kubota BX25 with FEL, BH, and 3-pt. hitch depreciated each year, for income tax purposes. I will be able to use a standard Tax Dept. formula of 30%...

Very happy with this tractor. I have the backhoe, loader, front mounted snow blower and mid-mounted mowing deck. No complaints from me yet. I am looking to buy some clamp on forks for the bucket...

I took this video after our last big snow storm. The video show me using my Kubota BX clearing snow from my neighbours driveway. I posted separately in the TBN Build-It-Yourself forum on how I...

I know that several people have done a nice job installing a better filter for the first fuel filter that is prior to the electric pump. And most route the fuel line forward to the new filter...

Just want to chime in and say Hi!. As I have been an avid owner/operator of a 2003 ZD21, I have finally convinced the facilities committee that I work with as the property manager for our church...

I've had my BX25 for 4 years now without the need for a 3 point hitch. But now I am thinking about some rear implements, so I plan to pick one up soon. So my question is this: do I need to buy...

Is this guy on here? Cool flick...... https://www.youtube.com/watch?v=PpU01M98qNw

I am about to receive my new 60" MMM for my BX25. The dealer mentioned installation of "hanging brackets" and he wanted to know if I would be doing it or should he arrange for the shop to do it...

I'm looking to hook a dump cart up to my BX25 (with backhoe off, obviously), and want to get a sanity check on what I plan to do. I also have a question about size and type of hoses. First...

I just completed 400hr service on my BX25D and found this little surprise. Yea. I had a bro-tech skid plate on too...if there is a will there is a way! :mad:

This post is basically about this: If a dealer sells you a tractor he advertised as an "A" but really is a "B" being sold as an "A" and the buyer (me) really didn't know the difference at the...

I made some time this evening to play around with the tractor and install my Wheel Spacers and Skid Plate - both from Bro-tek. Both were well made, but the spacers are absolutely top notch...

Hi all, I'm about to order the 48" EA box blade and thinking about the residential delivery option ($80). They require I be around during a time window and able to unload the blade. I've got a...

Looking at BX25D at the dealer yesterday and noticed a bad 12-18" of weld on the backhoe. My flip phone pics will not do it justice and if it had a good coat of paint on it it wouldn't be noticed...

some time ago i started searching for information regarding block heaters for my BX25. for one reason or another i found a variety of threads with more questions than answers and varying opinions...

I am tired and the bungie cords are tired of holding up my BX25 outriggers. Over time you all know they droop and land on the floor. . If you forget to look at them, they will drag when you take...

Didn't make the trade. Keeping B2620 FEL BH with 39 hours till someone gives me $19,250 for it. Reason for the $750 discount is because of the Kubota discount coupon I rec'd which I can use so...

BX25 Backhoe Thumb vs. Loader Grapple I know the grapple is much more versatile for it's designed used, but how easy is it to pick-up and drive with a small or large log with the BH thumb? What...

Anybody replaced the transmission cooling fan on the bx25? I a looking any hints as I have to replace mine. Thanks

I have a 2008 BX25. I see that Curtis has a new part number cab for 70 series BX tractors, the steel door cab part number is 1KBX70AS. I like the design of it much better than the 1KBX25AS...

So with 400 hrs and several winters on my BX25 I figure it's time to do a DIY cab. I've been on here for some time reading and looking at what others have done and while I do like to work with...

I am shopping for a spare rear and front wheel assembly for my BX25. et e now what you have...

Has anyone out there had any experience with Everything Attachments Compact Tractor Post Hole Digger? Would also appreciate any input on other brands.

I find an auction rotary tiller on ebay. accubic on eBay The accubic RTA48 description say it is comparable with bush hog RTC50G and Phoenix T4 48". Accubic RTA48 Bush Hog RTC50G Phoenix T-4...

We had a pretty good snowfall in SE Mass beginning of January (Thurs into Friday if I recall) My regular days off. My snowblower needed a carburetor, but I have my BX25 going on 4 years now still...

Ok guys, fairly new to this forum, been reading a while but signed up today. Be nice to an old guy with more arthritis than he needs!! BX25 would not start, single digits are fairly rare in...

Anyone try a left side brake pedal conversion yet? I am going to try it when winter is done. It would be fairly easy if not for BH sub-frame being in the way. It looks like just the pedal shaft...

I'm interested in replacing my BX25 seat with a seat that has an adjustable back. Has anyone found one that they are happy with? I would consider OEM or third party. Thanks for looking. Dean

Hi everybody. New to this stuff. From Larsen, Wi. My BX started stalling out at 180 hours. Replaced both fuel filters which corrected the problem. The lower filter did have a lot of black flakes...

I have a BX25 with industrial tires. My driveway is a sheet of ice. I want to get tire chains. I have a few questions: should I get both front and rear or just rear, 2 link or 4, regular or v-bar...

Here's my version of QA forks. They work great. So far the only complaint of the tractor is its loader height. It will barely get over my 1ton box with the bucket. With the QA and forks on it...

I built this cab 2 years ago. It has held up great to the weather. I do only use it in the winter though. It is made out of clear pine and 1/4" luann plywood for the roof. All joints are pocket...

I just boight 27 acres and im thinking of a bigger tractor I have a bx 25 and was thinking of a b or L series with a backhoe does anyone have a b or L searies with a backhoe. I know the b is not...

Hi, Long time reader, 1st time poster. I have a BX25 that I have been doing a few mods over the last year or so. I've made my own Bobcat style QA,fork assy.,and converted an old Bolens 48" blower...

I have a kubota bx25 she stalled on me yesterday and could not get it going again, I have fuel stabalizer in it and stuff. my brother in law came I tried to put a hairdryer on the fuel filter but...

Hello All, This is my first post. I joined 6 months ago and have been lurking a long time before that. Just trying to absorb all the knowledge here. I finally got the wife on board for a...

I have a kubota bx25 she stalled on me yesterday and could not get it going again, I have fuel stabalizer in it and stuff. my brother in law came I tried to put a hairdryer on the fuel filter but...

I found some of this on orangetractor forum. Some is edits from TBN members. 1520 - Tractor 628 - BH Backhoe 22 - 8 inch BH bucket 375 - FEL Loader 132 - FEL bucket _________________ 2677...

I have a BX25 its 3 or 4 years old has around 140 hours on it. about 2 weeks ago I started it up and it turned over and ran fine for about 5 minutes then it started sputtering and stalled. I could...

Hello all, It's been a few years since I've browsed these forums, but when I did, I read some great advice that led to my purchase of a BX25. For the last three years, it has been a godsend...

Looking for a rear blade for my BX25. I see King Kutter makes a 50 XB model but would like to find a 6' blade. Would the 6' King Kutter work? I saw a Bush Hog 6' (3506) blade that I really...

had an idea and created them today. held in by 2 bolts and 2 pins they are easily removed. Also all the forks are pinned in so that if I need a longer fork , I just need to pull them out and put...

Well I think I finished getting ready for winter (tractor wise). Finally decided it was time to remove the BH for the first time and install the 3pt hitch. It was a good day today with my son...

Just wondering what I need to do to put away my bx, this is the first winter that I will have had it. It will be stored in an unseated garage. So what do I need to do to "winterize" it ? Thanks

Hey all, Been reading this website for years. I bought a used bx25 and have been going over everything. One concern is the brake pedal which seems to have too much free travel. The manual says...

Hello everybody, Newbie here. I have been reading this site for several years. Finally have a 2012 bx25. Used, from a private seller. Changed all fluids at 51 hours. Concerned with the brake...

Ok I know there not equals but this is what ive gotten down to wanting to buy. The Kubota bx 25 with loader and backhoe is 18,500 with 0 interest for 60 mos. The Mahindra max22 with loader and...

Hi. Is there a way to find a catalogue with all the parts and numbers of a Kubota bx25 so I can choose a better place to buy than in my area, Puerto Rico? It seems to me that the mark up in my...

Anybody know what model# Sweeper goes on the quick hitch on the BX25? The website is very unhelpful at helping to determine these things. Thanks!

OK I have had my BX25 for a little over a year and have not installed the 3 point hitch kit that I bought to go with it. I still have not purchased that tiller for the thing. My question is....do...

Can anyone tell me if they know of a flail mower that is compatible with a BX25?

Hello Has anyone seen the new BX25 factory thumb for sale online from any of the online Kubota dealers? ORDER CODE BX6316 Mechanical Thumb (BT602 Only) FACTORY NUMBER K292B50 suggested list...

Has anybody had experience with the Rock Bucket from Jari? Looks good. I was thinking that on the front and a landscape rake on the back would be a great landscaping setup for my BX25. Any other...

Can someone tell me what the color codes are for the FEL hoses on a BX25? Which 2 are for the curl cylinder and which 2 are for the lift? Thanks.

Just found this site and was hoping someone could help me find a grass bagger adapter for a 60" mower deck for my BX25 so that I could attach it to a leaf vac. Thanks

Looking to put wheel spacers on my BX25. I thought Bro-Tek sold spacers, but I don't see any on their website. Anybody have any experience with these, from "The Tracks Company"? Kubota John...

Has anyone had a problem with the cutting height knob. Mine is difficult (to say the least) to put into the lock position, it moves easily from the 0 to 4 but going from the 4 to the locked up is...

I've always said don't ever buy anything I've owned. I use it to the extent it would make the engineers who designed it cringe. I've got a G1800 now and love the machine. Might even cry when I...

I'm thinking about selling my Kubota BX25. It has about 190 hours. Excellent condition. Extras include OEM 3 pt. hitch adapter,a thumb, fork lift attachment and skid plate. It still looks...

I may have asked this question before but now that my plugger is but a week away I'm getting nervous. It will attach to my three point hitch on my BX 25 (not the "D") I will keep the FEL on for...

As a condition of upgrading to the 25D my wife said she wanted a bagger, if that痴 all it takes I知 in. The dealer cut me a good deal if I壇 assemble it myself so too easy,,,so I thought. Comes in...

Started grading the dirt around my new shop this past weekend! I was pleasantly surprised at how quickly the BX did the job. I think it would have went faster with a box blade rather than the rear...

I've got a problem with my BX that has me perplexed. Last fall while mowing the tractor started to occasionally sputter and lose power, mostly when pointed uphill. A quick search here pointed to...

Sorry for the mundane question that you have all already answered a gazillion times. And it may already be too late to ask since I have about 30 hours on the BX now. I have been running it...

I am new to owning a Kubota tractor and was wondering if a Model RCK54-22BX series mower deck would fit on my bx 25. Any help with rhis woulde be great. Found one for sale rather cheap. Thanks...

About a year ago I bought a used L3400 HST 4wd w/ loader. My jd L130 riding mower is on its last leg. Here are my options> 1. Buy a Toro zero turn - keep L3400 , 5-foot bush hog, 58 inch RTR...

Looking to buy a posthole digger w/9" auger for my BX 25. Recommendations?

Anyone have one of these for their BX? BOG For some odd reason I seem to have a fascination with grapples, they just look extremely useful. :D No tractor, but would love a BX25, and also to...

I'm getting ready to change the oil in my BX25 and interested in what everyone is using in their 25's. I've been using Kubota brand 10-30 but would like to find a synthetic. I've used the search...

Ok guys, I need some help please. I previously owned a BX2200. Sold it a couple years ago. Missed it terribly. Wife let me buy a new BX25 yesterday. Put about 4 hours on it today mowing and...

Sold my JD x320, which was a really good mower and upgrading to the Kubota BX25. Hopefully the 1' more deck will help in mowing and plan on planting 50 or more trees, the back hoe option should...

So I'm looking at buying a Wallenstein WX310 3ph log splitter for my Kubota BX25. I want to run the splitter off of the power beyond hoses that are used for the backhoe. I don't know a lot about...

Hello everyone, just found the TBN forum site, it is great. I have owned my bx25 since last spring, lots of projects completed, many more upcoming! No problems with the bx at all! It is an awesome...

Here is a video I just made of a Rossi sickle mower on my BX25, mowing around ponds and cutting cedar saplings on a steep hill. It was my first use of this thing so I'm slow and still getting used...

I am looking to add rear remotes on my BX25 for the main purpose of having power angle on my rear blade. I will probably find other reasons down the road but thats the main one right now. I know...

:)Looking at bx25d @ 15k or b21 at 18k what is best, thanks

Rapid fuelling potato cannon mounted on Kubota tractor

I'm looking for a 3PH Kit for my BX25. Dealer 1 wants ~$360. Dearler 2 and 3 want $218 + $40 shipping! and said it'll take 1 or 2 weeks to get it. Is there an after market one I can get cheaper...

does anyone know if they make a bucket for the bx25 for digging in rocky soil? i am in the process of moving any was digging a ditch for my water line and the rocks are to much for the little...

This machine has only 16 hours, close to my house and I need it. What would be a fair price to offer on this machine? kubota bx25 loader Thanks for any advice. Steve

Hi all, I've been lurking for a while but never got around to registering. There's been a few times lately where I've wanted to respond to a post but remembered that I didn't have a membership...

Hi, I am new to the forum. I bought a new BX25 and would like to install a small class 1 wood splitter. The one I am looking at getting is the 13 ton from Northern Tools. My question is...

OK, new to tractors here, and have a very basic understanding of hydraulics, and none when it comes to the way it's used in the BX25. I'm thinking of buying an Enorossi BFT135 5'ft sickle mower...

The electrical interlocks will not allow me to get off the seat to operate the chipper with the PTO engaged. Is there some little quirk I am missing or do I need to install a bypass switch around...

I do quite a bit of dirt road maintenance (1.1 mile long) with my BX and I've had a couple of close calls with vehicles even though the posted speed is 20 and I have all my lights on, day or...

What are the differences, if any, between the FEL on a BX25D and the FEL on a BX25 or BX24? Not including the QA. Any design, structural or metal size differences? Cylinder size? TIA

I just went through the process of adding a proper spin on filter to my BX. As you may or may not be aware, the factory filters are in line, plastic jobbies that are more fitting on a snowmobile...

Tipped my BX25 FEL & BH on its side - what precautions to take before starting engine Hi People - tipped my BX25 on it' side this afternoon. Upright again OK but engine doesn't ant to turn...

I pulled out the eleven plastic "Christmas tree" ribbed shank fasteners that hold down the rubber floor mat and pulled up the mat. After four years, a layer of mud and water was under there but it...

i went with the small ones (1.25") due to the clearances on my 54" mower. most of my annual hours are accumulated mowing and i wanted spacers that i could install and forget. i installed them...

Greetings: I'm new as a poster but a longtime reader who, like many others, has benefitted tremendously from the wealth of information available on this forum. So, thanks for what you've already...

grapple for my bx25, any suggestions or ideas ,1 that is easy to install this is all new me

Yep, had my BX25 now for a little over 6 months and love it. Sank it twice in the mud (that was fun) and done TONS with it. This Saturday I ran over a small section of my property that had some...

I have the Kubota ballast box for my BX25 and it won't lower enough to sit on the ground for removal. I have to put 4 X 4's or cement blocks under it to set it down. I also spent a short time...

I need opinions on rops lighting for my BX25. The brightest is what I'm going for.

I am debating whether to purchase a Kubota front mounted snow blower or a front mounted blade for my BX25. Advantages or disadvantages of either?

I recently replaced my Bx2200 with a new BX 25 and added the front snow blower. Now my shed is overflowing. I have the blower in the garage in front of my car right now but the loader won't fit...

DO you have a BX25 and are you running a flail? I sure would like your input if so, what flavor etc your runnin' and would you buy it again kinda thing... I have a job where I need to knock down...

Been reading this forum since a little before I bought my bx25 a year ago, and I appreciate all the tips I`ve picked up. So far at 140 hours I`ve only had two issues, both were a result of nuts...

I've had my used BX25 (500hrs.) for a few weeks now, but it's having itermittent engine issues. After running it for a few minutes, sometimes the RPM drops to <1000rpm and stays there. Sometimes...

Hi, I have used this site and a couple of others to research the BX25, CS2410, and 1026R. My 2012 BX25 will be delivered next week. I live in Newfoundland, Canada and will primarily use the...

Couldn"t spend a lot of money on a blower to clean up around the yard. so I made this. works pretty well

So I just bought a used BX25 and love it so far. However, I am having problems getting the mid-mount-mower to lock in the upmost position... no matter what I do it raises and lowers when I raise...

Do YOU have a flail mower on your BX25? If so what model did you buy and would you buy the same size flail again? Are you under powered? What size is your flail as well...please. ?

Can anyone tell me where a BX25 is manufactured and assembled? I was told in the USA.

I am trying to find a belly mower that fits a bx25 without modding. Any size deck will work for the right price. $1,500 for a new one is just hard to take. Paying $2,000-$2,500 for a bagger is...

Which brands and sizes would work the best? Any deals out there?

Which brands and sizes would work the best? All opinions welcome. Any deals out there?

I have a BX25 with 30 hours on it. When it's running and on an incline to the left it makes a knocking noise. Seems to be worst at idle and gets less as the rpm increases. The noise seems to be...

Does anyone out there have the HST hydraulic schematic for the BX25/xx60 line? I believe that the WSM contains this. I posed this question in another post but it was buried and I doubt many saw...

Greetings, Ladies and Gents! My first post here, though I've been lurking for the past 12-15 months. I致e learned a lot from reading the various forums on this site. Thanks!:thumbsup: Just bought...

Doing some planning in the garage, what is the total length of a BX25 with the front bucket and the Backhoe attached Thanks